diff --git a/README.rst b/README.rst index 12f59186..690a13e9 100644 --- a/README.rst +++ b/README.rst @@ -24,7 +24,7 @@ How to use it? -------------- #. Unzip the image and install it to an sd card `like any other Raspberry Pi image `_ -#. Configure your WiFi by editing ``octopi-network.txt`` on the root of the flashed card when using it like a thumb drive +#. Configure your WiFi by editing ``octopi-wifi.txt`` on the root of the flashed card when using it like a thumb drive #. Boot the Pi from the card #. Log into your Pi via SSH (it is located at ``octopi.local`` `if your computer supports bonjour `_ or the IP address assigned by your router), default username is "pi", default password is "raspberry", change the password using the ``passwd`` command and expand the filesystem of the SD card through the corresponding option when running ``sudo raspi-config``. diff --git a/src/filesystem/boot/octopi-ethernet.txt b/src/filesystem/boot/octopi-ethernet.txt new file mode 100644 index 00000000..2dcaac27 --- /dev/null +++ b/src/filesystem/boot/octopi-ethernet.txt @@ -0,0 +1,28 @@ +# You can use this file to manually set up your ethernet network configuration. + +### WIRED CONFIGURATION ##################################################### +# The following segment allows you to configure your wired connection +# with a static IP. +# +# Just uncomment the lines prefixed with a single #. Then connect +# a cable to the Pi and another system, e.g. a Laptop, and set that +# other system's network configuration to: +# +# address: 192.168.250.10 +# netmask: 255.255.255.0 +# broadcast: 192.168.250.255 +# +# You can then reach the Pi from the system's browser by going to +# +# http://192.168.250.1 +# +# or +# +# http://octopi.local + +#auto eth0:1 +#iface eth0:1 inet static +# address 192.168.250.1 +# netmask 255.255.255.0 +# broadcast 192.168.250.255 + diff --git a/src/filesystem/boot/octopi-network.txt b/src/filesystem/boot/octopi-network.txt deleted file mode 100644 index 17343a35..00000000 --- a/src/filesystem/boot/octopi-network.txt +++ /dev/null @@ -1,53 +0,0 @@ -# You can use this file to manually set up your network configuration. -# -# This file is included into /etc/network/interfaces, so anything that -# works by editing that file is also possible here. - -### WIFI CONFIGURATION ###################################################### -# The three segments below should cover you in most cases if you run -# a wifi network that uses either WPA/WPA2 or WEP encryption. -# -# Just uncomment the lines prefixed with a single # of the configuration -# that matches your wifi setup and fill in SSID and passphrase. - -## WPA/WPA2 secured -#iface wlan0-octopi inet manual -# wpa-ssid "put SSID here" -# wpa-psk "put password here" - -## WEP secured -#iface wlan0-octopi inet manual -# wireless-essid "put SSID here" -# wireless-key "put password here" - -## Open/unsecured -#iface wlan0-octopi inet manual -# wireless-essid "put SSID here" -# wireless-mode managed - -### WIRED CONFIGURATION ##################################################### -# The following segment allows you to configure your wired connection -# with a static IP. -# -# Just uncomment the lines prefixed with a single #. Then connect -# a cable to the Pi and another system, e.g. a Laptop, and set that -# other system's network configuration to: -# -# address: 192.168.250.10 -# netmask: 255.255.255.0 -# broadcast: 192.168.250.255 -# -# You can then reach the Pi from the system's browser by going to -# -# http://192.168.250.1 -# -# or -# -# http://octopi.local - -#auto eth0:1 -#iface eth0:1 inet static -# address 192.168.250.1 -# netmask 255.255.255.0 -# broadcast 192.168.250.255 -