diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 40f8b06ba7be..84172cb2c05d 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -399,70 +399,92 @@
// @section temperature
/**
- * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ * --NORMAL IS 4.7kΩ PULLUP!-- 1kΩ pullup can be used on hotend sensor, using correct resistor and table
*
* Temperature sensors available:
*
- * -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
- * -3 : thermocouple with MAX31855 (only for sensors 0-1)
- * -2 : thermocouple with MAX6675 (only for sensors 0-1)
- * -4 : thermocouple with AD8495
- * -1 : thermocouple with AD595
+ * SPI RTD/Thermocouple Boards - IMPORTANT: Read the NOTE below!
+ * -------
+ * -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
+ * NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
+ * -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
+ * -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
+ *
+ * NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
+ * Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
+ * Software SPI will be used on those ports instead. You can force Hardware SPI on the default bus in the
+ * Configuration_adv.h file. At this time, separate Hardware SPI buses for sensors are not supported.
+ *
+ * Analog Themocouple Boards
+ * -------
+ * -4 : AD8495 with Thermocouple
+ * -1 : AD595 with Thermocouple
+ *
+ * Analog Thermistors - 4.7kΩ pullup - Normal
+ * -------
+ * 1 : 100kΩ EPCOS - Best choice for EPCOS thermistors
+ * 331 : 100kΩ Same as #1, but 3.3V scaled for MEGA
+ * 332 : 100kΩ Same as #1, but 3.3V scaled for DUE
+ * 2 : 200kΩ ATC Semitec 204GT-2
+ * 202 : 200kΩ Copymaster 3D
+ * 3 : ???Ω Mendel-parts thermistor
+ * 4 : 10kΩ Generic Thermistor !! DO NOT use for a hotend - it gives bad resolution at high temp. !!
+ * 5 : 100kΩ ATC Semitec 104GT-2/104NT-4-R025H42G - Used in ParCan, J-Head, and E3D, SliceEngineering 300°C
+ * 501 : 100kΩ Zonestar - Tronxy X3A
+ * 502 : 100kΩ Zonestar - used by hot bed in Zonestar Průša P802M
+ * 512 : 100kΩ RPW-Ultra hotend
+ * 6 : 100kΩ EPCOS - Not as accurate as table #1 (created using a fluke thermocouple)
+ * 7 : 100kΩ Honeywell 135-104LAG-J01
+ * 71 : 100kΩ Honeywell 135-104LAF-J01
+ * 8 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT
+ * 9 : 100kΩ GE Sensing AL03006-58.2K-97-G1
+ * 10 : 100kΩ RS PRO 198-961
+ * 11 : 100kΩ Keenovo AC silicone mats, most Wanhao i3 machines - beta 3950, 1%
+ * 12 : 100kΩ Vishay 0603 SMD NTCS0603E3104FXT (#8) - calibrated for Makibox hot bed
+ * 13 : 100kΩ Hisens up to 300°C - for "Simple ONE" & "All In ONE" hotend - beta 3950, 1%
+ * 15 : 100kΩ Calibrated for JGAurora A5 hotend
+ * 18 : 200kΩ ATC Semitec 204GT-2 Dagoma.Fr - MKS_Base_DKU001327
+ * 22 : 100kΩ GTM32 Pro vB - hotend - 4.7kΩ pullup to 3.3V and 220Ω to analog input
+ * 23 : 100kΩ GTM32 Pro vB - bed - 4.7kΩ pullup to 3.3v and 220Ω to analog input
+ * 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
+ * 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950
+ * 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950
+ * 66 : 4.7MΩ Dyze Design High Temperature Thermistor
+ * 67 : 500kΩ SliceEngineering 450°C Thermistor
+ * 70 : 100kΩ bq Hephestos 2
+ * 75 : 100kΩ Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
+ *
+ * Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
+ * ------- (but gives greater accuracy and more stable PID)
+ * 51 : 100kΩ EPCOS (1kΩ pullup)
+ * 52 : 200kΩ ATC Semitec 204GT-2 (1kΩ pullup)
+ * 55 : 100kΩ ATC Semitec 104GT-2 - Used in ParCan & J-Head (1kΩ pullup)
+ *
+ * Analog Thermistors - 10kΩ pullup - Atypical
+ * -------
+ * 99 : 100kΩ Found on some Wanhao i3 machines with a 10kΩ pull-up resistor
+ *
+ * Analog RTDs (Pt100/Pt1000)
+ * -------
+ * 110 : Pt100 with 1kΩ pullup (atypical)
+ * 147 : Pt100 with 4.7kΩ pullup
+ * 1010 : Pt1000 with 1kΩ pullup (atypical)
+ * 1047 : Pt1000 with 4.7kΩ pullup (E3D)
+ * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
+ * NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
+ * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
+ * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
+ * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
+ *
+ * Custom/Dummy/Other Thermos
+ * ------
* 0 : not used
- * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
- * 331 : (3.3V scaled thermistor 1 table for MEGA)
- * 332 : (3.3V scaled thermistor 1 table for DUE)
- * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
- * 202 : 200k thermistor - Copymaster 3D
- * 3 : Mendel-parts thermistor (4.7k pullup)
- * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
- * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan, J-Head, and E3D) (4.7k pullup)
- * 501 : 100K Zonestar (Tronxy X3A) Thermistor
- * 502 : 100K Zonestar Thermistor used by hot bed in Zonestar Průša P802M
- * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
- * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
- * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
- * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
- * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
- * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
- * 10 : 100k RS thermistor 198-961 (4.7k pullup)
- * 11 : 100k beta 3950 1% thermistor (Used in Keenovo AC silicone mats and most Wanhao i3 machines) (4.7k pullup)
- * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
- * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
- * 15 : 100k thermistor calibration for JGAurora A5 hotend
- * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
- * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
- * NOTES: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
- * 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v ADC reference voltage (STM32, LPC176x....) and 5V INA826 amplifier board supply.
- * NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
- * 22 : 100k (hotend) with 4.7k pullup to 3.3V and 220R to analog input (as in GTM32 Pro vB)
- * 23 : 100k (bed) with 4.7k pullup to 3.3v and 220R to analog input (as in GTM32 Pro vB)
- * 30 : Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K / B3950 (4.7k pullup)
- * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
- * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
- * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
- * 66 : 4.7M High Temperature thermistor from Dyze Design
- * 67 : 450C thermistor from SliceEngineering
- * 70 : the 100K thermistor found in the bq Hephestos 2
- * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
- * 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)
- *
- * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
- * (but gives greater accuracy and more stable PID)
- * 51 : 100k thermistor - EPCOS (1k pullup)
- * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
- * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
- *
- * 1047 : Pt1000 with 4k7 pullup (E3D)
- * 1010 : Pt1000 with 1k pullup (non standard)
- * 147 : Pt100 with 4k7 pullup
- * 110 : Pt100 with 1k pullup (non standard)
- *
* 1000 : Custom - Specify parameters in Configuration_adv.h
*
- * Use these for Testing or Development purposes. NEVER for production machine.
+ * !!! Use these for Testing or Development purposes. NEVER for production machine. !!!
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
*/
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 0
@@ -484,7 +506,7 @@
// Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
//#define MAX31865_SENSOR_OHMS_0 100 // (Ω) Typically 100 or 1000 (PT100 or PT1000)
-//#define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for AdaFruit PT100; 4300 for AdaFruit PT1000
+//#define MAX31865_CALIBRATION_OHMS_0 430 // (Ω) Typically 430 for Adafruit PT100; 4300 for Adafruit PT1000
//#define MAX31865_SENSOR_OHMS_1 100
//#define MAX31865_CALIBRATION_OHMS_1 430
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index c1cddae8d16c..bd8e2ab4c92e 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -133,10 +133,21 @@
#define REDUNDANT_BETA 3950 // Beta value
#endif
-//
-// Hephestos 2 24V heated bed upgrade kit.
-// https://store.bq.com/en/heated-bed-kit-hephestos2
-//
+/**
+ * Configuration options for MAX Thermocouples (-2, -3, -5).
+ * FORCE_HW_SPI: Ignore SCK/MOSI/MISO pins and just use the CS pin & default SPI bus.
+ * MAX31865_WIRES: Set the number of wires for the probe connected to a MAX31865 board, 2-4. Default: 2
+ * MAX31865_50HZ: Enable 50Hz filter instead of the default 60Hz.
+ */
+//#define TEMP_SENSOR_FORCE_HW_SPI
+//#define MAX31865_SENSOR_WIRES_0 2
+//#define MAX31865_SENSOR_WIRES_1 2
+//#define MAX31865_50HZ_FILTER
+
+/**
+ * Hephestos 2 24V heated bed upgrade kit.
+ * https://store.bq.com/en/heated-bed-kit-hephestos2
+ */
//#define HEPHESTOS2_HEATED_BED_KIT
#if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
#undef TEMP_SENSOR_BED
diff --git a/Marlin/src/HAL/SAMD51/inc/SanityCheck.h b/Marlin/src/HAL/SAMD51/inc/SanityCheck.h
index 2a4bde98e6cb..38c6dd9e08de 100644
--- a/Marlin/src/HAL/SAMD51/inc/SanityCheck.h
+++ b/Marlin/src/HAL/SAMD51/inc/SanityCheck.h
@@ -31,7 +31,8 @@
#error "No custom SD drive cable defined for this board."
#endif
-#if defined(MAX6675_SCK_PIN) && defined(MAX6675_DO_PIN) && (MAX6675_SCK_PIN == SCK1 || MAX6675_DO_PIN == MISO1)
+#if (defined(TEMP_0_SCK_PIN) && defined(TEMP_0_MISO_PIN) && (TEMP_0_SCK_PIN == SCK1 || TEMP_0_MISO_PIN == MISO1)) || \
+ (defined(TEMP_1_SCK_PIN) && defined(TEMP_1_MISO_PIN) && (TEMP_1_SCK_PIN == SCK1 || TEMP_1_MISO_PIN == MISO1))
#error "OnBoard SPI BUS can't be shared with other devices."
#endif
diff --git a/Marlin/src/MarlinCore.cpp b/Marlin/src/MarlinCore.cpp
index 254283da5b67..dc9fbb2ba787 100644
--- a/Marlin/src/MarlinCore.cpp
+++ b/Marlin/src/MarlinCore.cpp
@@ -1169,10 +1169,10 @@ void setup() {
// Init and disable SPI thermocouples; this is still needed
#if TEMP_SENSOR_0_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 0)
- OUT_WRITE(MAX6675_SS_PIN, HIGH); // Disable
+ OUT_WRITE(TEMP_0_CS_PIN, HIGH); // Disable
#endif
#if TEMP_SENSOR_1_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
- OUT_WRITE(MAX6675_SS2_PIN, HIGH); // Disable
+ OUT_WRITE(TEMP_1_CS_PIN, HIGH);
#endif
#if ENABLED(DUET_SMART_EFFECTOR) && PIN_EXISTS(SMART_EFFECTOR_MOD)
diff --git a/Marlin/src/core/macros.h b/Marlin/src/core/macros.h
index 295eee9bcfa8..05640bce8740 100644
--- a/Marlin/src/core/macros.h
+++ b/Marlin/src/core/macros.h
@@ -204,8 +204,8 @@
#define __TERN(T,V...) ___TERN(_CAT(_NO,T),V) // Prepend '_NO' to get '_NOT_0' or '_NOT_1'
#define ___TERN(P,V...) THIRD(P,V) // If first argument has a comma, A. Else B.
-#define _OPTARG(A) , A
-#define OPTARG(O,A) TERN_(O,DEFER4(_OPTARG)(A))
+#define _OPTARG(A...) , A
+#define OPTARG(O,A...) TERN_(O,DEFER4(_OPTARG)(A))
#define _OPTCODE(A) A;
#define OPTCODE(O,A) TERN_(O,DEFER4(_OPTCODE)(A))
diff --git a/Marlin/src/gcode/calibrate/G34_M422.cpp b/Marlin/src/gcode/calibrate/G34_M422.cpp
index 686996202840..50f3419c8960 100644
--- a/Marlin/src/gcode/calibrate/G34_M422.cpp
+++ b/Marlin/src/gcode/calibrate/G34_M422.cpp
@@ -314,11 +314,13 @@ void GcodeSuite::G34() {
sprintf_P(msg,
PSTR("1:2=%s" TERN_(TRIPLE_Z, " 3-2=%s 3-1=%s") TERN_(QUAD_Z, " 4-3=%s 4-2=%s 4-1=%s")),
dtostrf(ABS(z_measured[1] - z_measured[0]), 1, 3, fstr1)
- OPTARG(TRIPLE_Z, dtostrf(ABS(z_measured[2] - z_measured[1]), 1, 3, fstr2))
- OPTARG(TRIPLE_Z, dtostrf(ABS(z_measured[2] - z_measured[0]), 1, 3, fstr3))
- OPTARG(QUAD_Z, dtostrf(ABS(z_measured[3] - z_measured[2]), 1, 3, fstr4))
- OPTARG(QUAD_Z, dtostrf(ABS(z_measured[3] - z_measured[1]), 1, 3, fstr5))
- OPTARG(QUAD_Z, dtostrf(ABS(z_measured[3] - z_measured[0]), 1, 3, fstr6))
+ OPTARG(TRIPLE_Z,
+ dtostrf(ABS(z_measured[2] - z_measured[1]), 1, 3, fstr2),
+ dtostrf(ABS(z_measured[2] - z_measured[0]), 1, 3, fstr3))
+ OPTARG(QUAD_Z,
+ dtostrf(ABS(z_measured[3] - z_measured[2]), 1, 3, fstr4),
+ dtostrf(ABS(z_measured[3] - z_measured[1]), 1, 3, fstr5),
+ dtostrf(ABS(z_measured[3] - z_measured[0]), 1, 3, fstr6))
);
ui.set_status(msg);
#endif
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index 45271bca72ac..2f5af2b7008e 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -615,20 +615,21 @@
#if TEMP_SENSOR_0 == -5 || TEMP_SENSOR_0 == -3 || TEMP_SENSOR_0 == -2
#define TEMP_SENSOR_0_IS_MAX_TC 1
- #define HAS_MAX_TC 1
- #if TEMP_SENSOR_0 == -3
- #define TEMP_SENSOR_0_MAX_TC_TMIN -270
- #define TEMP_SENSOR_0_MAX_TC_TMAX 1800
- #else
- #define TEMP_SENSOR_0_MAX_TC_TMIN 0
- #define TEMP_SENSOR_0_MAX_TC_TMAX 1024
- #endif
#if TEMP_SENSOR_0 == -5
#define TEMP_SENSOR_0_IS_MAX31865 1
+ #define TEMP_SENSOR_0_MAX_TC_TMIN 0
+ #define TEMP_SENSOR_0_MAX_TC_TMAX 1024
+ #ifndef MAX31865_SENSOR_WIRES_0
+ #define MAX31865_SENSOR_WIRES_0 2
+ #endif
#elif TEMP_SENSOR_0 == -3
#define TEMP_SENSOR_0_IS_MAX31855 1
+ #define TEMP_SENSOR_0_MAX_TC_TMIN -270
+ #define TEMP_SENSOR_0_MAX_TC_TMAX 1800
#elif TEMP_SENSOR_0 == -2
#define TEMP_SENSOR_0_IS_MAX6675 1
+ #define TEMP_SENSOR_0_MAX_TC_TMIN 0
+ #define TEMP_SENSOR_0_MAX_TC_TMAX 1024
#endif
#elif TEMP_SENSOR_0 == -4
#define TEMP_SENSOR_0_IS_AD8495 1
@@ -648,21 +649,23 @@
#if TEMP_SENSOR_1 == -5 || TEMP_SENSOR_1 == -3 || TEMP_SENSOR_1 == -2
#define TEMP_SENSOR_1_IS_MAX_TC 1
- #define HAS_MAX_TC 1
- #if TEMP_SENSOR_1 == -3
- #define TEMP_SENSOR_1_MAX_TC_TMIN -270
- #define TEMP_SENSOR_1_MAX_TC_TMAX 1800
- #else
- #define TEMP_SENSOR_1_MAX_TC_TMIN 0
- #define TEMP_SENSOR_1_MAX_TC_TMAX 1024
- #endif
#if TEMP_SENSOR_1 == -5
#define TEMP_SENSOR_1_IS_MAX31865 1
+ #define TEMP_SENSOR_1_MAX_TC_TMIN 0
+ #define TEMP_SENSOR_1_MAX_TC_TMAX 1024
+ #ifndef MAX31865_SENSOR_WIRES_1
+ #define MAX31865_SENSOR_WIRES_1 2
+ #endif
#elif TEMP_SENSOR_1 == -3
#define TEMP_SENSOR_1_IS_MAX31855 1
+ #define TEMP_SENSOR_1_MAX_TC_TMIN -270
+ #define TEMP_SENSOR_1_MAX_TC_TMAX 1800
#elif TEMP_SENSOR_1 == -2
#define TEMP_SENSOR_1_IS_MAX6675 1
+ #define TEMP_SENSOR_1_MAX_TC_TMIN 0
+ #define TEMP_SENSOR_1_MAX_TC_TMAX 1024
#endif
+
#if TEMP_SENSOR_1 != TEMP_SENSOR_0
#if TEMP_SENSOR_1 == -5
#error "If MAX31865 Thermocouple (-5) is used for TEMP_SENSOR_1 then TEMP_SENSOR_0 must match."
@@ -690,37 +693,48 @@
#if TEMP_SENSOR_REDUNDANT == -5 || TEMP_SENSOR_REDUNDANT == -3 || TEMP_SENSOR_REDUNDANT == -2
#define TEMP_SENSOR_REDUNDANT_IS_MAX_TC 1
- #define HAS_MAX_TC 1
- #if TEMP_SENSOR_REDUNDANT == -3
- #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN -270
- #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX 1800
- #else
- #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN 0
- #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX 1024
- #endif
- #if TEMP_SENSOR_REDUNDANT_SOURCE == 0
- #define TEMP_SENSOR_0_MAX_TC_TMIN TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN
- #define TEMP_SENSOR_0_MAX_TC_TMAX TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX
- #elif TEMP_SENSOR_REDUNDANT_SOURCE == 1
- #define TEMP_SENSOR_1_MAX_TC_TMIN TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN
- #define TEMP_SENSOR_1_MAX_TC_TMAX TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX
- #endif
+
#if TEMP_SENSOR_REDUNDANT == -5
#if TEMP_SENSOR_REDUNDANT_SOURCE != 0 && TEMP_SENSOR_REDUNDANT_SOURCE != 1
#error "MAX31865 Thermocouples (-5) not supported for TEMP_SENSOR_REDUNDANT_SOURCE other than TEMP_SENSOR_0/TEMP_SENSOR_1 (0/1)."
#endif
- #define TEMP_SENSOR_REDUNDANT_IS_MAX31865 1
+
+ #define TEMP_SENSOR_REDUNDANT_IS_MAX31865 1
+ #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN 0
+ #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX 1024
#elif TEMP_SENSOR_REDUNDANT == -3
#if TEMP_SENSOR_REDUNDANT_SOURCE != 0 && TEMP_SENSOR_REDUNDANT_SOURCE != 1
#error "MAX31855 Thermocouples (-3) not supported for TEMP_SENSOR_REDUNDANT_SOURCE other than TEMP_SENSOR_0/TEMP_SENSOR_1 (0/1)."
#endif
- #define TEMP_SENSOR_REDUNDANT_IS_MAX31855 1
+
+ #define TEMP_SENSOR_REDUNDANT_IS_MAX31855 1
+ #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN -270
+ #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX 1800
#elif TEMP_SENSOR_REDUNDANT == -2
#if TEMP_SENSOR_REDUNDANT_SOURCE != 0 && TEMP_SENSOR_REDUNDANT_SOURCE != 1
#error "MAX6675 Thermocouples (-2) not supported for TEMP_SENSOR_REDUNDANT_SOURCE other than TEMP_SENSOR_0/TEMP_SENSOR_1 (0/1)."
#endif
- #define TEMP_SENSOR_REDUNDANT_IS_MAX6675 1
+
+ #define TEMP_SENSOR_REDUNDANT_IS_MAX6675 1
+ #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN 0
+ #define TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX 1024
#endif
+
+ // mimic setting up the source TEMP_SENSOR
+ #if TEMP_SENSOR_REDUNDANT_SOURCE == 0
+ #define TEMP_SENSOR_0_MAX_TC_TMIN TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN
+ #define TEMP_SENSOR_0_MAX_TC_TMAX TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX
+ #ifndef MAX31865_SENSOR_WIRES_0
+ #define MAX31865_SENSOR_WIRES_0 2
+ #endif
+ #elif TEMP_SENSOR_REDUNDANT_SOURCE == 1
+ #define TEMP_SENSOR_1_MAX_TC_TMIN TEMP_SENSOR_REDUNDANT_MAX_TC_TMIN
+ #define TEMP_SENSOR_1_MAX_TC_TMAX TEMP_SENSOR_REDUNDANT_MAX_TC_TMAX
+ #ifndef MAX31865_SENSOR_WIRES_1
+ #define MAX31865_SENSOR_WIRES_1 2
+ #endif
+ #endif
+
#if (TEMP_SENSOR_0_IS_MAX_TC && TEMP_SENSOR_REDUNDANT != TEMP_SENSOR_0) || (TEMP_SENSOR_1_IS_MAX_TC && TEMP_SENSOR_REDUNDANT != TEMP_SENSOR_1)
#if TEMP_SENSOR_REDUNDANT == -5
#error "If MAX31865 Thermocouple (-5) is used for TEMP_SENSOR_0/TEMP_SENSOR_1 then TEMP_SENSOR_REDUNDANT must match."
@@ -743,101 +757,182 @@
#endif
#endif
+#if TEMP_SENSOR_0_IS_MAX_TC || TEMP_SENSOR_1_IS_MAX_TC || TEMP_SENSOR_REDUNDANT_IS_MAX_TC
+ #define HAS_MAX_TC 1
+#endif
+#if TEMP_SENSOR_0_IS_MAX6675 || TEMP_SENSOR_1_IS_MAX6675 || TEMP_SENSOR_REDUNDANT_IS_MAX6675
+ #define HAS_MAX6675 1
+#endif
#if TEMP_SENSOR_0_IS_MAX31855 || TEMP_SENSOR_1_IS_MAX31855 || TEMP_SENSOR_REDUNDANT_IS_MAX31855
#define HAS_MAX31855 1
#endif
#if TEMP_SENSOR_0_IS_MAX31865 || TEMP_SENSOR_1_IS_MAX31865 || TEMP_SENSOR_REDUNDANT_IS_MAX31865
#define HAS_MAX31865 1
#endif
-#if TEMP_SENSOR_0_IS_MAX6675 || TEMP_SENSOR_1_IS_MAX6675 || TEMP_SENSOR_REDUNDANT_IS_MAX6675
- #define HAS_MAX6675 1
-#endif
//
// Compatibility layer for MAX (SPI) temp boards
//
-#define TEMP_SENSOR_IS_MAX(n, M) (ENABLED(TEMP_SENSOR_##n##_IS_##M) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_##M) && TEMP_SENSOR_REDUNDANT_SOURCE == (n)))
+#if HAS_MAX_TC
+
+ // Translate old _SS, _CS, _SCK, _DO, _DI, _MISO, and _MOSI PIN defines.
+ #if TEMP_SENSOR_0_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
+
+ #if !PIN_EXISTS(TEMP_0_CS) // SS, CS
+ #if PIN_EXISTS(MAX6675_SS)
+ #define TEMP_0_CS_PIN MAX6675_SS_PIN
+ #elif PIN_EXISTS(MAX6675_CS)
+ #define TEMP_0_CS_PIN MAX6675_CS_PIN
+ #elif PIN_EXISTS(MAX31855_SS)
+ #define TEMP_0_CS_PIN MAX31855_SS_PIN
+ #elif PIN_EXISTS(MAX31855_CS)
+ #define TEMP_0_CS_PIN MAX31855_CS_PIN
+ #elif PIN_EXISTS(MAX31865_SS)
+ #define TEMP_0_CS_PIN MAX31865_SS_PIN
+ #elif PIN_EXISTS(MAX31865_CS)
+ #define TEMP_0_CS_PIN MAX31865_CS_PIN
+ #endif
+ #endif
-#if PIN_EXISTS(MAX6675_SS)
- #if TEMP_SENSOR_IS_MAX(0, MAX31855)
- #define MAX31855_CS_PIN MAX6675_SS_PIN
- #elif TEMP_SENSOR_IS_MAX(0, MAX31865)
- #define MAX31865_CS_PIN MAX6675_SS_PIN
- #elif TEMP_SENSOR_IS_MAX(0, MAX6675)
- #define MAX6675_CS_PIN MAX6675_SS_PIN
- #endif
-#endif
+ #if TEMP_SENSOR_0_IS_MAX6675
+ #if !PIN_EXISTS(TEMP_0_MISO) // DO
+ #if PIN_EXISTS(MAX6675_MISO)
+ #define TEMP_0_MISO_PIN MAX6675_MISO_PIN
+ #elif PIN_EXISTS(MAX6675_DO)
+ #define TEMP_0_MISO_PIN MAX6675_DO_PIN
+ #endif
+ #endif
+ #if !PIN_EXISTS(TEMP_0_SCK) && PIN_EXISTS(MAX6675_SCK)
+ #define TEMP_0_SCK_PIN MAX6675_SCK_PIN
+ #endif
-#if PIN_EXISTS(MAX6675_SS2)
- #if TEMP_SENSOR_IS_MAX(1, MAX31855)
- #define MAX31855_CS2_PIN MAX6675_SS2_PIN
- #elif TEMP_SENSOR_IS_MAX(1, MAX31865)
- #define MAX31865_CS2_PIN MAX6675_SS2_PIN
- #elif TEMP_SENSOR_IS_MAX(1, MAX6675)
- #define MAX6675_CS2_PIN MAX6675_SS2_PIN
- #endif
-#endif
+ #elif TEMP_SENSOR_0_IS_MAX31855
+ #if !PIN_EXISTS(TEMP_0_MISO) // DO
+ #if PIN_EXISTS(MAX31855_MISO)
+ #define TEMP_0_MISO_PIN MAX31855_MISO_PIN
+ #elif PIN_EXISTS(MAX31855_DO)
+ #define TEMP_0_MISO_PIN MAX31855_DO_PIN
+ #endif
+ #endif
+ #if !PIN_EXISTS(TEMP_0_SCK) && PIN_EXISTS(MAX31855_SCK)
+ #define TEMP_0_SCK_PIN MAX31855_SCK_PIN
+ #endif
-#if PIN_EXISTS(MAX6675_DO)
- #if HAS_MAX31855
- #define MAX31855_MISO_PIN MAX6675_DO_PIN
- #elif HAS_MAX31865
- #define MAX31865_MISO_PIN MAX6675_DO_PIN
- #elif HAS_MAX6675
- #define MAX6675_MISO_PIN MAX6675_DO_PIN
- #endif
-#endif
+ #elif TEMP_SENSOR_1_IS_MAX31865
+ #if !PIN_EXISTS(TEMP_1_MISO) // DO
+ #if PIN_EXISTS(MAX31865_MISO)
+ #define TEMP_1_MISO_PIN MAX31865_MISO_PIN
+ #elif PIN_EXISTS(MAX31865_DO)
+ #define TEMP_1_MISO_PIN MAX31865_DO_PIN
+ #endif
+ #endif
+ #if !PIN_EXISTS(TEMP_1_SCK) && PIN_EXISTS(MAX31865_SCK)
+ #define TEMP_1_SCK_PIN MAX31865_SCK_PIN
+ #endif
+ #if !PIN_EXISTS(TEMP_1_MOSI) && PIN_EXISTS(MAX31865_MOSI) // MOSI for '65 only
+ #define TEMP_1_MOSI_PIN MAX31865_MOSI_PIN
+ #endif
+ #endif
-#if PIN_EXISTS(MAX6675_SCK)
- #if HAS_MAX31855
- #define MAX31855_SCK_PIN MAX6675_SCK_PIN
- #elif HAS_MAX31865
- #define MAX31865_SCK_PIN MAX6675_SCK_PIN
- #endif
-#endif
+ // Software SPI - enable if MISO/SCK are defined.
+ #if PIN_EXISTS(TEMP_0_MISO) && PIN_EXISTS(TEMP_0_SCK) && DISABLED(TEMP_SENSOR_0_FORCE_HW_SPI)
+ #if TEMP_SENSOR_0_IS_MAX31865 && !PIN_EXISTS(TEMP_0_MOSI)
+ #error "TEMP_SENSOR_0 MAX31865 requires TEMP_0_MOSI_PIN defined for Software SPI. To use Hardware SPI instead, undefine MISO/SCK or enable TEMP_SENSOR_0_FORCE_HW_SPI."
+ #else
+ #define TEMP_SENSOR_0_HAS_SPI_PINS 1
+ #endif
+ #endif
-// Compatibility Layer for use when HAL manipulates PINS for MAX31855 and MAX6675
-#if PIN_EXISTS(MAX31855_CS) && !PIN_EXISTS(MAX6675_SS)
- #define MAX6675_SS_PIN MAX31855_CS_PIN
-#endif
-#if PIN_EXISTS(MAX31855_CS2) && !PIN_EXISTS(MAX6675_SS2)
- #define MAX6675_SS2_PIN MAX31855_CS2_PIN
-#endif
-#if PIN_EXISTS(MAX6675_CS) && !PIN_EXISTS(MAX6675_SS)
- #define MAX6675_SS_PIN MAX6675_CS_PIN
-#endif
-#if PIN_EXISTS(MAX6675_CS2) && !PIN_EXISTS(MAX6675_SS2)
- #define MAX6675_SS2_PIN MAX6675_CS2_PIN
-#endif
-#if PIN_EXISTS(MAX31855_MISO) && !PIN_EXISTS(MAX6675_DO)
- #define MAX6675_DO_PIN MAX31855_MISO_PIN
-#endif
-#if PIN_EXISTS(MAX6675_MISO) && !PIN_EXISTS(MAX6675_DO)
- #define MAX6675_DO_PIN MAX6675_MISO_PIN
-#endif
-#if PIN_EXISTS(MAX31855_SCK) && !PIN_EXISTS(MAX6675_SCK)
- #define MAX6675_SCK_PIN MAX31855_SCK_PIN
-#endif
+ #endif // TEMP_SENSOR_0_IS_MAX_TC
+
+ #if TEMP_SENSOR_1_IS_MAX_TC || (TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
+
+ #if !PIN_EXISTS(TEMP_1_CS) // SS2, CS2
+ #if PIN_EXISTS(MAX6675_SS2)
+ #define TEMP_1_CS_PIN MAX6675_SS2_PIN
+ #elif PIN_EXISTS(MAX6675_CS)
+ #define TEMP_1_CS_PIN MAX6675_CS2_PIN
+ #elif PIN_EXISTS(MAX31855_SS2)
+ #define TEMP_1_CS_PIN MAX31855_SS2_PIN
+ #elif PIN_EXISTS(MAX31855_CS2)
+ #define TEMP_1_CS_PIN MAX31855_CS2_PIN
+ #elif PIN_EXISTS(MAX31865_SS2)
+ #define TEMP_1_CS_PIN MAX31865_SS2_PIN
+ #elif PIN_EXISTS(MAX31865_CS2)
+ #define TEMP_1_CS_PIN MAX31865_CS2_PIN
+ #endif
+ #endif
-//
-// User-defined thermocouple libraries
-//
-// Add LIB_MAX6675 / LIB_MAX31855 / LIB_MAX31865 to the build_flags
-// to select a USER library for MAX6675, MAX31855, MAX31865
-//
-#if BOTH(HAS_MAX6675, LIB_MAX6675)
- #define LIB_USR_MAX6675 1
-#endif
-#if BOTH(HAS_MAX31855, LIB_MAX31855)
- #define LIB_USR_MAX31855 1
-#endif
-#if HAS_MAX31865
- #if ENABLED(LIB_MAX31865)
+ #if TEMP_SENSOR_1_IS_MAX6675
+ #if !PIN_EXISTS(TEMP_1_MISO) // DO
+ #if PIN_EXISTS(MAX6675_MISO)
+ #define TEMP_1_MISO_PIN MAX6675_MISO_PIN
+ #elif PIN_EXISTS(MAX6675_DO)
+ #define TEMP_1_MISO_PIN MAX6675_DO_PIN
+ #endif
+ #endif
+ #if !PIN_EXISTS(TEMP_1_SCK) && PIN_EXISTS(MAX6675_SCK)
+ #define TEMP_1_SCK_PIN MAX6675_SCK_PIN
+ #endif
+
+ #elif TEMP_SENSOR_1_IS_MAX31855
+ #if !PIN_EXISTS(TEMP_1_MISO) // DO
+ #if PIN_EXISTS(MAX31855_MISO)
+ #define TEMP_1_MISO_PIN MAX31855_MISO_PIN
+ #elif PIN_EXISTS(MAX31855_DO)
+ #define TEMP_1_MISO_PIN MAX31855_DO_PIN
+ #endif
+ #endif
+ #if !PIN_EXISTS(TEMP_1_SCK) && PIN_EXISTS(MAX31855_SCK)
+ #define TEMP_1_SCK_PIN MAX31855_SCK_PIN
+ #endif
+
+ #elif TEMP_SENSOR_1_IS_MAX31865
+ #if !PIN_EXISTS(TEMP_1_MISO) // DO
+ #if PIN_EXISTS(MAX31865_MISO)
+ #define TEMP_1_MISO_PIN MAX31865_MISO_PIN
+ #elif PIN_EXISTS(MAX31865_DO)
+ #define TEMP_1_MISO_PIN MAX31865_DO_PIN
+ #endif
+ #endif
+ #if !PIN_EXISTS(TEMP_1_SCK) && PIN_EXISTS(MAX31865_SCK)
+ #define TEMP_1_SCK_PIN MAX31865_SCK_PIN
+ #endif
+ #if !PIN_EXISTS(TEMP_1_MOSI) && PIN_EXISTS(MAX31865_MOSI) // MOSI for '65 only
+ #define TEMP_1_MOSI_PIN MAX31865_MOSI_PIN
+ #endif
+ #endif
+
+ // Software SPI - enable if MISO/SCK are defined.
+ #if PIN_EXISTS(TEMP_1_MISO) && PIN_EXISTS(TEMP_1_SCK) && DISABLED(TEMP_SENSOR_1_FORCE_HW_SPI)
+ #if TEMP_SENSOR_1_IS_MAX31865 && !PIN_EXISTS(TEMP_1_MOSI)
+ #error "TEMP_SENSOR_1 MAX31865 requires TEMP_1_MOSI_PIN defined for Software SPI. To use Hardware SPI instead, undefine MISO/SCK or enable TEMP_SENSOR_1_FORCE_HW_SPI."
+ #else
+ #define TEMP_SENSOR_1_HAS_SPI_PINS 1
+ #endif
+ #endif
+
+ #endif // TEMP_SENSOR_1_IS_MAX_TC
+
+ //
+ // User-defined thermocouple libraries
+ //
+ // Add LIB_MAX6675 / LIB_MAX31855 / LIB_MAX31865 to the build_flags
+ // to select a USER library for MAX6675, MAX31855, MAX31865
+ //
+ #if BOTH(HAS_MAX6675, LIB_MAX6675)
+ #define LIB_USR_MAX6675 1
+ #endif
+ #if BOTH(HAS_MAX31855, LIB_MAX31855)
+ #define LIB_USR_MAX31855 1
+ #endif
+ #if BOTH(HAS_MAX31865, LIB_MAX31865)
#define LIB_USR_MAX31865 1
- #else
- #define LIB_ADAFRUIT_MAX31865 1
+ #elif HAS_MAX31865
+ #define LIB_INTERNAL_MAX31865 1
#endif
-#endif
+
+#endif //HAS_MAX_TC
#if TEMP_SENSOR_2 == -4
#define TEMP_SENSOR_2_IS_AD8495 1
@@ -2722,6 +2817,77 @@
#define BED_OR_CHAMBER_OR_FAN 1
#endif
+/**
+ * Up to 3 PWM fans
+ */
+#ifndef FAN_INVERTING
+ #define FAN_INVERTING false
+#endif
+
+#if HAS_FAN7
+ #define FAN_COUNT 8
+#elif HAS_FAN6
+ #define FAN_COUNT 7
+#elif HAS_FAN5
+ #define FAN_COUNT 6
+#elif HAS_FAN4
+ #define FAN_COUNT 5
+#elif HAS_FAN3
+ #define FAN_COUNT 4
+#elif HAS_FAN2
+ #define FAN_COUNT 3
+#elif HAS_FAN1
+ #define FAN_COUNT 2
+#elif HAS_FAN0
+ #define FAN_COUNT 1
+#else
+ #define FAN_COUNT 0
+#endif
+
+#if FAN_COUNT > 0
+ #define HAS_FAN 1
+#endif
+
+/**
+ * Part Cooling fan multipliexer
+ */
+#if PIN_EXISTS(FANMUX0)
+ #define HAS_FANMUX 1
+#endif
+
+/**
+ * MIN/MAX fan PWM scaling
+ */
+#ifndef FAN_OFF_PWM
+ #define FAN_OFF_PWM 0
+#endif
+#ifndef FAN_MIN_PWM
+ #if FAN_OFF_PWM > 0
+ #define FAN_MIN_PWM (FAN_OFF_PWM + 1)
+ #else
+ #define FAN_MIN_PWM 0
+ #endif
+#endif
+#ifndef FAN_MAX_PWM
+ #define FAN_MAX_PWM 255
+#endif
+#if FAN_MIN_PWM < 0 || FAN_MIN_PWM > 255
+ #error "FAN_MIN_PWM must be a value from 0 to 255."
+#elif FAN_MAX_PWM < 0 || FAN_MAX_PWM > 255
+ #error "FAN_MAX_PWM must be a value from 0 to 255."
+#elif FAN_MIN_PWM > FAN_MAX_PWM
+ #error "FAN_MIN_PWM must be less than or equal to FAN_MAX_PWM."
+#elif FAN_OFF_PWM > FAN_MIN_PWM
+ #error "FAN_OFF_PWM must be less than or equal to FAN_MIN_PWM."
+#endif
+
+/**
+ * FAST PWM FAN Settings
+ */
+#if ENABLED(FAST_PWM_FAN) && !defined(FAST_PWM_FAN_FREQUENCY)
+ #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1)) // Fan frequency default
+#endif
+
// Servos
#if PIN_EXISTS(SERVO0) && NUM_SERVOS > 0
#define HAS_SERVO_0 1
@@ -2996,77 +3162,6 @@
#undef PREHEAT_SHORTCUT_MENU_ITEM
#endif
-/**
- * Up to 3 PWM fans
- */
-#ifndef FAN_INVERTING
- #define FAN_INVERTING false
-#endif
-
-#if HAS_FAN7
- #define FAN_COUNT 8
-#elif HAS_FAN6
- #define FAN_COUNT 7
-#elif HAS_FAN5
- #define FAN_COUNT 6
-#elif HAS_FAN4
- #define FAN_COUNT 5
-#elif HAS_FAN3
- #define FAN_COUNT 4
-#elif HAS_FAN2
- #define FAN_COUNT 3
-#elif HAS_FAN1
- #define FAN_COUNT 2
-#elif HAS_FAN0
- #define FAN_COUNT 1
-#else
- #define FAN_COUNT 0
-#endif
-
-#if FAN_COUNT > 0
- #define HAS_FAN 1
-#endif
-
-/**
- * Part Cooling fan multipliexer
- */
-#if PIN_EXISTS(FANMUX0)
- #define HAS_FANMUX 1
-#endif
-
-/**
- * MIN/MAX fan PWM scaling
- */
-#ifndef FAN_OFF_PWM
- #define FAN_OFF_PWM 0
-#endif
-#ifndef FAN_MIN_PWM
- #if FAN_OFF_PWM > 0
- #define FAN_MIN_PWM (FAN_OFF_PWM + 1)
- #else
- #define FAN_MIN_PWM 0
- #endif
-#endif
-#ifndef FAN_MAX_PWM
- #define FAN_MAX_PWM 255
-#endif
-#if FAN_MIN_PWM < 0 || FAN_MIN_PWM > 255
- #error "FAN_MIN_PWM must be a value from 0 to 255."
-#elif FAN_MAX_PWM < 0 || FAN_MAX_PWM > 255
- #error "FAN_MAX_PWM must be a value from 0 to 255."
-#elif FAN_MIN_PWM > FAN_MAX_PWM
- #error "FAN_MIN_PWM must be less than or equal to FAN_MAX_PWM."
-#elif FAN_OFF_PWM > FAN_MIN_PWM
- #error "FAN_OFF_PWM must be less than or equal to FAN_MIN_PWM."
-#endif
-
-/**
- * FAST PWM FAN Settings
- */
-#if ENABLED(FAST_PWM_FAN) && !defined(FAST_PWM_FAN_FREQUENCY)
- #define FAST_PWM_FAN_FREQUENCY ((F_CPU) / (2 * 255 * 1)) // Fan frequency default
-#endif
-
/**
* MIN/MAX case light PWM scaling
*/
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h
index 36ccbee9b9c9..f416ca88bd79 100644
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@@ -416,8 +416,19 @@
#error "MBL_Z_STEP is now MESH_EDIT_Z_STEP."
#elif defined(CHDK)
#error "CHDK is now CHDK_PIN."
-#elif defined(MAX6675_SS) || defined(MAX6675_SS2)
- #error "MAX6675_SS / MAX6675_SS2 is now MAX6675_SS_PIN / MAX6675_SS2_PIN."
+#elif ANY_PIN( \
+ MAX6675_SS, MAX6675_SS2, MAX6675_CS, MAX6675_CS2, \
+ MAX31855_SS, MAX31855_SS2, MAX31855_CS, MAX31855_CS2, \
+ MAX31865_SS, MAX31865_SS2, MAX31865_CS, MAX31865_CS2)
+ #warning "MAX*_SS_PIN, MAX*_SS2_PIN, MAX*_CS_PIN, and MAX*_CS2_PIN are deprecated and will be removed in a future version. Please use TEMP_0_CS_PIN/TEMP_1_CS_PIN instead."
+#elif ANY_PIN(MAX6675_SCK, MAX31855_SCK, MAX31865_SCK)
+ #warning "MAX*_SCK_PIN is deprecated and will be removed in a future version. Please use TEMP_0_SCK_PIN/TEMP_1_SCK_PIN instead."
+#elif ANY_PIN(MAX6675_MISO, MAX6675_DO, MAX31855_MISO, MAX31855_DO, MAX31865_MISO, MAX31865_DO)
+ #warning "MAX*_MISO_PIN and MAX*_DO_PIN are deprecated and will be removed in a future version. Please use TEMP_0_MISO_PIN/TEMP_1_MISO_PIN instead."
+#elif PIN_EXISTS(MAX31865_MOSI)
+ #warning "MAX31865_MOSI_PIN is deprecated and will be removed in a future version. Please use TEMP_0_MOSI_PIN/TEMP_1_MOSI_PIN instead."
+#elif ANY_PIN(THERMO_CS1_PIN, THERMO_CS2_PIN, THERMO_DO_PIN, THERMO_SCK_PIN)
+ #error "THERMO_*_PIN is now TEMP_n_CS_PIN, TEMP_n_SCK_PIN, TEMP_n_MOSI_PIN, TEMP_n_MISO_PIN."
#elif defined(MAX31865_SENSOR_OHMS)
#error "MAX31865_SENSOR_OHMS is now MAX31865_SENSOR_OHMS_0."
#elif defined(MAX31865_CALIBRATION_OHMS)
@@ -1953,14 +1964,21 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#endif
/**
- * Pins and Sensor IDs must be set for each heater
+ * Required MAX31865 settings
*/
-#if TEMP_SENSOR_0_IS_MAX6675 && !ANY_PIN(MAX6675_SS, MAX31855_CS, MAX31865_CS, MAX6675_CS)
- #error "TEMP_SENSOR_0 -2 requires a MAX6675_SS_PIN, MAX6675_CS_PIN, MAX31855_CS_PIN, or MAX31865_CS_PIN."
-#elif HAS_HOTEND && !HAS_TEMP_HOTEND && !TEMP_SENSOR_0_IS_DUMMY
- #error "TEMP_0_PIN (required for TEMP_SENSOR_0) not defined for this board."
-#elif EITHER(HAS_MULTI_HOTEND, HEATERS_PARALLEL) && !HAS_HEATER_1
- #error "HEATER_1_PIN is not defined. TEMP_SENSOR_1 might not be set, or the board (not EEB / EEF?) doesn't define a pin."
+#if TEMP_SENSOR_0_IS_MAX31865 || (TEMP_SENSOR_REDUNDANT_IS_MAX31865 && TEMP_SENSOR_REDUNDANT_SOURCE == 0)
+ #if !defined(MAX31865_SENSOR_WIRES_0) || !WITHIN(MAX31865_SENSOR_WIRES_0, 2, 4)
+ #error "MAX31865_SENSOR_WIRES_0 must be defined as an integer between 2 and 4."
+ #elif !defined(MAX31865_SENSOR_OHMS_0) || !defined(MAX31865_CALIBRATION_OHMS_0)
+ #error "MAX31865_SENSOR_OHMS_0 and MAX31865_CALIBRATION_OHMS_0 must be set if TEMP_SENSOR_0/TEMP_SENSOR_REDUNDANT is MAX31865."
+ #endif
+#endif
+#if TEMP_SENSOR_1_IS_MAX31865 || (TEMP_SENSOR_REDUNDANT_IS_MAX31865 && TEMP_SENSOR_REDUNDANT_SOURCE == 1)
+ #if !defined(MAX31865_SENSOR_WIRES_1) || !WITHIN(MAX31865_SENSOR_WIRES_1, 2, 4)
+ #error "MAX31865_SENSOR_WIRES_1 must be defined as an integer between 2 and 4."
+ #elif !defined(MAX31865_SENSOR_OHMS_1) || !defined(MAX31865_CALIBRATION_OHMS_1)
+ #error "MAX31865_SENSOR_OHMS_1 and MAX31865_CALIBRATION_OHMS_1 must be set if TEMP_SENSOR_1/TEMP_SENSOR_REDUNDANT is MAX31865."
+ #endif
#endif
/**
@@ -2023,20 +2041,36 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "TEMP_SENSOR_REDUNDANT_TARGET can't be Cooler (-5): requires TEMP_COOLER_PIN"
#endif
- #if TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 0 && !PIN_EXISTS(MAX6675_SS)
- #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE 0 requires a MAX6675_SS_PIN, MAX6675_CS_PIN, MAX31855_CS_PIN, or MAX31865_CS_PIN."
- #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1 && !PIN_EXISTS(MAX6675_SS2)
- #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE 1 requires a MAX6675_SS2_PIN, MAX6675_CS_PIN, MAX31855_CS_PIN, or MAX31865_CS_PIN."
+ #if TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 0 && !PIN_EXISTS(TEMP_0_CS)
+ #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE 0 requires TEMP_0_CS_PIN."
+ #elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1 && !PIN_EXISTS(TEMP_1_CS)
+ #error "TEMP_SENSOR_REDUNDANT MAX Thermocouple with TEMP_SENSOR_REDUNDANT_SOURCE 1 requires TEMP_1_CS_PIN."
#endif
#endif
+/**
+ * Test Sensor & Heater pin combos.
+ * Pins and Sensor IDs must be set for each heater
+ */
+#if !ANY_PIN(TEMP_0, TEMP_0_CS)
+ #error "TEMP_0_PIN or TEMP_0_CS_PIN not defined for this board."
+#elif !HAS_HEATER_0 && EXTRUDERS
+ #error "HEATER_0_PIN not defined for this board."
+#elif TEMP_SENSOR_0_IS_MAX_TC && !PIN_EXISTS(TEMP_0_CS)
+ #error "TEMP_SENSOR_0 MAX thermocouple requires TEMP_0_CS_PIN."
+#elif HAS_HOTEND && !HAS_TEMP_HOTEND && !TEMP_SENSOR_0_IS_DUMMY
+ #error "TEMP_0_PIN (required for TEMP_SENSOR_0) not defined for this board."
+#elif EITHER(HAS_MULTI_HOTEND, HEATERS_PARALLEL) && !HAS_HEATER_1
+ #error "HEATER_1_PIN is not defined. TEMP_SENSOR_1 might not be set, or the board (not EEB / EEF?) doesn't define a pin."
+#endif
+
#if HAS_MULTI_HOTEND
- #if TEMP_SENSOR_1_IS_MAX6675 && !ANY_PIN(MAX6675_SS2, MAX31855_CS2, MAX31865_CS2, MAX6675_CS2)
- #error "TEMP_SENSOR_1 requires a MAX6675_SS2_PIN, MAX6675_CS2_PIN, MAX31855_CS2_PIN, or MAX31865_CS2_PIN."
+ #if TEMP_SENSOR_1_IS_MAX_TC && !PIN_EXISTS(TEMP_1_CS)
+ #error "TEMP_SENSOR_1 MAX thermocouple requires TEMP_1_CS_PIN."
#elif TEMP_SENSOR_1 == 0
#error "TEMP_SENSOR_1 is required with 2 or more HOTENDS."
- #elif !ANY_PIN(TEMP_1, MAX6675_SS2) && !TEMP_SENSOR_1_IS_DUMMY
- #error "TEMP_1_PIN or MAX6675_SS2_PIN not defined for this board."
+ #elif !ANY_PIN(TEMP_1, TEMP_1_CS) && !TEMP_SENSOR_1_IS_DUMMY
+ #error "TEMP_1_PIN or TEMP_1_CS_PIN not defined for this board."
#endif
#if HOTENDS > 2
#if TEMP_SENSOR_2 == 0
@@ -2148,14 +2182,31 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "TEMP_SENSOR_6 shouldn't be set with only 1 HOTEND."
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 1 HOTEND."
-#endif
+#endif // HAS_MULTI_HOTEND
+/**
+ * Pins must be set for temp sensors, with some other feature requirements.
+ */
#if TEMP_SENSOR_CHAMBER && !PIN_EXISTS(TEMP_CHAMBER)
#error "TEMP_SENSOR_CHAMBER requires TEMP_CHAMBER_PIN."
#endif
-#if TEMP_SENSOR_COOLER && !(PIN_EXISTS(TEMP_COOLER) && ENABLED(LASER_FEATURE))
- #error "TEMP_SENSOR_COOLER requires LASER_FEATURE and TEMP_COOLER_PIN."
+#if TEMP_SENSOR_COOLER
+ #if !PIN_EXISTS(TEMP_COOLER)
+ #error "TEMP_SENSOR_COOLER requires TEMP_COOLER_PIN."
+ #elif DISABLED(LASER_FEATURE)
+ #error "TEMP_SENSOR_COOLER requires LASER_FEATURE."
+ #endif
+#endif
+
+#if TEMP_SENSOR_PROBE
+ #if !PIN_EXISTS(TEMP_PROBE)
+ #error "TEMP_SENSOR_PROBE requires TEMP_PROBE_PIN."
+ #elif !HAS_TEMP_ADC_PROBE
+ #error "TEMP_PROBE_PIN must be an ADC pin."
+ #elif DISABLED(FIX_MOUNTED_PROBE)
+ #error "TEMP_SENSOR_PROBE shouldn't be set without FIX_MOUNTED_PROBE."
+ #endif
#endif
#if ENABLED(LASER_COOLANT_FLOW_METER) && !(PIN_EXISTS(FLOWMETER) && ENABLED(LASER_FEATURE))
@@ -2186,41 +2237,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#endif
#endif
-#if TEMP_SENSOR_PROBE
- #if !PIN_EXISTS(TEMP_PROBE)
- #error "TEMP_SENSOR_PROBE requires TEMP_PROBE_PIN."
- #elif !HAS_TEMP_ADC_PROBE
- #error "TEMP_PROBE_PIN must be an ADC pin."
- #elif DISABLED(FIX_MOUNTED_PROBE)
- #error "TEMP_SENSOR_PROBE shouldn't be set without FIX_MOUNTED_PROBE."
- #endif
-#endif
-
-#if TEMP_SENSOR_IS_MAX(0, MAX31865) && !(defined(MAX31865_SENSOR_OHMS_0) && defined(MAX31865_CALIBRATION_OHMS_0))
- #error "MAX31865_SENSOR_OHMS_0 and MAX31865_CALIBRATION_OHMS_0 must be set if TEMP_SENSOR_0/TEMP_SENSOR_REDUNDANT is MAX31865."
-#elif TEMP_SENSOR_IS_MAX(1, MAX31865) && !(defined(MAX31865_SENSOR_OHMS_1) && defined(MAX31865_CALIBRATION_OHMS_1))
- #error "MAX31865_SENSOR_OHMS_1 and MAX31865_CALIBRATION_OHMS_1 must be set if TEMP_SENSOR_1/TEMP_SENSOR_REDUNDANT is MAX31865."
-#endif
-
-/**
- * Test Heater, Temp Sensor, and Extruder Pins
- */
-#if !HAS_HEATER_0 && EXTRUDERS
- #error "HEATER_0_PIN not defined for this board."
-#elif !ANY_PIN(TEMP_0, MAX6675_SS)
- #error "TEMP_0_PIN or MAX6675_SS not defined for this board."
-#endif
-
-#if HAS_EXTRUDERS
- #if ((defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && !PINS_EXIST(E0_STEP, E0_DIR))
- #error "E0_STEP_PIN or E0_DIR_PIN not defined for this board."
- #elif ( !(defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PINS_EXIST(E0_STEP, E0_DIR) || !HAS_E0_ENABLE))
- #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
- #elif EXTRUDERS && TEMP_SENSOR_0 == 0
- #error "TEMP_SENSOR_0 is required if there are any extruders."
- #endif
-#endif
-
/**
* Temperature status LEDs
*/
@@ -2262,6 +2278,16 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
/**
* Test Extruder Stepper Pins
*/
+#if HAS_EXTRUDERS
+ #if ((defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && !PINS_EXIST(E0_STEP, E0_DIR))
+ #error "E0_STEP_PIN or E0_DIR_PIN not defined for this board."
+ #elif ( !(defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PINS_EXIST(E0_STEP, E0_DIR) || !HAS_E0_ENABLE))
+ #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
+ #elif EXTRUDERS && TEMP_SENSOR_0 == 0
+ #error "TEMP_SENSOR_0 is required if there are any extruders."
+ #endif
+#endif
+
#if E_STEPPERS
#if !(PINS_EXIST(E0_STEP, E0_DIR) && HAS_E0_ENABLE)
#error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
diff --git a/Marlin/src/libs/MAX31865.cpp b/Marlin/src/libs/MAX31865.cpp
new file mode 100644
index 000000000000..590dea5ca5d9
--- /dev/null
+++ b/Marlin/src/libs/MAX31865.cpp
@@ -0,0 +1,500 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+
+/**
+ * Based on Based on Adafruit MAX31865 library:
+ *
+ * This is a library for the Adafruit PT100/P1000 RTD Sensor w/MAX31865
+ * Designed specifically to work with the Adafruit RTD Sensor
+ * https://www.adafruit.com/products/3328
+ *
+ * This sensor uses SPI to communicate, 4 pins are required to interface.
+ *
+ * Adafruit invests time and resources providing this open source code,
+ * please support Adafruit and open-source hardware by purchasing
+ * products from Adafruit!
+ *
+ * Written by Limor Fried/Ladyada for Adafruit Industries.
+ *
+ * Modifications by JoAnn Manges (@GadgetAngel)
+ * Copyright (c) 2020, JoAnn Manges
+ * All rights reserved.
+ */
+
+// Useful for RTD debugging.
+//#define MAX31865_DEBUG
+//#define MAX31865_DEBUG_SPI
+
+//TODO: switch to SPIclass/SoftSPI
+
+#include "../inc/MarlinConfig.h"
+
+#if HAS_MAX31865 && !LIB_USR_MAX31865
+
+#include "MAX31865.h"
+
+// The maximum speed the MAX31865 can do is 5 MHz
+SPISettings MAX31865::spiConfig = SPISettings(
+ #if defined(TARGET_LPC1768)
+ SPI_QUARTER_SPEED
+ #elif defined(ARDUINO_ARCH_STM32)
+ SPI_CLOCK_DIV4
+ #else
+ 500000
+ #endif
+ , MSBFIRST
+ , SPI_MODE_1 // CPOL0 CPHA1
+);
+
+#ifndef LARGE_PINMAP
+
+ /**
+ * Create the interface object using software (bitbang) SPI for PIN values
+ * less than or equal to 127.
+ *
+ * @param spi_cs the SPI CS pin to use
+ * @param spi_mosi the SPI MOSI pin to use
+ * @param spi_miso the SPI MISO pin to use
+ * @param spi_clk the SPI clock pin to use
+ */
+ MAX31865::MAX31865(int8_t spi_cs, int8_t spi_mosi, int8_t spi_miso, int8_t spi_clk) {
+ _cs = spi_cs;
+ _mosi = spi_mosi;
+ _miso = spi_miso;
+ _sclk = spi_clk;
+ }
+
+ /**
+ * Create the interface object using hardware SPI for PIN for PIN values less
+ * than or equal to 127.
+ *
+ * @param spi_cs the SPI CS pin to use along with the default SPI device
+ */
+ MAX31865::MAX31865(int8_t spi_cs) {
+ _cs = spi_cs;
+ _sclk = _miso = _mosi = -1;
+ }
+
+#else
+
+ /**
+ * Create the interface object using software (bitbang) SPI for PIN values
+ * which are larger than 127. If you have PIN values less than or equal to
+ * 127 use the other call for SW SPI.
+ *
+ * @param spi_cs the SPI CS pin to use
+ * @param spi_mosi the SPI MOSI pin to use
+ * @param spi_miso the SPI MISO pin to use
+ * @param spi_clk the SPI clock pin to use
+ * @param pin_mapping set to 1 for positive pin values
+ */
+ MAX31865::MAX31865(uint32_t spi_cs, uint32_t spi_mosi,
+ uint32_t spi_miso, uint32_t spi_clk,
+ uint8_t pin_mapping) {
+ _cs = spi_cs;
+ _mosi = spi_mosi;
+ _miso = spi_miso;
+ _sclk = spi_clk;
+ }
+
+ /**
+ * Create the interface object using hardware SPI for PIN values which are
+ * larger than 127. If you have PIN values less than or equal to 127 use
+ * the other call for HW SPI.
+ *
+ * @param spi_cs the SPI CS pin to use along with the default SPI device
+ * @param pin_mapping set to 1 for positive pin values
+ */
+ MAX31865::MAX31865(uint32_t spi_cs, uint8_t pin_mapping) {
+ _cs = spi_cs;
+ _sclk = _miso = _mosi = -1UL; //-1UL or 0xFFFFFFFF or 4294967295
+ }
+
+#endif // LARGE_PINMAP
+
+
+/**
+ *
+ * Instance & Class methods
+ *
+ */
+
+
+/**
+ * Initialize the SPI interface and set the number of RTD wires used
+ *
+ * @param wires The number of wires in enum format. Can be MAX31865_2WIRE, MAX31865_3WIRE, or MAX31865_4WIRE.
+ * @param zero The resistance of the RTD at 0 degC, in ohms.
+ * @param ref The resistance of the reference resistor, in ohms.
+ */
+void MAX31865::begin(max31865_numwires_t wires, float zero, float ref) {
+ Rzero = zero;
+ Rref = ref;
+
+ OUT_WRITE(_cs, HIGH);
+
+ if (_sclk != TERN(LARGE_PINMAP, -1UL, -1)) {
+ // define pin modes for Software SPI
+ #ifdef MAX31865_DEBUG
+ SERIAL_ECHOLN("Initializing MAX31865 Software SPI");
+ #endif
+
+ OUT_WRITE(_sclk, LOW);
+ SET_OUTPUT(_mosi);
+ SET_INPUT(_miso);
+ } else {
+ // start and configure hardware SPI
+ #ifdef MAX31865_DEBUG
+ SERIAL_ECHOLN("Initializing MAX31865 Hardware SPI");
+ #endif
+
+ SPI.begin();
+ }
+
+ setWires(wires);
+ enableBias(false);
+ autoConvert(false);
+ clearFault();
+
+ #ifdef MAX31865_DEBUG_SPI
+ #ifndef LARGE_PINMAP
+ SERIAL_ECHOLNPAIR(
+ "Regular begin call with _cs: ", _cs,
+ " _miso: ", _miso,
+ " _sclk: ", _sclk,
+ " _mosi: ", _mosi
+ );
+ #else
+ SERIAL_ECHOLNPAIR(
+ "LARGE_PINMAP begin call with _cs: ", _cs,
+ " _miso: ", _miso,
+ " _sclk: ", _sclk,
+ " _mosi: ", _mosi
+ );
+ #endif // LARGE_PINMAP
+
+ SERIAL_ECHOLNPAIR("config: ", readRegister8(MAX31856_CONFIG_REG));
+ SERIAL_EOL();
+ #endif // MAX31865_DEBUG_SPI
+}
+
+/**
+ * Read the raw 8-bit FAULTSTAT register
+ *
+ * @return The raw unsigned 8-bit FAULT status register
+ */
+uint8_t MAX31865::readFault() {
+ return readRegister8(MAX31856_FAULTSTAT_REG);
+}
+
+/**
+ * Clear all faults in FAULTSTAT.
+ */
+void MAX31865::clearFault() {
+ setConfig(MAX31856_CONFIG_FAULTSTAT, 1);
+}
+
+/**
+ * Whether we want to have continuous conversions (50/60 Hz)
+ *
+ * @param b If true, auto conversion is enabled
+ */
+void MAX31865::autoConvert(bool b) {
+ setConfig(MAX31856_CONFIG_MODEAUTO, b);
+}
+
+/**
+ * Whether we want filter out 50Hz noise or 60Hz noise
+ *
+ * @param b If true, 50Hz noise is filtered, else 60Hz(default)
+ */
+void MAX31865::enable50HzFilter(bool b) {
+ setConfig(MAX31856_CONFIG_FILT50HZ, b);
+}
+
+/**
+ * Enable the bias voltage on the RTD sensor
+ *
+ * @param b If true bias is enabled, else disabled
+ */
+void MAX31865::enableBias(bool b) {
+ setConfig(MAX31856_CONFIG_BIAS, b);
+
+ // From the datasheet:
+ // Note that if VBIAS is off (to reduce supply current between conversions), any filter
+ // capacitors at the RTDIN inputs need to charge before an accurate conversion can be
+ // performed. Therefore, enable VBIAS and wait at least 10.5 time constants of the input
+ // RC network plus an additional 1ms before initiating the conversion.
+ if (b)
+ DELAY_US(11500); //11.5ms
+}
+
+/**
+ * Start a one-shot temperature reading.
+ */
+void MAX31865::oneShot() {
+ setConfig(MAX31856_CONFIG_1SHOT, 1);
+
+ // From the datasheet:
+ // Note that a single conversion requires approximately 52ms in 60Hz filter
+ // mode or 62.5ms in 50Hz filter mode to complete. 1-Shot is a self-clearing bit.
+ // TODO: switch this out depeding on the filter mode.
+ DELAY_US(65000); // 65ms
+}
+
+/**
+ * How many wires we have in our RTD setup, can be MAX31865_2WIRE,
+ * MAX31865_3WIRE, or MAX31865_4WIRE
+ *
+ * @param wires The number of wires in enum format
+ */
+void MAX31865::setWires(max31865_numwires_t wires) {
+ uint8_t t = readRegister8(MAX31856_CONFIG_REG);
+ if (wires == MAX31865_3WIRE)
+ t |= MAX31856_CONFIG_3WIRE;
+ else // 2 or 4 wire
+ t &= ~MAX31856_CONFIG_3WIRE;
+ writeRegister8(MAX31856_CONFIG_REG, t);
+}
+
+/**
+ * Read the raw 16-bit value from the RTD_REG in one shot mode. This will include
+ * the fault bit, D0.
+ *
+ * @return The raw unsigned 16-bit register value with ERROR bit attached, NOT temperature!
+ */
+uint16_t MAX31865::readRaw() {
+ clearFault();
+ enableBias(true);
+
+ oneShot();
+ uint16_t rtd = readRegister16(MAX31856_RTDMSB_REG);
+
+ #ifdef MAX31865_DEBUG
+ SERIAL_ECHOLNPAIR("RTD MSB:", (rtd >> 8), " RTD LSB:", (rtd & 0x00FF));
+ #endif
+
+ // Disable the bias to lower power dissipation between reads.
+ // If the ref resistor heats up, the temperature reading will be skewed.
+ enableBias(false);
+
+ return rtd;
+}
+
+/**
+ * Calulate and return the resistance value of the connected RTD.
+ *
+ * @param refResistor The value of the matching reference resistor, usually 430 or 4300
+ * @return The raw RTD resistance value, NOT temperature!
+ */
+float MAX31865::readResistance() {
+ // Strip the error bit (D0) and convert to a float ratio.
+ // less precise method: (readRaw() * Rref) >> 16
+ return (((readRaw() >> 1) / 32768.0f) * Rref);
+}
+
+/**
+ * Read the RTD and pass it to temperature(float) for calculation.
+ *
+ * @return Temperature in C
+ */
+float MAX31865::temperature() {
+ return temperature(readResistance());
+}
+
+/**
+ * Given the 15-bit ADC value, calculate the resistance and pass it to temperature(float) for calculation.
+ *
+ * @return Temperature in C
+ */
+float MAX31865::temperature(uint16_t adcVal) {
+ return temperature(((adcVal) / 32768.0f) * Rref);
+}
+
+/**
+ * Calculate the temperature in C from the RTD resistance.
+ * Uses the technique outlined in this PDF:
+ * http://www.analog.com/media/en/technical-documentation/application-notes/AN709_0.pdf
+ *
+ * @param Rrtd the resistance value in ohms
+ * @return the temperature in degC
+ */
+float MAX31865::temperature(float Rrtd) {
+ float temp = (RTD_Z1 + sqrt(RTD_Z2 + (RTD_Z3 * Rrtd))) / RTD_Z4;
+
+ // From the PDF...
+ //
+ // The previous equation is valid only for temperatures of 0°C and above.
+ // The equation for RRTD(t) that defines negative temperature behavior is a
+ // fourth-order polynomial (after expanding the third term) and is quite
+ // impractical to solve for a single expression of temperature as a function
+ // of resistance.
+ //
+ if (temp < 0) {
+ Rrtd = (Rrtd / Rzero) * 100; // normalize to 100 ohm
+ float rpoly = Rrtd;
+
+ temp = -242.02 + (2.2228 * rpoly);
+ rpoly *= Rrtd; // square
+ temp += 2.5859e-3 * rpoly;
+ rpoly *= Rrtd; // ^3
+ temp -= 4.8260e-6 * rpoly;
+ rpoly *= Rrtd; // ^4
+ temp -= 2.8183e-8 * rpoly;
+ rpoly *= Rrtd; // ^5
+ temp += 1.5243e-10 * rpoly;
+ }
+
+ return temp;
+}
+
+//
+// private:
+//
+
+
+/**
+ * Set a value in the configuration register.
+ *
+ * @param config 8-bit value for the config item
+ * @param enable whether to enable or disable the value
+ */
+void MAX31865::setConfig(uint8_t config, bool enable) {
+ uint8_t t = readRegister8(MAX31856_CONFIG_REG);
+ if (enable)
+ t |= config;
+ else
+ t &= ~config; // disable
+ writeRegister8(MAX31856_CONFIG_REG, t);
+}
+
+/**
+ * Read a single byte from the specified register address.
+ *
+ * @param addr the register address
+ * @return the register contents
+ */
+uint8_t MAX31865::readRegister8(uint8_t addr) {
+ uint8_t ret = 0;
+ readRegisterN(addr, &ret, 1);
+
+ return ret;
+}
+
+/**
+ * Read two bytes: 1 from the specified register address, and 1 from the next address.
+ *
+ * @param addr the first register address
+ * @return both register contents as a single 16-bit int
+ */
+uint16_t MAX31865::readRegister16(uint8_t addr) {
+ uint8_t buffer[2] = {0, 0};
+ readRegisterN(addr, buffer, 2);
+
+ uint16_t ret = buffer[0];
+ ret <<= 8;
+ ret |= buffer[1];
+
+ return ret;
+}
+
+/**
+ * Read +n+ bytes from a specified address into +buffer+. Set D7 to 0 to specify a read.
+ *
+ * @param addr the first register address
+ * @param buffer storage for the read bytes
+ * @param n the number of bytes to read
+ */
+void MAX31865::readRegisterN(uint8_t addr, uint8_t buffer[], uint8_t n) {
+ addr &= 0x7F; // make sure top bit is not set
+ if (_sclk == TERN(LARGE_PINMAP, -1UL, -1))
+ SPI.beginTransaction(spiConfig);
+ else
+ WRITE(_sclk, LOW);
+
+ WRITE(_cs, LOW);
+ spixfer(addr);
+
+ while (n--) {
+ buffer[0] = spixfer(0xFF);
+ #ifdef MAX31865_DEBUG_SPI
+ SERIAL_ECHOLNPAIR("buffer read ", n, " data: ", buffer[0]);
+ #endif
+ buffer++;
+ }
+
+ if (_sclk == TERN(LARGE_PINMAP, -1UL, -1))
+ SPI.endTransaction();
+
+ WRITE(_cs, HIGH);
+}
+
+/**
+ * Write an 8-bit value to a register. Set D7 to 1 to specify a write.
+ *
+ * @param addr the address to write to
+ * @param data the data to write
+ */
+void MAX31865::writeRegister8(uint8_t addr, uint8_t data) {
+ if (_sclk == TERN(LARGE_PINMAP, -1UL, -1))
+ SPI.beginTransaction(spiConfig);
+ else
+ WRITE(_sclk, LOW);
+
+ WRITE(_cs, LOW);
+
+ spixfer(addr | 0x80); // make sure top bit is set
+ spixfer(data);
+
+ if (_sclk == TERN(LARGE_PINMAP, -1UL, -1))
+ SPI.endTransaction();
+
+ WRITE(_cs, HIGH);
+}
+
+/**
+ * Transfer SPI data +x+ and read the response. From the datasheet...
+ * Input data (SDI) is latched on the internal strobe edge and output data (SDO) is
+ * shifted out on the shift edge. There is one clock for each bit transferred.
+ * Address and data bits are transferred in groups of eight, MSB first.
+ *
+ * @param x an 8-bit chunk of data to write
+ * @return the 8-bit response
+ */
+uint8_t MAX31865::spixfer(uint8_t x) {
+ if (_sclk == TERN(LARGE_PINMAP, -1UL, -1))
+ return SPI.transfer(x);
+
+ uint8_t reply = 0;
+ for (int i = 7; i >= 0; i--) {
+ reply <<= 1;
+ WRITE(_sclk, HIGH);
+ WRITE(_mosi, x & (1 << i));
+ WRITE(_sclk, LOW);
+ if (READ(_miso))
+ reply |= 1;
+ }
+
+ return reply;
+}
+
+#endif // HAS_MAX31865 && !LIB_USR_MAX31865
diff --git a/Marlin/src/libs/MAX31865.h b/Marlin/src/libs/MAX31865.h
new file mode 100644
index 000000000000..2ab78ecbe8cf
--- /dev/null
+++ b/Marlin/src/libs/MAX31865.h
@@ -0,0 +1,131 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+
+/**
+ * Based on Adafruit MAX31865 library:
+ *
+ * This is a library for the Adafruit PT100/P1000 RTD Sensor w/MAX31865
+ * Designed specifically to work with the Adafruit RTD Sensor
+ * https://www.adafruit.com/products/3328
+ *
+ * This sensor uses SPI to communicate, 4 pins are required to interface.
+ *
+ * Adafruit invests time and resources providing this open source code,
+ * please support Adafruit and open-source hardware by purchasing
+ * products from Adafruit!
+ *
+ * Written by Limor Fried/Ladyada for Adafruit Industries.
+ *
+ * Modifications by JoAnn Manges (@GadgetAngel)
+ * Copyright (c) 2020, JoAnn Manges
+ * All rights reserved.
+ */
+#pragma once
+
+#include "../inc/MarlinConfig.h"
+#include "../HAL/shared/Delay.h"
+#include HAL_PATH(../HAL, MarlinSPI.h)
+
+#define MAX31856_CONFIG_REG 0x00
+#define MAX31856_CONFIG_BIAS 0x80
+#define MAX31856_CONFIG_MODEAUTO 0x40
+#define MAX31856_CONFIG_MODEOFF 0x00
+#define MAX31856_CONFIG_1SHOT 0x20
+#define MAX31856_CONFIG_3WIRE 0x10
+#define MAX31856_CONFIG_24WIRE 0x00
+#define MAX31856_CONFIG_FAULTSTAT 0x02
+#define MAX31856_CONFIG_FILT50HZ 0x01
+#define MAX31856_CONFIG_FILT60HZ 0x00
+
+#define MAX31856_RTDMSB_REG 0x01
+#define MAX31856_RTDLSB_REG 0x02
+#define MAX31856_HFAULTMSB_REG 0x03
+#define MAX31856_HFAULTLSB_REG 0x04
+#define MAX31856_LFAULTMSB_REG 0x05
+#define MAX31856_LFAULTLSB_REG 0x06
+#define MAX31856_FAULTSTAT_REG 0x07
+
+#define MAX31865_FAULT_HIGHTHRESH 0x80 // D7
+#define MAX31865_FAULT_LOWTHRESH 0x40 // D6
+#define MAX31865_FAULT_REFINLOW 0x20 // D5
+#define MAX31865_FAULT_REFINHIGH 0x10 // D4
+#define MAX31865_FAULT_RTDINLOW 0x08 // D3
+#define MAX31865_FAULT_OVUV 0x04 // D2
+
+// http://www.analog.com/media/en/technical-documentation/application-notes/AN709_0.pdf
+// constants for calulating temperature from the measured RTD resistance.
+#define RTD_Z1 -0.0039083
+#define RTD_Z2 0.00001758480889
+#define RTD_Z3 -0.0000000231
+#define RTD_Z4 -0.000001155
+
+typedef enum max31865_numwires {
+ MAX31865_2WIRE = 0,
+ MAX31865_3WIRE = 1,
+ MAX31865_4WIRE = 0
+} max31865_numwires_t;
+
+/* Interface class for the MAX31865 RTD Sensor reader */
+class MAX31865 {
+private:
+ static SPISettings spiConfig;
+
+ TERN(LARGE_PINMAP, uint32_t, uint8_t) _sclk, _miso, _mosi, _cs;
+ float Rzero, Rref;
+
+ void setConfig(uint8_t config, bool enable);
+
+ void readRegisterN(uint8_t addr, uint8_t buffer[], uint8_t n);
+ uint8_t readRegister8(uint8_t addr);
+ uint16_t readRegister16(uint8_t addr);
+
+ void writeRegister8(uint8_t addr, uint8_t reg);
+ uint8_t spixfer(uint8_t addr);
+
+public:
+ #ifdef LARGE_PINMAP
+ MAX31865(uint32_t spi_cs, uint8_t pin_mapping);
+ MAX31865(uint32_t spi_cs, uint32_t spi_mosi, uint32_t spi_miso,
+ uint32_t spi_clk, uint8_t pin_mapping);
+ #else
+ MAX31865(int8_t spi_cs);
+ MAX31865(int8_t spi_cs, int8_t spi_mosi, int8_t spi_miso,
+ int8_t spi_clk);
+ #endif
+
+ void begin(max31865_numwires_t wires, float zero, float ref);
+
+ uint8_t readFault();
+ void clearFault();
+
+ void setWires(max31865_numwires_t wires);
+ void autoConvert(bool b);
+ void enable50HzFilter(bool b);
+ void enableBias(bool b);
+ void oneShot();
+
+ uint16_t readRaw();
+ float readResistance();
+ float temperature();
+ float temperature(uint16_t adcVal);
+ float temperature(float Rrtd);
+};
diff --git a/Marlin/src/module/motion.cpp b/Marlin/src/module/motion.cpp
index 63fdd5afc3db..eb6dc6597ce4 100644
--- a/Marlin/src/module/motion.cpp
+++ b/Marlin/src/module/motion.cpp
@@ -703,8 +703,7 @@ void restore_feedrate_and_scaling() {
* at the same positions relative to the machine.
*/
void update_software_endstops(const AxisEnum axis
- OPTARG(HAS_HOTEND_OFFSET, const uint8_t old_tool_index/*=0*/)
- OPTARG(HAS_HOTEND_OFFSET, const uint8_t new_tool_index/*=0*/)
+ OPTARG(HAS_HOTEND_OFFSET, const uint8_t old_tool_index/*=0*/, const uint8_t new_tool_index/*=0*/)
) {
#if ENABLED(DUAL_X_CARRIAGE)
diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp
index 9f32ce933bff..83187259ff46 100644
--- a/Marlin/src/module/temperature.cpp
+++ b/Marlin/src/module/temperature.cpp
@@ -34,6 +34,7 @@
#include "temperature.h"
#include "endstops.h"
#include "planner.h"
+#include "printcounter.h"
#if EITHER(HAS_COOLER, LASER_COOLANT_FLOW_METER)
#include "../feature/cooler.h"
@@ -56,112 +57,56 @@
#include "../feature/host_actions.h"
#endif
-#define TEMP_SENSOR_IS_ANY_MAX_TC(n) (ENABLED(TEMP_SENSOR_##n##_IS_MAX_TC) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX_TC) && ENABLED(TEMP_SENSOR_REDUNDANT_SOURCE) && TEMP_SENSOR_REDUNDANT_SOURCE == n))
+// MAX TC related macros
+#define TEMP_SENSOR_IS_MAX(n, M) (ENABLED(TEMP_SENSOR_##n##_IS_MAX##M) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX##M) && TEMP_SENSOR_REDUNDANT_SOURCE == (n)))
+#define TEMP_SENSOR_IS_ANY_MAX_TC(n) (ENABLED(TEMP_SENSOR_##n##_IS_MAX_TC) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX_TC) && TEMP_SENSOR_REDUNDANT_SOURCE == n))
-// LIB_MAX31855 can be added to the build_flags in platformio.ini to use a user-defined library
-#if LIB_USR_MAX31855
+// LIB_MAX6675 can be added to the build_flags in platformio.ini to use a user-defined library
+// If LIB_MAX6675 is not on the build_flags then raw SPI reads will be used.
+#if HAS_MAX6675 && LIB_USR_MAX6675
+ #include
+ #define HAS_MAX6675_LIBRARY 1
+#endif
+
+// LIB_MAX31855 can be added to the build_flags in platformio.ini to use a user-defined library.
+// If LIB_MAX31855 is not on the build_flags then raw SPI reads will be used.
+#if HAS_MAX31855 && LIB_USR_MAX31855
#include
- #if PIN_EXISTS(MAX31855_MISO) && PIN_EXISTS(MAX31855_SCK)
- #define MAX31855_USES_SW_SPI 1
- #endif
- #if TEMP_SENSOR_IS_MAX(0, MAX31855) && PIN_EXISTS(MAX31855_CS)
- #define HAS_MAX31855_TEMP 1
- Adafruit_MAX31855 max31855_0 = Adafruit_MAX31855(MAX31855_CS_PIN
- #if MAX31855_USES_SW_SPI
- , MAX31855_MISO_PIN, MAX31855_SCK_PIN // For software SPI also set MISO/SCK
- #endif
- #if ENABLED(LARGE_PINMAP)
- , HIGH
- #endif
- );
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX31855) && PIN_EXISTS(MAX31855_CS2)
- #define HAS_MAX31855_TEMP 1
- Adafruit_MAX31855 max31855_1 = Adafruit_MAX31855(MAX31855_CS2_PIN
- #if MAX31855_USES_SW_SPI
- , MAX31855_MISO_PIN, MAX31855_SCK_PIN // For software SPI also set MISO/SCK
- #endif
- #if ENABLED(LARGE_PINMAP)
- , HIGH
- #endif
- );
- #endif
+ #define HAS_MAX31855_LIBRARY 1
+ typedef Adafruit_MAX31855 MAX31855;
#endif
-// LIB_MAX31865 can be added to the build_flags in platformio.ini to use a user-defined library.
-// If LIB_MAX31865 is not on the build_flags then the Adafruit MAX31865 V1.1.0 library is used.
#if HAS_MAX31865
- #include
- #ifndef MAX31865_MOSI_PIN
- #define MAX31865_MOSI_PIN SD_MOSI_PIN
- #endif
- #if PIN_EXISTS(MAX31865_MISO) && PIN_EXISTS(MAX31865_SCK)
- #define MAX31865_USES_SW_SPI 1
- #endif
- #if TEMP_SENSOR_IS_MAX(0, MAX31865) && PIN_EXISTS(MAX31865_CS)
- #define HAS_MAX31865_TEMP 1
- Adafruit_MAX31865 max31865_0 = Adafruit_MAX31865(MAX31865_CS_PIN
- #if MAX31865_USES_SW_SPI && PIN_EXISTS(MAX31865_MOSI)
- , MAX31865_MOSI_PIN, MAX31865_MISO_PIN, MAX31865_SCK_PIN // For software SPI also set MOSI/MISO/SCK
- #endif
- #if ENABLED(LARGE_PINMAP)
- , HIGH
- #endif
- );
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX31865) && PIN_EXISTS(MAX31865_CS2)
- #define HAS_MAX31865_TEMP 1
- Adafruit_MAX31865 max31865_1 = Adafruit_MAX31865(MAX31865_CS2_PIN
- #if MAX31865_USES_SW_SPI && PIN_EXISTS(MAX31865_MOSI)
- , MAX31865_MOSI_PIN, MAX31865_MISO_PIN, MAX31865_SCK_PIN // For software SPI also set MOSI/MISO/SCK
- #endif
- #if ENABLED(LARGE_PINMAP)
- , HIGH
- #endif
- );
+ #if LIB_USR_MAX31865
+ #include
+ typedef Adafruit_MAX31865 MAX31865;
+ #else
+ #include "../libs/MAX31865.h"
#endif
#endif
-// LIB_MAX6675 can be added to the build_flags in platformio.ini to use a user-defined library
-#if LIB_USR_MAX6675
- #include
- #if PIN_EXISTS(MAX6675_MISO) && PIN_EXISTS(MAX6675_SCK)
- #define MAX6675_USES_SW_SPI 1
- #endif
- #if TEMP_SENSOR_IS_MAX(0, MAX6675) && PIN_EXISTS(MAX6675_CS)
- #define HAS_MAX6675_TEMP 1
- MAX6675 max6675_0 = MAX6675(MAX6675_CS_PIN
- #if MAX6675_USES_SW_SPI
- , MAX6675_MISO_PIN, MAX6675_SCK_PIN // For software SPI also set MISO/SCK
- #endif
- #if ENABLED(LARGE_PINMAP)
- , HIGH
- #endif
- );
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX6675) && PIN_EXISTS(MAX6675_CS2)
- #define HAS_MAX6675_TEMP 1
- MAX6675 max6675_1 = MAX6675(MAX6675_CS2_PIN
- #if MAX6675_USES_SW_SPI
- , MAX6675_MISO_PIN, MAX6675_SCK_PIN // For software SPI also set MISO/SCK
- #endif
- #if ENABLED(LARGE_PINMAP)
- , HIGH
- #endif
- );
- #endif
+#if HAS_MAX6675_LIBRARY || HAS_MAX31855_LIBRARY || HAS_MAX31865
+ #define HAS_MAXTC_LIBRARIES 1
#endif
-#if !HAS_MAX6675_TEMP && !HAS_MAX31855_TEMP && !HAS_MAX31865_TEMP
- #define NO_THERMO_TEMPS 1
+// If we have a MAX TC with SCK and MISO pins defined, it's either on a separate/dedicated Hardware
+// SPI bus, or some pins for Software SPI. Alternate Hardware SPI buses are not supported yet, so
+// your SPI options are:
+//
+// 1. Only CS pin(s) defined: Hardware SPI on the default bus (usually the SD card SPI).
+// 2. CS, MISO, and SCK pins defined: Software SPI on a separate bus, as defined by MISO, SCK.
+// 3. CS, MISO, and SCK pins w/ FORCE_HW_SPI: Hardware SPI on the default bus, ignoring MISO, SCK.
+//
+#if TEMP_SENSOR_IS_ANY_MAX_TC(0) && TEMP_SENSOR_0_HAS_SPI_PINS && DISABLED(TEMP_SENSOR_FORCE_HW_SPI)
+ #define TEMP_SENSOR_0_USES_SW_SPI 1
#endif
-
-#if (TEMP_SENSOR_0_IS_MAX_TC || TEMP_SENSOR_1_IS_MAX_TC || TEMP_SENSOR_REDUNDANT_IS_MAX_TC) && PINS_EXIST(MAX6675_SCK, MAX6675_DO) && NO_THERMO_TEMPS
- #define THERMO_SEPARATE_SPI 1
+#if TEMP_SENSOR_IS_ANY_MAX_TC(1) && TEMP_SENSOR_1_HAS_SPI_PINS && DISABLED(TEMP_SENSOR_FORCE_HW_SPI)
+ #define TEMP_SENSOR_1_USES_SW_SPI 1
#endif
-#if THERMO_SEPARATE_SPI
+#if (TEMP_SENSOR_0_USES_SW_SPI || TEMP_SENSOR_1_USES_SW_SPI) && !HAS_MAXTC_LIBRARIES
#include "../libs/private_spi.h"
+ #define HAS_MAXTC_SW_SPI 1
#endif
#if ENABLED(PID_EXTRUSION_SCALING)
@@ -172,8 +117,6 @@
#include "../feature/babystep.h"
#endif
-#include "printcounter.h"
-
#if ENABLED(FILAMENT_WIDTH_SENSOR)
#include "../feature/filwidth.h"
#endif
@@ -246,7 +189,67 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
#define _E_PSTR(h,N) ((HOTENDS) > N && (h) == N) ? PSTR(LCD_STR_E##N) :
#define HEATER_PSTR(h) _BED_PSTR(h) _CHAMBER_PSTR(h) _COOLER_PSTR(h) _E_PSTR(h,1) _E_PSTR(h,2) _E_PSTR(h,3) _E_PSTR(h,4) _E_PSTR(h,5) PSTR(LCD_STR_E0)
-// public:
+//
+// Initialize MAX TC objects/SPI
+//
+#if HAS_MAX_TC
+
+ #if HAS_MAXTC_SW_SPI
+ // Initialize SoftSPI for non-lib Software SPI; Libraries take care of it themselves.
+ template
+ SoftSPI SPIclass::softSPI;
+ SPIclass max_tc_spi;
+ #endif
+
+ #define MAXTC_INIT(n, M) \
+ MAX##M max##M##_##n = MAX##M( \
+ TEMP_##n##_CS_PIN \
+ OPTARG(_MAX31865_##n##_SW, TEMP_##n##_MOSI_PIN) \
+ OPTARG(TEMP_SENSOR_##n##_USES_SW_SPI, TEMP_##n##_MISO_PIN, TEMP_##n##_SCK_PIN) \
+ OPTARG(LARGE_PINMAP, HIGH) \
+ )
+
+ #if HAS_MAX6675_LIBRARY
+ #if TEMP_SENSOR_IS_MAX(0, 6675)
+ MAXTC_INIT(0, 6675);
+ #endif
+ #if TEMP_SENSOR_IS_MAX(1, 6675)
+ MAXTC_INIT(1, 6675);
+ #endif
+ #endif
+
+ #if HAS_MAX31855_LIBRARY
+ #if TEMP_SENSOR_IS_MAX(0, 31855)
+ MAXTC_INIT(0, 31855);
+ #endif
+ #if TEMP_SENSOR_IS_MAX(1, 31855)
+ MAXTC_INIT(1, 31855);
+ #endif
+ #endif
+
+ // MAX31865 always uses a library, unlike '55 & 6675
+ #if HAS_MAX31865
+ #define _MAX31865_0_SW TEMP_SENSOR_0_USES_SW_SPI
+ #define _MAX31865_1_SW TEMP_SENSOR_1_USES_SW_SPI
+
+ #if TEMP_SENSOR_IS_MAX(0, 31865)
+ MAXTC_INIT(0, 31865);
+ #endif
+ #if TEMP_SENSOR_IS_MAX(1, 31865)
+ MAXTC_INIT(1, 31865);
+ #endif
+
+ #undef _MAX31865_0_SW
+ #undef _MAX31865_1_SW
+ #endif
+
+ #undef MAXTC_INIT
+
+#endif
+
+/**
+ * public:
+ */
#if ENABLED(NO_FAN_SLOWING_IN_PID_TUNING)
bool Temperature::adaptive_fan_slowing = true;
@@ -274,6 +277,25 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
uint8_t Temperature::coolerfan_speed; // = 0
#endif
+// Init fans according to whether they're native PWM or Software PWM
+#ifdef BOARD_OPENDRAIN_MOSFETS
+ #define _INIT_SOFT_FAN(P) OUT_WRITE_OD(P, FAN_INVERTING ? LOW : HIGH)
+#else
+ #define _INIT_SOFT_FAN(P) OUT_WRITE(P, FAN_INVERTING ? LOW : HIGH)
+#endif
+#if ENABLED(FAN_SOFT_PWM)
+ #define _INIT_FAN_PIN(P) _INIT_SOFT_FAN(P)
+#else
+ #define _INIT_FAN_PIN(P) do{ if (PWM_PIN(P)) SET_PWM(P); else _INIT_SOFT_FAN(P); }while(0)
+#endif
+#if ENABLED(FAST_PWM_FAN)
+ #define SET_FAST_PWM_FREQ(P) set_pwm_frequency(P, FAST_PWM_FAN_FREQUENCY)
+#else
+ #define SET_FAST_PWM_FREQ(P) NOOP
+#endif
+#define INIT_FAN_PIN(P) do{ _INIT_FAN_PIN(P); SET_FAST_PWM_FREQ(P); }while(0)
+
+// HAS_FAN does not include CONTROLLER_FAN
#if HAS_FAN
uint8_t Temperature::fan_speed[FAN_COUNT]; // = { 0 }
@@ -419,7 +441,18 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
celsius_t Temperature::extrude_min_temp = EXTRUDE_MINTEMP;
#endif
-// private:
+#if HAS_ADC_BUTTONS
+ uint32_t Temperature::current_ADCKey_raw = HAL_ADC_RANGE;
+ uint16_t Temperature::ADCKey_count = 0;
+#endif
+
+#if ENABLED(PID_EXTRUSION_SCALING)
+ int16_t Temperature::lpq_len; // Initialized in settings.cpp
+#endif
+
+/**
+ * private:
+ */
volatile bool Temperature::raw_temps_ready = false;
@@ -472,16 +505,10 @@ volatile bool Temperature::raw_temps_ready = false;
bool Temperature::paused_for_probing;
#endif
-// public:
-
-#if HAS_ADC_BUTTONS
- uint32_t Temperature::current_ADCKey_raw = HAL_ADC_RANGE;
- uint16_t Temperature::ADCKey_count = 0;
-#endif
-
-#if ENABLED(PID_EXTRUSION_SCALING)
- int16_t Temperature::lpq_len; // Initialized in settings.cpp
-#endif
+/**
+ * public:
+ * Class and Instance Methods
+ */
#if HAS_PID_HEATING
@@ -758,10 +785,6 @@ volatile bool Temperature::raw_temps_ready = false;
#endif // HAS_PID_HEATING
-/**
- * Class and Instance Methods
- */
-
int16_t Temperature::getHeaterPower(const heater_id_t heater_id) {
switch (heater_id) {
#if HAS_HEATED_BED
@@ -781,6 +804,16 @@ int16_t Temperature::getHeaterPower(const heater_id_t heater_id) {
#define _EFANOVERLAP(A,B) _FANOVERLAP(E##A,B)
#if HAS_AUTO_FAN
+ #if EXTRUDER_AUTO_FAN_SPEED != 255
+ #define INIT_E_AUTO_FAN_PIN(P) do{ if (P == FAN1_PIN || P == FAN2_PIN) { SET_PWM(P); SET_FAST_PWM_FREQ(P); } else SET_OUTPUT(P); }while(0)
+ #else
+ #define INIT_E_AUTO_FAN_PIN(P) SET_OUTPUT(P)
+ #endif
+ #if CHAMBER_AUTO_FAN_SPEED != 255
+ #define INIT_CHAMBER_AUTO_FAN_PIN(P) do{ if (P == FAN1_PIN || P == FAN2_PIN) { SET_PWM(P); SET_FAST_PWM_FREQ(P); } else SET_OUTPUT(P); }while(0)
+ #else
+ #define INIT_CHAMBER_AUTO_FAN_PIN(P) SET_OUTPUT(P)
+ #endif
#define CHAMBER_FAN_INDEX HOTENDS
@@ -1668,11 +1701,6 @@ void Temperature::manage_heater() {
}
celsius_float_t Temperature::user_thermistor_to_deg_c(const uint8_t t_index, const int16_t raw) {
- //#if (MOTHERBOARD == BOARD_RAMPS_14_EFB)
- // static uint32_t clocks_total = 0;
- // static uint32_t calls = 0;
- // uint32_t tcnt5 = TCNT5;
- //#endif
if (!WITHIN(t_index, 0, COUNT(user_thermistor) - 1)) return 25;
@@ -1700,14 +1728,6 @@ void Temperature::manage_heater() {
value += t.sh_c_coeff * cu(log_resistance);
value = 1.0f / value;
- //#if (MOTHERBOARD == BOARD_RAMPS_14_EFB)
- // int32_t clocks = TCNT5 - tcnt5;
- // if (clocks >= 0) {
- // clocks_total += clocks;
- // calls++;
- // }
- //#endif
-
// Return degrees C (up to 999, as the LCD only displays 3 digits)
return _MIN(value + THERMISTOR_ABS_ZERO_C, 999);
}
@@ -1730,7 +1750,14 @@ void Temperature::manage_heater() {
#if TEMP_SENSOR_0_IS_CUSTOM
return user_thermistor_to_deg_c(CTI_HOTEND_0, raw);
#elif TEMP_SENSOR_0_IS_MAX_TC
- return TERN(TEMP_SENSOR_0_IS_MAX31865, max31865_0.temperature(MAX31865_SENSOR_OHMS_0, MAX31865_CALIBRATION_OHMS_0), raw * 0.25);
+ #if TEMP_SENSOR_0_IS_MAX31865
+ return TERN(LIB_INTERNAL_MAX31865,
+ max31865_0.temperature((uint16_t)raw),
+ max31865_0.temperature(MAX31865_SENSOR_OHMS_0, MAX31865_CALIBRATION_OHMS_0)
+ );
+ #else
+ return raw * 0.25;
+ #endif
#elif TEMP_SENSOR_0_IS_AD595
return TEMP_AD595(raw);
#elif TEMP_SENSOR_0_IS_AD8495
@@ -1742,7 +1769,14 @@ void Temperature::manage_heater() {
#if TEMP_SENSOR_1_IS_CUSTOM
return user_thermistor_to_deg_c(CTI_HOTEND_1, raw);
#elif TEMP_SENSOR_1_IS_MAX_TC
- return TERN(TEMP_SENSOR_1_IS_MAX31865, max31865_1.temperature(MAX31865_SENSOR_OHMS_1, MAX31865_CALIBRATION_OHMS_1), raw * 0.25);
+ #if TEMP_SENSOR_0_IS_MAX31865
+ return TERN(LIB_INTERNAL_MAX31865,
+ max31865_1.temperature((uint16_t)raw),
+ max31865_1.temperature(MAX31865_SENSOR_OHMS_1, MAX31865_CALIBRATION_OHMS_1)
+ );
+ #else
+ return raw * 0.25;
+ #endif
#elif TEMP_SENSOR_1_IS_AD595
return TEMP_AD595(raw);
#elif TEMP_SENSOR_1_IS_AD8495
@@ -1901,9 +1935,9 @@ void Temperature::manage_heater() {
#if TEMP_SENSOR_REDUNDANT_IS_CUSTOM
return user_thermistor_to_deg_c(CTI_REDUNDANT, raw);
#elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 0
- return TERN(TEMP_SENSOR_REDUNDANT_IS_MAX31865, max31865_0.temperature(MAX31865_SENSOR_OHMS_0, MAX31865_CALIBRATION_OHMS_0), raw * 0.25);
+ return TERN(TEMP_SENSOR_REDUNDANT_IS_MAX31865, max31865_0.temperature((uint16_t)raw), raw * 0.25);
#elif TEMP_SENSOR_REDUNDANT_IS_MAX_TC && TEMP_SENSOR_REDUNDANT_SOURCE == 1
- return TERN(TEMP_SENSOR_REDUNDANT_IS_MAX31865, max31865_1.temperature(MAX31865_SENSOR_OHMS_1, MAX31865_CALIBRATION_OHMS_1), raw * 0.25);
+ return TERN(TEMP_SENSOR_REDUNDANT_IS_MAX31865, max31865_1.temperature((uint16_t)raw), raw * 0.25);
#elif TEMP_SENSOR_REDUNDANT_IS_THERMISTOR
SCAN_THERMISTOR_TABLE(TEMPTABLE_REDUNDANT, TEMPTABLE_REDUNDANT_LEN);
#elif TEMP_SENSOR_REDUNDANT_IS_AD595
@@ -1936,6 +1970,7 @@ void Temperature::updateTemperaturesFromRawValues() {
TERN_(TEMP_SENSOR_0_IS_MAX_TC, temp_hotend[0].raw = READ_MAX_TC(0));
TERN_(TEMP_SENSOR_1_IS_MAX_TC, temp_hotend[1].raw = READ_MAX_TC(1));
TERN_(TEMP_SENSOR_REDUNDANT_IS_MAX_TC, temp_redundant.raw = READ_MAX_TC(TEMP_SENSOR_REDUNDANT_SOURCE));
+
#if HAS_HOTEND
HOTEND_LOOP() temp_hotend[e].celsius = analog_to_celsius_hotend(temp_hotend[e].raw, e);
#endif
@@ -2008,40 +2043,7 @@ void Temperature::updateTemperaturesFromRawValues() {
if (cutter.unitPower > 0 && COOLERCMP(temp_cooler.raw, maxtemp_raw_COOLER)) max_temp_error(H_COOLER);
if (COOLERCMP(mintemp_raw_COOLER, temp_cooler.raw)) min_temp_error(H_COOLER);
#endif
-}
-
-#if THERMO_SEPARATE_SPI
- template SoftSPI SPIclass::softSPI;
- SPIclass max_tc_spi;
-#endif
-
-// Init fans according to whether they're native PWM or Software PWM
-#ifdef BOARD_OPENDRAIN_MOSFETS
- #define _INIT_SOFT_FAN(P) OUT_WRITE_OD(P, FAN_INVERTING ? LOW : HIGH)
-#else
- #define _INIT_SOFT_FAN(P) OUT_WRITE(P, FAN_INVERTING ? LOW : HIGH)
-#endif
-#if ENABLED(FAN_SOFT_PWM)
- #define _INIT_FAN_PIN(P) _INIT_SOFT_FAN(P)
-#else
- #define _INIT_FAN_PIN(P) do{ if (PWM_PIN(P)) SET_PWM(P); else _INIT_SOFT_FAN(P); }while(0)
-#endif
-#if ENABLED(FAST_PWM_FAN)
- #define SET_FAST_PWM_FREQ(P) set_pwm_frequency(P, FAST_PWM_FAN_FREQUENCY)
-#else
- #define SET_FAST_PWM_FREQ(P) NOOP
-#endif
-#define INIT_FAN_PIN(P) do{ _INIT_FAN_PIN(P); SET_FAST_PWM_FREQ(P); }while(0)
-#if EXTRUDER_AUTO_FAN_SPEED != 255
- #define INIT_E_AUTO_FAN_PIN(P) do{ if (P == FAN1_PIN || P == FAN2_PIN) { SET_PWM(P); SET_FAST_PWM_FREQ(P); } else SET_OUTPUT(P); }while(0)
-#else
- #define INIT_E_AUTO_FAN_PIN(P) SET_OUTPUT(P)
-#endif
-#if CHAMBER_AUTO_FAN_SPEED != 255
- #define INIT_CHAMBER_AUTO_FAN_PIN(P) do{ if (P == FAN1_PIN || P == FAN2_PIN) { SET_PWM(P); SET_FAST_PWM_FREQ(P); } else SET_OUTPUT(P); }while(0)
-#else
- #define INIT_CHAMBER_AUTO_FAN_PIN(P) SET_OUTPUT(P)
-#endif
+} // Temperature::updateTemperaturesFromRawValues
/**
* Initialize the temperature manager
@@ -2070,50 +2072,47 @@ void Temperature::init() {
#endif
// Init (and disable) SPI thermocouples
- #if TEMP_SENSOR_IS_MAX(0, MAX6675) && PIN_EXISTS(MAX6675_CS)
- OUT_WRITE(MAX6675_CS_PIN, HIGH);
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX6675) && PIN_EXISTS(MAX6675_CS2)
- OUT_WRITE(MAX6675_CS2_PIN, HIGH);
- #endif
- #if TEMP_SENSOR_IS_MAX(0, MAX6675) && PIN_EXISTS(MAX31855_CS)
- OUT_WRITE(MAX31855_CS_PIN, HIGH);
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX6675) && PIN_EXISTS(MAX31855_CS2)
- OUT_WRITE(MAX31855_CS2_PIN, HIGH);
- #endif
- #if TEMP_SENSOR_IS_MAX(0, MAX6675) && PIN_EXISTS(MAX31865_CS)
- OUT_WRITE(MAX31865_CS_PIN, HIGH);
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX6675) && PIN_EXISTS(MAX31865_CS2)
- OUT_WRITE(MAX31865_CS2_PIN, HIGH);
- #endif
-
- #if HAS_MAX31865_TEMP
- #if TEMP_SENSOR_IS_MAX(0, MAX31865)
- max31865_0.begin(MAX31865_2WIRE); // MAX31865_2WIRE, MAX31865_3WIRE, MAX31865_4WIRE
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX31865)
- max31865_1.begin(MAX31865_2WIRE);
- #endif
- #endif
-
- #if HAS_MAX31855_TEMP
- #if TEMP_SENSOR_IS_MAX(0, MAX31855)
- max31855_0.begin(MAX31855);
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX31855)
- max31855_1.begin(MAX31855);
+ #if TEMP_SENSOR_IS_ANY_MAX_TC(0) && PIN_EXISTS(TEMP_0_CS)
+ OUT_WRITE(TEMP_0_CS_PIN, HIGH);
+ #endif
+ #if TEMP_SENSOR_IS_ANY_MAX_TC(1) && PIN_EXISTS(TEMP_1_CS)
+ OUT_WRITE(TEMP_1_CS_PIN, HIGH);
+ #endif
+
+ // Setup objects for library-based polling of MAX TCs
+ #if HAS_MAXTC_LIBRARIES
+ #define _MAX31865_WIRES(n) MAX31865_##n##WIRE
+ #define MAX31865_WIRES(n) _MAX31865_WIRES(n)
+
+ #if TEMP_SENSOR_IS_MAX(0, 6675) && HAS_MAX6675_LIBRARY
+ max6675_0.begin();
+ #elif TEMP_SENSOR_IS_MAX(0, 31855) && HAS_MAX31855_LIBRARY
+ max31855_0.begin();
+ #elif TEMP_SENSOR_IS_MAX(0, 31865)
+ max31865_0.begin(
+ MAX31865_WIRES(MAX31865_SENSOR_WIRES_0) // MAX31865_2WIRE, MAX31865_3WIRE, MAX31865_4WIRE
+ OPTARG(LIB_INTERNAL_MAX31865, MAX31865_SENSOR_OHMS_0, MAX31865_CALIBRATION_OHMS_0)
+ );
+ #if defined(LIB_INTERNAL_MAX31865) && ENABLED(MAX31865_50HZ_FILTER)
+ max31865_0.enable50HzFilter(1);
+ #endif
#endif
- #endif
- #if HAS_MAX6675_TEMP
- #if TEMP_SENSOR_IS_MAX(0, MAX6675)
- max6675_0.begin(MAX6675);
- #endif
- #if TEMP_SENSOR_IS_MAX(1, MAX6675)
- max6675_1.begin(MAX6675);
+ #if TEMP_SENSOR_IS_MAX(1, 6675) && HAS_MAX6675_LIBRARY
+ max6675_1.begin();
+ #elif TEMP_SENSOR_IS_MAX(1, 31855) && HAS_MAX31855_LIBRARY
+ max31855_1.begin();
+ #elif TEMP_SENSOR_IS_MAX(1, 31865)
+ max31865_1.begin(
+ MAX31865_WIRES(MAX31865_SENSOR_WIRES_1) // MAX31865_2WIRE, MAX31865_3WIRE, MAX31865_4WIRE
+ OPTARG(LIB_INTERNAL_MAX31865, MAX31865_SENSOR_OHMS_1, MAX31865_CALIBRATION_OHMS_1)
+ );
+ #if defined(LIB_INTERNAL_MAX31865) && ENABLED(MAX31865_50HZ_FILTER)
+ max31865_1.enable50HzFilter(1);
+ #endif
#endif
+ #undef MAX31865_WIRES
+ #undef _MAX31865_WIRES
#endif
#if MB(RUMBA)
@@ -2152,7 +2151,6 @@ void Temperature::init() {
OUT_WRITE(HEATER_0_PIN, HEATER_0_INVERTING);
#endif
#endif
-
#if HAS_HEATER_1
OUT_WRITE(HEATER_1_PIN, HEATER_1_INVERTING);
#endif
@@ -2219,7 +2217,9 @@ void Temperature::init() {
INIT_FAN_PIN(CONTROLLER_FAN_PIN);
#endif
- TERN_(THERMO_SEPARATE_SPI, max_tc_spi.init());
+ #if HAS_MAXTC_SW_SPI
+ max_tc_spi.init();
+ #endif
HAL_adc_init();
@@ -2318,11 +2318,7 @@ void Temperature::init() {
INIT_CHAMBER_AUTO_FAN_PIN(CHAMBER_AUTO_FAN_PIN);
#endif
- // Wait for temperature measurement to settle
- //delay(250);
-
#if HAS_HOTEND
-
#define _TEMP_MIN_E(NR) do{ \
const celsius_t tmin = _MAX(HEATER_##NR##_MINTEMP, TERN(TEMP_SENSOR_##NR##_IS_CUSTOM, 0, (int)pgm_read_word(&TEMPTABLE_##NR [TEMP_SENSOR_##NR##_MINTEMP_IND].celsius))); \
temp_range[NR].mintemp = tmin; \
@@ -2386,7 +2382,6 @@ void Temperature::init() {
#if _MINMAX_TEST(7, MAX)
_TEMP_MAX_E(7);
#endif
-
#endif // HAS_HOTEND
#if HAS_HEATED_BED
@@ -2520,9 +2515,8 @@ void Temperature::init() {
void Temperature::disable_all_heaters() {
+ // Disable autotemp, unpause and reset everything
TERN_(AUTOTEMP, planner.autotemp_enabled = false);
-
- // Unpause and reset everything
TERN_(PROBING_HEATERS_OFF, pause_heaters(false));
#if HAS_HOTEND
@@ -2558,8 +2552,6 @@ void Temperature::disable_all_heaters() {
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
- #include "printcounter.h"
-
bool Temperature::auto_job_over_threshold() {
#if HAS_HOTEND
HOTEND_LOOP() if (degTargetHotend(e) > (EXTRUDE_MINTEMP) / 2) return true;
@@ -2578,7 +2570,7 @@ void Temperature::disable_all_heaters() {
}
}
-#endif
+#endif // PRINTJOB_TIMER_AUTOSTART
#if ENABLED(PROBING_HEATERS_OFF)
@@ -2616,7 +2608,7 @@ void Temperature::disable_all_heaters() {
#endif
}
-#endif
+#endif // SINGLENOZZLE_STANDBY_TEMP || SINGLENOZZLE_STANDBY_FAN
#if HAS_MAX_TC
@@ -2624,113 +2616,114 @@ void Temperature::disable_all_heaters() {
#define THERMOCOUPLE_MAX_ERRORS 15
#endif
- int Temperature::read_max_tc(TERN_(HAS_MULTI_MAX_TC, const uint8_t hindex/*=0*/)) {
- #define MAX6675_HEAT_INTERVAL 250UL
+ /**
+ * @brief Read MAX Thermocouple temperature.
+ *
+ * Reads the thermocouple board via HW or SW SPI, using a library (LIB_USR_x) or raw SPI reads.
+ * Doesn't strictly return a temperature; returns an "ADC Value" (i.e. raw register content).
+ *
+ * @param hindex the hotend we're referencing (if MULTI_MAX_TC)
+ * @return integer representing the board's buffer, to be converted later if needed
+ */
+ int16_t Temperature::read_max_tc(TERN_(HAS_MULTI_MAX_TC, const uint8_t hindex/*=0*/)) {
+ #define MAXTC_HEAT_INTERVAL 250UL
- #if HAS_MAX31855_TEMP
- static uint32_t max_tc_temp = 2000;
- #define MAX_TC_ERROR_MASK 7
- #define MAX_TC_DISCARD_BITS 18
- #define MAX_TC_SPEED_BITS 3 // (_BV(SPR1)) // clock ÷ 64
- #elif HAS_MAX31865_TEMP
- static uint16_t max_tc_temp = 2000; // From datasheet 16 bits D15-D0
- #define MAX_TC_ERROR_MASK 1 // D0 Bit not used
+ #if HAS_MAX31855
+ #define MAX_TC_ERROR_MASK 7 // D2-0: SCV, SCG, OC
+ #define MAX_TC_DISCARD_BITS 18 // Data D31-18; sign bit D31
+ #define MAX_TC_SPEED_BITS 3 // ~1MHz
+ #elif HAS_MAX31865
+ #define MAX_TC_ERROR_MASK 1 // D0 Bit on fault only
#define MAX_TC_DISCARD_BITS 1 // Data is in D15-D1
- #define MAX_TC_SPEED_BITS 3 // (_BV(SPR1)) // clock ÷ 64
- #else
- static uint16_t max_tc_temp = 2000;
- #define MAX_TC_ERROR_MASK 4
- #define MAX_TC_DISCARD_BITS 3
- #define MAX_TC_SPEED_BITS 2 // (_BV(SPR0)) // clock ÷ 16
+ #define MAX_TC_SPEED_BITS 3 // ~1MHz
+ #else // MAX6675
+ #define MAX_TC_ERROR_MASK 3 // D2 only; 1 = open circuit
+ #define MAX_TC_DISCARD_BITS 3 // Data D15-D1
+ #define MAX_TC_SPEED_BITS 2 // ~2MHz
#endif
#if HAS_MULTI_MAX_TC
// Needed to return the correct temp when this is called between readings
- static celsius_t max_tc_temp_previous[MAX_TC_COUNT] = { 0 };
+ static int16_t max_tc_temp_previous[MAX_TC_COUNT] = { 0 };
#define THERMO_TEMP(I) max_tc_temp_previous[I]
#define THERMO_SEL(A,B) (hindex ? (B) : (A))
- #define MAX6675_WRITE(V) do{ switch (hindex) { case 1: WRITE(MAX6675_SS2_PIN, V); break; default: WRITE(MAX6675_SS_PIN, V); } }while(0)
- #define MAX6675_SET_OUTPUT() do{ switch (hindex) { case 1: SET_OUTPUT(MAX6675_SS2_PIN); break; default: SET_OUTPUT(MAX6675_SS_PIN); } }while(0)
+ #define MAXTC_CS_WRITE(V) do{ switch (hindex) { case 1: WRITE(TEMP_1_CS_PIN, V); break; default: WRITE(TEMP_0_CS_PIN, V); } }while(0)
#else
+ // When we have only 1 max tc, THERMO_SEL will pick the appropriate sensor
+ // variable, and MAXTC_*() macros will be hardcoded to the correct CS pin.
constexpr uint8_t hindex = 0;
#define THERMO_TEMP(I) max_tc_temp
- #if TEMP_SENSOR_IS_ANY_MAX_TC(1)
- #define THERMO_SEL(A,B) B
- #else
+ #if TEMP_SENSOR_IS_ANY_MAX_TC(0)
#define THERMO_SEL(A,B) A
- #endif
- #if TEMP_SENSOR_IS_MAX(0, MAX6675)
- #define MAX6675_WRITE(V) WRITE(MAX6675_SS_PIN, V)
- #define MAX6675_SET_OUTPUT() SET_OUTPUT(MAX6675_SS_PIN)
+ #define MAXTC_CS_WRITE(V) WRITE(TEMP_0_CS_PIN, V)
#else
- #define MAX6675_WRITE(V) WRITE(MAX6675_SS2_PIN, V)
- #define MAX6675_SET_OUTPUT() SET_OUTPUT(MAX6675_SS2_PIN)
+ #define THERMO_SEL(A,B) B
+ #define MAXTC_CS_WRITE(V) WRITE(TEMP_1_CS_PIN, V)
#endif
-
#endif
+ static TERN(HAS_MAX31855, uint32_t, uint16_t) max_tc_temp = THERMO_SEL(
+ TEMP_SENSOR_0_MAX_TC_TMAX,
+ TEMP_SENSOR_1_MAX_TC_TMAX
+ );
+
static uint8_t max_tc_errors[MAX_TC_COUNT] = { 0 };
+ static millis_t next_max_tc_ms[MAX_TC_COUNT] = { 0 };
// Return last-read value between readings
- static millis_t next_max_tc_ms[MAX_TC_COUNT] = { 0 };
millis_t ms = millis();
- if (PENDING(ms, next_max_tc_ms[hindex])) return int(THERMO_TEMP(hindex));
- next_max_tc_ms[hindex] = ms + MAX6675_HEAT_INTERVAL;
+ if (PENDING(ms, next_max_tc_ms[hindex]))
+ return (int16_t)THERMO_TEMP(hindex);
- //
- // TODO: spiBegin, spiRec and spiInit doesn't work when soft spi is used.
- //
- #if !THERMO_SEPARATE_SPI && NO_THERMO_TEMPS
- spiBegin();
- spiInit(MAX_TC_SPEED_BITS);
- #endif
+ next_max_tc_ms[hindex] = ms + MAXTC_HEAT_INTERVAL;
- #if NO_THERMO_TEMPS
- MAX6675_WRITE(LOW); // enable TT_MAX6675
- DELAY_NS(100); // Ensure 100ns delay
- #endif
+ #if !HAS_MAXTC_LIBRARIES
+ max_tc_temp = 0;
- max_tc_temp = 0;
+ #if !HAS_MAXTC_SW_SPI
+ // Initialize SPI using the default Hardware SPI bus.
+ // FIXME: spiBegin, spiRec and spiInit doesn't work when soft spi is used.
+ spiBegin();
+ spiInit(MAX_TC_SPEED_BITS);
+ #endif
+
+ MAXTC_CS_WRITE(LOW); // enable MAXTC
+ DELAY_NS(100); // Ensure 100ns delay
- // Read a big-endian temperature value
- #if NO_THERMO_TEMPS
+ // Read a big-endian temperature value without using a library
for (uint8_t i = sizeof(max_tc_temp); i--;) {
- max_tc_temp |= TERN(THERMO_SEPARATE_SPI, max_tc_spi.receive(), spiRec());
+ max_tc_temp |= TERN(HAS_MAXTC_SW_SPI, max_tc_spi.receive(), spiRec());
if (i > 0) max_tc_temp <<= 8; // shift left if not the last byte
}
- MAX6675_WRITE(HIGH); // disable TT_MAX6675
- #endif
- #if HAS_MAX31855_TEMP
- Adafruit_MAX31855 &max855ref = THERMO_SEL(max31855_0, max31855_1);
- max_tc_temp = max855ref.readRaw32();
- #endif
-
- #if HAS_MAX31865_TEMP
- Adafruit_MAX31865 &max865ref = THERMO_SEL(max31865_0, max31865_1);
- #if ENABLED(LIB_USR_MAX31865)
- max_tc_temp = max865ref.readRTD_with_Fault();
+ MAXTC_CS_WRITE(HIGH); // disable MAXTC
+ #else
+ #if HAS_MAX6675_LIBRARY
+ MAX6675 &max6675ref = THERMO_SEL(max6675_0, max6675_1);
+ max_tc_temp = max6675ref.readRaw16();
#endif
- #endif
- #if HAS_MAX6675_TEMP
- MAX6675 &max6675ref = THERMO_SEL(max6675_0, max6675_1);
- max_tc_temp = max6675ref.readRaw16();
- #endif
+ #if HAS_MAX31855_LIBRARY
+ MAX31855 &max855ref = THERMO_SEL(max31855_0, max31855_1);
+ max_tc_temp = max855ref.readRaw32();
+ #endif
- #if ENABLED(LIB_ADAFRUIT_MAX31865)
- const uint8_t fault_31865 = max865ref.readFault() & 0x3FU;
+ #if HAS_MAX31865
+ MAX31865 &max865ref = THERMO_SEL(max31865_0, max31865_1);
+ max_tc_temp = TERN(LIB_INTERNAL_MAX31865, max865ref.readRaw(), max865ref.readRTD_with_Fault());
+ #endif
#endif
- if (DISABLED(IGNORE_THERMOCOUPLE_ERRORS)
- && TERN(LIB_ADAFRUIT_MAX31865, fault_31865, (max_tc_temp & MAX_TC_ERROR_MASK))
- ) {
+ // Handle an error. If there have been more than THERMOCOUPLE_MAX_ERRORS, send an error over serial.
+ // Either way, return the TMAX for the thermocouple to trigger a max_temp_error()
+ if (max_tc_temp & MAX_TC_ERROR_MASK) {
max_tc_errors[hindex]++;
+
if (max_tc_errors[hindex] > THERMOCOUPLE_MAX_ERRORS) {
SERIAL_ERROR_START();
SERIAL_ECHOPGM("Temp measurement error! ");
- #if MAX_TC_ERROR_MASK == 7
- SERIAL_ECHOPGM("MAX31855 Fault : (", max_tc_temp & 0x7, ") >> ");
+ #if HAS_MAX31855
+ SERIAL_ECHOPAIR("MAX31855 Fault: (", max_tc_temp & 0x7, ") >> ");
if (max_tc_temp & 0x1)
SERIAL_ECHOLNPGM("Open Circuit");
else if (max_tc_temp & 0x2)
@@ -2738,59 +2731,46 @@ void Temperature::disable_all_heaters() {
else if (max_tc_temp & 0x4)
SERIAL_ECHOLNPGM("Short to VCC");
#elif HAS_MAX31865
- #if ENABLED(LIB_USR_MAX31865)
- // At the present time we do not have the ability to set the MAX31865 HIGH threshold
- // or thr LOW threshold, so no need to check for them, zero these bits out
- const uint8_t fault_31865 = max865ref.readFault() & 0x3FU;
- #endif
+ const uint8_t fault_31865 = max865ref.readFault();
max865ref.clearFault();
if (fault_31865) {
SERIAL_EOL();
- SERIAL_ECHOLNPAIR("\nMAX31865 Fault :(", fault_31865, ") >>");
+ SERIAL_ECHOLNPAIR("\nMAX31865 Fault: (", fault_31865, ") >>");
if (fault_31865 & MAX31865_FAULT_HIGHTHRESH)
SERIAL_ECHOLNPGM("RTD High Threshold");
if (fault_31865 & MAX31865_FAULT_LOWTHRESH)
SERIAL_ECHOLNPGM("RTD Low Threshold");
if (fault_31865 & MAX31865_FAULT_REFINLOW)
- SERIAL_ECHOLNPGM("REFIN- > 0.85 x Bias");
+ SERIAL_ECHOLNPGM("REFIN- > 0.85 x V bias");
if (fault_31865 & MAX31865_FAULT_REFINHIGH)
- SERIAL_ECHOLNPGM("REFIN- < 0.85 x Bias - FORCE- open");
+ SERIAL_ECHOLNPGM("REFIN- < 0.85 x V bias (FORCE- open)");
if (fault_31865 & MAX31865_FAULT_RTDINLOW)
- SERIAL_ECHOLNPGM("REFIN- < 0.85 x Bias - FORCE- open");
+ SERIAL_ECHOLNPGM("REFIN- < 0.85 x V bias (FORCE- open)");
if (fault_31865 & MAX31865_FAULT_OVUV)
SERIAL_ECHOLNPGM("Under/Over voltage");
}
- #else
- SERIAL_ECHOLNPGM("MAX6675 Open Circuit");
+ #else // MAX6675
+ SERIAL_ECHOLNPGM("MAX6675 Fault: Open Circuit");
#endif
- // Thermocouple open
- max_tc_temp = 4 * THERMO_SEL(TEMP_SENSOR_0_MAX_TC_TMAX, TEMP_SENSOR_1_MAX_TC_TMAX);
+ // Set thermocouple above max temperature (TMAX)
+ max_tc_temp = THERMO_SEL(TEMP_SENSOR_0_MAX_TC_TMAX, TEMP_SENSOR_1_MAX_TC_TMAX) << (MAX_TC_DISCARD_BITS + 1);
}
- else
- max_tc_temp >>= MAX_TC_DISCARD_BITS;
}
else {
- max_tc_temp >>= MAX_TC_DISCARD_BITS;
- max_tc_errors[hindex] = 0;
+ max_tc_errors[hindex] = 0; // No error bit, reset error count
}
- #if HAS_MAX31855
- if (max_tc_temp & 0x00002000) max_tc_temp |= 0xFFFFC000; // Support negative temperature
- #endif
+ max_tc_temp >>= MAX_TC_DISCARD_BITS;
- // Return the RTD resistance for MAX31865 for display in SHOW_TEMP_ADC_VALUES
- #if HAS_MAX31865_TEMP
- #if ENABLED(LIB_ADAFRUIT_MAX31865)
- max_tc_temp = (uint32_t(max865ref.readRTD()) * THERMO_SEL(MAX31865_CALIBRATION_OHMS_0, MAX31865_CALIBRATION_OHMS_1)) >> 16;
- #elif ENABLED(LIB_USR_MAX31865)
- max_tc_temp = (uint32_t(max_tc_temp) * THERMO_SEL(MAX31865_CALIBRATION_OHMS_0, MAX31865_CALIBRATION_OHMS_1)) >> 16;
- #endif
+ #if HAS_MAX31855
+ // Support negative temperature for MAX38155
+ if (max_tc_temp & 0x00002000) max_tc_temp |= 0xFFFFC000;
#endif
THERMO_TEMP(hindex) = max_tc_temp;
- return int(max_tc_temp);
+ return (int16_t)max_tc_temp;
}
#endif // HAS_MAX_TC
@@ -2815,16 +2795,16 @@ void Temperature::update_raw_temperatures() {
temp_redundant.update();
#endif
- TERN_(HAS_TEMP_ADC_2, temp_hotend[2].update());
- TERN_(HAS_TEMP_ADC_3, temp_hotend[3].update());
- TERN_(HAS_TEMP_ADC_4, temp_hotend[4].update());
- TERN_(HAS_TEMP_ADC_5, temp_hotend[5].update());
- TERN_(HAS_TEMP_ADC_6, temp_hotend[6].update());
- TERN_(HAS_TEMP_ADC_7, temp_hotend[7].update());
- TERN_(HAS_TEMP_ADC_BED, temp_bed.update());
+ TERN_(HAS_TEMP_ADC_2, temp_hotend[2].update());
+ TERN_(HAS_TEMP_ADC_3, temp_hotend[3].update());
+ TERN_(HAS_TEMP_ADC_4, temp_hotend[4].update());
+ TERN_(HAS_TEMP_ADC_5, temp_hotend[5].update());
+ TERN_(HAS_TEMP_ADC_6, temp_hotend[6].update());
+ TERN_(HAS_TEMP_ADC_7, temp_hotend[7].update());
+ TERN_(HAS_TEMP_ADC_BED, temp_bed.update());
TERN_(HAS_TEMP_ADC_CHAMBER, temp_chamber.update());
- TERN_(HAS_TEMP_ADC_PROBE, temp_probe.update());
- TERN_(HAS_TEMP_ADC_COOLER, temp_cooler.update());
+ TERN_(HAS_TEMP_ADC_PROBE, temp_probe.update());
+ TERN_(HAS_TEMP_ADC_COOLER, temp_cooler.update());
TERN_(HAS_JOY_ADC_X, joystick.x.update());
TERN_(HAS_JOY_ADC_Y, joystick.y.update());
@@ -3465,7 +3445,7 @@ void Temperature::isr() {
SERIAL_PRINT(t, SFP);
#if ENABLED(SHOW_TEMP_ADC_VALUES)
// Temperature MAX SPI boards do not have an OVERSAMPLENR defined
- SERIAL_ECHOPAIR(" (", TERN(NO_THERMO_TEMPS, false, k == 'T') ? r : r * RECIPROCAL(OVERSAMPLENR));
+ SERIAL_ECHOPAIR(" (", TERN(HAS_MAXTC_LIBRARIES, k == 'T', false) ? r : r * RECIPROCAL(OVERSAMPLENR));
SERIAL_CHAR(')');
#endif
delay(2);
diff --git a/Marlin/src/module/temperature.h b/Marlin/src/module/temperature.h
index 3a8c506a5db0..26c1dca8afb8 100644
--- a/Marlin/src/module/temperature.h
+++ b/Marlin/src/module/temperature.h
@@ -428,6 +428,15 @@ class Temperature {
static heater_idle_t heater_idle[NR_HEATER_IDLE];
+ #endif // HEATER_IDLE_TIMER
+
+ #if HAS_ADC_BUTTONS
+ static uint32_t current_ADCKey_raw;
+ static uint16_t ADCKey_count;
+ #endif
+
+ #if ENABLED(PID_EXTRUSION_SCALING)
+ static int16_t lpq_len;
#endif
private:
@@ -486,15 +495,6 @@ class Temperature {
#endif
public:
- #if HAS_ADC_BUTTONS
- static uint32_t current_ADCKey_raw;
- static uint16_t ADCKey_count;
- #endif
-
- #if ENABLED(PID_EXTRUSION_SCALING)
- static int16_t lpq_len;
- #endif
-
/**
* Instance Methods
*/
@@ -915,7 +915,7 @@ class Temperature {
#else
#define READ_MAX_TC(N) read_max_tc()
#endif
- static int read_max_tc(TERN_(HAS_MULTI_MAX_TC, const uint8_t hindex=0));
+ static int16_t read_max_tc(TERN_(HAS_MULTI_MAX_TC, const uint8_t hindex=0));
#endif
static void checkExtruderAutoFans();
diff --git a/Marlin/src/pins/linux/pins_RAMPS_LINUX.h b/Marlin/src/pins/linux/pins_RAMPS_LINUX.h
index ab1446f07c9f..568086e066f1 100644
--- a/Marlin/src/pins/linux/pins_RAMPS_LINUX.h
+++ b/Marlin/src/pins/linux/pins_RAMPS_LINUX.h
@@ -133,11 +133,11 @@
#define TEMP_1_PIN 1 // Analog Input
#define TEMP_BED_PIN 2 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h b/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h
index 066c65be3af8..f7e566e2d620 100644
--- a/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h
+++ b/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h
@@ -73,6 +73,19 @@
#endif
#endif
+// CS, MISO, MOSI, and SCK for MAX Thermocouple SPI
+#if HAS_MAX_TC
+ //#define TEMP_0_CS_PIN P...
+ //#define TEMP_0_MISO_PIN P...
+ //#define TEMP_0_MOSI_PIN P...
+ //#define TEMP_0_SCK_PIN P...
+
+ //#define TEMP_1_CS_PIN P...
+ //#define TEMP_1_MISO_PIN P...
+ //#define TEMP_1_MOSI_PIN P...
+ //#define TEMP_1_SCK_PIN P...
+#endif
+
//
// Heaters / Fans
//
diff --git a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
index 83fcf36e4e1f..c25f676a08b1 100644
--- a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
+++ b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
@@ -248,8 +248,8 @@
#define PS_ON_PIN P2_12 // (12)
-#if !defined(MAX6675_SS_PIN) && DISABLED(USE_ZMAX_PLUG)
- #define MAX6675_SS_PIN P1_28
+#if !defined(TEMP_0_CS_PIN) && DISABLED(USE_ZMAX_PLUG)
+ #define TEMP_0_CS_PIN P1_28
#endif
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENA_PIN)
diff --git a/Marlin/src/pins/mega/pins_MALYAN_M180.h b/Marlin/src/pins/mega/pins_MALYAN_M180.h
index e244d294f1c6..19095a53799f 100644
--- a/Marlin/src/pins/mega/pins_MALYAN_M180.h
+++ b/Marlin/src/pins/mega/pins_MALYAN_M180.h
@@ -72,17 +72,17 @@
#define TEMP_BED_PIN 15 // Analog Input
// Extruder thermocouples 0 and 1 are read out by two separate ICs using
-// SPI for Max6675 Thermocouple
+// SPI for MAX Thermocouple
// Uses a separate SPI bus
-#define THERMO_SCK_PIN 78 // E2 - SCK
-#define THERMO_DO_PIN 3 // E5 - DO
-#define THERMO_CS1_PIN 5 // E3 - CS0
-#define THERMO_CS2_PIN 2 // E4 - CS1
+#define TEMP_0_CS_PIN 5 // E3 - CS0
+#define TEMP_0_SCK_PIN 78 // E2 - SCK
+#define TEMP_0_MISO_PIN 3 // E5 - MISO
+//#define TEMP_0_MOSI_PIN ... // For MAX31865
-#define MAX6675_SS_PIN THERMO_CS1_PIN
-#define MAX6675_SS2_PIN THERMO_CS2_PIN
-#define MAX6675_SCK_PIN THERMO_SCK_PIN
-#define MAX6675_DO_PIN THERMO_DO_PIN
+#define TEMP_1_CS_PIN 2 // E4 - CS1
+#define TEMP_1_SCK_PIN TEMP_0_SCK_PIN
+#define TEMP_1_MISO_PIN TEMP_0_MISO_PIN
+//#define TEMP_1_MOSI_PIN TEMP_0_MOSI_PIN
//
// Heaters / Fans
diff --git a/Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h b/Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h
index 2531f10a7ae3..aea05134a87c 100644
--- a/Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h
+++ b/Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h
@@ -125,7 +125,7 @@
// K7 - 69 / ADC15 - 15
#define TEMP_BED_PIN 15
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
// Uses a separate SPI bus
//
// 3 E5 DO (SO)
@@ -133,15 +133,15 @@
// 2 E4 CS2
// 78 E2 SCK
//
-#define THERMO_SCK_PIN 78 // E2
-#define THERMO_DO_PIN 3 // E5
-#define THERMO_CS1_PIN 5 // E3
-#define THERMO_CS2_PIN 2 // E4
-
-#define MAX6675_SS_PIN THERMO_CS1_PIN
-#define MAX6675_SS2_PIN THERMO_CS2_PIN
-#define MAX6675_SCK_PIN THERMO_SCK_PIN
-#define MAX6675_DO_PIN THERMO_DO_PIN
+#define TEMP_0_CS_PIN 5 // E3
+#define TEMP_0_SCK_PIN 78 // E2
+#define TEMP_0_MISO_PIN 3 // E5
+//#define TEMP_0_MOSI_PIN ... // For MAX31865
+
+#define TEMP_1_CS_PIN 2 // E4
+#define TEMP_1_SCK_PIN TEMP_0_SCK_PIN
+#define TEMP_1_MISO_PIN TEMP_0_MISO_PIN
+//#define TEMP_1_MOSI_PIN TEMP_0_MOSI_PIN
//
// Augmentation for auto-assigning plugs
diff --git a/Marlin/src/pins/mega/pins_PICA.h b/Marlin/src/pins/mega/pins_PICA.h
index 41afe5d891b3..47c101711c4f 100644
--- a/Marlin/src/pins/mega/pins_PICA.h
+++ b/Marlin/src/pins/mega/pins_PICA.h
@@ -118,11 +118,11 @@
#define SSR_PIN 6
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/pinsDebug_list.h b/Marlin/src/pins/pinsDebug_list.h
index 1ab7188b701a..8b1cad3a7c97 100644
--- a/Marlin/src/pins/pinsDebug_list.h
+++ b/Marlin/src/pins/pinsDebug_list.h
@@ -760,17 +760,29 @@
#if PIN_EXISTS(LED_RED)
REPORT_NAME_DIGITAL(__LINE__, LED_RED_PIN)
#endif
-#if PIN_EXISTS(MAX6675_DO)
- REPORT_NAME_DIGITAL(__LINE__, MAX6675_DO_PIN)
+#if PIN_EXISTS(TEMP_0_CS)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_0_CS_PIN)
#endif
-#if PIN_EXISTS(MAX6675_SCK)
- REPORT_NAME_DIGITAL(__LINE__, MAX6675_SCK_PIN)
+#if PIN_EXISTS(TEMP_0_SCK)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_0_SCK_PIN)
#endif
-#if PIN_EXISTS(MAX6675_SS)
- REPORT_NAME_DIGITAL(__LINE__, MAX6675_SS_PIN)
+#if PIN_EXISTS(TEMP_0_MOSI)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_0_MOSI_PIN)
#endif
-#if PIN_EXISTS(MAX6675_SS2)
- REPORT_NAME_DIGITAL(__LINE__, MAX6675_SS2_PIN)
+#if PIN_EXISTS(TEMP_0_MISO)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_0_MISO_PIN)
+#endif
+#if PIN_EXISTS(TEMP_1_CS)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_1_CS_PIN)
+#endif
+#if PIN_EXISTS(TEMP_1_SCK)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_1_SCK_PIN)
+#endif
+#if PIN_EXISTS(TEMP_1_MOSI)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_1_MOSI_PIN)
+#endif
+#if PIN_EXISTS(TEMP_1_MISO)
+ REPORT_NAME_DIGITAL(__LINE__, TEMP_1_MISO_PIN)
#endif
#if PIN_EXISTS(MAX7219_CLK)
REPORT_NAME_DIGITAL(__LINE__, MAX7219_CLK_PIN)
@@ -1010,18 +1022,6 @@
#if PIN_EXISTS(SUICIDE)
REPORT_NAME_DIGITAL(__LINE__, SUICIDE_PIN)
#endif
-#if PIN_EXISTS(THERMO_CS1)
- REPORT_NAME_DIGITAL(__LINE__, THERMO_CS1_PIN)
-#endif
-#if PIN_EXISTS(THERMO_CS2)
- REPORT_NAME_DIGITAL(__LINE__, THERMO_CS2_PIN)
-#endif
-#if PIN_EXISTS(THERMO_DO)
- REPORT_NAME_DIGITAL(__LINE__, THERMO_DO_PIN)
-#endif
-#if PIN_EXISTS(THERMO_SCK)
- REPORT_NAME_DIGITAL(__LINE__, THERMO_SCK_PIN)
-#endif
#if PIN_EXISTS(TLC_BLANK)
REPORT_NAME_DIGITAL(__LINE__, TLC_BLANK_PIN)
#endif
diff --git a/Marlin/src/pins/rambo/pins_RAMBO.h b/Marlin/src/pins/rambo/pins_RAMBO.h
index 5d6f9c1fd09d..f2d34dc00d79 100644
--- a/Marlin/src/pins/rambo/pins_RAMBO.h
+++ b/Marlin/src/pins/rambo/pins_RAMBO.h
@@ -171,10 +171,10 @@
#define SPINDLE_DIR_PIN 32
//
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
//
-#ifndef MAX6675_SS_PIN
- #define MAX6675_SS_PIN 32 // SPINDLE_DIR_PIN / STAT_LED_BLUE_PIN
+#ifndef TEMP_0_CS_PIN
+ #define TEMP_0_CS_PIN 32 // SPINDLE_DIR_PIN / STAT_LED_BLUE_PIN
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR.h b/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR.h
index 383501caaaf8..34a4ceb27d16 100644
--- a/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR.h
+++ b/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR.h
@@ -114,11 +114,11 @@
#define TEMP_1_PIN 15 // Analog Input
#define TEMP_BED_PIN 14 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h b/Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h
index ac0b7428f498..5f645e5d957a 100644
--- a/Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h
+++ b/Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h
@@ -111,11 +111,11 @@
#define TEMP_1_PIN 15 // Analog Input
#define TEMP_BED_PIN 3 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h b/Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h
index 76a9fbe62804..c953cff3d066 100644
--- a/Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h
+++ b/Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h
@@ -111,11 +111,11 @@
#define TEMP_1_PIN 15 // Analog Input
#define TEMP_BED_PIN 14 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_RAMPS.h b/Marlin/src/pins/ramps/pins_RAMPS.h
index c2d4dbeb3f81..b13b5e72a0a3 100644
--- a/Marlin/src/pins/ramps/pins_RAMPS.h
+++ b/Marlin/src/pins/ramps/pins_RAMPS.h
@@ -167,10 +167,10 @@
#endif
//
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
//
-#ifndef MAX6675_SS_PIN
- #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card (SDSS) or 49 (SD_DETECT_PIN)
+#ifndef TEMP_0_CS_PIN
+ #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card (SDSS) or 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_RAMPS_OLD.h b/Marlin/src/pins/ramps/pins_RAMPS_OLD.h
index a43ee3c6ca5a..974766623594 100644
--- a/Marlin/src/pins/ramps/pins_RAMPS_OLD.h
+++ b/Marlin/src/pins/ramps/pins_RAMPS_OLD.h
@@ -74,11 +74,11 @@
#define TEMP_0_PIN 2 // Analog Input
#define TEMP_BED_PIN 1 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_RIGIDBOARD.h b/Marlin/src/pins/ramps/pins_RIGIDBOARD.h
index 345c51d5de59..203af5e08180 100644
--- a/Marlin/src/pins/ramps/pins_RIGIDBOARD.h
+++ b/Marlin/src/pins/ramps/pins_RIGIDBOARD.h
@@ -75,12 +75,12 @@
#define TEMP_1_PIN 13 // Analog Input
#define TEMP_BED_PIN 15 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
-#undef MAX6675_SS_PIN
+// SPI for MAX Thermocouple
+#undef TEMP_0_CS_PIN
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53 // Don't use pin 53 if there is even the remote possibility of using Display/SD card
+ #define TEMP_0_CS_PIN 53 // Don't use pin 53 if there is even the remote possibility of using Display/SD card
#else
- #define MAX6675_SS_PIN 49 // Don't use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
+ #define TEMP_0_CS_PIN 49 // Don't use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_TENLOG_D3_HERO.h b/Marlin/src/pins/ramps/pins_TENLOG_D3_HERO.h
index 53e419af00cc..de8db60847f5 100644
--- a/Marlin/src/pins/ramps/pins_TENLOG_D3_HERO.h
+++ b/Marlin/src/pins/ramps/pins_TENLOG_D3_HERO.h
@@ -123,11 +123,11 @@
#define TEMP_1_PIN 15 // Analog Input
#define TEMP_BED_PIN 14 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN -1 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN -1 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN -1 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN -1 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/ramps/pins_TT_OSCAR.h b/Marlin/src/pins/ramps/pins_TT_OSCAR.h
index aba8f80e6107..57a9a560d35b 100644
--- a/Marlin/src/pins/ramps/pins_TT_OSCAR.h
+++ b/Marlin/src/pins/ramps/pins_TT_OSCAR.h
@@ -181,11 +181,11 @@
#define TEMP_4_PIN 12
#endif
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
//#if DISABLED(SDSUPPORT)
-// #define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card
+// #define TEMP_0_CS_PIN 66 // Don't use 53 if using Display/SD card
//#else
-// #define MAX6675_SS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
+// #define TEMP_0_CS_PIN 66 // Don't use 49 (SD_DETECT_PIN)
//#endif
//
diff --git a/Marlin/src/pins/sam/pins_DUE3DOM.h b/Marlin/src/pins/sam/pins_DUE3DOM.h
index de3cb33e8de3..81eca3e4b14a 100644
--- a/Marlin/src/pins/sam/pins_DUE3DOM.h
+++ b/Marlin/src/pins/sam/pins_DUE3DOM.h
@@ -82,11 +82,11 @@
#define TEMP_2_PIN 5 // Analog Input (unused)
#define TEMP_BED_PIN 1 // Analog Input (BED thermistor)
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN -1
+ #define TEMP_0_CS_PIN -1
#else
- #define MAX6675_SS_PIN -1
+ #define TEMP_0_CS_PIN -1
#endif
//
diff --git a/Marlin/src/pins/sam/pins_DUE3DOM_MINI.h b/Marlin/src/pins/sam/pins_DUE3DOM_MINI.h
index c52199a54dc5..bc0d29b00a02 100644
--- a/Marlin/src/pins/sam/pins_DUE3DOM_MINI.h
+++ b/Marlin/src/pins/sam/pins_DUE3DOM_MINI.h
@@ -71,11 +71,11 @@
#define TEMP_2_PIN 5 // Analog Input (OnBoard thermistor beta 3950)
#define TEMP_BED_PIN 1 // Analog Input (BED thermistor)
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53
+ #define TEMP_0_CS_PIN 53
#else
- #define MAX6675_SS_PIN 53
+ #define TEMP_0_CS_PIN 53
#endif
//
diff --git a/Marlin/src/pins/sam/pins_RADDS.h b/Marlin/src/pins/sam/pins_RADDS.h
index 7b0ec5ab68e8..7a865b4ad870 100644
--- a/Marlin/src/pins/sam/pins_RADDS.h
+++ b/Marlin/src/pins/sam/pins_RADDS.h
@@ -179,11 +179,11 @@
#define TEMP_4_PIN 5 // dummy so will compile when PINS_DEBUGGING is enabled
#define TEMP_BED_PIN 4 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53
+ #define TEMP_0_CS_PIN 53
#else
- #define MAX6675_SS_PIN 49
+ #define TEMP_0_CS_PIN 49
#endif
//
diff --git a/Marlin/src/pins/sam/pins_RAMPS_DUO.h b/Marlin/src/pins/sam/pins_RAMPS_DUO.h
index b1a6680c506c..5b2b2f0b6615 100644
--- a/Marlin/src/pins/sam/pins_RAMPS_DUO.h
+++ b/Marlin/src/pins/sam/pins_RAMPS_DUO.h
@@ -60,12 +60,12 @@
#undef TEMP_BED_PIN
#define TEMP_BED_PIN 10 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
-#undef MAX6675_SS_PIN
+// SPI for MAX Thermocouple
+#undef TEMP_0_CS_PIN
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 69 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 69 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 69 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 69 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h b/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h
index e4c53530f7b0..30f209ad3713 100644
--- a/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h
+++ b/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h
@@ -109,11 +109,11 @@
#define TEMP_2_PIN 3 // Analog Input
#define TEMP_BED_PIN 0 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53
+ #define TEMP_0_CS_PIN 53
#else
- #define MAX6675_SS_PIN 49
+ #define TEMP_0_CS_PIN 49
#endif
//
diff --git a/Marlin/src/pins/sam/pins_RAMPS_SMART.h b/Marlin/src/pins/sam/pins_RAMPS_SMART.h
index 3882dfb94420..96d0c9e1cc9a 100644
--- a/Marlin/src/pins/sam/pins_RAMPS_SMART.h
+++ b/Marlin/src/pins/sam/pins_RAMPS_SMART.h
@@ -94,12 +94,12 @@
#undef TEMP_BED_PIN
#define TEMP_BED_PIN 11 // Analog Input
-// SPI for Max6675 or Max31855 Thermocouple
-#undef MAX6675_SS_PIN
+// SPI for MAX Thermocouple
+#undef TEMP_0_CS_PIN
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 67 // Don't use 53 if using Display/SD card
+ #define TEMP_0_CS_PIN 67 // Don't use 53 if using Display/SD card
#else
- #define MAX6675_SS_PIN 67 // Don't use 49 (SD_DETECT_PIN)
+ #define TEMP_0_CS_PIN 67 // Don't use 49 (SD_DETECT_PIN)
#endif
//
diff --git a/Marlin/src/pins/sam/pins_RURAMPS4D_11.h b/Marlin/src/pins/sam/pins_RURAMPS4D_11.h
index a52af48e1122..b21742891152 100644
--- a/Marlin/src/pins/sam/pins_RURAMPS4D_11.h
+++ b/Marlin/src/pins/sam/pins_RURAMPS4D_11.h
@@ -156,12 +156,12 @@
#define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support)
#endif
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
/*
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53
+ #define TEMP_0_CS_PIN 53
#else
- #define MAX6675_SS_PIN 49
+ #define TEMP_0_CS_PIN 49
#endif
*/
diff --git a/Marlin/src/pins/sam/pins_RURAMPS4D_13.h b/Marlin/src/pins/sam/pins_RURAMPS4D_13.h
index 37ebb567a699..700288690817 100644
--- a/Marlin/src/pins/sam/pins_RURAMPS4D_13.h
+++ b/Marlin/src/pins/sam/pins_RURAMPS4D_13.h
@@ -142,12 +142,12 @@
#define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support)
#endif
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
/*
#if DISABLED(SDSUPPORT)
- #define MAX6675_SS_PIN 53
+ #define TEMP_0_CS_PIN 53
#else
- #define MAX6675_SS_PIN 49
+ #define TEMP_0_CS_PIN 49
#endif
*/
diff --git a/Marlin/src/pins/sam/pins_ULTRATRONICS_PRO.h b/Marlin/src/pins/sam/pins_ULTRATRONICS_PRO.h
index e567b0f5e11d..a655d0121c84 100644
--- a/Marlin/src/pins/sam/pins_ULTRATRONICS_PRO.h
+++ b/Marlin/src/pins/sam/pins_ULTRATRONICS_PRO.h
@@ -149,12 +149,11 @@
#define SD_MISO_PIN 74
#define SD_MOSI_PIN 75
-// SPI for Max6675 or Max31855 Thermocouple
-#define MAX6675_SS_PIN 65
-#define MAX31855_SS0 65
-#define MAX31855_SS1 52
-#define MAX31855_SS2 50
-#define MAX31855_SS3 51
+// SPI for MAX Thermocouple
+#define TEMP_0_CS_PIN 65
+#define TEMP_1_CS_PIN 52
+#define TEMP_2_CS_PIN 50
+#define TEMP_3_CS_PIN 51
#define ENC424_SS 61
diff --git a/Marlin/src/pins/stm32f1/pins_MINGDA_MPX_ARM_MINI.h b/Marlin/src/pins/stm32f1/pins_MINGDA_MPX_ARM_MINI.h
index 429cf14ac5b8..179c04a3045c 100644
--- a/Marlin/src/pins/stm32f1/pins_MINGDA_MPX_ARM_MINI.h
+++ b/Marlin/src/pins/stm32f1/pins_MINGDA_MPX_ARM_MINI.h
@@ -100,10 +100,10 @@
//#define TEMP_0_PIN PB3 // E0 K+
#define TEMP_BED_PIN PF7 // THERM_BED
-#define MAX6675_SS_PIN PB5
-#define MAX6675_SCK_PIN PB3
-#define MAX6675_DO_PIN PB4
-#define MAX6675_MOSI_PIN PA14
+#define TEMP_0_CS_PIN PB5
+#define TEMP_0_SCK_PIN PB3
+#define TEMP_0_MISO_PIN PB4
+#define TEMP_0_MOSI_PIN PA14
//
// Heaters / Fans
diff --git a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN.h b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN.h
index b9f1074c7aa4..8da4dcc9de6c 100644
--- a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN.h
+++ b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN.h
@@ -121,8 +121,8 @@
//
// Thermocouples
//
-//#define MAX6675_SS_PIN PE5 // TC1 - CS1
-//#define MAX6675_SS_PIN PE6 // TC2 - CS2
+//#define TEMP_0_CS_PIN PE5 // TC1 - CS1
+//#define TEMP_0_CS_PIN PE6 // TC2 - CS2
//
// Filament runout sensor
diff --git a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO.h b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO.h
index ea3a7a1eea8e..0e2aee9e9971 100644
--- a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO.h
+++ b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO.h
@@ -124,8 +124,8 @@
//
// Thermocouples
//
-//#define MAX6675_SS_PIN PE5 // TC1 - CS1
-//#define MAX6675_SS_PIN PE6 // TC2 - CS2
+//#define TEMP_0_CS_PIN PE5 // TC1 - CS1
+//#define TEMP_0_CS_PIN PE6 // TC2 - CS2
//
// Misc. Functions
diff --git a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h
index 6ef3a0804384..3a203aab4978 100644
--- a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h
+++ b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h
@@ -188,8 +188,8 @@
//
// Thermocouples
//
-//#define MAX6675_SS_PIN PE5 // TC1 - CS1
-//#define MAX6675_SS_PIN PE6 // TC2 - CS2
+//#define TEMP_0_CS_PIN PE5 // TC1 - CS1
+//#define TEMP_0_CS_PIN PE6 // TC2 - CS2
//
// Misc. Functions
diff --git a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h
index b56971c7a353..129b640d9774 100644
--- a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h
+++ b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h
@@ -175,8 +175,8 @@
/**
* Note: MKS Robin Pro board is using SPI2 interface. Make sure your stm32duino library is configured accordingly
*/
-//#define MAX6675_SS_PIN PE5 // TC1 - CS1
-//#define MAX6675_SS_PIN PF11 // TC2 - CS2
+//#define TEMP_0_CS_PIN PE5 // TC1 - CS1
+//#define TEMP_0_CS_PIN PF11 // TC2 - CS2
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PG11 // PW_OFF
diff --git a/Marlin/src/pins/stm32f4/pins_BTT_GTR_V1_0.h b/Marlin/src/pins/stm32f4/pins_BTT_GTR_V1_0.h
index 4438ed63acc4..3151a38ae8f9 100644
--- a/Marlin/src/pins/stm32f4/pins_BTT_GTR_V1_0.h
+++ b/Marlin/src/pins/stm32f4/pins_BTT_GTR_V1_0.h
@@ -298,19 +298,19 @@
#define TEMP_BED_PIN PC0 // T0 <-> Bed
-// SPI for Max6675 or Max31855 Thermocouple
+// SPI for MAX Thermocouple
// Uses a separate SPI bus
-// If you have a two-way thermocouple, you can customize two THERMO_CSx_PIN pins (x:1~2)
+// If you have a two-way thermocouple, you can customize two TEMP_x_CS_PIN pins (x:0~1)
-#define THERMO_SCK_PIN PI1 // SCK
-#define THERMO_DO_PIN PI2 // MISO
-#define THERMO_CS1_PIN PH9 // GTR K-TEMP
-#define THERMO_CS2_PIN PH2 // M5 K-TEMP
+#define TEMP_0_CS_PIN PH9 // GTR K-TEMP
+#define TEMP_0_SCK_PIN PI1 // SCK
+#define TEMP_0_MISO_PIN PI2 // MISO
+//#define TEMP_0_MOSI_PIN ... // For MAX31865
-#define MAX6675_SS_PIN THERMO_CS1_PIN
-#define MAX6675_SS2_PIN THERMO_CS2_PIN
-#define MAX6675_SCK_PIN THERMO_SCK_PIN
-#define MAX6675_DO_PIN THERMO_DO_PIN
+#define TEMP_1_CS_PIN PH2 // M5 K-TEMP
+#define TEMP_1_SCK_PIN TEMP_0_SCK_PIN
+#define TEMP_1_MISO_PIN TEMP_0_MISO_PIN
+//#define TEMP_1_MOSI_PIN TEMP_0_MOSI_PIN
//
// Heaters / Fans
diff --git a/Marlin/src/pins/stm32f4/pins_LERDGE_S.h b/Marlin/src/pins/stm32f4/pins_LERDGE_S.h
index 105d0d6f6070..65db99025c8b 100644
--- a/Marlin/src/pins/stm32f4/pins_LERDGE_S.h
+++ b/Marlin/src/pins/stm32f4/pins_LERDGE_S.h
@@ -104,16 +104,16 @@
// MAX6675 Cold-Junction-Compensated K-Thermocouple to Digital Converter (0°C to +1024°C)
// https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf
-#define MAX6675_SCK_PIN PB3 // max6675 datasheet: SCK pin, found with multimeter, not tested
-#define MAX6675_DO_PIN PB4 // max6675 datasheet: SO pin, found with multimeter, not tested
-#define MAX6675_SS_PIN PC4 // max6675 datasheet: /CS pin, found with multimeter, not tested and likely wrong
+#define TEMP_0_CS_PIN PC4 // max6675 datasheet: /CS pin, found with multimeter, not tested and likely wrong
+#define TEMP_0_SCK_PIN PB3 // max6675 datasheet: SCK pin, found with multimeter, not tested
+#define TEMP_0_MISO_PIN PB4 // max6675 datasheet: SO pin, found with multimeter, not tested
// Expansion board with second max6675
// Warning: Some boards leave the slot unpopulated.
-//#define MAX6675_SCK2_PIN PB3 // max6675 datasheet: SCK pin, found with multimeter, not tested
-//#define MAX6675_DO2_PIN PB4 // max6675 datasheet: SO pin, found with multimeter, not tested
-//#define MAX6675_SS2_PIN PF1 // max6675 datasheet: /CS pin, found with multimeter, not tested
+//#define TEMP_1_CS_PIN PF1 // max6675 datasheet: /CS pin, found with multimeter, not tested
+//#define TEMP_1_SCK_PIN PB3 // max6675 datasheet: SCK pin, found with multimeter, not tested
+//#define TEMP_1_MISO_PIN PB4 // max6675 datasheet: SO pin, found with multimeter, not tested
//
// Heaters / Fans
diff --git a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h
index 5a056b97cdfa..9ae2870a4053 100644
--- a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h
+++ b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h
@@ -172,8 +172,8 @@
//
// Thermocouples
//
-//#define MAX6675_SS_PIN HEATER_0_PIN // TC1 - CS1
-//#define MAX6675_SS_PIN HEATER_1_PIN // TC2 - CS2
+//#define TEMP_0_CS_PIN HEATER_0_PIN // TC1 - CS1
+//#define TEMP_0_CS_PIN HEATER_1_PIN // TC2 - CS2
//
// Misc. Functions
diff --git a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h
index 2b0df002d394..0b9512a1cbe5 100644
--- a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h
+++ b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h
@@ -189,8 +189,8 @@
//
// Thermocouples
//
-//#define MAX6675_SS_PIN PE5 // TC1 - CS1
-//#define MAX6675_SS_PIN PE6 // TC2 - CS2
+//#define TEMP_0_CS_PIN PE5 // TC1 - CS1
+//#define TEMP_0_CS_PIN PE6 // TC2 - CS2
//
// Misc. Functions
diff --git a/ini/features.ini b/ini/features.ini
index a1e96884474f..5a1b48804dd5 100644
--- a/ini/features.ini
+++ b/ini/features.ini
@@ -27,9 +27,9 @@ HAS_TMC26X = TMC26XStepper=https://github.com/trinam
src_filter=+
HAS_L64XX = Arduino-L6470@0.8.0
src_filter=+ + + +
+LIB_INTERNAL_MAX31865 = src_filter=+
NEOPIXEL_LED = adafruit/Adafruit NeoPixel@~1.8.0
src_filter=+
-TEMP_.+_IS_MAX31865 = Adafruit MAX31865 library@~1.1.0
I2C_AMMETER = peterus/INA226Lib@1.1.2
USES_LIQUIDCRYSTAL = fmalpartida/LiquidCrystal@1.5.0
USES_LIQUIDCRYSTAL_I2C = marcoschwartz/LiquidCrystal_I2C@1.1.4
diff --git a/platformio.ini b/platformio.ini
index 30f70668a34a..4bbd3667c136 100644
--- a/platformio.ini
+++ b/platformio.ini
@@ -230,6 +230,7 @@ default_src_filter = + - - +
-
- -
- - -
+ -
-
-
- -