Add files for alt34 keyboard design

keyboards/alt34/alt34.c

@@ -0,0 +1,18 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "alt34.h"

keyboards/alt34/alt34.h

@@ -0,0 +1,24 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "quantum.h"
+
+#ifdef KEYBOARD_alt34_rev1
+    #include "rev1.h"
+#endif

keyboards/alt34/config.h

@@ -0,0 +1,20 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"

keyboards/alt34/info.json

@@ -0,0 +1,52 @@
+{
+    "keyboard_name": "alt34",
+    "url": "https://gitlab.com/altosys/alt34",
+    "maintainer": "@altosys",
+    "layouts": {
+        "LAYOUT_split_3x5_2": {
+            "layout": [
+                {"x": 0, "y": 0.93},
+                {"x": 1, "y": 0.31},
+                {"x": 2, "y": 0},
+                {"x": 3, "y": 0.28},
+                {"x": 4, "y": 0.42},
+
+                {"x": 7, "y": 0.42},
+                {"x": 8, "y": 0.28},
+                {"x": 9, "y": 0},
+                {"x": 10, "y": 0.31},
+                {"x": 11, "y": 0.93},
+
+                {"x": 0, "y": 1.93},
+                {"x": 1, "y": 1.31},
+                {"x": 2, "y": 1},
+                {"x": 3, "y": 1.28},
+                {"x": 4, "y": 1.42},
+
+                {"x": 7, "y": 1.42},
+                {"x": 8, "y": 1.28},
+                {"x": 9, "y": 1},
+                {"x": 10, "y": 1.31},
+                {"x": 11, "y": 1.93},
+
+                {"x": 0, "y": 2.93},
+                {"x": 1, "y": 2.31},
+                {"x": 2, "y": 2},
+                {"x": 3, "y": 2.28},
+                {"x": 4, "y": 2.42},
+
+                {"x": 7, "y": 2.42},
+                {"x": 8, "y": 2.28},
+                {"x": 9, "y": 2},
+                {"x": 10, "y": 2.31},
+                {"x": 11, "y": 2.93},
+
+                {"x": 3.5, "y": 3.45},
+                {"x": 4.5, "y": 3.7},
+
+                {"x": 6.5, "y": 3.7},
+                {"x": 7.5, "y": 3.45}
+            ]
+        }
+    }
+}

keyboards/alt34/keymaps/default/config.h

@@ -0,0 +1,27 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+/* Use I2C or Serial, not both */
+#define USE_I2C
+/* #define USE_SERIAL */
+
+/* Select hand configuration */
+#define EE_HANDS
+/* #define MASTER_LEFT */
+/* #define MASTER_RIGHT */

keyboards/alt34/keymaps/default/keymap.c

@@ -0,0 +1,32 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include QMK_KEYBOARD_H
+
+// Define aliases for layers
+enum layers {
+    BASE,
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[BASE] = LAYOUT_split_3x5_2(
+   KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,
+   KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN,
+   KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,
+                              KC_SPC,  KC_TAB,  KC_BSPC, KC_ENT
+   )
+};

keyboards/alt34/readme.md

@@ -0,0 +1,66 @@
+# alt34
+
+![alt34](https://i.imgur.com/GDv0dL0h.png)
+
+alt34 was designed as a minimalistic, 'no frills' workhorse keyboard with focus on efficiency and ergonomics.
+This breaks down into the following priorities in the design:
+
+* Keyboard Maintainer: [Tommy Alatalo](https://github.com/altosys)
+* Hardware Supported: 
+   * Compact 34 key split layout with two thumb keys per hand
+   * Orthogonal layout with a somewhat aggressive column stagger
+   * Compatibility with standard controllers (Elite-C, Pro Micro etc.)
+   * Cherry MX switch support
+   * Kailh hotswap socket support
+   * Tenting puck support
+
+## Hardware
+
+A bill of materials for building alt34 is found in [the alt34 git repo](https://gitlab.com/altosys/alt34)
+
+## Bootloader
+
+Enter the bootloader in 3 ways:
+
+* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
+* **Physical reset jumper**: Briefly short the pads just below the TRRS connector on the PCB
+* **Keycode in layout**: Press the key mapped to `RESET` if it is available
+
+Latest updates and information for alt34 is found at https://gitlab.com/altosys/alt34
+
+## Build Guide
+
+There is no dedicated build guide for alt34. If you are a novice builder and need guidance then suggested reading would be build guides for the Corne keyboard (aka. crkbd), they will cover the usual installation of the controller, diodes and hotswap sockets, which is essentially all there is to assembling the alt34.
+
+## Flashing QMK Firmware
+
+Set up your build environment according to the QMK documentation, then after cloning the `qmk_firmware` repository you can run the below commands in the repo root to build and flash the firmware onto your controller.
+
+Note that this method enables `EE_HANDS` mode which allows you to connect the USB cable to either half of alt34 when using the keyboard.
+
+
+Flash `EE_HANDS` to the left hand half, this updates the persistent EEPROM storage along with the firmware.
+Run the below command and then set the board into bootloader mode by bridging the reset pads below the TRRS connector with a paper clip or similar.
+```
+make alt34/rev1:default:dfu-split-left
+```
+
+Do the same for the right hand side:
+```
+make alt34/rev1:default:dfu-split-right
+```
+
+Now you should be able to connect the USB cable to either side of the split and it should work the same.
+
+For any further changes it is enough to flash only the firmware and not the EEPROM:
+```
+make alt34/rev1:default:flash
+```
+
+It is still recommended to do this for both sides of the split when updating keymaps etc.
+
+**Note I:** the above examples are using an Elite-C controller with an `atmel-dfu` bootloader, adjust this according to your own hardware.
+
+**Note II:** the included keymap is rudimentary, the recommended layout to use with alt34 is `miryoku`, see the [miryoku docs](https://github.com/manna-harbour/miryoku) for instructions.
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/alt34/rev1/config.h

@@ -0,0 +1,46 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x1ABC
+#define PRODUCT_ID      0x0001
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    altosys
+#define PRODUCT         alt34
+
+/* key matrix size */
+// Rows are doubled-up
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 5
+
+// wiring of each half
+#define MATRIX_ROW_PINS { D7, E6, B4, B5 }
+#define MATRIX_COL_PINS { B6, B2, B3, B1, F7 }
+#define DIODE_DIRECTION COL2ROW
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCE 5
+
+/* serial.c configuration for split keyboard */
+/* #define SOFT_SERIAL_PIN D0 */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE

keyboards/alt34/rev1/rev1.c

@@ -0,0 +1,18 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "alt34.h"

keyboards/alt34/rev1/rev1.h

@@ -0,0 +1,42 @@
+/*
+Copyright 2022 Tommy Alatalo <@altosys>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "alt34.h"
+#include "quantum.h"
+
+#define ____ KC_NO
+
+/*              left hand                     right hand            */
+#define LAYOUT_split_3x5_2(\
+    K0_0, K0_1, K0_2, K0_3, K0_4,       K0_5, K0_6, K0_7, K0_8, K0_9,\
+    K1_0, K1_1, K1_2, K1_3, K1_4,       K1_5, K1_6, K1_7, K1_8, K1_9,\
+    K2_0, K2_1, K2_2, K2_3, K2_4,       K2_5, K2_6, K2_7, K2_8, K2_9,\
+                      K3_2, K3_3,       K3_4, K3_5 )\
+/* matrix positions */\
+{\
+    {K0_0,  K0_1,  K0_2,  K0_3,  K0_4},\
+    {K1_0,  K1_1,  K1_2,  K1_3,  K1_4},\
+    {K2_0,  K2_1,  K2_2,  K2_3,  K2_4},\
+    {____,  ____,  ____,  K3_2,  K3_3},\
+	\
+	{K0_9,  K0_8,  K0_7,  K0_6,  K0_5},\
+	{K1_9,  K1_8,  K1_7,  K1_6,  K1_5},\
+	{K2_9,  K2_8,  K2_7,  K2_6,  K2_5},\
+	{____,  ____,  ____,  K3_5,  K3_4} \
+}

keyboards/alt34/rev1/rules.mk

@@ -0,0 +1,22 @@
+# MCU name
+MCU = atmega32u4
+
+# Bootloader selection
+BOOTLOADER = atmel-dfu
+
+# Build Options
+#   change to "no" to disable the options
+#
+BOOTMAGIC_ENABLE = no       # Enable Bootmagic Lite
+MOUSEKEY_ENABLE = no        # Mouse keys
+EXTRAKEY_ENABLE = no        # Audio control and System control
+CONSOLE_ENABLE = no         # Console for debug
+COMMAND_ENABLE = no         # Commands for debug and configuration
+NKRO_ENABLE = no            # Enable N-Key Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+AUDIO_ENABLE = no           # Audio output
+
+SPLIT_KEYBOARD = yes
+LAYOUTS = split_3x5_2
+DEFAULT_FOLDER = alt34/rev1