IPL g77fc04e D-15 HW Reset SPI 54M 64MB BIST0_0001-OK MXP found at 0x0000f000 offset:00004400 Checksum OK IPL_CUST g77fc04e MXP found at 0x0000f000 offset:00010000 XZ decomp_size=0x0002b4fc Version: I6gf70feaf DRAM: WARNING: Caches not enabled Using default environment In: serial Out: serial Err: serial ******************************************* board_late_init for upgrade image gpio debug MHal_GPIO_Pad_Set:603 gpio[54] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[55] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[56] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[57] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[58] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[59] is 0 ******************************************* ******************************************* factory_boot gpio/pwm init Flash is detected (0x0C07, 0x20, 0x70, 0x17) SF: Detected nor0 with total size 8 MiB SF: 256 bytes @ 0x30000 Read: OK gpio/pwm count: 3 gpio init: gpio output 46 1 gpio debug MHal_GPIO_Pad_Set:603 gpio[46] is 1 gpio init: gpio output 47 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[47] is 0 gpio init: gpio output 61 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[61] is 0 ******************************************* Net: MAC Address 00:00:23:34:45:68 Auto-Negotiation... Link Status Speed:100 Full-duplex:1 sstar_emac Autobooting in 1 seconds Uip boot... Firmware check pass! Flash is detected (0x0C07, 0x20, 0x70, 0x17) SF: Detected nor0 with total size 8 MiB SF: 131072 bytes @ 0x60000 Read: OK [XZ] !!!reserved 0x21000000 length=0x 1000000 for xz!! XZ params: in_addr 0x21000040,in_size 0x20000, out_addr 0x220a0000, out_size 0x4 0000 XZ: uncompress ret 7, size = 262144 ## Starting application at 0x220A0000 ... U-Boot 2015.01 (Aug 30 2022 - 19:06:44), Build: jenkins-tapo_c110v1_iot-6 Version: I6gd1dfee1 DRAM: WARNING: Caches not enabled Using default environment In: serial Out: serial Err: serial ******************************************* board_late_init for upgrade image gpio debug MHal_GPIO_Pad_Set:603 gpio[54] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[55] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[56] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[57] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[58] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[59] is 0 reset wifi gpio debug MHal_GPIO_Pad_Set:603 gpio[16] is 0 gpio debug MHal_GPIO_Pad_Set:603 gpio[16] is 1 ******************************************* Net: MAC Address XX:XX:XX:XX:XX:XX Auto-Negotiation... Link Status Speed:100 Full-duplex:1 sstar_emac Warning: sstar_emac using MAC address from net device Flash is detected (0x0C07, 0x20, 0x70, 0x17) SF: Detected nor0 with total size 8 MiB SF: 8388608 bytes @ 0x0 Read: OK ------md5 check failed----- Flash is detected (0x0C07, 0x20, 0x70, 0x17) SF: Detected nor0 with total size 8 MiB SF: 3145728 bytes @ 0x80000 Read: OK ## Booting kernel from Legacy Image at 20008200 ... Image Name: Linux-4.9.84 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1465528 Bytes = 1.4 MiB Load Address: 20008000 Entry Point: 20008000 Verifying Checksum ... OK Loading Kernel Image ... OK atags:0x20000000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.84 (root@smartlifeci1) (gcc version 4.9.4 (Buil droot 2017.08-gc7bbae9-dirty) ) #2 PREEMPT Tue Aug 30 19:24:25 CST 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c53c7d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] early_atags_to_fdt() success [ 0.000000] OF: fdt:Machine model: INFINITY6B0 SSC009A-S01A QFN88 [ 0.000000] LXmem is 0x3fe0000 PHYS_OFFSET is 0x20000000 [ 0.000000] Add mem start 0x20000000 size 0x3fe0000!!!! [ 0.000000] [ 0.000000] LX_MEM = 0x20000000, 0x3fe0000 [ 0.000000] LX_MEM2 = 0x0, 0x0 [ 0.000000] LX_MEM3 = 0x0, 0x0 [ 0.000000] EMAC_LEN= 0x0 [ 0.000000] DRAM_LEN= 0x0 [ 0.000000] deal_with_reserve_mma_heap memblock_reserve success mma_config[0] .reserved_start= [ 0.000000] 0x22de0000 [ 0.000000] [ 0.000000] cma: Reserved 2 MiB at 0x22a00000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 11652 [ 0.000000] Kernel command line: console=ttyS0,115200n8r androidboot.console= ttyS0 root=/dev/mtdblock6 rootfstype=squashfs noinitrd init=/etc/preinit LX_MEM= 0x3FE0000 mma_heap=mma_heap_name0,miu=0,sz=0x1200000 mma_memblock_remove=1 os_si ze=1465592 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 41300K/46976K available (1937K kernel code, 204K rwdata, 492K rodata, 96K init, 139K bss, 3628K reserved, 2048K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc3000000 - 0xff800000 ( 968 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc2de0000 ( 45 MB) [ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB) [ 0.000000] .text : 0xc0008000 - 0xc01ec6d8 (1938 kB) [ 0.000000] .init : 0xc0284000 - 0xc029c000 ( 96 kB) [ 0.000000] .data : 0xc029c000 - 0xc02cf260 ( 205 kB) [ 0.000000] .bss : 0xc02d1000 - 0xc02f3ea8 ( 140 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ms_init_main_intc: np->name=ms_main_intc, parent=gic [ 0.000000] ms_init_pm_intc: np->name=ms_pm_intc, parent=ms_main_intc [ 0.000000] ss_init_gpi_intc: np->name=ms_gpi_intc, parent=ms_main_intc [ 0.000000] Find CLK_cpupll_clk, hook ms_cpuclk_ops [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 6.00MHz (vir t). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1623fa770, max_idle_ns: 440795202238 ns [ 0.000006] sched_clock: 56 bits at 6MHz, resolution 166ns, wraps every 43980 46511055ns [ 0.000020] Switching to timer-based delay loop, resolution 166ns [ 0.297255] console [ttyS0] enabled [ 0.300737] Calibrating delay loop (skipped), value calculated using timer fr equency.. 12.00 BogoMIPS (lpj=60000) [ 0.310999] pid_max: default: 4096 minimum: 301 [ 0.315604] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.322155] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.329803] CPU: Testing write buffer coherency: ok [ 0.334733] Setting up static identity map for 0x200081c0 - 0x200081f0 [ 0.342505] devtmpfs: initialized [ 0.362191] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.370062] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.379886] futex hash table entries: 16 (order: -4, 448 bytes) [ 0.386449] NET: Registered protocol family 16 [ 0.391524] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.400101] [ 0.400101] [ 0.400101] Version : MVX4##I6B0gd1dfee1KL_LX409##[BR:HEAD]#XVM [ 0.400101] [ 0.422422] GPIO: probe end[ 0.426062] [ss_gpi_intc_domain_alloc] hw:42 -> v:49 [ 0.432673] [MS_PM_INTC] hw:20 -> v:52 [ 0.449396] usbcore: registered new interface driver usbfs [ 0.455689] usbcore: registered new interface driver hub [ 0.461046] usbcore: registered new device driver usb [ 0.471866] clocksource: Switched to clocksource arch_sys_counter [ 0.479897] NET: Registered protocol family 2 [ 0.485347] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.492303] TCP bind hash table entries: 1024 (order: 2, 20480 bytes) [ 0.498630] TCP: Hash tables configured (established 1024 bind 1024) [ 0.505121] UDP hash table entries: 128 (order: 0, 6144 bytes) [ 0.510811] UDP-Lite hash table entries: 128 (order: 0, 6144 bytes) [ 0.517271] NET: Registered protocol family 1 [ 0.522884] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.541044] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.546871] jffs2: version 2.2. © 2001-2006 Red Hat, Inc. [ 0.556854] io scheduler noop registered [ 0.560622] io scheduler deadline registered (default) [ 0.567750] libphy: Fixed MDIO Bus: probed [ 0.572745] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.579122] Mstar_ehc_init version:20180309 [ 0.583380] ehci monitor start running [ 0.587163] Sstar-ehci-1 H.W init [ 0.590369] Get power-enable-pad from DTS GPIO(16) [ 0.595298] Titania3_series_start_ehc start [ 0.599317] [USB] config miu select [70] [e8] [ef] [ef] [ 0.604579] [USB] enable miu lower bound address subtraction [ 0.610194] [USB] init squelch level 0x2 [ 0.615150] [USB] no platform_data, device tree coming [ 0.620131] [USB][EHC] dma coherent_mask 0xffffffffffffffff mask 0xffffffffff ffffff [ 0.627841] BC disable [ 0.630226] [USB] soc:Sstar-ehci-1 irq --> 43 [ 0.634612] Sstar-ehci-1 soc:Sstar-ehci-1: EHCI Host Controller [ 0.640528] Sstar-ehci-1 soc:Sstar-ehci-1: new USB bus registered, assigned b us number 1 [ 0.648811] Sstar-ehci-1 soc:Sstar-ehci-1: irq 43, io mem 0xfd284800 [ 0.682027] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.688666] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 0.695905] usb usb1: Product: EHCI Host Controller [ 0.700762] usb usb1: Manufacturer: Linux 4.9.84 ehci_hcd [ 0.706182] usb usb1: SerialNumber: mstar [ 0.710955] hub 1-0:1.0: USB hub found [ 0.714766] hub 1-0:1.0: 1 port detected [ 0.718960] i2c /dev entries driver [ 0.723343] 1f221000.uart0: ttyS0 at MMIO 0x0 (irq = 37, base_baud = 10800000 ) is a unknown [ 0.732270] 1f221200.uart1: ttyS1 at MMIO 0x0 (irq = 38, base_baud = 10800000 ) is a unknown [ 0.741155] 1f220400.uart2: ttyS2 at MMIO 0x0 (irq = 40, base_baud = 10800000 ) is a unknown [ 0.751121] MSYS: DMEM request: [emac0_buff]:0x00000812 [ 0.756687] MSYS: DMEM request: [emac0_buff]:0x00000812 success, CPU phy:@0x2 2A47000, virt:@0xC2A47000 [ 0.766738] libphy: mdio: probed [ 0.769816] mdio_bus mdio-bus@emac0: /soc/emac0/mdio-bus/ethernet-phy@0 has i nvalid PHY address [ 0.778722] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 0 [ 0.785693] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 1 [ 0.792335] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 2 [ 0.798804] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 3 [ 0.805470] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 4 [ 0.812064] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 5 [ 0.818648] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 6 [ 0.825380] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 7 [ 0.831908] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 8 [ 0.838493] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 9 [ 0.845131] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 10 [ 0.851809] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 11 [ 0.858523] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 12 [ 0.865223] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 13 [ 0.871925] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 14 [ 0.878616] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 15 [ 0.885329] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 16 [ 0.892030] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 17 [ 0.898721] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 18 [ 0.905434] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 19 [ 0.912136] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 20 [ 0.918827] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 21 [ 0.925540] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 22 [ 0.932291] ==20180309==> hub_port_init 1 #0 [ 0.932293] Plug in USB Port1 [ 0.939458] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 23 [ 0.946185] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 24 [ 0.952872] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 25 [ 0.959560] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 26 [ 0.966274] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 27 [ 0.972975] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 28 [ 0.979666] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 29 [ 0.986379] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 30 [ 0.993080] mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 31 [ 0.999866] [emac_phy_connect][3337] connected mac emac0 to PHY at mdio-bus@e mac0:00 [uid=11112222, driver=SStar 10/100 Ethernet Phy] [ 1.013378] [gpioi2c] sda-gpio=8, scl-gpio=9 [ 1.019571] MSYS: DMEM request: [BDMA_FSP_WBUFF]:0x00010040 [ 1.025491] MSYS: DMEM request: [BDMA_FSP_WBUFF]:0x00010040 success, CPU phy: @0x22A50000, virt:@0xC2A50000 [ 1.035059] [Ser flash] phys=0x22a50000, virt=0xc2a50000, bus=0x02a50000 len: 0x10040 [ 1.043294] [FSP] Flash is detected (0x0C07, 0x20, 0x70, 0x17) ver1.1 [ 1.049579] [FSP] 1-1-4 QUAD_READ MODE [ 1.053437] mtd .name = NOR_FLASH, .size = 0x00800000 (8MiB) [ 1.053437] .erasesize = 0x00010000 .numeraseregions = 0 [ 1.064422] SLP flash nor read [ 1.067868] hdrA:1466368,B:1991168,C:2465280 [ 1.072018] Searching for RedBoot partition table [ 1.076689] 10 RedBoot partitions found on MTD device NOR_FLASH [ 1.082614] partitions[0] = {.name = factory_boot, .offset = 0x00000000, .siz e = 0x0002d800 (182KiB) } [ 1.091923] partitions[1] = {.name = factory_info, .offset = 0x0002d800, .siz e = 0x00002800 (10KiB) } [ 1.101138] partitions[2] = {.name = art, .offset = 0x00030000, .size = 0x000 10000 (64KiB) } [ 1.109591] partitions[3] = {.name = config, .offset = 0x00040000, .size = 0x 00020000 (128KiB) } [ 1.118402] usb 1-1: new high-speed USB device number 2 using Sstar-ehci-1 [ 1.125320] partitions[4] = {.name = normal_boot, .offset = 0x00060000, .size = 0x00020000 (128KiB) } [ 1.134493] partitions[5] = {.name = kernel, .offset = 0x00080000, .size = 0x 00166200 (1432KiB) } [ 1.143364] partitions[6] = {.name = rootfs, .offset = 0x001e6200, .size = 0x 00259e00 (2407KiB) } [ 1.152243] partitions[7] = {.name = rootfs_data, .offset = 0x00440000, .size = 0x003bfe00 (3839KiB) } [ 1.161542] partitions[8] = {.name = verify, .offset = 0x007ffe00, .size = 0x 00000200 (0KiB) } [ 1.170172] partitions[9] = {.name = firmware, .offset = 0x00080000, .size = 0x00780000 (7680KiB) } [ 1.179415] Creating 10 MTD partitions on "NOR_FLASH": [ 1.184458] 0x000000000000-0x00000002d800 : "factory_boot" [ 1.189888] mtd: partition "factory_boot" doesn't end on an erase block -- fo rce read-only [ 1.199472] 0x00000002d800-0x000000030000 : "factory_info" [ 1.205106] mtd: partition "factory_info" doesn't start on an erase block bou ndary -- force read-only [ 1.215438] 0x000000030000-0x000000040000 : "art" [ 1.221456] 0x000000040000-0x000000060000 : "config" [ 1.227799] 0x000000060000-0x000000080000 : "normal_boot" [ 1.235030] 0x000000080000-0x0000001e6200 : "kernel" [ 1.239841] mtd: partition "kernel" doesn't end on an erase block -- force re ad-only [ 1.249198] 0x0000001e6200-0x000000440000 : "rootfs" [ 1.254363] mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only [ 1.264296] 0x000000440000-0x0000007ffe00 : "rootfs_data" [ 1.269542] mtd: partition "rootfs_data" doesn't end on an erase block -- for ce read-only [ 1.279402] 0x0000007ffe00-0x000000800000 : "verify" [ 1.284512] mtd: partition "verify" doesn't start on an erase block boundary -- force read-only [ 1.294415] 0x000000080000-0x000000800000 : "firmware" [ 1.301283] MSYS: DMEM request: [AESDMA_ENG]:0x00001000 [ 1.306956] MSYS: DMEM request: [AESDMA_ENG]:0x00001000 success, CPU phy:@0x2 2A48000, virt:@0xC2A48000 [ 1.316596] MSYS: DMEM request: [AESDMA_ENG1]:0x00001000 [ 1.321805] MSYS: DMEM request: [AESDMA_ENG1]:0x00001000 success, CPU phy:@0x 22A49000, virt:@0xC2A49000 [ 1.332326] [ms_cpufreq_init] Current clk=799999872 [ 1.337980] [NOTICE]Each grp bit0 must be enabled! [ 1.343153] [NOTICE]pwm-isr(53) success. If not i6e or i6b0, pls confirm it o n .dtsi [ 1.351277] Registered character driver slp_flash_chrdev [ 1.356626] SLP flash cdev init! NOR_FLASH[ 1.361820] NET: Registered pro tocol family 17 [ 1.366637] Bridge firewalling registered [ 1.370930] ThumbEE CPU extension supported. [ 1.375708] OF: fdt:not creating '/sys/firmware/fdt': CRC check failed [ 1.385073] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 1.392883] usb 1-1: New USB device found, idVendor=007a, idProduct=8888 [ 1.399449] usb 1-1: New USB device strings: Mfr=16, Product=32, SerialNumber =0 [ 1.408042] usb 1-1: Product: AltoBeam_WIFI [ 1.412121] usb 1-1: Manufacturer: AltoBeam inc. [ 1.418803] devtmpfs: mounted [ 1.421645] This architecture does not have kernel memory protection. [ 1.699397] random: preinit: uninitialized urandom read (4 bytes read) [ 1.706148] random: mdev: uninitialized urandom read (4 bytes read) [ 1.837204] random: busybox: uninitialized urandom read (4 bytes read) [ 1.847925] random: busybox: uninitialized urandom read (4 bytes read) [ 1.859198] random: awk: uninitialized urandom read (4 bytes read) [ 1.870259] random: busybox: uninitialized urandom read (4 bytes read) [ 1.881611] random: grep: uninitialized urandom read (4 bytes read) [ 1.892206] random: grep: uninitialized urandom read (4 bytes read) [ 1.903272] random: grep: uninitialized urandom read (4 bytes read) [ 1.914370] random: mkdir: uninitialized urandom read (4 bytes read) - preinit - mounting rwroot - init - Please press Enter to activate this console. [ 2.964025] k_netlink_ipc: loadi ng out-of-tree module taints kernel. [ 3.070001] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.102003] [emac_phy_link_adjust] EMAC Link Up Tue Aug 30 21:23:55 GMT 2022 reset_gpio = 66 ===insmod /lib/modules/4.9.84/k_hi_reset.ko=== [ 5.540883] Success to init gpio reset led_green_gpio = 47 led_red_gpio = 46 led_green_active_low = 0 led_red_active_low = 0 ===insmod /lib/modules/4.9.84/gpio_leds.ko=== Command failed: Unknown error Starting wlan-manager: wlan-manager started. find usb device ok wlan-manager: driver is not ready, wait... [ 6.390619] br-wan: port 1(eth0) entered blocking state [ 6.395790] br-wan: port 1(eth0) entered disabled state [ 6.401183] device eth0 entered promiscuous mode [ 6.406317] br-wan: port 1(eth0) entered blocking state [ 6.411389] br-wan: port 1(eth0) entered forwarding state [ 6.417351] [MDev_EMAC_ndo_change_mtu][3421] change mtu size from 1500 to 148 0 [ 6.601130] wlan-manager: insmod atbm6032i_wifi_usb.ko... [ 6.843485] [atbm_log]:atbm_usb_module_init 0 [ 6.847700] [atbm_log]:SVN_VER=17552,DPLL_CLOCK=2,BUILD_TIME=[===USB-ARES_B== [ 6.855127] [atbm_log]:Probe called -1 v1 [ 6.858992] [atbm_log]:CONFIG_USE_DMA_ADDR_BUFFER TX_BUFFER_SIZE 800 [ 6.865571] [atbm_log]:CONFIG_USB_AGGR_URB_TX enable cnt tx_dma_addr_buffer_e nd( (null))tx_dma_addr_buffer( (null)),0 [ 6.876348] [atbm_log]:atbm_usb_urb_malloc CONFIG_USE_DMA_ADDR_BUFFER max_num 4, total 131072 [ 6.885063] [atbm_log]:CONFIG_USB_AGGR_URB_TX enable cnt tx_dma_addr_buffer_e nd(c2a70000)tx_dma_addr_buffer(c2a90000),8 [ 6.895868] [atbm_log]:CONFIG_TX_NO_CONFIRM [ 6.899916] [atbm_log]:Allocated hw_priv @ c20210a0 [ 6.905173] [atbm_log]:atbmwifi USB_USE_TASTLET_TXRX enable (c20210a0) [ 6.911550] [atbm_log]:atbmwifi USB_USE_TASTLET_TXRX enable (c20210a0) [ 6.918249] [atbm_log]:atbm_before_load_firmware++ [ 6.923178] [atbm_log]:+++++++++++++++++1.1v++++++++++++++++++ [ 6.928854] [atbm_log]:===================~_~==================== [ 6.935653] [atbm_log]:atbm_start_load_firmware++ [ 6.940196] [atbm_log]:used firmware.h= [ 6.944158] [atbm_log]:START DOWNLOAD ICCM========= [ 6.948903] [atbm_log]:atbm_load_firmware_generic: addr 10000: len 22000 [ 6.966714] random: fast init done ---WLAN---ethernet boot OK [ 7.104854] [atbm_log]:START DOWNLOAD DCCM========= [ 7.109584] [atbm_log]:atbm_load_firmware_generic: addr 800000: len 8000 [ 7.148546] [atbm_log]:atbm_after_load_firmware++ [ 7.153538] [atbm_log]:0x1610102c=0x4020e [ 7.157643] [atbm_log]:0x1610102c=0x1020f [ 7.161551] [atbm_log]:0x16101000=0x8000e08 [ 7.167618] [atbm_log]:set_block_size=256 [ 7.171509] [atbm_log]:firmwareCap f5a9 [ 7.171513] [atbm_log]:firmwareCap2 51ae [ 7.171533] [atbm_log]:wsm_caps.firmwareCap 51aef5a9 [ 7.171534] [atbm_log]:apollo wifi WSM init done. [ 7.171534] Input buffers: 32 x 2048 bytes [ 7.171534] Hardware: 7.1280 [ 7.171534] WSM firmware [=MODEM=RF=Ares_AX 2GHZ Apr 1 2022 15:40:58NOTX Confrim], ver: 11513, build: 2735, api: 1060, cap: 0x51AEF5A9 Config[30004] exp ection 900b5c0, ep0 cmd addr 901ce2c NumOfStations[4] NumOfInterfaces[3] [Debug] [setLedEvent:429] setLedEvent = 4 [Debug] [main:577] gLastLedEvent = 1, gCurrLedEvent = 4 [ 7.171538] [atbm_log]:EFUSE(8) [0] [ 7.171541] [atbm_log]:EFUSE(I) [1] [ 7.171544] [atbm_log]:EFUSE(B) [0] [ 7.171547] [atbm_log]:CAPABILITIES_ATBM_PRIVATE_IE [0] [ 7.171550] [atbm_log]:CAPABILITIES_NVR_IPC [0] [ 7.171553] [atbm_log]:CAPABILITIES_NO_CONFIRM [1] [ 7.171556] [atbm_log]:CAPABILITIES_SDIO_PATCH [0] [ 7.171559] [atbm_log]:CAPABILITIES_NO_BACKOFF [1] [ 7.171562] [atbm_log]:CAPABILITIES_CFO [0] [ 7.171564] [atbm_log]:CAPABILITIES_AGC [1] [ 7.171567] [atbm_log]:CAPABILITIES_TXCAL [1] [ 7.171570] [atbm_log]:CAPABILITIES_MONITOR [0] [ 7.171573] [atbm_log]:CAPABILITIES_CUSTOM [1] [ 7.171575] [atbm_log]:CAPABILITIES_SMARTCONFIG [0] [ 7.171578] [atbm_log]:CAPABILITIES_ETF [1] [ 7.171581] [atbm_log]:CAPABILITIES_LMAC_RATECTL [1] [ 7.171584] [atbm_log]:CAPABILITIES_LMAC_TPC [1] [ 7.171587] [atbm_log]:CAPABILITIES_LMAC_TEMPC [1] [ 7.171589] [atbm_log]:CAPABILITIES_CTS_BUG [0] [ 7.171592] [atbm_log]:CAPABILITIES_USB_RECOVERY_BUG [1] [ 7.171595] [atbm_log]:CAPABILITIES_USE_IPC [1] [ 7.171598] [atbm_log]:CAPABILITIES_OUTER_PA [0] [ 7.171601] [atbm_log]:CAPABILITIES_POWER_CONSUMPTION [1] [ 7.171604] [atbm_log]:CAPABILITIES_RSSI_DECIDE_TXPOWER [0] [ 7.171606] [atbm_log]:CAPABILITIES_RTS_LONG_DURATION [1] [ 7.171609] [atbm_log]:CAPABILITIES_TX_CFO_PPM_CORRECTION[1] [ 7.171612] [atbm_log]:CAPABILITIES_SHARE_CRYSTAL [0] [ 7.171615] [atbm_log]:CAPABILITIES_HW_CHECKSUM [0] [ 7.171618] [atbm_log]:CAPABILITIES_SINGLE_CHANNEL_MULRX [0] [ 7.171621] [atbm_log]:CAPABILITIES_CFO_DCXO_CORRECTION [1] [ 7.171623] [atbm_log]:CONFIG_PRODUCT_TEST_USE_FEATURE_ID [1] [ 7.171626] [atbm_log]:CONFIG_PRODUCT_TEST_USE_GOLDEN_LED [1] wlan-manager: dr[ 7.497158] [atbm_log]:mdelay wait wsm_startup_done !! iver is not ready, wait... [ 7.506575] [atbm_log]:WSM_FIRMWARE_CHECK_ID [ 7.511081] [atbm_log]:wsm_generic_confirm:status(2) [ 7.516135] [atbm_log]: wsm_write_mib fail !!! mibId=4132 [ 7.522464] [atbm_log]:apollo wifi : can't open /tmp/radio/mac_address [ 7.528849] initmac(AC:15:A2:42:2B:19),mac(AC:15:A2:42:2B:19) ---WLAN---renew [ 7.535506] [atbm_log]:efuse data is [0x1,0x28,0x1b,0x1c,0x1d ,0x8,0x0,0x0,0xac:0x15:0xa2:0x42:0x2b:0x19] ip [ 7.555128] [atbm_log]:apollo wifi : can't open /tmp/radio/atbm_txpwer_dcxo_c fg.txt [ 7.570255] [atbm_log]:apollo wifi : can't open /tmp/radio/atbm_set_rate_powe r.txt ---WLAN---send e[ 7.579998] [atbm_log]:enable sg vent connected_cloudnotok [ 7.588155] [atbm_log]:enable sg [ 7.596734] [atbm_log]:[atbm_wtd]:set wtd_probe = 1 [Debug] [setLedEvent:429] setLed[ 7.604196] usbcore: registered new interface driver atbm_wlan [ 7.610812] [atbm_log]:[wtd] register. Event = 5 [Debug] [main:577] gLastLedEvent = 4, gCurrLedEvent = 5 [ 7.689967] wlan-manager: start sta... [ 7.693960] wlan-manager: ifconfig wlan0 up. [ 7.721736] br-wan: port 2(wlan0) entered blocking state [ 7.727007] br-wan: port 2(wlan0) entered disabled state [ 7.732713] device wlan0 entered promiscuous mode [ 7.737310] br-wan: port 2(wlan0) entered blocking state [ 7.742613] br-wan: port 2(wlan0) entered forwarding state [ 7.799122] i=0, setGain=-6 country=1 [ 7.837950] i=1, setGain=-6 country=1 [ 7.860212] i=2, setGain=2 country=1 [ 7.882570] i=3, setGain=2 country=1 [ 7.904835] i=4, setGain=2 country=1 [ 7.926866] i=5, setGain=2 country=1 [ 7.949163] i=6, setGain=2 country=1 [ 7.971443] i=7, setGain=0 country=1 [ 7.994091] i=8, setGain=-2 country=1 [ 8.016358] i=9, setGain=-2 country=1 [ 8.038607] i=10, setGain=0 country=1 cat: can't open '/sys/class/net/eth1/carrier': No such file or directory AC-15-A2-42-2B-19 [ 9.417726] [atbm_log]:ieee80211_check_country_limit_scan_2_4G_chan : scan_n_ channals = 14 ++++++++ [ 9.434751] [atbm_log]:ieee80211_check_country_limit_scan_2_4G_chan : scan_n_ channals = 13 --------- [ 9.451996] [atbm_log]:probereq[ff:ff:ff:ff:ff:ff][ac:15:a2:42:2b:19][ff:ff:f f:ff:ff:ff] [ 9.794447] start write config partition...partition_offset is 0x40000,addrSt art is 0x40000 [ 9.991276] ..done [ 10.309233] [atbm_log]:wlan0:free authen bss ++ [ 10.341880] [atbm_log]:wlan0:free authen bss ++ [ 10.402038] br-wan: port 2(wlan0) entered disabled state ---WLAN---send event connected_cloudnotok [Debug] [setLedEvent:429] setLedEvent = 5 [Debug] [main:577] gLastLedEvent = 5, gCurrLedEvent = 5 [Debug] [main:617] The event is the same, don't do everything generate key: 3600days 2048bits service: file '/usr/sbin/uhttpd' is not executable [2022-08-30 21:24:06][MAJOR][cloudiot]iot_base.c:182(run_once)-- cloud-iot start , pid: [1040] [2022-08-30 21:24:06][ERROR][cloudiot]cloud_iot_config.c:174(getDevInfoByUci)-- parse option failed [2022-08-30 21:24:06][ERROR][cloudiot]cloud_iot_config.c:216(getDeviceInfo)-- ge t device info by uci failed! [2022-08-30 21:24:06][ERROR][cloudiot]cloud_iot_config.c:438(cloud_iot_config_lo ad)-- get device's basic info failed! [2022-08-30 21:24:06][ERROR][cloudiot]socket_fd.c:1178(socket_fd_create)-- socke t dns resolve name: failed. [2022-08-30 21:24:06][ERROR][cloudiot]http_client.c:327(http_client_create)-- cl oud iot connect failed. [2022-08-30 21:24:06][ERROR][cloudiot]cloud_iot.c:408(cloud_http_send_request)-- create http ctx failed [2022-08-30 21:24:06][ERROR][cloudiot]cloud_iot.c:220(jwt_timer_handler)-- send http request failed [2022-08-30 21:24:06][ERROR][cloud-service] read_value_from_uci_option(366): err or: failed to get cloud_config:bind:bindCode. [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(644): dev_type: S MART.IPCAMERA [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(645): dev_model: C110 [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(646): dev_alias: П омещения. Ателье [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(649): dev_mac: [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(651): zoneid: A sia/Vladivostok [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(652): dev_name: C 110 [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(653): hw_ver: 1 .0 [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(654): fw_ver: 1 .3.0 Build 220830 Rel.69880n(4555) [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(656): oem_id: [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(659): device_bind_st atus: 1 [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(660): msg_push_switc h: 1 [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(662): bindCode: [2022-08-30 21:24:06][INFO][cloud-service] init_config_info(663): deviceSecret: [2022-08-30 21:24:06][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2022-08-30 21:24:06][ERROR][cloud-service] validate_token_thread(356): ubus_pro cess_validate: waiting 10 seconds and trying 1 times. MiniOS Version is 20210122 service: file '/usr/sbin/uhttpd' is not executable /etc/rc.common: eval: line 1: /usr/sbin/uhttpd: not found [2023-10-26 16:20:58][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:20:58][ERROR][cloud-service] validate_token_thread(356): ubus_pro cess_validate: waiting 20 seconds and trying 2 times. auto cloud recovery just check ip from ping printlines checking bing.com ... for 0st time OK internet already connected to get up.bin from cloud server just check ip from ping printlines checking bing.com ... for 0st time OK waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... [2023-10-26 16:21:18][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:21:18][ERROR][cloud-service] validate_token_thread(356): ubus_process_validate: waiting 40 seconds and trying 3 times. waiting for cloud to connect... [2023-10-26 16:21:19][ERROR][cloudiot]socket_fd.c:1178(socket_fd_create)-- socket dns resolve name: failed. [2023-10-26 16:21:19][ERROR][cloudiot]http_client.c:327(http_client_create)-- cloud iot connect failed. [2023-10-26 16:21:19][ERROR][cloudiot]cloud_iot.c:408(cloud_http_send_request)-- create http ctx failed [2023-10-26 16:21:19][ERROR][cloudiot]cloud_iot.c:220(jwt_timer_handler)-- send http request failed waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... [2023-10-26 16:21:58][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:21:58][ERROR][cloud-service] validate_token_thread(356): ubus_process_validate: waiting 64 seconds and trying 4 times. MiniOS will not enter softAP mode for non-factory-recover-mode but try again later will try again after 39 second [2023-10-26 16:22:21][ERROR][cloudiot]socket_fd.c:1178(socket_fd_create)-- socket dns resolve name: failed. [2023-10-26 16:22:21][ERROR][cloudiot]http_client.c:327(http_client_create)-- cloud iot connect failed. [2023-10-26 16:22:21][ERROR][cloudiot]cloud_iot.c:408(cloud_http_send_request)-- create http ctx failed [2023-10-26 16:22:21][ERROR][cloudiot]cloud_iot.c:220(jwt_timer_handler)-- send http request failed will try again after 1 second MiniOS Version is 20210122 [2023-10-26 16:23:02][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:23:02][ERROR][cloud-service] validate_token_thread(356): ubus_process_validate: waiting 64 seconds and trying 5 times. auto cloud recovery just check ip from ping printlines checking bing.com ... for 0st time OK internet already connected to get up.bin from cloud server just check ip from ping printlines checking bing.com ... for 0st time OK waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... [2023-10-26 16:24:06][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:24:06][ERROR][cloud-service] validate_token_thread(356): ubus_process_validate: waiting 64 seconds and trying 6 times. MiniOS will not enter softAP mode for non-factory-recover-mode but try again later will try again after 59 second [ 219.248990] random: crng init done will try again after 46 second [2023-10-26 16:24:25][ERROR][cloudiot]socket_fd.c:1178(socket_fd_create)-- socket dns resolve name: failed. [2023-10-26 16:24:25][ERROR][cloudiot]http_client.c:327(http_client_create)-- cloud iot connect failed. [2023-10-26 16:24:25][ERROR][cloudiot]cloud_iot.c:408(cloud_http_send_request)-- create http ctx failed [2023-10-26 16:24:25][ERROR][cloudiot]cloud_iot.c:220(jwt_timer_handler)-- send http request failed will try again after 1 second MiniOS Version is 20210122 [2023-10-26 16:25:10][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:25:10][ERROR][cloud-service] validate_token_thread(356): ubus_process_validate: waiting 64 seconds and trying 7 times. auto cloud recovery just check ip from ping printlines checking bing.com ... for 0st time OK internet already connected to get up.bin from cloud server just check ip from ping printlines checking bing.com ... for 0st time OK waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... ^C Please press Enter to activate this console. waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... [2023-10-26 16:26:14][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:26:14][ERROR][cloud-service] validate_token_thread(356): ubus_process_validate: waiting 64 seconds and trying 8 times. waiting for cloud to connect... MiniOS will not enter softAP mode for non-factory-recover-mode but try again later will try again after 4 second [2023-10-26 16:27:18][ERROR][cloudiot]ubus.c:101(get_validate_token)-- mqtt not establish, get validate deviceToken failed. [2023-10-26 16:27:18][ERROR][cloud-service] validate_token_thread(356): ubus_process_validate: waiting 64 seconds and trying 9 times. will try again after 1 second MiniOS Version is 20210122 auto cloud recovery just check ip from ping printlines checking bing.com ... for 0st time OK internet already connected to get up.bin from cloud server just check ip from ping printlines checking bing.com ... for 0st time OK waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect... waiting for cloud to connect...