With Debian >11, config.txt and cmdline.txt is in /boot/firmware

install/Sixfab_PPP_Installer-master/ppp_installer/install.sh

@@ -0,0 +1,146 @@
+#!/bin/bash
+
+# This file is a part of TorBox, an easy to use anonymizing router based on Raspberry Pi.
+# Copyright (C) 2024 Patrick Truffer
+# Contact: anonym@torbox.ch
+# Website: https://www.torbox.ch
+# Github: https://github.com/radio24/TorBox
+#
+# This file was initially created on November 27, 2020 by Yasin Kaya (selengalp)
+# Location of last known original file: https://github.com/sixfab/Sixfab_PPP_Installer
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 3 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it is useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+#
+# DESCRIPTION
+# This file installs the support software for Sixfab Shields/HATs.
+#
+# SYNTAX
+# ./install.sh
+#
+###### SET VARIABLES ######
+#
+# Colors
+YELLOW='\033[1;33m'
+RED='\033[1;31m'
+BLUE='\033[1;34m'
+YELLOW='\033[1;93m'
+SET='\033[0m'
+
+# Global Varibales
+POWERUP_REQ=1
+POWERUP_NOT_REQ=0
+STATUS_GPRS=19
+STATUS_CELL_IOT_APP=20
+STATUS_CELL_IOT=23
+STATUS_TRACKER=23
+POWERKEY_GPRS=26
+POWERKEY_CELL_IOT_APP=11
+POWERKEY_CELL_IOT=24
+POWERKEY_TRACKER=24
+
+# Where is the config.txt?
+if [ "$DEBIAN_VERSION" -gt "11" ]; then
+ CONFIGFILE="/boot/firmware/config.txt"
+else
+ CONFIGFILE="/boot/config.txt"
+fi
+
+clear
+echo -e "${RED}[+] Installing Sixfab Shield/HATs support${NOCOLOR}"
+echo -e ""
+
+# Menu
+clear
+echo -e "${YELLOW}Please choose your Sixfab Shield/HAT:${SET}"
+echo -e "${RED}1: GSM/GPRS Shield${SET}"
+echo -e "${RED}2: 3G, 4G/LTE Base Shield${SET}"
+echo -e "${RED}3: Cellular IoT App Shield${SET}"
+echo -e "${RED}4: Cellular IoT HAT${SET}"
+echo -e "${RED}5: Tracker HAT${SET}"
+echo -e "${RED}6: 3G/4G Base HAT${SET}"
+echo -e ""
+
+read shield_hat
+clear
+case $shield_hat in
+ 1) echo -e "${RED}[+] You chose GSM/GPRS Shield${SET}";;
+ 2) echo -e "${RED}[+] You chose Base Shield${SET}";;
+ 3) echo -e "${RED}[+] You chose CellularIoT Shield${SET}";;
+ 4) echo -e "${RED}[+] You chose CellularIoT HAT${SET}";;
+ 5) echo -e "${RED}[+] You chose Tracker HAT${SET}";;
+ 6) echo -e "${RED}[+] You chose 3G/4G Base HAT${SET}";;
+ *) echo -e "${YELLOW}[!] Wrong Selection, exiting${SET}"; exit 1;
+esac
+sleep 3
+
+#Downloading setup files as will as ppp wiringpi is not necessary, because they are already there
+#However, we have to copy some unchanged configuration files
+sudo cp unchanged_files/provider .
+sudo cp unchanged_files/configure_modem.sh .
+
+clear
+echo -e "${RED}Enter your carrier APN:${SET}"
+echo -e "${RED}(for more information see here: https://www.torbox.ch/?page_id=1030)${SET}"
+read carrierapn
+
+while [ 1 ]
+do
+ echo ""
+ echo -e "${RED}Does your carrier need username and password? [Y/n]${SET}"
+ read usernpass
+
+ case $usernpass in
+ [Yy]* ) while [ 1 ]
+ do
+
+ echo -e "${RED}Enter username${SET}"
+ read username
+
+ echo -e "${RED}Enter password${SET}"
+ read password
+ sed -i "s/noauth/#noauth\nuser \"$username\"\npassword \"$password\"/" provider
+ break
+ done
+
+ break;;
+
+ [Nn]* ) break;;
+ *) echo -e "${YELLOW}Wrong Selection, Select among Y or n${SET}";;
+ esac
+done
+
+mkdir -p /etc/chatscripts
+cp chat-connect /etc/chatscripts/
+cp chat-disconnect /etc/chatscripts/
+
+mkdir -p /etc/ppp/peers
+sed -i "s/#APN/$carrierapn/" provider
+mv provider /etc/ppp/peers/provider
+
+if ! (grep -q 'sudo route' /etc/ppp/ip-up ); then
+ echo "sudo route add default ppp0" >> /etc/ppp/ip-up
+fi
+
+if [ $shield_hat -eq 2 ]; then
+ if ! (grep -q 'max_usb_current' ${CONFIGFILE} ); then
+ echo "max_usb_current=1" >> ${CONFIGFILE}
+ fi
+fi
+
+sleep 2
+clear
+echo -e "${YELLOW}The installation of the Sixfab Shield/HATs support is done!${SET}"
+echo -e "${RED}To connect to internet use main menu entry 8${SET}"
+echo -e ""
+read -n 1 -s -r -p "Press any key to continue"

menu-config

@@ -1115,8 +1115,9 @@ case "$CHOICE" in
  INPUT=$(cat text/sixfab-text)
  if (whiptail --defaultno --yesno "$INPUT" $MENU_HEIGHT_25 $MENU_WIDTH); then
  #Original file: https://raw.githubusercontent.com/sixfab/Sixfab_PPP_Installer/master/ppp_installer/install.sh
- chmod +x install/Sixfab_PPP_Installer-master/install.sh
- sudo ./install/Sixfab_PPP_Installer-master/install.sh
+ cd install/Sixfab_PPP_Installer-master/ppp_installer
+ chmod +x install.sh
+ sudo ./install.sh
  fi
  ;;