diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index fe904846e358..bdf86392c97f 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -221,7 +221,7 @@ #define BOARD_5DPRINT 1707 // 5DPrint D8 Driver Board // -// LPC1768 ARM Cortex M3 +// LPC1768 ARM Cortex-M3 // #define BOARD_RAMPS_14_RE_ARM_EFB 2000 // Re-ARM with RAMPS 1.4 (Power outputs: Hotend, Fan, Bed) @@ -242,7 +242,7 @@ #define BOARD_EMOTRONIC 2015 // eMotion-Tech eMotronic // -// LPC1769 ARM Cortex M3 +// LPC1769 ARM Cortex-M3 // #define BOARD_MKS_SGEN 2500 // MKS-SGen @@ -259,7 +259,7 @@ #define BOARD_FLY_CDY 2511 // FLYmaker FLY CDY // -// SAM3X8E ARM Cortex M3 +// SAM3X8E ARM Cortex-M3 // #define BOARD_DUE3DOM 3000 // DUE3DOM for Arduino DUE @@ -292,185 +292,195 @@ #define BOARD_KRATOS32 3027 // K.3D Kratos32 (Arduino Due Shield) // -// SAM3X8C ARM Cortex M3 +// SAM3X8C ARM Cortex-M3 // #define BOARD_PRINTRBOARD_G2 3100 // Printrboard G2 #define BOARD_ADSK 3101 // Arduino DUE Shield Kit (ADSK) +// +// STM32 ARM Cortex-M0+ +// + +#define BOARD_BTT_EBB42_V1_1 4000 // BigTreeTech EBB42 V1.1 (STM32G0B1CB) +#define BOARD_BTT_SKR_MINI_E3_V3_0 4001 // BigTreeTech SKR Mini E3 V3.0 (STM32G0B1RE) +#define BOARD_BTT_MANTA_E3_EZ_V1_0 4002 // BigTreeTech Manta E3 EZ V1.0 (STM32G0B1RE) +#define BOARD_BTT_MANTA_M4P_V1_0 4003 // BigTreeTech Manta M4P V1.0 (STM32G0B1RE) +#define BOARD_BTT_MANTA_M5P_V1_0 4004 // BigTreeTech Manta M5P V1.0 (STM32G0B1RE) +#define BOARD_BTT_MANTA_M8P_V1_0 4005 // BigTreeTech Manta M8P V1.0 (STM32G0B1VE) +#define BOARD_BTT_MANTA_M8P_V1_1 4006 // BigTreeTech Manta M8P V1.1 (STM32G0B1VE) + // // STM32 ARM Cortex-M3 // -#define BOARD_MALYAN_M200_V2 4000 // STM32F070CB controller -#define BOARD_MALYAN_M300 4001 // STM32F070-based delta -#define BOARD_STM32F103RE 4002 // STM32F103RE Libmaple-based STM32F1 controller -#define BOARD_MALYAN_M200 4003 // STM32C8 Libmaple-based STM32F1 controller -#define BOARD_STM3R_MINI 4004 // STM32F103RE Libmaple-based STM32F1 controller -#define BOARD_GTM32_PRO_VB 4005 // STM32F103VE controller -#define BOARD_GTM32_MINI 4006 // STM32F103VE controller -#define BOARD_GTM32_MINI_A30 4007 // STM32F103VE controller -#define BOARD_GTM32_REV_B 4008 // STM32F103VE controller -#define BOARD_MORPHEUS 4009 // STM32F103C8 / STM32F103CB Libmaple-based STM32F1 controller -#define BOARD_CHITU3D 4010 // Chitu3D (STM32F103RE) -#define BOARD_MKS_ROBIN 4011 // MKS Robin (STM32F103ZE) -#define BOARD_MKS_ROBIN_MINI 4012 // MKS Robin Mini (STM32F103VE) -#define BOARD_MKS_ROBIN_NANO 4013 // MKS Robin Nano (STM32F103VE) -#define BOARD_MKS_ROBIN_NANO_V2 4014 // MKS Robin Nano V2 (STM32F103VE) -#define BOARD_MKS_ROBIN_LITE 4015 // MKS Robin Lite/Lite2 (STM32F103RC) -#define BOARD_MKS_ROBIN_LITE3 4016 // MKS Robin Lite3 (STM32F103RC) -#define BOARD_MKS_ROBIN_PRO 4017 // MKS Robin Pro (STM32F103ZE) -#define BOARD_MKS_ROBIN_E3 4018 // MKS Robin E3 (STM32F103RC) -#define BOARD_MKS_ROBIN_E3_V1_1 4019 // MKS Robin E3 V1.1 (STM32F103RC) -#define BOARD_MKS_ROBIN_E3D 4020 // MKS Robin E3D (STM32F103RC) -#define BOARD_MKS_ROBIN_E3D_V1_1 4021 // MKS Robin E3D V1.1 (STM32F103RC) -#define BOARD_MKS_ROBIN_E3P 4022 // MKS Robin E3p (STM32F103VE) -#define BOARD_BTT_EBB42_V1_1 4023 // BigTreeTech EBB42 V1.1 (STM32G0B1CB) -#define BOARD_BTT_SKR_MINI_V1_1 4024 // BigTreeTech SKR Mini v1.1 (STM32F103RC) -#define BOARD_BTT_SKR_MINI_E3_V1_0 4025 // BigTreeTech SKR Mini E3 (STM32F103RC) -#define BOARD_BTT_SKR_MINI_E3_V1_2 4026 // BigTreeTech SKR Mini E3 V1.2 (STM32F103RC) -#define BOARD_BTT_SKR_MINI_E3_V2_0 4027 // BigTreeTech SKR Mini E3 V2.0 (STM32F103RC / STM32F103RE) -#define BOARD_BTT_SKR_MINI_E3_V3_0 4028 // BigTreeTech SKR Mini E3 V3.0 (STM32G0B1RE) -#define BOARD_BTT_SKR_MINI_E3_V3_0_1 4029 // BigTreeTech SKR Mini E3 V3.0.1 (STM32F401RC) -#define BOARD_BTT_SKR_MINI_MZ_V1_0 4030 // BigTreeTech SKR Mini MZ V1.0 (STM32F103RC) -#define BOARD_BTT_SKR_E3_DIP 4031 // BigTreeTech SKR E3 DIP V1.0 (STM32F103RC / STM32F103RE) -#define BOARD_BTT_SKR_CR6 4032 // BigTreeTech SKR CR6 v1.0 (STM32F103RE) -#define BOARD_JGAURORA_A5S_A1 4033 // JGAurora A5S A1 (STM32F103ZE) -#define BOARD_FYSETC_AIO_II 4034 // FYSETC AIO_II (STM32F103RC) -#define BOARD_FYSETC_CHEETAH 4035 // FYSETC Cheetah (STM32F103RC) -#define BOARD_FYSETC_CHEETAH_V12 4036 // FYSETC Cheetah V1.2 (STM32F103RC) -#define BOARD_LONGER3D_LK 4037 // Longer3D LK1/2 - Alfawise U20/U20+/U30 (STM32F103VE) -#define BOARD_CCROBOT_MEEB_3DP 4038 // ccrobot-online.com MEEB_3DP (STM32F103RC) -#define BOARD_CHITU3D_V5 4039 // Chitu3D TronXY X5SA V5 Board (STM32F103ZE) -#define BOARD_CHITU3D_V6 4040 // Chitu3D TronXY X5SA V6 Board (STM32F103ZE) -#define BOARD_CHITU3D_V9 4041 // Chitu3D TronXY X5SA V9 Board (STM32F103ZE) -#define BOARD_CREALITY_V4 4042 // Creality v4.x (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V422 4043 // Creality v4.2.2 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V423 4044 // Creality v4.2.3 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V425 4045 // Creality v4.2.5 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V427 4046 // Creality v4.2.7 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V4210 4047 // Creality v4.2.10 (STM32F103RC / STM32F103RE) as found in the CR-30 -#define BOARD_CREALITY_V431 4048 // Creality v4.3.1 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V431_A 4049 // Creality v4.3.1a (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V431_B 4050 // Creality v4.3.1b (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V431_C 4051 // Creality v4.3.1c (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V431_D 4052 // Creality v4.3.1d (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V452 4053 // Creality v4.5.2 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V453 4054 // Creality v4.5.3 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V521 4055 // Creality v5.2.1 (STM32F103VE) as found in the SV04 -#define BOARD_CREALITY_V24S1 4056 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7 -#define BOARD_CREALITY_V24S1_301 4057 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1 -#define BOARD_CREALITY_V25S1 4058 // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro -#define BOARD_TRIGORILLA_PRO 4059 // Trigorilla Pro (STM32F103ZE) -#define BOARD_FLY_MINI 4060 // FLYmaker FLY MINI (STM32F103RC) -#define BOARD_FLSUN_HISPEED 4061 // FLSUN HiSpeedV1 (STM32F103VE) -#define BOARD_BEAST 4062 // STM32F103RE Libmaple-based controller -#define BOARD_MINGDA_MPX_ARM_MINI 4063 // STM32F103ZE Mingda MD-16 -#define BOARD_GTM32_PRO_VD 4064 // STM32F103VE controller -#define BOARD_ZONESTAR_ZM3E2 4065 // Zonestar ZM3E2 (STM32F103RC) -#define BOARD_ZONESTAR_ZM3E4 4066 // Zonestar ZM3E4 V1 (STM32F103VC) -#define BOARD_ZONESTAR_ZM3E4V2 4067 // Zonestar ZM3E4 V2 (STM32F103VC) -#define BOARD_ERYONE_ERY32_MINI 4068 // Eryone Ery32 mini (STM32F103VE) -#define BOARD_PANDA_PI_V29 4069 // Panda Pi V2.9 - Standalone (STM32F103RC) +#define BOARD_MALYAN_M200_V2 5000 // STM32F070CB controller +#define BOARD_MALYAN_M300 5001 // STM32F070-based delta +#define BOARD_STM32F103RE 5002 // STM32F103RE Libmaple-based STM32F1 controller +#define BOARD_MALYAN_M200 5003 // STM32C8 Libmaple-based STM32F1 controller +#define BOARD_STM3R_MINI 5004 // STM32F103RE Libmaple-based STM32F1 controller +#define BOARD_GTM32_PRO_VB 5005 // STM32F103VE controller +#define BOARD_GTM32_MINI 5006 // STM32F103VE controller +#define BOARD_GTM32_MINI_A30 5007 // STM32F103VE controller +#define BOARD_GTM32_REV_B 5008 // STM32F103VE controller +#define BOARD_MORPHEUS 5009 // STM32F103C8 / STM32F103CB Libmaple-based STM32F1 controller +#define BOARD_CHITU3D 5010 // Chitu3D (STM32F103RE) +#define BOARD_MKS_ROBIN 5011 // MKS Robin (STM32F103ZE) +#define BOARD_MKS_ROBIN_MINI 5012 // MKS Robin Mini (STM32F103VE) +#define BOARD_MKS_ROBIN_NANO 5013 // MKS Robin Nano (STM32F103VE) +#define BOARD_MKS_ROBIN_NANO_V2 5014 // MKS Robin Nano V2 (STM32F103VE) +#define BOARD_MKS_ROBIN_LITE 5015 // MKS Robin Lite/Lite2 (STM32F103RC) +#define BOARD_MKS_ROBIN_LITE3 5016 // MKS Robin Lite3 (STM32F103RC) +#define BOARD_MKS_ROBIN_PRO 5017 // MKS Robin Pro (STM32F103ZE) +#define BOARD_MKS_ROBIN_E3 5018 // MKS Robin E3 (STM32F103RC) +#define BOARD_MKS_ROBIN_E3_V1_1 5019 // MKS Robin E3 V1.1 (STM32F103RC) +#define BOARD_MKS_ROBIN_E3D 5020 // MKS Robin E3D (STM32F103RC) +#define BOARD_MKS_ROBIN_E3D_V1_1 5021 // MKS Robin E3D V1.1 (STM32F103RC) +#define BOARD_MKS_ROBIN_E3P 5022 // MKS Robin E3P (STM32F103VE) +#define BOARD_BTT_SKR_MINI_V1_1 5023 // BigTreeTech SKR Mini v1.1 (STM32F103RC) +#define BOARD_BTT_SKR_MINI_E3_V1_0 5024 // BigTreeTech SKR Mini E3 (STM32F103RC) +#define BOARD_BTT_SKR_MINI_E3_V1_2 5025 // BigTreeTech SKR Mini E3 V1.2 (STM32F103RC) +#define BOARD_BTT_SKR_MINI_E3_V2_0 5026 // BigTreeTech SKR Mini E3 V2.0 (STM32F103RC / STM32F103RE) +#define BOARD_BTT_SKR_MINI_MZ_V1_0 5027 // BigTreeTech SKR Mini MZ V1.0 (STM32F103RC) +#define BOARD_BTT_SKR_E3_DIP 5028 // BigTreeTech SKR E3 DIP V1.0 (STM32F103RC / STM32F103RE) +#define BOARD_BTT_SKR_CR6 5029 // BigTreeTech SKR CR6 v1.0 (STM32F103RE) +#define BOARD_JGAURORA_A5S_A1 5030 // JGAurora A5S A1 (STM32F103ZE) +#define BOARD_FYSETC_AIO_II 5031 // FYSETC AIO_II (STM32F103RC) +#define BOARD_FYSETC_CHEETAH 5032 // FYSETC Cheetah (STM32F103RC) +#define BOARD_FYSETC_CHEETAH_V12 5033 // FYSETC Cheetah V1.2 (STM32F103RC) +#define BOARD_LONGER3D_LK 5034 // Longer3D LK1/2 - Alfawise U20/U20+/U30 (STM32F103VE) +#define BOARD_CCROBOT_MEEB_3DP 5035 // ccrobot-online.com MEEB_3DP (STM32F103RC) +#define BOARD_CHITU3D_V5 5036 // Chitu3D TronXY X5SA V5 Board (STM32F103ZE) +#define BOARD_CHITU3D_V6 5037 // Chitu3D TronXY X5SA V6 Board (STM32F103ZE) +#define BOARD_CHITU3D_V9 5038 // Chitu3D TronXY X5SA V9 Board (STM32F103ZE) +#define BOARD_CREALITY_V4 5039 // Creality v4.x (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V422 5040 // Creality v4.2.2 (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V423 5041 // Creality v4.2.3 (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V425 5042 // Creality v4.2.5 (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V427 5043 // Creality v4.2.7 (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V4210 5044 // Creality v4.2.10 (STM32F103RC / STM32F103RE) as found in the CR-30 +#define BOARD_CREALITY_V431 5045 // Creality v4.3.1 (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V431_A 5046 // Creality v4.3.1a (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V431_B 5047 // Creality v4.3.1b (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V431_C 5048 // Creality v4.3.1c (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V431_D 5049 // Creality v4.3.1d (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V452 5050 // Creality v4.5.2 (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V453 5051 // Creality v4.5.3 (STM32F103RC / STM32F103RE) +#define BOARD_CREALITY_V521 5052 // Creality v5.2.1 (STM32F103VE) as found in the SV04 +#define BOARD_CREALITY_V24S1 5053 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7 +#define BOARD_CREALITY_V24S1_301 5054 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1 +#define BOARD_CREALITY_V25S1 5055 // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro +#define BOARD_TRIGORILLA_PRO 5056 // Trigorilla Pro (STM32F103ZE) +#define BOARD_FLY_MINI 5057 // FLYmaker FLY MINI (STM32F103RC) +#define BOARD_FLSUN_HISPEED 5058 // FLSUN HiSpeedV1 (STM32F103VE) +#define BOARD_BEAST 5059 // STM32F103RE Libmaple-based controller +#define BOARD_MINGDA_MPX_ARM_MINI 5060 // STM32F103ZE Mingda MD-16 +#define BOARD_GTM32_PRO_VD 5061 // STM32F103VE controller +#define BOARD_ZONESTAR_ZM3E2 5062 // Zonestar ZM3E2 (STM32F103RC) +#define BOARD_ZONESTAR_ZM3E4 5063 // Zonestar ZM3E4 V1 (STM32F103VC) +#define BOARD_ZONESTAR_ZM3E4V2 5064 // Zonestar ZM3E4 V2 (STM32F103VC) +#define BOARD_ERYONE_ERY32_MINI 5065 // Eryone Ery32 mini (STM32F103VE) +#define BOARD_PANDA_PI_V29 5066 // Panda Pi V2.9 - Standalone (STM32F103RC) // // ARM Cortex-M4F // -#define BOARD_TEENSY31_32 4100 // Teensy3.1 and Teensy3.2 -#define BOARD_TEENSY35_36 4101 // Teensy3.5 and Teensy3.6 +#define BOARD_TEENSY31_32 5100 // Teensy3.1 and Teensy3.2 +#define BOARD_TEENSY35_36 5101 // Teensy3.5 and Teensy3.6 // // STM32 ARM Cortex-M4F // -#define BOARD_ARMED 4200 // Arm'ed STM32F4-based controller -#define BOARD_RUMBA32_V1_0 4201 // RUMBA32 STM32F446VE based controller from Aus3D -#define BOARD_RUMBA32_V1_1 4202 // RUMBA32 STM32F446VE based controller from Aus3D -#define BOARD_RUMBA32_MKS 4203 // RUMBA32 STM32F446VE based controller from Makerbase -#define BOARD_RUMBA32_BTT 4204 // RUMBA32 STM32F446VE based controller from BIGTREETECH -#define BOARD_BLACK_STM32F407VE 4205 // BLACK_STM32F407VE -#define BOARD_BLACK_STM32F407ZE 4206 // BLACK_STM32F407ZE -#define BOARD_BTT_SKR_PRO_V1_1 4207 // BigTreeTech SKR Pro v1.1 (STM32F407ZG) -#define BOARD_BTT_SKR_PRO_V1_2 4208 // BigTreeTech SKR Pro v1.2 (STM32F407ZG) -#define BOARD_BTT_BTT002_V1_0 4209 // BigTreeTech BTT002 v1.0 (STM32F407VG) -#define BOARD_BTT_E3_RRF 4210 // BigTreeTech E3 RRF (STM32F407VG) -#define BOARD_BTT_SKR_V2_0_REV_A 4211 // BigTreeTech SKR v2.0 Rev A (STM32F407VG) -#define BOARD_BTT_SKR_V2_0_REV_B 4212 // BigTreeTech SKR v2.0 Rev B (STM32F407VG/STM32F429VG) -#define BOARD_BTT_GTR_V1_0 4213 // BigTreeTech GTR v1.0 (STM32F407IGT) -#define BOARD_BTT_OCTOPUS_V1_0 4214 // BigTreeTech Octopus v1.0 (STM32F446ZE) -#define BOARD_BTT_OCTOPUS_V1_1 4215 // BigTreeTech Octopus v1.1 (STM32F446ZE) -#define BOARD_BTT_OCTOPUS_PRO_V1_0 4216 // BigTreeTech Octopus Pro v1.0 (STM32F446ZE / STM32F429ZG) -#define BOARD_LERDGE_K 4217 // Lerdge K (STM32F407ZG) -#define BOARD_LERDGE_S 4218 // Lerdge S (STM32F407VE) -#define BOARD_LERDGE_X 4219 // Lerdge X (STM32F407VE) -#define BOARD_VAKE403D 4220 // VAkE 403D (STM32F446VE) -#define BOARD_FYSETC_S6 4221 // FYSETC S6 (STM32F446VE) -#define BOARD_FYSETC_S6_V2_0 4222 // FYSETC S6 v2.0 (STM32F446VE) -#define BOARD_FYSETC_SPIDER 4223 // FYSETC Spider (STM32F446VE) -#define BOARD_FLYF407ZG 4224 // FLYmaker FLYF407ZG (STM32F407ZG) -#define BOARD_MKS_ROBIN2 4225 // MKS_ROBIN2 (STM32F407ZE) -#define BOARD_MKS_ROBIN_PRO_V2 4226 // MKS Robin Pro V2 (STM32F407VE) -#define BOARD_MKS_ROBIN_NANO_V3 4227 // MKS Robin Nano V3 (STM32F407VG) -#define BOARD_MKS_ROBIN_NANO_V3_1 4228 // MKS Robin Nano V3.1 (STM32F407VE) -#define BOARD_MKS_MONSTER8_V1 4229 // MKS Monster8 V1 (STM32F407VE) -#define BOARD_MKS_MONSTER8_V2 4230 // MKS Monster8 V2 (STM32F407VE) -#define BOARD_ANET_ET4 4231 // ANET ET4 V1.x (STM32F407VG) -#define BOARD_ANET_ET4P 4232 // ANET ET4P V1.x (STM32F407VG) -#define BOARD_FYSETC_CHEETAH_V20 4233 // FYSETC Cheetah V2.0 (STM32F401RC) -#define BOARD_TH3D_EZBOARD_V2 4234 // TH3D EZBoard v2.0 (STM32F405RG) -#define BOARD_OPULO_LUMEN_REV3 4235 // Opulo Lumen PnP Controller REV3 (STM32F407VE / STM32F407VG) -#define BOARD_MKS_ROBIN_NANO_V1_3_F4 4236 // MKS Robin Nano V1.3 and MKS Robin Nano-S V1.3 (STM32F407VE) -#define BOARD_MKS_EAGLE 4237 // MKS Eagle (STM32F407VE) -#define BOARD_ARTILLERY_RUBY 4238 // Artillery Ruby (STM32F401RC) -#define BOARD_FYSETC_SPIDER_V2_2 4239 // FYSETC Spider V2.2 (STM32F446VE) -#define BOARD_CREALITY_V24S1_301F4 4240 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4 -#define BOARD_OPULO_LUMEN_REV4 4241 // Opulo Lumen PnP Controller REV4 (STM32F407VE / STM32F407VG) -#define BOARD_FYSETC_SPIDER_KING407 4242 // FYSETC Spider King407 (STM32F407ZG) -#define BOARD_MKS_SKIPR_V1 4243 // MKS SKIPR v1.0 all-in-one board (STM32F407VE) -#define BOARD_TRONXY_V10 4244 // TRONXY V10 (STM32F446ZE) - -// -// ARM Cortex M7 -// - -#define BOARD_REMRAM_V1 5000 // RemRam v1 -#define BOARD_TEENSY41 5001 // Teensy 4.1 -#define BOARD_T41U5XBB 5002 // T41U5XBB Teensy 4.1 breakout board -#define BOARD_NUCLEO_F767ZI 5003 // ST NUCLEO-F767ZI Dev Board -#define BOARD_BTT_SKR_SE_BX_V2 5004 // BigTreeTech SKR SE BX V2.0 (STM32H743II) -#define BOARD_BTT_SKR_SE_BX_V3 5005 // BigTreeTech SKR SE BX V3.0 (STM32H743II) -#define BOARD_BTT_SKR_V3_0 5006 // BigTreeTech SKR V3.0 (STM32H743VG) -#define BOARD_BTT_SKR_V3_0_EZ 5007 // BigTreeTech SKR V3.0 EZ (STM32H743VG) +#define BOARD_ARMED 5200 // Arm'ed STM32F4-based controller +#define BOARD_RUMBA32_V1_0 5201 // RUMBA32 STM32F446VE based controller from Aus3D +#define BOARD_RUMBA32_V1_1 5202 // RUMBA32 STM32F446VE based controller from Aus3D +#define BOARD_RUMBA32_MKS 5203 // RUMBA32 STM32F446VE based controller from Makerbase +#define BOARD_RUMBA32_BTT 5204 // RUMBA32 STM32F446VE based controller from BIGTREETECH +#define BOARD_BLACK_STM32F407VE 5205 // BLACK_STM32F407VE +#define BOARD_BLACK_STM32F407ZE 5206 // BLACK_STM32F407ZE +#define BOARD_BTT_SKR_MINI_E3_V3_0_1 5207 // BigTreeTech SKR Mini E3 V3.0.1 (STM32F401RC) +#define BOARD_BTT_SKR_PRO_V1_1 5208 // BigTreeTech SKR Pro v1.1 (STM32F407ZG) +#define BOARD_BTT_SKR_PRO_V1_2 5209 // BigTreeTech SKR Pro v1.2 (STM32F407ZG) +#define BOARD_BTT_BTT002_V1_0 5210 // BigTreeTech BTT002 v1.0 (STM32F407VG) +#define BOARD_BTT_E3_RRF 5211 // BigTreeTech E3 RRF (STM32F407VG) +#define BOARD_BTT_SKR_V2_0_REV_A 5212 // BigTreeTech SKR v2.0 Rev A (STM32F407VG) +#define BOARD_BTT_SKR_V2_0_REV_B 5213 // BigTreeTech SKR v2.0 Rev B (STM32F407VG/STM32F429VG) +#define BOARD_BTT_GTR_V1_0 5214 // BigTreeTech GTR v1.0 (STM32F407IGT) +#define BOARD_BTT_OCTOPUS_V1_0 5215 // BigTreeTech Octopus v1.0 (STM32F446ZE) +#define BOARD_BTT_OCTOPUS_V1_1 5216 // BigTreeTech Octopus v1.1 (STM32F446ZE) +#define BOARD_BTT_OCTOPUS_PRO_V1_0 5217 // BigTreeTech Octopus Pro v1.0 (STM32F446ZE / STM32F429ZG) +#define BOARD_LERDGE_K 5218 // Lerdge K (STM32F407ZG) +#define BOARD_LERDGE_S 5219 // Lerdge S (STM32F407VE) +#define BOARD_LERDGE_X 5220 // Lerdge X (STM32F407VE) +#define BOARD_VAKE403D 5221 // VAkE 403D (STM32F446VE) +#define BOARD_FYSETC_S6 5222 // FYSETC S6 (STM32F446VE) +#define BOARD_FYSETC_S6_V2_0 5223 // FYSETC S6 v2.0 (STM32F446VE) +#define BOARD_FYSETC_SPIDER 5224 // FYSETC Spider (STM32F446VE) +#define BOARD_FLYF407ZG 5225 // FLYmaker FLYF407ZG (STM32F407ZG) +#define BOARD_MKS_ROBIN2 5226 // MKS_ROBIN2 (STM32F407ZE) +#define BOARD_MKS_ROBIN_PRO_V2 5227 // MKS Robin Pro V2 (STM32F407VE) +#define BOARD_MKS_ROBIN_NANO_V3 5228 // MKS Robin Nano V3 (STM32F407VG) +#define BOARD_MKS_ROBIN_NANO_V3_1 5229 // MKS Robin Nano V3.1 (STM32F407VE) +#define BOARD_MKS_MONSTER8_V1 5230 // MKS Monster8 V1 (STM32F407VE) +#define BOARD_MKS_MONSTER8_V2 5231 // MKS Monster8 V2 (STM32F407VE) +#define BOARD_ANET_ET4 5232 // ANET ET4 V1.x (STM32F407VG) +#define BOARD_ANET_ET4P 5233 // ANET ET4P V1.x (STM32F407VG) +#define BOARD_FYSETC_CHEETAH_V20 5234 // FYSETC Cheetah V2.0 (STM32F401RC) +#define BOARD_TH3D_EZBOARD_V2 5235 // TH3D EZBoard v2.0 (STM32F405RG) +#define BOARD_OPULO_LUMEN_REV3 5236 // Opulo Lumen PnP Controller REV3 (STM32F407VE / STM32F407VG) +#define BOARD_MKS_ROBIN_NANO_V1_3_F4 5237 // MKS Robin Nano V1.3 and MKS Robin Nano-S V1.3 (STM32F407VE) +#define BOARD_MKS_EAGLE 5238 // MKS Eagle (STM32F407VE) +#define BOARD_ARTILLERY_RUBY 5239 // Artillery Ruby (STM32F401RC) +#define BOARD_FYSETC_SPIDER_V2_2 5240 // FYSETC Spider V2.2 (STM32F446VE) +#define BOARD_CREALITY_V24S1_301F4 5241 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4 +#define BOARD_OPULO_LUMEN_REV4 5242 // Opulo Lumen PnP Controller REV4 (STM32F407VE / STM32F407VG) +#define BOARD_FYSETC_SPIDER_KING407 5243 // FYSETC Spider King407 (STM32F407ZG) +#define BOARD_MKS_SKIPR_V1 5244 // MKS SKIPR v1.0 all-in-one board (STM32F407VE) +#define BOARD_TRONXY_V10 5245 // TRONXY V10 (STM32F446ZE) + +// +// ARM Cortex-M7 +// + +#define BOARD_REMRAM_V1 6000 // RemRam v1 +#define BOARD_TEENSY41 6001 // Teensy 4.1 +#define BOARD_T41U5XBB 6002 // T41U5XBB Teensy 4.1 breakout board +#define BOARD_NUCLEO_F767ZI 6003 // ST NUCLEO-F767ZI Dev Board +#define BOARD_BTT_SKR_SE_BX_V2 6004 // BigTreeTech SKR SE BX V2.0 (STM32H743II) +#define BOARD_BTT_SKR_SE_BX_V3 6005 // BigTreeTech SKR SE BX V3.0 (STM32H743II) +#define BOARD_BTT_SKR_V3_0 6006 // BigTreeTech SKR V3.0 (STM32H743VG) +#define BOARD_BTT_SKR_V3_0_EZ 6007 // BigTreeTech SKR V3.0 EZ (STM32H743VG) // // Espressif ESP32 WiFi // -#define BOARD_ESPRESSIF_ESP32 6000 // Generic ESP32 -#define BOARD_MRR_ESPA 6001 // MRR ESPA based on ESP32 (native pins only) -#define BOARD_MRR_ESPE 6002 // MRR ESPE based on ESP32 (with I2S stepper stream) -#define BOARD_E4D_BOX 6003 // E4d@BOX -#define BOARD_RESP32_CUSTOM 6004 // Rutilea ESP32 custom board -#define BOARD_FYSETC_E4 6005 // FYSETC E4 -#define BOARD_PANDA_ZHU 6006 // Panda_ZHU -#define BOARD_PANDA_M4 6007 // Panda_M4 -#define BOARD_MKS_TINYBEE 6008 // MKS TinyBee based on ESP32 (with I2S stepper stream) -#define BOARD_ENWI_ESPNP 6009 // enwi ESPNP based on ESP32 (with I2S stepper stream) +#define BOARD_ESPRESSIF_ESP32 7000 // Generic ESP32 +#define BOARD_MRR_ESPA 7001 // MRR ESPA based on ESP32 (native pins only) +#define BOARD_MRR_ESPE 7002 // MRR ESPE based on ESP32 (with I2S stepper stream) +#define BOARD_E4D_BOX 7003 // E4d@BOX +#define BOARD_RESP32_CUSTOM 7004 // Rutilea ESP32 custom board +#define BOARD_FYSETC_E4 7005 // FYSETC E4 +#define BOARD_PANDA_ZHU 7006 // Panda_ZHU +#define BOARD_PANDA_M4 7007 // Panda_M4 +#define BOARD_MKS_TINYBEE 7008 // MKS TinyBee based on ESP32 (with I2S stepper stream) +#define BOARD_ENWI_ESPNP 7009 // enwi ESPNP based on ESP32 (with I2S stepper stream) // -// SAMD51 ARM Cortex M4 +// SAMD51 ARM Cortex-M4 // -#define BOARD_AGCM4_RAMPS_144 6100 // RAMPS 1.4.4 -#define BOARD_BRICOLEMON_V1_0 6101 // Bricolemon -#define BOARD_BRICOLEMON_LITE_V1_0 6102 // Bricolemon Lite +#define BOARD_AGCM4_RAMPS_144 7100 // RAMPS 1.4.4 +#define BOARD_BRICOLEMON_V1_0 7101 // Bricolemon +#define BOARD_BRICOLEMON_LITE_V1_0 7102 // Bricolemon Lite // -// SAMD21 ARM Cortex M4 +// SAMD21 ARM Cortex-M4 // -#define BOARD_MINITRONICS20 6103 // Minitronics v2.0 +#define BOARD_MINITRONICS20 7103 // Minitronics v2.0 // // Custom board diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index e0ec241faf9c..18bb7dba5827 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -545,6 +545,16 @@ #include "stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h" // STM32F1 env:STM32F103RC_btt env:STM32F103RC_btt_USB env:STM32F103RE_btt env:STM32F103RE_btt_USB env:STM32F103RC_btt_maple env:STM32F103RC_btt_USB_maple env:STM32F103RE_btt_maple env:STM32F103RE_btt_USB_maple #elif MB(BTT_SKR_MINI_E3_V3_0) #include "stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer +#elif MB(BTT_MANTA_M4P_V1_0) + #include "stm32g0/pins_BTT_MANTA_M4P_V1_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer +#elif MB(BTT_MANTA_M5P_V1_0) + #include "stm32g0/pins_BTT_MANTA_M5P_V1_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer +#elif MB(BTT_MANTA_E3_EZ_V1_0) + #include "stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h" // STM32G0 env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer +#elif MB(BTT_MANTA_M8P_V1_0) + #include "stm32g0/pins_BTT_MANTA_M8P_V1_0.h" // STM32G0 env:STM32G0B1VE_btt env:STM32G0B1VE_btt_xfer +#elif MB(BTT_MANTA_M8P_V1_1) + #include "stm32g0/pins_BTT_MANTA_M8P_V1_1.h" // STM32G0 env:STM32G0B1VE_btt env:STM32G0B1VE_btt_xfer #elif MB(BTT_SKR_MINI_E3_V3_0_1) #include "stm32f4/pins_BTT_SKR_MINI_E3_V3_0_1.h"// STM32F4 env:STM32F401RC_btt #elif MB(BTT_SKR_MINI_MZ_V1_0) diff --git a/Marlin/src/pins/stm32g0/env_validate.h b/Marlin/src/pins/stm32g0/env_validate.h new file mode 100644 index 000000000000..a7be76bd8bb1 --- /dev/null +++ b/Marlin/src/pins/stm32g0/env_validate.h @@ -0,0 +1,26 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#if NOT_TARGET(STM32G0xx) || NOT_TARGET(STM32G0B1xx) + #error "Oops! Select an STM32G0 board in 'Tools > Board.'" +#endif diff --git a/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h b/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h index fc2be5401e10..cdd85a6d751c 100644 --- a/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h +++ b/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h @@ -21,6 +21,8 @@ */ #pragma once +#include "env_validate.h" + /** CAUTION ** * This board definition is to facilitate support for a Filament Extrusion * devices, used to convert waste plastic into 3D printable filament. diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h new file mode 100644 index 000000000000..54c2c4c77b2d --- /dev/null +++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h @@ -0,0 +1,340 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "env_validate.h" + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "BTT Manta E3 EZ V1.0" +#endif + +#define USES_DIAG_JUMPERS + +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// +// EEPROM +// +#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) + #undef NO_EEPROM_SELECTED + #ifndef FLASH_EEPROM_EMULATION + #define FLASH_EEPROM_EMULATION + #endif + #define EEPROM_PAGE_SIZE (0x800UL) // 2K + #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL) + #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE +#endif + +// +// Servos +// +#define SERVO0_PIN PA7 // BLTouch + +// +// Probe enable +// +#if ENABLED(PROBE_ENABLE_DISABLE) + #ifndef PROBE_ENABLE_PIN + #define PROBE_ENABLE_PIN SERVO0_PIN + #endif +#endif + +// +// Trinamic StallGuard pins +// +#define X_DIAG_PIN PC4 // X-STOP +#define Y_DIAG_PIN PB0 // Y-STOP +#define Z_DIAG_PIN PC6 // Z-STOP +#define E0_DIAG_PIN PC5 // E0-DET +#define E1_DIAG_PIN PB1 // E1-DET + +// +// Limit Switches +// +#define X_STOP_PIN X_DIAG_PIN // X-STOP +#define Y_STOP_PIN Y_DIAG_PIN // Y-STOP +#define Z_STOP_PIN Z_DIAG_PIN // Z-STOP + +// +// Z Probe (when not Z_STOP_PIN) +// +#define Z_MIN_PROBE_PIN PA6 // BLTouch + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN E0_DIAG_PIN // E0-DET +#endif +#ifndef FIL_RUNOUT2_PIN + #define FIL_RUNOUT2_PIN E1_DIAG_PIN // E1-DET +#endif + +// +// Power Supply Control +// +#ifndef PS_ON_PIN + #define PS_ON_PIN PA9 // PS-ON +#endif + +// +// Power Loss Detection +// +#ifndef POWER_LOSS_PIN + #define POWER_LOSS_PIN PB9 // PWRDET +#endif + +// +// Steppers +// +#define X_STEP_PIN PA14 +#define X_DIR_PIN PA10 +#define X_ENABLE_PIN PA13 +#ifndef X_CS_PIN + #define X_CS_PIN PB8 +#endif + +#define Y_STEP_PIN PC8 +#define Y_DIR_PIN PA15 +#define Y_ENABLE_PIN PC14 +#ifndef Y_CS_PIN + #define Y_CS_PIN PC9 +#endif + +#define Z_STEP_PIN PD2 +#define Z_DIR_PIN PD4 +#define Z_ENABLE_PIN PD3 +#ifndef Z_CS_PIN + #define Z_CS_PIN PD0 +#endif + +#define E0_STEP_PIN PD5 +#define E0_DIR_PIN PD6 +#define E0_ENABLE_PIN PB3 +#ifndef E0_CS_PIN + #define E0_CS_PIN PD1 +#endif + +#define E1_STEP_PIN PB7 +#define E1_DIR_PIN PB6 +#define E1_ENABLE_PIN PB4 +#ifndef E1_CS_PIN + #define E1_CS_PIN PB5 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PC12 // Shared with SPI header, Pin 5 (SPI3) + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PC11 // Shared with SPI header, Pin 6 (SPI3) + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PC10 // Shared with SPI header, Pin 4 (SPI3) + #endif +#endif + +#if HAS_TMC_UART + #define X_SERIAL_TX_PIN PB8 // X_CS_PIN + #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN + + #define Y_SERIAL_TX_PIN PC9 // Y_CS_PIN + #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN + + #define Z_SERIAL_TX_PIN PD0 // Z_CS_PIN + #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN + + #define E0_SERIAL_TX_PIN PD1 // E0_CS_PIN + #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN + + #define E1_SERIAL_TX_PIN PB5 // E1_CS_PIN + #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA4 // Analog Input "TH0" +#define TEMP_1_PIN PA5 // Analog Input "TH1" +#define TEMP_BED_PIN PA3 // Analog Input "TB" + +// +// Heaters / Fans +// +#define HEATER_0_PIN PB11 // "HE0" +#define HEATER_1_PIN PB10 // "HE1" +#define HEATER_BED_PIN PB2 // "HB" + +#define FAN_PIN PA8 // "FAN0" +#define FAN1_PIN PB15 // "FAN1" +#define FAN2_PIN PB14 // "FAN2" + +// +// Auto fans +// +#if HOTENDS == 2 + #ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN FAN1_PIN + #endif + #ifndef E1_AUTO_FAN_PIN + #define E1_AUTO_FAN_PIN FAN2_PIN + #endif +#else + #ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN FAN1_PIN + #endif + #ifndef CONTROLLER_FAN_PIN + #define CONTROLLER_FAN_PIN FAN2_PIN + #endif +#endif + +/** + * Manta E3 EZ V1.0 + * ------ + * (BEEPER) PC1 | 1 2 | PC2 (BTN_ENC) + * (BTN_EN1) PC3 | 3 4 | RESET + * (BTN_EN2) PC0 5 6 | PA0 (LCD_D4) + * (LCD_RS) PA2 | 7 8 | PA1 (LCD_EN) + * GND | 9 10 | 5V + * ------ + * EXP1 + */ +#define EXP1_01_PIN PC1 +#define EXP1_02_PIN PC2 +#define EXP1_03_PIN PC3 +#define EXP1_04_PIN -1 +#define EXP1_05_PIN PC0 +#define EXP1_06_PIN PA0 +#define EXP1_07_PIN PA2 +#define EXP1_08_PIN PA1 +#define EXP1_09_PIN -1 +#define EXP1_10_PIN -1 + +#if HAS_DWIN_E3V2 || IS_DWIN_MARLINUI + #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING + #error "CAUTION! Ender-3 V2 display requires a custom cable with TX = PA0, RX = PC2. See 'pins_BTT_MANTA_E3_EZ_V1_0.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)" + #endif + + /** + * Ender-3 V2 display Manta E3 EZ V1.0 Ender-3 V2 display --> Manta E3 EZ V1.0 + * ------ ------ RX 3 --> 5 P0_15 + * -- | 1 2 | -- (BEEPER) PC1 | 1 2 | PC2 (BTN_ENC) TX 4 --> 9 P0_16 + * (MANTA TX1) RX | 3 4 | TX (MANTA RX1) (BTN_EN1) PC3 | 3 4 | RESET BEEPER 6 --> 10 P2_08 + * (BTN_ENC) ENT 5 6 | BEEPER (BTN_EN2) PC0 5 6 | PA0 (LCD_D4) + * (BTN_E2) B | 7 8 | A (BTN_E1) (LCD_RS) PA2 | 7 8 | PA1 (LCD_EN) + * GND | 9 10 | 5V GND | 9 10 | 5V + * ------ ------ + */ + + #define BEEPER_PIN EXP1_01_PIN + #define BTN_EN1 EXP1_08_PIN + #define BTN_EN2 EXP1_07_PIN + #define BTN_ENC EXP1_05_PIN + +#elif HAS_WIRED_LCD + + #if ENABLED(CR10_STOCKDISPLAY) + + #define BEEPER_PIN EXP1_01_PIN + + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_05_PIN + #define BTN_ENC EXP1_02_PIN + + #define LCD_PINS_RS EXP1_07_PIN + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN + + #elif ENABLED(ZONESTAR_LCD) // ANET A8 LCD Controller - Must convert to 3.3V - CONNECTING TO 5V WILL DAMAGE THE BOARD! + + #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING + #error "CAUTION! ZONESTAR_LCD requires wiring modifications. See 'pins_BTT_MANTA_E3_EZ_V1_0.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)" + #endif + + #define LCD_PINS_RS EXP1_06_PIN + #define LCD_PINS_ENABLE EXP1_02_PIN + #define LCD_PINS_D4 EXP1_07_PIN + #define LCD_PINS_D5 EXP1_05_PIN + #define LCD_PINS_D6 EXP1_03_PIN + #define LCD_PINS_D7 EXP1_01_PIN + #define ADC_KEYPAD_PIN PA7 // Repurpose default SERVO0_PIN for ADC - CONNECTING TO 5V WILL DAMAGE THE BOARD! + + #elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY) + + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_05_PIN + #define BTN_ENC EXP1_02_PIN + + #define DOGLCD_CS EXP1_07_PIN + #define DOGLCD_A0 EXP1_06_PIN + #define DOGLCD_SCK EXP1_01_PIN + #define DOGLCD_MOSI EXP1_08_PIN + #define FORCE_SOFT_SPI + #define LCD_BACKLIGHT_PIN -1 + + #else + + #error "Only ZONESTAR_LCD, MKS_MINI_12864, ENDER2_STOCKDISPLAY, and CR10_STOCKDISPLAY are currently supported on the BTT_MANTA_E3_EZ_V1_0." + + #endif + +#endif // HAS_WIRED_LCD + +// +// SD Support +// + +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +#define SD_DETECT_PIN -1 + +#if SD_CONNECTION_IS(LCD) && (BOTH(TOUCH_UI_FTDI_EVE, LCD_FYSETC_TFT81050) || IS_TFTGLCD_PANEL) + #define SD_SS_PIN EXP1_05_PIN +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "SD CUSTOM_CABLE is not compatible with Manta E3 EZ." +#endif + +#define ONBOARD_SPI_DEVICE 3 // SPI3 -> used only by HAL/STM32F1... +#define ONBOARD_SD_CS_PIN PC13 // Chip select for "System" SD card + +#define ENABLE_SPI3 +#define SDSS ONBOARD_SD_CS_PIN +#define SD_SS_PIN ONBOARD_SD_CS_PIN +#define SD_SCK_PIN PC10 +#define SD_MISO_PIN PC11 +#define SD_MOSI_PIN PC12 + +// +// NeoPixel LED +// +#ifndef NEOPIXEL_PIN + #define NEOPIXEL_PIN PC7 // RGB +#endif diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M4P_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M4P_V1_0.h new file mode 100644 index 000000000000..876475f88355 --- /dev/null +++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M4P_V1_0.h @@ -0,0 +1,313 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "env_validate.h" + +//#define BOARD_CUSTOM_BUILD_FLAGS -DTONE_CHANNEL=4 -DTONE_TIMER=4 -DTIMER_TONE=4 + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "BTT Manta M4P V1.0" +#endif + +#define USES_DIAG_JUMPERS + +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// +// EEPROM +// +#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) + #undef NO_EEPROM_SELECTED + #ifndef FLASH_EEPROM_EMULATION + #define FLASH_EEPROM_EMULATION + #endif + #define EEPROM_PAGE_SIZE (0x800UL) // 2K + #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL) + #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE +#endif + +// +// Servos +// +#define SERVO0_PIN PA1 // SERVOS + +// +// Probe enable +// +#if ENABLED(PROBE_ENABLE_DISABLE) + #ifndef PROBE_ENABLE_PIN + #define PROBE_ENABLE_PIN SERVO0_PIN + #endif +#endif + +// +// Limit Switches +// +#define X_STOP_PIN PC0 // X-STOP +#define Y_STOP_PIN PC1 // Y-STOP +#define Z_STOP_PIN PC2 // Z-STOP + +// +// Z Probe must be this pin +// +#define Z_MIN_PROBE_PIN PC14 // PROBE + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PC15 // E0-STOP +#endif + +// +// Steppers +// +#define X_STEP_PIN PC6 +#define X_DIR_PIN PA14 +#define X_ENABLE_PIN PC7 +#ifndef X_CS_PIN + #define X_CS_PIN PB12 +#endif + +#define Y_STEP_PIN PB10 +#define Y_DIR_PIN PB2 +#define Y_ENABLE_PIN PB11 +#ifndef Y_CS_PIN + #define Y_CS_PIN PC10 +#endif + +#define Z_STEP_PIN PB0 +#define Z_DIR_PIN PC5 +#define Z_ENABLE_PIN PB1 +#ifndef Z_CS_PIN + #define Z_CS_PIN PC9 +#endif + +#define E0_STEP_PIN PB3 +#define E0_DIR_PIN PB4 +#define E0_ENABLE_PIN PD5 +#ifndef E0_CS_PIN + #define E0_CS_PIN PA13 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PB15 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PB14 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PB13 + #endif +#endif + +#if HAS_TMC_UART + #define X_SERIAL_TX_PIN PB12 + #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN + + #define Y_SERIAL_TX_PIN PC10 + #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN + + #define Z_SERIAL_TX_PIN PC9 + #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN + + #define E0_SERIAL_TX_PIN PA13 + #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA0 // Analog Input "TH0" +#define TEMP_BED_PIN PC4 // Analog Input "TB0" + +// +// Heaters / Fans +// +#define HEATER_0_PIN PC8 // "HE" +#define HEATER_BED_PIN PD8 // "HB" + +#define FAN_PIN PD2 // "FAN0" +#define FAN1_PIN PD3 // "FAN1" +#define FAN2_PIN PD4 // "FAN2" + +/** + * ------ ------ + * (BEEPER) PD6 | 1 2 | PB8 (BTN_ENC) (MISO) PB14 | 1 2 | PB13 (SCK) + * (LCD_EN) PB9 | 3 4 | PC3 (LCD_RS) (BTN_EN1) PC11 | 3 4 | PA8 (SD_SS) + * (LCD_D4) PA15 | 5 6 PA10 (LCD_D5) (BTN_EN2) PC12 | 5 6 PB15 (MOSI) + * (LCD_D6) PA9 | 7 8 | PB5 (LCD_D7) (SD_DETECT) PC13 | 7 8 | RESET + * GND | 9 10 | 5V GND | 9 10 | -- + * ------ ------ + * EXP1 EXP2 + */ +#define EXP1_01_PIN PD6 +#define EXP1_02_PIN PB8 +#define EXP1_03_PIN PB9 +#define EXP1_04_PIN PC3 +#define EXP1_05_PIN PA15 +#define EXP1_06_PIN PA10 +#define EXP1_07_PIN PA9 +#define EXP1_08_PIN PB5 + +#define EXP2_01_PIN PB14 +#define EXP2_02_PIN PB13 +#define EXP2_03_PIN PC11 +#define EXP2_04_PIN PA8 +#define EXP2_05_PIN PC12 +#define EXP2_06_PIN PB15 +#define EXP2_07_PIN PC13 +#define EXP2_08_PIN -1 + +// +// Onboard SD card +// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2 +// +#if SD_CONNECTION_IS(LCD) + #define SDSS EXP2_04_PIN + #define SD_SS_PIN SDSS + #define SD_SCK_PIN EXP2_02_PIN + #define SD_MISO_PIN EXP2_01_PIN + #define SD_MOSI_PIN EXP2_06_PIN + #define SD_DETECT_PIN EXP2_07_PIN +#elif SD_CONNECTION_IS(ONBOARD) + #define SD_SCK_PIN PA5 + #define SD_MISO_PIN PA6 + #define SD_MOSI_PIN PA7 + #define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card + #define SD_SS_PIN ONBOARD_SD_CS_PIN +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + +// +// LCDs and Controllers +// +#if IS_TFTGLCD_PANEL + + #if ENABLED(TFTGLCD_PANEL_SPI) + #define TFTGLCD_CS EXP2_03_PIN + #endif + +#elif HAS_WIRED_LCD + + #define BEEPER_PIN EXP1_01_PIN + #define BTN_ENC EXP1_02_PIN + + #if ENABLED(CR10_STOCKDISPLAY) + + #define LCD_PINS_RS EXP1_07_PIN + + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_05_PIN + + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN + + #elif ENABLED(MKS_MINI_12864) + + #define DOGLCD_A0 EXP1_07_PIN + #define DOGLCD_CS EXP1_06_PIN + #define BTN_EN1 EXP2_03_PIN + #define BTN_EN2 EXP2_05_PIN + + #else + + #define LCD_PINS_RS EXP1_04_PIN + + #define BTN_EN1 EXP2_03_PIN + #define BTN_EN2 EXP2_05_PIN + + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN + + #if ENABLED(FYSETC_MINI_12864) + #define DOGLCD_CS EXP1_03_PIN + #define DOGLCD_A0 EXP1_04_PIN + //#define LCD_BACKLIGHT_PIN -1 + + #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally. + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN EXP1_06_PIN + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN EXP1_07_PIN + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN EXP1_08_PIN + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN EXP1_06_PIN + #endif + #endif // !FYSETC_MINI_12864 + + #if IS_ULTIPANEL + #define LCD_PINS_D5 EXP1_06_PIN + #define LCD_PINS_D6 EXP1_07_PIN + #define LCD_PINS_D7 EXP1_08_PIN + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + + #endif + +#endif // HAS_WIRED_LCD + +// Alter timing for graphical display +#if IS_U8GLIB_ST7920 + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 120 + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 80 + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 580 + #endif +#endif + +// +// NeoPixel LED +// +#ifndef NEOPIXEL_PIN + #define NEOPIXEL_PIN PD0 +#endif + +#ifndef NEOPIXEL2_PIN + #define NEOPIXEL2_PIN PD1 +#endif diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M5P_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M5P_V1_0.h new file mode 100644 index 000000000000..f4ce5a16d3b0 --- /dev/null +++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M5P_V1_0.h @@ -0,0 +1,341 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "env_validate.h" + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "BTT Manta M5P V1.0" +#endif + +#define USES_DIAG_JUMPERS + +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// +// EEPROM +// +#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) + #undef NO_EEPROM_SELECTED + #ifndef FLASH_EEPROM_EMULATION + #define FLASH_EEPROM_EMULATION + #endif + #define EEPROM_PAGE_SIZE (0x800UL) // 2K + #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL) + #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE +#endif + +// +// Servos +// +#define SERVO0_PIN PC15 // PROBE + +// +// Probe enable +// +#if ENABLED(PROBE_ENABLE_DISABLE) + #ifndef PROBE_ENABLE_PIN + #define PROBE_ENABLE_PIN SERVO0_PIN + #endif +#endif + +// +// Trinamic StallGuard pins +// +#define X_DIAG_PIN PD3 // MIN1 +#define Y_DIAG_PIN PD2 // MIN2 +#define Z_DIAG_PIN PC3 // MIN3 +#define E0_DIAG_PIN PC2 // MIN4 +#define E1_DIAG_PIN -1 + +// +// Limit Switches +// +#define X_STOP_PIN X_DIAG_PIN // MIN1 +#define Y_STOP_PIN Y_DIAG_PIN // MIN1 +#define Z_STOP_PIN Z_DIAG_PIN // MIN3 + +// +// Z Probe (when not Z_STOP_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN PC13 // PROBE + //#define Z_MIN_PROBE_PIN PC15 // IND-DET (with adjustable pullup set via jumper) +#endif + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN E0_DIAG_PIN // MIN4 +#endif + +// +// Steppers +// +#define X_STEP_PIN PC8 +#define X_DIR_PIN PC9 +#define X_ENABLE_PIN PA15 +#ifndef X_CS_PIN + #define X_CS_PIN PD9 +#endif + +#define Y_STEP_PIN PA10 +#define Y_DIR_PIN PA14 +#define Y_ENABLE_PIN PA13 +#ifndef Y_CS_PIN + #define Y_CS_PIN PD8 +#endif + +#define Z_STEP_PIN PC6 +#define Z_DIR_PIN PC7 +#define Z_ENABLE_PIN PA9 +#ifndef Z_CS_PIN + #define Z_CS_PIN PB10 +#endif + +#define E0_STEP_PIN PB12 +#define E0_DIR_PIN PB11 +#define E0_ENABLE_PIN PA8 +#ifndef E0_CS_PIN + #define E0_CS_PIN PB2 +#endif + +#define E1_STEP_PIN PB0 +#define E1_DIR_PIN PB1 +#define E1_ENABLE_PIN PC4 +#ifndef E1_CS_PIN + #define E1_CS_PIN PA6 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PB15 // Shared with SPI header, Pin 5 (SPI2) + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PB14 // Shared with SPI header, Pin 6 (SPI2) + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PB13 // Shared with SPI header, Pin 4 (SPI2) + #endif +#endif + +#if HAS_TMC_UART + #define X_SERIAL_TX_PIN PD9 // X_CS_PIN + #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN + + #define Y_SERIAL_TX_PIN PD8 // Y_CS_PIN + #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN + + #define Z_SERIAL_TX_PIN PB10 // Z_CS_PIN + #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN + + #define E0_SERIAL_TX_PIN PB2 // E0_CS_PIN + #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN + + #define E1_SERIAL_TX_PIN PA6 // E1_CS_PIN + #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA1 // Analog Input "TH0" +#define TEMP_1_PIN PA2 // Analog Input "TH1" +#define TEMP_BED_PIN PA0 // Analog Input "TB" + +// +// Heaters / Fans +// +#define HEATER_0_PIN PC5 // "HE0" +#define HEATER_1_PIN PA7 // "HE1" +#define HEATER_BED_PIN PA5 // "HB" + +#define FAN_PIN PA4 // "FAN0" +#define FAN1_PIN PA3 // "FAN1" + +// +// Auto fans +// +#ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN FAN1_PIN +#endif + +/** + * ------ ------ + * (BEEPER) PD5 | 1 2 | PD4 (BTN_ENC) (MISO) PB14 | 1 2 | PB13 (SCK) + * (LCD_EN) PB3 | 3 4 | PD6 (LCD_RS) (BTN_EN1) PB8 | 3 4 | PB9 (SD_SS) + * (LCD_D4) PB5 | 5 6 PB4 (LCD_D5) (BTN_EN2) PC10 | 5 6 PB15 (MOSI) + * (LCD_D6) PB7 | 7 8 | PB6 (LCD_D7) (SD_DETECT) PC12 | 7 8 | PF2 + * GND | 9 10 | 5V GND | 9 10 | -- + * ------ ------ + * EXP1 EXP2 + */ +#define EXP1_01_PIN PD5 +#define EXP1_02_PIN PD4 +#define EXP1_03_PIN PB3 +#define EXP1_04_PIN PD6 +#define EXP1_05_PIN PB5 +#define EXP1_06_PIN PB4 +#define EXP1_07_PIN PB7 +#define EXP1_08_PIN PB6 + +#define EXP2_01_PIN PB14 +#define EXP2_02_PIN PB13 +#define EXP2_03_PIN PB8 +#define EXP2_04_PIN PB9 +#define EXP2_05_PIN PC10 +#define EXP2_06_PIN PB15 +#define EXP2_07_PIN PC12 +#define EXP2_08_PIN -1 + +// +// Onboard SD card +// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2 +// +#if SD_CONNECTION_IS(LCD) + #define SDSS EXP2_04_PIN + #define SD_SS_PIN SDSS + #define SD_SCK_PIN EXP2_02_PIN + #define SD_MISO_PIN EXP2_01_PIN + #define SD_MOSI_PIN EXP2_06_PIN + #define SD_DETECT_PIN EXP2_07_PIN +#elif SD_CONNECTION_IS(ONBOARD) + #define SD_SCK_PIN PB13 + #define SD_MISO_PIN PB14 + #define SD_MOSI_PIN PB15 + #define ONBOARD_SD_CS_PIN PC1 // Chip select for "System" SD card + #define SD_SS_PIN ONBOARD_SD_CS_PIN +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + +// +// LCDs and Controllers +// +#if IS_TFTGLCD_PANEL + + #if ENABLED(TFTGLCD_PANEL_SPI) + #define TFTGLCD_CS EXP2_03_PIN + #endif + +#elif HAS_WIRED_LCD + + #define BEEPER_PIN EXP1_01_PIN + #define BTN_ENC EXP1_02_PIN + + #if ENABLED(CR10_STOCKDISPLAY) + + #define LCD_PINS_RS EXP1_07_PIN + + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_05_PIN + + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN + + #elif ENABLED(MKS_MINI_12864) + + #define DOGLCD_A0 EXP1_07_PIN + #define DOGLCD_CS EXP1_06_PIN + #define BTN_EN1 EXP2_03_PIN + #define BTN_EN2 EXP2_05_PIN + + #else + + #define LCD_PINS_RS EXP1_04_PIN + + #define BTN_EN1 EXP2_03_PIN + #define BTN_EN2 EXP2_05_PIN + + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN + + #if ENABLED(FYSETC_MINI_12864) + #define DOGLCD_CS EXP1_03_PIN + #define DOGLCD_A0 EXP1_04_PIN + //#define LCD_BACKLIGHT_PIN -1 + + #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally. + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN EXP1_06_PIN + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN EXP1_07_PIN + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN EXP1_08_PIN + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN EXP1_06_PIN + #endif + #endif // !FYSETC_MINI_12864 + + #if IS_ULTIPANEL + #define LCD_PINS_D5 EXP1_06_PIN + #define LCD_PINS_D6 EXP1_07_PIN + #define LCD_PINS_D7 EXP1_08_PIN + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + + #endif + +#endif // HAS_WIRED_LCD + +// Alter timing for graphical display +#if IS_U8GLIB_ST7920 + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 120 + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 80 + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 580 + #endif +#endif + +// +// NeoPixel LED +// +#ifndef NEOPIXEL_PIN + #define NEOPIXEL_PIN PC11 // RGB1 +#endif + +#ifndef NEOPIXEL2_PIN + #define NEOPIXEL2_PIN PC14 // RGB2 +#endif diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_0.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_0.h new file mode 100644 index 000000000000..4f8d30b6b7fa --- /dev/null +++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_0.h @@ -0,0 +1,79 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +// Include common Manta M8P pins +#include "pins_BTT_MANTA_M8P_common.h" + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "BTT Manta M8P V1.0" +#endif + +// +// Steppers +// + +#define E1_STEP_PIN PA10 // M6 +#define E1_DIR_PIN PD15 +#define E1_ENABLE_PIN PA15 +#ifndef E1_CS_PIN + #define E1_CS_PIN PF8 +#endif + +#define E2_STEP_PIN PD12 // M7 +#define E2_DIR_PIN PD11 +#define E2_ENABLE_PIN PD14 +#ifndef E2_CS_PIN + #define E2_CS_PIN PD13 +#endif + +#define E3_STEP_PIN PD10 // M8 +#define E3_DIR_PIN PD8 +#define E3_ENABLE_PIN PD9 +#ifndef E3_CS_PIN + #define E3_CS_PIN PC7 +#endif + +#if HAS_TMC_UART + #define E1_SERIAL_TX_PIN PF8 + #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN + + #define E2_SERIAL_TX_PIN PD13 + #define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN + + #define E3_SERIAL_TX_PIN PC7 + #define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// NeoPixel LED +// +#ifndef NEOPIXEL_PIN + #define NEOPIXEL_PIN PC6 +#endif + +#ifndef NEOPIXEL2_PIN + #define NEOPIXEL2_PIN PA9 +#endif diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_1.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_1.h new file mode 100644 index 000000000000..a21bb59e69c3 --- /dev/null +++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_V1_1.h @@ -0,0 +1,78 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +// Include common Manta M8P pins +#include "pins_BTT_MANTA_M8P_common.h" + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "BTT Manta M8P V1.1" +#endif + +// +// Steppers +// +#define E1_STEP_PIN PA10 // M6 +#define E1_DIR_PIN PA14 +#define E1_ENABLE_PIN PA15 +#ifndef E1_CS_PIN + #define E1_CS_PIN PF8 +#endif + +#define E2_STEP_PIN PD11 // M7 +#define E2_DIR_PIN PD9 +#define E2_ENABLE_PIN PD15 +#ifndef E2_CS_PIN + #define E2_CS_PIN PD14 +#endif + +#define E3_STEP_PIN PD8 // M8 +#define E3_DIR_PIN PC6 +#define E3_ENABLE_PIN PC7 +#ifndef E3_CS_PIN + #define E3_CS_PIN PD10 +#endif + +#if HAS_TMC_UART + #define E1_SERIAL_TX_PIN PF8 + #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN + + #define E2_SERIAL_TX_PIN PD14 + #define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN + + #define E3_SERIAL_TX_PIN PD10 + #define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// NeoPixel LED +// +#ifndef NEOPIXEL_PIN + #define NEOPIXEL_PIN PA9 +#endif + +#ifndef NEOPIXEL2_PIN + #define NEOPIXEL2_PIN PB15 +#endif diff --git a/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_common.h b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_common.h new file mode 100644 index 000000000000..0d4a74b6f95c --- /dev/null +++ b/Marlin/src/pins/stm32g0/pins_BTT_MANTA_M8P_common.h @@ -0,0 +1,397 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "env_validate.h" + +//#define BOARD_CUSTOM_BUILD_FLAGS -DTONE_CHANNEL=4 -DTONE_TIMER=4 -DTIMER_TONE=4 + +#define USES_DIAG_JUMPERS + +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// +// EEPROM +// +#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION) + #undef NO_EEPROM_SELECTED + #ifndef FLASH_EEPROM_EMULATION + #define FLASH_EEPROM_EMULATION + #endif + #define EEPROM_PAGE_SIZE (0x800UL) // 2K + #define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL) + #define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE +#endif + +// +// Servos +// +#define SERVO0_PIN PB1 // PROBE + +// +// Probe enable +// +#if ENABLED(PROBE_ENABLE_DISABLE) + #ifndef PROBE_ENABLE_PIN + #define PROBE_ENABLE_PIN SERVO0_PIN + #endif +#endif + +// +// Trinamic Stallguard pins +// +#define X_DIAG_PIN PF3 // MIN1 +#define Y_DIAG_PIN PF4 // MIN2 +#define Z_DIAG_PIN PF5 // MIN3 +#define Z2_DIAG_PIN PC0 // MIN4 +#define E0_DIAG_PIN PC1 // MIN5 +#define E1_DIAG_PIN PC2 // MIN6 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN PB2 // PROBE + //#define Z_MIN_PROBE_PIN PF6 // IND-PROBE (with adjustable voltage & pullup set via jumpers) +#endif + +// +// Check for additional used endstop pins +// +#if HAS_EXTRA_ENDSTOPS + #define _ENDSTOP_IS_ANY(ES) X2_USE_ENDSTOP == ES || Y2_USE_ENDSTOP == ES || Z2_USE_ENDSTOP == ES || Z3_USE_ENDSTOP == ES || Z4_USE_ENDSTOP == ES + #if _ENDSTOP_IS_ANY(_XMIN_) || _ENDSTOP_IS_ANY(_XMAX_) + #define NEEDS_X_MINMAX 1 + #endif + #if _ENDSTOP_IS_ANY(_YMIN_) || _ENDSTOP_IS_ANY(_YMAX_) + #define NEEDS_Y_MINMAX 1 + #endif + #undef _ENDSTOP_IS_ANY +#endif + +// +// Limit Switches +// +#ifdef X_STALL_SENSITIVITY + #define X_STOP_PIN X_DIAG_PIN + #if X_HOME_TO_MIN + #define X_MAX_PIN E0_DIAG_PIN // MIN5 + #else + #define X_MIN_PIN E0_DIAG_PIN // MIN5 + #endif +#elif EITHER(DUAL_X_CARRIAGE, NEEDS_X_MINMAX) + #ifndef X_MIN_PIN + #define X_MIN_PIN X_DIAG_PIN // MIN1 + #endif + #ifndef X_MAX_PIN + #define X_MAX_PIN E0_DIAG_PIN // MIN5 + #endif +#else + #define X_STOP_PIN X_DIAG_PIN // MIN1 +#endif + +#ifdef Y_STALL_SENSITIVITY + #define Y_STOP_PIN Y_DIAG_PIN + #if Y_HOME_TO_MIN + #define Y_MAX_PIN E1_DIAG_PIN // MIN6 + #else + #define Y_MIN_PIN E1_DIAG_PIN // MIN6 + #endif +#elif NEEDS_Y_MINMAX + #ifndef Y_MIN_PIN + #define Y_MIN_PIN Y_DIAG_PIN // MIN2 + #endif + #ifndef Y_MAX_PIN + #define Y_MAX_PIN E1_DIAG_PIN // MIN6 + #endif +#else + #define Y_STOP_PIN Y_DIAG_PIN // MIN2 +#endif + +#define Z_STOP_PIN Z_DIAG_PIN // MIN3 + +#undef NEEDS_X_MINMAX +#undef NEEDS_Y_MINMAX + +// +// Filament Runout Sensors +// +#define FIL_RUNOUT_PIN PC1 // MIN5 +#define FIL_RUNOUT2_PIN PC2 // MIN6 + +#ifndef PS_ON_PIN + #define PS_ON_PIN PC3 // PS-ON +#endif + +// +// Steppers +// +#define X_STEP_PIN PE2 // M1 +#define X_DIR_PIN PB4 +#define X_ENABLE_PIN PC11 +#ifndef X_CS_PIN + #define X_CS_PIN PC10 +#endif + +#define Y_STEP_PIN PF12 // M2 +#define Y_DIR_PIN PF11 +#define Y_ENABLE_PIN PB3 +#ifndef Y_CS_PIN + #define Y_CS_PIN PF13 +#endif + +#define Z_STEP_PIN PD7 // M3 +#define Z_DIR_PIN PD6 +#define Z_ENABLE_PIN PF10 +#ifndef Z_CS_PIN + #define Z_CS_PIN PF9 +#endif + +#define Z2_STEP_PIN PD3 // M4 +#define Z2_DIR_PIN PD2 +#define Z2_ENABLE_PIN PD5 +#ifndef Z2_CS_PIN + #define Z2_CS_PIN PD4 +#endif + +#define E0_STEP_PIN PC9 // M5 +#define E0_DIR_PIN PC8 +#define E0_ENABLE_PIN PD1 +#ifndef E0_CS_PIN + #define E0_CS_PIN PD0 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PA7 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PA6 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PA5 + #endif +#endif + +#if HAS_TMC_UART + #define X_SERIAL_TX_PIN PC10 + #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN + + #define Y_SERIAL_TX_PIN PF13 + #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN + + #define Z_SERIAL_TX_PIN PF9 + #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN + + #define Z2_SERIAL_TX_PIN PD4 + #define Z2_SERIAL_RX_PIN Z2_SERIAL_TX_PIN + + #define E0_SERIAL_TX_PIN PD0 + #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +// +// Temperature Sensors +// +#define TEMP_BED_PIN PA0 // TB +#define TEMP_0_PIN PA1 // TH0 +#define TEMP_1_PIN PA2 // TH1 +#define TEMP_2_PIN PA3 // TH2 +#define TEMP_3_PIN PA4 // TH3 + +// +// Heaters / Fans +// +#define HEATER_BED_PIN PB7 // BED-OUT +#define HEATER_0_PIN PE3 // HE0 +#define HEATER_1_PIN PB5 // HE1 +#define HEATER_2_PIN PB6 // HE2 +#define HEATER_3_PIN PE1 // HE3 + +#define FAN_PIN PE6 // FAN0 +#define FAN1_PIN PE0 // FAN1 +#define FAN2_PIN PC12 // FAN2 +#define FAN3_PIN PE5 // FAN3 +#define FAN4_PIN PE4 // FAN4 +#define FAN5_PIN PB8 // FAN5 +#define FAN6_PIN PB9 // FAN6 + +// +// SD Support +// +#ifndef SDCARD_CONNECTION + #if HAS_WIRED_LCD + #define SDCARD_CONNECTION LCD + #else + #define SDCARD_CONNECTION ONBOARD + #endif +#endif + +/** + * ------ ------ + * (BEEPER) PE9 | 1 2 | PE10 (BTN_ENC) (MISO) PB14 | 1 2 | PB13 (SCK) + * (LCD_EN) PE11 | 3 4 | PE12 (LCD_RS) (BTN_EN1) PF7 | 3 4 | PB12 (SD_SS) + * (LCD_D4) PE13 | 5 6 PE14 (LCD_D5) (BTN_EN2) PE7 | 5 6 PB11 (MOSI) + * (LCD_D6) PE15 | 7 8 | PB10 (LCD_D7) (SD_DETECT) PE8 | 7 8 | RESET + * GND | 9 10 | 5V GND | 9 10 | -- + * ------ ------ + * EXP1 EXP2 + */ +#define EXP1_01_PIN PE9 +#define EXP1_02_PIN PE10 +#define EXP1_03_PIN PE11 +#define EXP1_04_PIN PE12 +#define EXP1_05_PIN PE13 +#define EXP1_06_PIN PE14 +#define EXP1_07_PIN PE15 +#define EXP1_08_PIN PB10 + +#define EXP2_01_PIN PB14 +#define EXP2_02_PIN PB13 +#define EXP2_03_PIN PF7 +#define EXP2_04_PIN PB12 +#define EXP2_05_PIN PE7 +#define EXP2_06_PIN PB11 +#define EXP2_07_PIN PE8 +#define EXP2_08_PIN -1 + +// +// Onboard SD card +// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2 +// +#if SD_CONNECTION_IS(LCD) + #define SDSS EXP2_04_PIN + #define SD_SS_PIN SDSS + #define SD_SCK_PIN EXP2_02_PIN + #define SD_MISO_PIN EXP2_01_PIN + #define SD_MOSI_PIN EXP2_06_PIN + #define SD_DETECT_PIN EXP2_07_PIN +#elif SD_CONNECTION_IS(ONBOARD) + #define SD_DETECT_PIN PE8 + #define SD_SCK_PIN PB13 + #define SD_MISO_PIN PB14 + #define SD_MOSI_PIN PB11 + #define ONBOARD_SD_CS_PIN PB14 // Chip select for "System" SD card + #define SD_SS_PIN ONBOARD_SD_CS_PIN +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + +// +// LCDs and Controllers +// +#if IS_TFTGLCD_PANEL + + #if ENABLED(TFTGLCD_PANEL_SPI) + #define TFTGLCD_CS EXP2_03_PIN + #endif + +#elif HAS_WIRED_LCD + + #define BEEPER_PIN EXP1_01_PIN + #define BTN_ENC EXP1_02_PIN + + #if ENABLED(CR10_STOCKDISPLAY) + + #define LCD_PINS_RS EXP1_07_PIN + + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_05_PIN + + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN + + #elif ENABLED(MKS_MINI_12864) + + #define DOGLCD_A0 EXP1_07_PIN + #define DOGLCD_CS EXP1_06_PIN + #define BTN_EN1 EXP2_03_PIN + #define BTN_EN2 EXP2_05_PIN + + #else + + #define LCD_PINS_RS EXP1_04_PIN + + #define BTN_EN1 EXP2_03_PIN + #define BTN_EN2 EXP2_05_PIN + + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN + + #if ENABLED(FYSETC_MINI_12864) + #define DOGLCD_CS EXP1_03_PIN + #define DOGLCD_A0 EXP1_04_PIN + //#define LCD_BACKLIGHT_PIN -1 + + #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally. + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN EXP1_06_PIN + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN EXP1_07_PIN + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN EXP1_08_PIN + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN EXP1_06_PIN + #endif + #endif // !FYSETC_MINI_12864 + + #if IS_ULTIPANEL + #define LCD_PINS_D5 EXP1_06_PIN + #define LCD_PINS_D6 EXP1_07_PIN + #define LCD_PINS_D7 EXP1_08_PIN + + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + + #endif + + #endif + +#endif // HAS_WIRED_LCD + +// Alter timing for graphical display +#if IS_U8GLIB_ST7920 + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 120 + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 80 + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 580 + #endif +#endif diff --git a/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h b/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h index f931d9924acf..f71b7b40ebd1 100644 --- a/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h +++ b/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h @@ -21,6 +21,8 @@ */ #pragma once +#include "env_validate.h" + //#define BOARD_CUSTOM_BUILD_FLAGS -DTONE_CHANNEL=4 -DTONE_TIMER=4 -DTIMER_TONE=4 #ifndef BOARD_INFO_NAME diff --git a/buildroot/share/PlatformIO/boards/marlin_STM32G0B1VE.json b/buildroot/share/PlatformIO/boards/marlin_STM32G0B1VE.json new file mode 100644 index 000000000000..a3ac6ea6793a --- /dev/null +++ b/buildroot/share/PlatformIO/boards/marlin_STM32G0B1VE.json @@ -0,0 +1,47 @@ +{ + "build": { + "core": "stm32", + "cpu": "cortex-m0plus", + "extra_flags": "-DSTM32G0xx -DSTM32G0B1xx", + "f_cpu": "64000000L", + "framework_extra_flags": { + "arduino": "-D__CORTEX_SC=0" + }, + "mcu": "stm32g0b1vet6", + "product_line": "STM32G0B1xx", + "variant": "MARLIN_G0B1VE" + }, + "debug": { + "default_tools": [ + "stlink" + ], + "jlink_device": "STM32G0B1VE", + "onboard_tools": [ + "stlink" + ], + "openocd_target": "stm32g0x", + "svd_path": "STM32G0B1.svd" + }, + "frameworks": [ + "arduino", + "cmsis", + "libopencm3", + "stm32cube", + "zephyr" + ], + "name": "STM32G0B1VE", + "upload": { + "maximum_ram_size": 147456, + "maximum_size": 524288, + "protocol": "stlink", + "protocols": [ + "stlink", + "jlink", + "cmsis-dap", + "blackmagic", + "mbed" + ] + }, + "url": "https://www.st.com/content/st_com/en/products/microcontrollers-microprocessors/stm32-32-bit-arm-cortex-mcus/stm32-mainstream-mcus/stm32g0-series/stm32g0x1.html", + "vendor": "ST" +} diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c index eb95de1495f7..3187367a2d99 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/PeripheralPins.c @@ -218,6 +218,7 @@ WEAK const PinMap PinMap_UART_TX[] = { {PC_12, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, {PD_3, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, {PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)}, + {PD_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, {PF_2, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)}, {NC, NP, 0} }; @@ -252,6 +253,7 @@ WEAK const PinMap PinMap_UART_RX[] = { {PC_11_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART4)}, {PD_2, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, {PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)}, + {PD_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, {NC, NP, 0} }; #endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp index d18509f35f71..fa4ebfa71329 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.cpp @@ -130,14 +130,7 @@ WEAK void SystemClock_Config(void) RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; // Reset clock registers (in case bootloader has changed them) - RCC->CR |= RCC_CR_HSION; - while (!(RCC->CR & RCC_CR_HSIRDY)) - ; - RCC->CFGR = 0x00000000; - RCC->CR = RCC_CR_HSION; - while (RCC->CR & RCC_CR_PLLRDY) - ; - RCC->PLLCFGR = 0x00001000; + SystemInit(); /** Configure the main internal regulator output voltage */ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h index 6a26baff45db..23cecd371a28 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h @@ -158,6 +158,9 @@ #endif // UART Definitions +//#define ENABLE_HWSERIAL1 done automatically by the #define SERIAL_UART_INSTANCE below +#define ENABLE_HWSERIAL3 + #ifndef SERIAL_UART_INSTANCE #define SERIAL_UART_INSTANCE 2 #endif @@ -171,6 +174,15 @@ #define PIN_SERIAL_TX PA2 #endif +// Optional PIN_SERIALn_RX and PIN_SERIALn_TX where 'n' is the U(S)ART number +// Used when user instantiate a hardware Serial using its peripheral name. +// Example: HardwareSerial mySerial(USART3); +// will use PIN_SERIAL3_RX and PIN_SERIAL3_TX if defined. +#define PIN_SERIAL1_RX PA3 +#define PIN_SERIAL1_TX PA2 +#define PIN_SERIAL3_RX PD9 +#define PIN_SERIAL3_TX PD8 + /*---------------------------------------------------------------------------- * Arduino objects - C++ only *----------------------------------------------------------------------------*/ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PeripheralPins.c new file mode 100644 index 000000000000..a6b1e4423718 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PeripheralPins.c @@ -0,0 +1,480 @@ +/* + ******************************************************************************* + * Copyright (c) 2020-2021, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + */ +/* + * Automatically generated from STM32G0B1V(B-C-E)Ix.xml, STM32G0B1V(B-C-E)Tx.xml + * STM32G0B1V(C-E)Ix.xml, STM32G0B1V(C-E)Tx.xml + * STM32G0C1V(C-E)Ix.xml, STM32G0C1V(C-E)Tx.xml + * CubeMX DB release 6.0.30 + */ +#if !defined(CUSTOM_PERIPHERAL_PINS) +#include "Arduino.h" +#include "PeripheralPins.h" + +/* ===== + * Notes: + * - The pins mentioned Px_y_ALTz are alternative possibilities which use other + * HW peripheral instances. You can use them the same way as any other "normal" + * pin (i.e. analogWrite(PA7_ALT1, 128);). + * + * - Commented lines are alternative possibilities which are not used per default. + * If you change them, you will have to know what you do + * ===== + */ + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +WEAK const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 + {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 + {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 + {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 + {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 + {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 + {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 + {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 + {PB_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 + {PB_10, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 + {PB_11, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15 + {PB_12, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 16, 0)}, // ADC1_IN16 + {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 17, 0)}, // ADC1_IN17 + {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 18, 0)}, // ADC1_IN18 + {NC, NP, 0} +}; +#endif + +//*** DAC *** + +#ifdef HAL_DAC_MODULE_ENABLED +WEAK const PinMap PinMap_DAC[] = { + {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC1_OUT1 + {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC1_OUT2 + {NC, NP, 0} +}; +#endif + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SDA[] = { + {PA_6, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PA_6_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)}, + {PA_10, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PA_10_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PA_10_R, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PA_10_R_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PA_12, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, + {PB_4, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PB_4_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)}, + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, + {PB_14, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, + {PC_1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SCL[] = { + {PA_7, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PA_7_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)}, + {PA_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PA_9_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PA_9_R, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PA_9_R_ALT1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PA_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, + {PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF8_I2C2)}, + {PB_3_ALT1, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)}, + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C1)}, + {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, + {PB_13, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C2)}, + {PC_0, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF6_I2C3)}, + {NC, NP, 0} +}; +#endif + +//*** TIM *** + +#ifdef HAL_TIM_MODULE_ENABLED +WEAK const PinMap PinMap_TIM[] = { + {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1 + {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2 + {PA_1_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 1)}, // TIM15_CH1N + {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3 + {PA_2_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 0)}, // TIM15_CH1 + {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4 + {PA_3_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 2, 0)}, // TIM15_CH2 + {PA_4, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1 + {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1 + {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1 + {PA_6_ALT1, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM16, 1, 0)}, // TIM16_CH1 + {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N + {PA_7_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2 + {PA_7_ALT2, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM14, 1, 0)}, // TIM14_CH1 + {PA_7_ALT3, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM17, 1, 0)}, // TIM17_CH1 + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 0)}, // TIM1_CH1 + {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2 + {PA_9_R, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2 + {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3 + {PA_10_R, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3 + {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 4, 0)}, // TIM1_CH4 + {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1 + {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N + {PB_0_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3 + {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N + {PB_1_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4 + {PB_1_ALT2, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM14, 1, 0)}, // TIM14_CH1 + {PB_3, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + {PB_3_ALT1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2 + {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1 + {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2 + {PB_6, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + {PB_6_ALT1, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 1, 0)}, // TIM4_CH1 + {PB_6_ALT2, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 1)}, // TIM16_CH1N + {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 2, 0)}, // TIM4_CH2 + {PB_7_ALT1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 1)}, // TIM17_CH1N + {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 3, 0)}, // TIM4_CH3 + {PB_8_ALT1, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 0)}, // TIM16_CH1 + {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM4, 4, 0)}, // TIM4_CH4 + {PB_9_ALT1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 0)}, // TIM17_CH1 + {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3 + {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4 + {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N + {PB_13_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 1)}, // TIM15_CH1N + {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N + {PB_14_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 1, 0)}, // TIM15_CH1 + {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N + {PB_15_ALT1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_TIM15, 1, 1)}, // TIM15_CH1N + {PB_15_ALT2, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_TIM15, 2, 0)}, // TIM15_CH2 + {PC_1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM15, 1, 0)}, // TIM15_CH1 + {PC_2, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM15, 2, 0)}, // TIM15_CH2 + {PC_4, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 1, 0)}, // TIM2_CH1 + {PC_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 2, 0)}, // TIM2_CH2 + {PC_6, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 3, 0)}, // TIM2_CH3 + {PC_6_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1 + {PC_7, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM2, 4, 0)}, // TIM2_CH4 + {PC_7_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2 + {PC_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 0)}, // TIM1_CH1 + {PC_8_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3 + {PC_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 0)}, // TIM1_CH2 + {PC_9_ALT1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4 + {PC_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 0)}, // TIM1_CH3 + {PC_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 4, 0)}, // TIM1_CH4 + {PC_12, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM14, 1, 0)}, // TIM14_CH1 + {PD_0, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM16, 1, 0)}, // TIM16_CH1 + {PD_1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM17, 1, 0)}, // TIM17_CH1 + {PD_2, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 1, 1)}, // TIM1_CH1N + {PD_3, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 2, 1)}, // TIM1_CH2N + {PD_4, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM1, 3, 1)}, // TIM1_CH3N + {PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 + {PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 + {PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3 + {PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 + {PE_0, TIM16, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM16, 1, 0)}, // TIM16_CH1 + {PE_1, TIM17, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM17, 1, 0)}, // TIM17_CH1 + {PE_3, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 1, 0)}, // TIM3_CH1 + {PE_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 2, 0)}, // TIM3_CH2 + {PE_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 3, 0)}, // TIM3_CH3 + {PE_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM3, 4, 0)}, // TIM3_CH4 + {PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + {PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 + {PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + {PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + {PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 + {PF_0, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM14, 1, 0)}, // TIM14_CH1 + {PF_1, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM15, 1, 1)}, // TIM15_CH1N + {PF_12, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 1, 0)}, // TIM15_CH1 + {PF_13, TIM15, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_TIM15, 2, 0)}, // TIM15_CH2 + {NC, NP, 0} +}; +#endif + +//*** UART *** + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_TX[] = { + {PA_0, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)}, + {PA_2, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, + {PA_2_ALT1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_4, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {PA_5, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PA_9_R, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PA_14, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)}, + {PA_14_ALT1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PB_0, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)}, + {PB_2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_3, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PB_6, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)}, + {PB_6_ALT1, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)}, + {PB_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_8_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_11, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PC_0, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)}, + {PC_0_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART6)}, + {PC_1, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PC_4, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PC_4_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PC_6, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)}, + {PC_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PC_10_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART4)}, + {PC_12, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PD_3, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)}, + {PD_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PE_8, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART4)}, + {PE_10, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PF_2, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)}, + {PF_4, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PF_9, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RX[] = { + {PA_1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)}, + {PA_3, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, + {PA_3_ALT1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_5, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PA_10_R, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PA_13, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)}, + {PA_15, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PB_0, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_1, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)}, + {PB_4, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PB_7, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)}, + {PB_7_ALT1, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART1)}, + {PB_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_9_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PB_10, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PB_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PC_0, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PC_1, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)}, + {PC_1_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART6)}, + {PC_5, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PC_5_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PC_7, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)}, + {PC_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PC_11_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART4)}, + {PD_2, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)}, + {PD_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PE_9, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART4)}, + {PE_11, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PF_3, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)}, + {PF_5, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PF_10, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_RTS[] = { + {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PA_15, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_USART3)}, + {PA_15_ALT1, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)}, + {PB_1, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, + {PB_1_ALT1, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)}, + {PB_1_ALT2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_3, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)}, + {PB_5, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)}, + {PB_12, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_14_ALT1, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PC_9, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)}, + {PD_2, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PD_4, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)}, + {PD_4_ALT1, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PD_12, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PD_15, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)}, + {PE_7, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PF_2, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)}, + {PF_3, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {PF_6, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PF_11, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_CTS[] = { + {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART2)}, + {PA_6, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_LPUART1)}, + {PA_6_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PA_6_ALT2, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_USART1)}, + {PB_0, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_LPUART2)}, + {PB_4, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART1)}, + {PB_6, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART5)}, + {PB_7, USART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART4)}, + {PB_13, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PB_13_ALT1, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_USART3)}, + {PB_15, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PC_8, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_LPUART2)}, + {PD_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART2)}, + {PD_5, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PD_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_USART3)}, + {PD_14, LPUART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART2)}, + {PF_7, LPUART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_LPUART1)}, + {PF_7_ALT1, USART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART5)}, + {PF_12, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_USART6)}, + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MOSI[] = { + {PA_2, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PA_4, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PA_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PA_10_R, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PA_12, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_5_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)}, + {PB_7, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PB_11, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI3)}, + {PD_4, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PD_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)}, + {PE_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MISO[] = { + {PA_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PA_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI2)}, + {PA_9_R, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI2)}, + {PA_11, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_4_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)}, + {PB_6, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI2)}, + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI3)}, + {PD_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PD_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)}, + {PE_14, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SCLK[] = { + {PA_0, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PA_1, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_3_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)}, + {PB_8, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF4_SPI3)}, + {PD_1, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PD_8, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)}, + {PE_13, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PA_4_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)}, + {PA_8, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PA_15_ALT1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_SPI3)}, + {PB_0, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI2)}, + {PD_0, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI2)}, + {PD_9, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_SPI1)}, + {PE_12, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF0_SPI1)}, + {NC, NP, 0} +}; +#endif + +//*** FDCAN *** + +#ifdef HAL_FDCAN_MODULE_ENABLED +WEAK const PinMap PinMap_CAN_RD[] = { + {PA_11, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PB_0, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PB_5, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PB_8, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PB_12, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PC_2, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PC_4, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PD_0, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PD_12, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PD_14, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_FDCAN_MODULE_ENABLED +WEAK const PinMap PinMap_CAN_TD[] = { + {PA_12, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PB_1, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PB_6, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PB_9, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PB_13, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PC_3, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {PC_5, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PD_1, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PD_13, FDCAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN1)}, + {PD_15, FDCAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF3_FDCAN2)}, + {NC, NP, 0} +}; +#endif + +//*** No ETHERNET *** + +//*** No QUADSPI *** + +//*** USB *** + +#if defined(HAL_PCD_MODULE_ENABLED) || defined(HAL_HCD_MODULE_ENABLED) +WEAK const PinMap PinMap_USB_DRD_FS[] = { + {PA_4, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_USB)}, // USB_NOE + {PA_11, USB_DRD_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_DM + {PA_12, USB_DRD_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_DP + {PA_13, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_USB)}, // USB_NOE + {PA_15, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USB)}, // USB_NOE + {PC_9, USB_DRD_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_USB)}, // USB_NOE + {NC, NP, 0} +}; +#endif + +//*** No SD *** + +#endif /* !CUSTOM_PERIPHERAL_PINS */ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PinNamesVar.h b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PinNamesVar.h new file mode 100644 index 000000000000..7d35869fe7dd --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/PinNamesVar.h @@ -0,0 +1,91 @@ +/* Remap pin name */ +PA_9_R = PA_9 | PREMAP, +PA_10_R = PA_10 | PREMAP, + +/* Alternate pin name */ +PA_1_ALT1 = PA_1 | ALT1, +PA_2_ALT1 = PA_2 | ALT1, +PA_3_ALT1 = PA_3 | ALT1, +PA_4_ALT1 = PA_4 | ALT1, +PA_6_ALT1 = PA_6 | ALT1, +PA_6_ALT2 = PA_6 | ALT2, +PA_7_ALT1 = PA_7 | ALT1, +PA_7_ALT2 = PA_7 | ALT2, +PA_7_ALT3 = PA_7 | ALT3, +PA_9_ALT1 = PA_9 | ALT1, +PA_9_R_ALT1 = PA_9_R | ALT1, +PA_10_ALT1 = PA_10 | ALT1, +PA_10_R_ALT1 = PA_10_R | ALT1, +PA_14_ALT1 = PA_14 | ALT1, +PA_15_ALT1 = PA_15 | ALT1, +PB_0_ALT1 = PB_0 | ALT1, +PB_1_ALT1 = PB_1 | ALT1, +PB_1_ALT2 = PB_1 | ALT2, +PB_3_ALT1 = PB_3 | ALT1, +PB_4_ALT1 = PB_4 | ALT1, +PB_5_ALT1 = PB_5 | ALT1, +PB_6_ALT1 = PB_6 | ALT1, +PB_6_ALT2 = PB_6 | ALT2, +PB_7_ALT1 = PB_7 | ALT1, +PB_8_ALT1 = PB_8 | ALT1, +PB_9_ALT1 = PB_9 | ALT1, +PB_13_ALT1 = PB_13 | ALT1, +PB_14_ALT1 = PB_14 | ALT1, +PB_15_ALT1 = PB_15 | ALT1, +PB_15_ALT2 = PB_15 | ALT2, +PC_0_ALT1 = PC_0 | ALT1, +PC_1_ALT1 = PC_1 | ALT1, +PC_4_ALT1 = PC_4 | ALT1, +PC_5_ALT1 = PC_5 | ALT1, +PC_6_ALT1 = PC_6 | ALT1, +PC_7_ALT1 = PC_7 | ALT1, +PC_8_ALT1 = PC_8 | ALT1, +PC_9_ALT1 = PC_9 | ALT1, +PC_10_ALT1 = PC_10 | ALT1, +PC_11_ALT1 = PC_11 | ALT1, +PD_4_ALT1 = PD_4 | ALT1, +PF_7_ALT1 = PF_7 | ALT1, + +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 + SYS_WKUP1 = PA_0, +#endif +#ifdef PWR_WAKEUP_PIN2 + SYS_WKUP2 = PC_13, +#endif +#ifdef PWR_WAKEUP_PIN3 + SYS_WKUP3 = PE_6, +#endif +#ifdef PWR_WAKEUP_PIN4 + SYS_WKUP4 = PA_2, +#endif +#ifdef PWR_WAKEUP_PIN5 + SYS_WKUP5 = PC_5, +#endif +#ifdef PWR_WAKEUP_PIN6 + SYS_WKUP6 = PB_5, +#endif +#ifdef PWR_WAKEUP_PIN7 + SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 + SYS_WKUP8 = NC, +#endif + +/* USB */ +#ifdef USBCON + USB_DM = PA_11, + USB_DP = PA_12, + #ifdef USB_NOE_PA_4 + USB_NOE = PA_4, + #endif + #ifdef USB_NOE_PA_13 + USB_NOE = PA_13, + #endif + #ifdef USB_NOE_PA_15 + USB_NOE = PA_15, + #endif + #ifdef USB_NOE_PC_9 + USB_NOE = PC_9, + #endif +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/ldscript.ld new file mode 100644 index 000000000000..db07355fb744 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/ldscript.ld @@ -0,0 +1,177 @@ +/** + ****************************************************************************** + * @file LinkerScript.ld + * @author Auto-generated by STM32CubeIDE + * @brief Linker script for STM32G0B1VETx Device from STM32G0 series + * 512Kbytes FLASH + * 144Kbytes RAM + * + * Set heap size, stack size and stack location according + * to application requirements. + * + * Set memory bank area and size if external memory is used + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2020 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */ + +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Memories definition */ +MEMORY +{ + RAM (xrw) : ORIGIN = 0x20000000, LENGTH = LD_MAX_DATA_SIZE + FLASH (rx) : ORIGIN = 0x8000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET +} + +/* Sections */ +SECTIONS +{ + /* The startup code into "FLASH" Rom type memory */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data into "FLASH" Rom type memory */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data into "FLASH" Rom type memory */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { + . = ALIGN(4); + *(.ARM.extab* .gnu.linkonce.armextab.*) + . = ALIGN(4); + } >FLASH + + .ARM : { + . = ALIGN(4); + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + . = ALIGN(4); + } >FLASH + + .preinit_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + . = ALIGN(4); + } >FLASH + + .init_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + . = ALIGN(4); + } >FLASH + + .fini_array : + { + . = ALIGN(4); + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + . = ALIGN(4); + } >FLASH + + /* Used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections into "RAM" Ram type memory */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + *(.RamFunc) /* .RamFunc sections */ + *(.RamFunc*) /* .RamFunc* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + + } >RAM AT> FLASH + + /* Uninitialized data section into "RAM" Ram type memory */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss section */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + /* Remove information from the compiler libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.cpp b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.cpp new file mode 100644 index 000000000000..8bf88aed49bf --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.cpp @@ -0,0 +1,213 @@ +/* + ******************************************************************************* + * Copyright (c) 2020-2021, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + */ + +#if defined(STM32G0B1xx) +#include "pins_arduino.h" + +// Digital PinName array +const PinName digitalPin[] = { + PA_0, // D0/A0 + PA_1, // D1/A1 + PA_2, // D2/A2 + PA_3, // D3/A3 + PA_4, // D4/A4 + PA_5, // D5/A5 + PA_6, // D6/A6 + PA_7, // D7/A7 + PA_8, // D8 + PA_9, // D9 + PA_10, // D10 + PA_11, // D11 + PA_12, // D12 + PA_13, // D13 + PA_14, // D14 + PA_15, // D15 + PB_0, // D16/A8 + PB_1, // D17/A9 + PB_2, // D18/A10 + PB_3, // D19 + PB_4, // D20 + PB_5, // D21 + PB_6, // D22 + PB_7, // D23 + PB_8, // D24 + PB_9, // D25 + PB_10, // D26/A11 + PB_11, // D27/A12 + PB_12, // D28/A13 + PB_13, // D29 + PB_14, // D30 + PB_15, // D31 + PC_0, // D32 + PC_1, // D33 + PC_2, // D34 + PC_3, // D35 + PC_4, // D36/A14 + PC_5, // D37/A15 + PC_6, // D38 + PC_7, // D39 + PC_8, // D40 + PC_9, // D41 + PC_10, // D42 + PC_11, // D43 + PC_12, // D44 + PC_13, // D45 + PC_14, // D46 + PC_15, // D47 + PD_0, // D48 + PD_1, // D49 + PD_2, // D50 + PD_3, // D51 + PD_4, // D52 + PD_5, // D53 + PD_6, // D54 + PD_7, // D55 + PD_8, // D56 + PD_9, // D57 + PD_10, // D58 + PD_11, // D59 + PD_12, // D60 + PD_13, // D61 + PD_14, // D62 + PD_15, // D63 + PE_0, // D64 + PE_1, // D65 + PE_2, // D66 + PE_3, // D67 + PE_4, // D68 + PE_5, // D69 + PE_6, // D70 + PE_7, // D71 + PE_8, // D72 + PE_9, // D73 + PE_10, // D74 + PE_11, // D75 + PE_12, // D76 + PE_13, // D77 + PE_14, // D78 + PE_15, // D79 + PF_0, // D80 + PF_1, // D81 + PF_2, // D82 + PF_3, // D83 + PF_4, // D84 + PF_5, // D85 + PF_6, // D86 + PF_7, // D87 + PF_8, // D88 + PF_9, // D89 + PF_10, // D90 + PF_11, // D91 + PF_12, // D92 + PF_13, // D93 + PA_9_R, // D94 + PA_10_R // D95 +}; + +// Analog (Ax) pin number array +const uint32_t analogInputPin[] = { + 0, // A0, PA0 + 1, // A1, PA1 + 2, // A2, PA2 + 3, // A3, PA3 + 4, // A4, PA4 + 5, // A5, PA5 + 6, // A6, PA6 + 7, // A7, PA7 + 16, // A8, PB0 + 17, // A9, PB1 + 18, // A10, PB2 + 26, // A11, PB10 + 27, // A12, PB11 + 28, // A13, PB12 + 36, // A14, PC4 + 37 // A15, PC5 +}; + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief System Clock Configuration + * The system Clock is configured as follows : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 64000000 + * HCLK(Hz) = 64000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 1 + * PLL_M = 1 + * PLL_N = 24 + * PLL_R = 3 + * PLL_P = 2 + * PLL_Q = 4 + * USB(Hz) = 48000000 (PLLQ) + * @param None + * @retval None + */ +WEAK void SystemClock_Config(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {0}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; + + // Reset clock registers (in case bootloader has changed them) + SystemInit(); + + /** Configure the main internal regulator output voltage + */ + HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1); + /** Initializes the RCC Oscillators according to the specified parameters + * in the RCC_OscInitTypeDef structure. + */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV1; + RCC_OscInitStruct.PLL.PLLN = 24; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV4; + RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV3; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) + { + Error_Handler(); + } + /** Initializes the CPU, AHB and APB buses clocks + */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK + |RCC_CLOCKTYPE_PCLK1; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) + { + Error_Handler(); + } + /** Initializes the peripherals clocks + */ + PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_PLL; + if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) + { + Error_Handler(); + } +} + +#ifdef __cplusplus +} +#endif +#endif /* STM32G0B1xx */ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.h b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.h new file mode 100644 index 000000000000..e6f2251db059 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1VE/variant_MARLIN_STM32G0B1VE.h @@ -0,0 +1,258 @@ +/* + ******************************************************************************* + * Copyright (c) 2020-2021, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + */ +#pragma once + +/*---------------------------------------------------------------------------- + * STM32 pins number + *----------------------------------------------------------------------------*/ +#define PA0 PIN_A0 +#define PA1 PIN_A1 +#define PA2 PIN_A2 +#define PA3 PIN_A3 +#define PA4 PIN_A4 +#define PA5 PIN_A5 +#define PA6 PIN_A6 +#define PA7 PIN_A7 +#define PA8 8 +#define PA9 9 +#define PA10 10 +#define PA11 11 +#define PA12 12 +#define PA13 13 +#define PA14 14 +#define PA15 15 +#define PB0 PIN_A8 +#define PB1 PIN_A9 +#define PB2 PIN_A10 +#define PB3 19 +#define PB4 20 +#define PB5 21 +#define PB6 22 +#define PB7 23 +#define PB8 24 +#define PB9 25 +#define PB10 PIN_A11 +#define PB11 PIN_A12 +#define PB12 PIN_A13 +#define PB13 29 +#define PB14 30 +#define PB15 31 +#define PC0 32 +#define PC1 33 +#define PC2 34 +#define PC3 35 +#define PC4 PIN_A14 +#define PC5 PIN_A15 +#define PC6 38 +#define PC7 39 +#define PC8 40 +#define PC9 41 +#define PC10 42 +#define PC11 43 +#define PC12 44 +#define PC13 45 +#define PC14 46 +#define PC15 47 +#define PD0 48 +#define PD1 49 +#define PD2 50 +#define PD3 51 +#define PD4 52 +#define PD5 53 +#define PD6 54 +#define PD7 55 +#define PD8 56 +#define PD9 57 +#define PD10 58 +#define PD11 59 +#define PD12 60 +#define PD13 61 +#define PD14 62 +#define PD15 63 +#define PE0 64 +#define PE1 65 +#define PE2 66 +#define PE3 67 +#define PE4 68 +#define PE5 69 +#define PE6 70 +#define PE7 71 +#define PE8 72 +#define PE9 73 +#define PE10 74 +#define PE11 75 +#define PE12 76 +#define PE13 77 +#define PE14 78 +#define PE15 79 +#define PF0 80 +#define PF1 81 +#define PF2 82 +#define PF3 83 +#define PF4 84 +#define PF5 85 +#define PF6 86 +#define PF7 87 +#define PF8 88 +#define PF9 89 +#define PF10 90 +#define PF11 91 +#define PF12 92 +#define PF13 93 +#define PA9_R 94 +#define PA10_R 95 + +// Alternate pins number +#define PA1_ALT1 (PA1 | ALT1) +#define PA2_ALT1 (PA2 | ALT1) +#define PA3_ALT1 (PA3 | ALT1) +#define PA4_ALT1 (PA4 | ALT1) +#define PA6_ALT1 (PA6 | ALT1) +#define PA6_ALT2 (PA6 | ALT2) +#define PA7_ALT1 (PA7 | ALT1) +#define PA7_ALT2 (PA7 | ALT2) +#define PA7_ALT3 (PA7 | ALT3) +#define PA9_ALT1 (PA9 | ALT1) +#define PA9_R_ALT1 (PA9_R | ALT1) +#define PA10_ALT1 (PA10 | ALT1) +#define PA10_R_ALT1 (PA10_R | ALT1) +#define PA14_ALT1 (PA14 | ALT1) +#define PA15_ALT1 (PA15 | ALT1) +#define PB0_ALT1 (PB0 | ALT1) +#define PB1_ALT1 (PB1 | ALT1) +#define PB1_ALT2 (PB1 | ALT2) +#define PB3_ALT1 (PB3 | ALT1) +#define PB4_ALT1 (PB4 | ALT1) +#define PB5_ALT1 (PB5 | ALT1) +#define PB6_ALT1 (PB6 | ALT1) +#define PB6_ALT2 (PB6 | ALT2) +#define PB7_ALT1 (PB7 | ALT1) +#define PB8_ALT1 (PB8 | ALT1) +#define PB9_ALT1 (PB9 | ALT1) +#define PB13_ALT1 (PB13 | ALT1) +#define PB14_ALT1 (PB14 | ALT1) +#define PB15_ALT1 (PB15 | ALT1) +#define PB15_ALT2 (PB15 | ALT2) +#define PC0_ALT1 (PC0 | ALT1) +#define PC1_ALT1 (PC1 | ALT1) +#define PC4_ALT1 (PC4 | ALT1) +#define PC5_ALT1 (PC5 | ALT1) +#define PC6_ALT1 (PC6 | ALT1) +#define PC7_ALT1 (PC7 | ALT1) +#define PC8_ALT1 (PC8 | ALT1) +#define PC9_ALT1 (PC9 | ALT1) +#define PC10_ALT1 (PC10 | ALT1) +#define PC11_ALT1 (PC11 | ALT1) +#define PD4_ALT1 (PD4 | ALT1) +#define PF7_ALT1 (PF7 | ALT1) + +#define NUM_DIGITAL_PINS 96 +#define NUM_REMAP_PINS 2 +#define NUM_ANALOG_INPUTS 16 + +// On-board LED pin number +#ifndef LED_BUILTIN + #define LED_BUILTIN PNUM_NOT_DEFINED +#endif + +// On-board user button +#ifndef USER_BTN + #define USER_BTN PNUM_NOT_DEFINED +#endif + +// SPI definitions +#ifndef PIN_SPI_SS + #define PIN_SPI_SS PA4 +#endif +#ifndef PIN_SPI_SS1 + #define PIN_SPI_SS1 PA15 +#endif +#ifndef PIN_SPI_SS2 + #define PIN_SPI_SS2 PB0 +#endif +#ifndef PIN_SPI_SS3 + #define PIN_SPI_SS3 PD9 +#endif +#ifndef PIN_SPI_MOSI + #define PIN_SPI_MOSI PA2 +#endif +#ifndef PIN_SPI_MISO + #define PIN_SPI_MISO PA6 +#endif +#ifndef PIN_SPI_SCK + #define PIN_SPI_SCK PA1 +#endif + +// I2C definitions +#ifndef PIN_WIRE_SDA + #define PIN_WIRE_SDA PA6 +#endif +#ifndef PIN_WIRE_SCL + #define PIN_WIRE_SCL PA7 +#endif + +// Timer Definitions +// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin +#ifndef TIMER_TONE + #define TIMER_TONE TIM6 +#endif +#ifndef TIMER_SERVO + #define TIMER_SERVO TIM7 +#endif + +// UART Definitions +#ifndef SERIAL_UART_INSTANCE + #define SERIAL_UART_INSTANCE 4 +#endif + +// Default pin used for generic 'Serial' instance +// Mandatory for Firmata +#ifndef PIN_SERIAL_RX + #define PIN_SERIAL_RX PA1 +#endif +#ifndef PIN_SERIAL_TX + #define PIN_SERIAL_TX PA0 +#endif + +// Extra HAL modules +#if !defined(HAL_DAC_MODULE_DISABLED) + #define HAL_DAC_MODULE_ENABLED +#endif + +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus + // These serial port names are intended to allow libraries and architecture-neutral + // sketches to automatically default to the correct port name for a particular type + // of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, + // the first hardware serial port whose RX/TX pins are not dedicated to another use. + // + // SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor + // + // SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial + // + // SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library + // + // SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. + // + // SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX + // pins are NOT connected to anything by default. + #ifndef SERIAL_PORT_MONITOR + #define SERIAL_PORT_MONITOR Serial + #endif + #ifndef SERIAL_PORT_HARDWARE + #define SERIAL_PORT_HARDWARE Serial + #endif +#endif diff --git a/ini/stm32g0.ini b/ini/stm32g0.ini index 568d9c8e9f01..c8554741bceb 100644 --- a/ini/stm32g0.ini +++ b/ini/stm32g0.ini @@ -41,7 +41,7 @@ upload_protocol = stlink debug_tool = stlink # -# BigTreeTech SKR mini E3 V3.0 (STM32G0B1RET6 ARM Cortex-M0+) +# BigTreeTech SKR Mini E3 V3.0 / Manta E3 EZ V1.0 / Manta M4P V1.0 / Manta M5P V1.0 (STM32G0B1RET6 ARM Cortex-M0+) # [env:STM32G0B1RE_btt] extends = stm32_variant @@ -59,6 +59,7 @@ upload_protocol = stlink debug_tool = stlink # +# BigTreeTech SKR Mini E3 V3.0 / Manta E3 EZ V1.0 / Manta M4P V1.0 / Manta M5P V1.0 (STM32G0B1RET6 ARM Cortex-M0+) # Custom upload to SD via Marlin with Binary Protocol # [env:STM32G0B1RE_btt_xfer] @@ -67,3 +68,33 @@ build_flags = ${env:STM32G0B1RE_btt.build_flags} -DXFER_BUILD extra_scripts = ${env:STM32G0B1RE_btt.extra_scripts} pre:buildroot/share/scripts/upload.py upload_protocol = custom + +# +# BigTreeTech Manta M8P V1.x (STM32G0B1VET6 ARM Cortex-M0+) +# +[env:STM32G0B1VE_btt] +extends = stm32_variant +platform = ststm32@~14.1.0 +platform_packages = framework-arduinoststm32@https://github.com/stm32duino/Arduino_Core_STM32/archive/main.zip +board = marlin_STM32G0B1VE +board_build.offset = 0x2000 +board_upload.offset_address = 0x08002000 +build_flags = ${stm32_variant.build_flags} + -DPIN_SERIAL4_RX=PE_9 -DPIN_SERIAL4_TX=PE_8 + -DPIN_SERIAL5_RX=PE_11 -DPIN_SERIAL5_TX=PE_10 + -DSERIAL_RX_BUFFER_SIZE=1024 -DSERIAL_TX_BUFFER_SIZE=1024 + -DTIMER_SERVO=TIM3 -DTIMER_TONE=TIM4 + -DSTEP_TIMER_IRQ_PRIO=0 +upload_protocol = stlink +debug_tool = stlink + +# +# BigTreeTech Manta M8P V1.x (STM32G0B1VET6 ARM Cortex-M0+) +# Custom upload to SD via Marlin with Binary Protocol +# +[env:STM32G0B1VE_btt_xfer] +extends = env:STM32G0B1VE_btt +build_flags = ${env:STM32G0B1VE_btt.build_flags} -DXFER_BUILD +extra_scripts = ${env:STM32G0B1VE_btt.extra_scripts} + pre:buildroot/share/scripts/upload.py +upload_protocol = custom