Skip to content

ainsuForth - generalized - all targets, including SAMD51 M4 - experimental

License

Notifications You must be signed in to change notification settings

wa1tnr/ainsuForth-gen-exp-m4

Repository files navigation

ainsuForth-gen-exp-m4

ainsuForth - generalized - all targets including SAMD51 M4 - experimental

+NeoTrellis M4 - SAMD51G19A +Metro M4 Express - SAMD51J19A +ItsyBitsy M4 Express - SAMD51G19A +Feather M4 Express - SAMD51J19A

(previously ainsuForth-gen-exp)

gen-exp means generalized and experimental; generalized to all the available target boards (trying to move as much of that into compatibility.h as a single-source place to look for porting issues, across targets).

This forth is compiled regularly (as targets are reused to test other code). It is usually operational. ;)

31 Aug 2023

Quick check on NeoTrellis M4 - was able to recreate the load file after a remove.

Main purpose of checking the program in August of 2023 to make sure it still compiles - it does.

No obvious operational impairment noticed.

eflmkdir is 'rigged' to disallow command line use - just alias it in a colon definition to use it.

20 Feb 2021:

Please see branch update-2021-aa

Tested against ItsyBitsyM4 - works okay. Reads and writes to QSPI flashROM.

signon msg is:

Hello from setup_qspi m4 getline stuff. Found QSPI Flash. NOV 2018: Mounted filesystem!

warm boot message - early bird. c: 15e708efc75 teg-SIWNA +SPIFl2k19 +trm4x +fm4x +crickitCPX c6a DEVPR - gen-exp-m4 20 Feb 2021 type 'warm' to reboot Sat Feb 20 09:54:27 2021 update-2021-aa xxxx-a3c-00k- ItsyBitsy M4 Express sand birds

 ainsuForth - 2018 - wa1tnr    words: 86
     YAFFA - Yet Another Forth For Arduino,
     Copyright (C) 2012 Stuart Wood

ok

New 05 Aug 2019:

On branch develop / testing-gg- / master

The code should be ready for a release, against the older QSPI flashROM lib (October 2018 timeframe).

Code is broken for latest (2019) Adafruit libs (wrt the QSPI flashROM support) and will be addressed some other time.

Roll back your libs to an earlier version, to compile. ;)

Adafruit_QSPI
Adafruit_SPIFlash

Both may be affected. Have not documented just what to do with this, though a good test compile was done in early August, 2019, by rolling back one or both of these (and possibly others; this is off-the-cuff reportage ;)

The program (as-is, and against Oct 2018 Adafruit libs) will accept code in the forth interpreter, and write it to the flashROM (to a single named file).

It will also 'play back' the same code, as if a human had typed it to the regular forth interpreter.

In this way, code may be developed on the device itself, and stored for future use. ;)

The user interface is identical to the one used when developed for SAMD21. The (recent) change is about supporting similar functionality for the M4 (SAMD51) chip series (Feather M4 Express, ItsyBitsyM4, Trellis M4).

Grand Central was not looked into, at the time of this writing (August 2019).

Hopefully the release actually works; it's untested but believed to have been previously tested (so this is mostly a human memory problem, more than an actual, executable code problem .. that's the working assumption!)

Mon Aug 5 01:05:34 UTC 2019

New 12 Nov 2018:

On branch _with_file_io_aa-

QSPI flashROM support (basic file i/o) for Metro M4 Express.

Older commentary on flashROM support follows:

SPI flashROM

flashROM support is limited to the JEDEC stuff for samd21 (SPI rather than QSPI). It occurs in the form of an ability to capture text to disk and replay that text to program the forth compiler/interpreter.

It works well enough to be useful on a dumb serial terminal (with USB interface). Tested during a power outage when the usual resources weren't available. Still primitive, but a useful asset.

No effort was made at file management, so it's just the one file on SPI flashROM at present (which can be reset to zero length, from inside the forth interpreter).

22 August 2018:

Development for a bare-metal Forth in

https://github.com/wa1tnr/ainsuMtxd21.git (samd21)

The most recent branch incorporating what is achieved is found

On branch KM_converser_aa-

of that repository.

Earlier work was done on samd51 (clocks look good; bidirectional USART looks good):

https://github.com/wa1tnr/samd51_USART_basic.git (samd51)

The most recent (non-clock) work was carried over (back to) samd51 in the ainsuMtxd21 repo, currently branch KM_converser_aa- (just menttioned).

There is also a UART-based version of ainsuForth-gen-exp-m4, (written in Arduino IDE c++ code) though it hasn't been published.

All that was required was a global search and replace for 'Serial.' with 'Serial1.' to get that to work quite well (using CP2104 USART-USB bridge chip; reference implementation was for Adafruit PiUART - a nice way to leverage this, quickly, with just two wires (plus ground, for three wires, total).

12 June 2018: Nothing said below this line is reliable, as it is a copy-over from an earlier project and hasn't been looked at, recently. Ignore (or interpret from past events).

August 2018 update: Haven't removed what's below, nor reviewed it.

It's so much easier to just be diligent with 'git diff' and to use 'gitk' to step through the changes (though that is the developer's point of view; for the end-user, hard to say).


Suggest: diff against ainsuForth-gen-exp -- which was the best SAMD21 M0 effort, to date.

Older notes follow. No effort is made to update them, or remove where no longer applicable.

August 2nd:

More experimental -- looking at adding SPI flash write support, file capture from ASCII upload (the 'download' word) and perhaps splitting out file i/o to its own proper source files.

EXPERIMENTAL -- the below, plus a limited use of the SPI flash to author forth source code on the device. Currently, this amounts to reading a full program (a multi-line forth source program) from /forth/job.fs on the SPI flash volume.

Platform: Circuit Playground Express (an M0 board w/SPI 2MB flashROM) - 02 Aug 2017

A Forth for SAMD21G18A based on YAFFA-ARM Forth - 2012 by Stuart Wood.

See compatibility.h for (some) configuration options across target board devices (subset of boards.txt found under

.arduino15/packages/adafruit/hardware/samd/1.0.18/boards.txt )


Current platform is the

Adafruit Metro M4 Express Beta -- 13 May 2018.

was:

Adafruit Feather M0 Express -- 15 January 2018.

All other platform declarations are incorrect, where they differ from this one.


OLD: Current platform is the Adafruit CPX (Circuit Playground Express) - PRODUCT ID: 3333 which is ATSAMD21 Cortex M0+ based.

Platform will change frequently -- seven different targets are tested on a (somewhat) rotating basis:

  • Adafruit Metro M4 Express Beta (SAMD51)
  • Arduino M0 Pro (SAMD21)
  • Adafruit Feather M0 Express
  • Adafruit Metro M0 Express
  • Adafruit Circuit Playground Express
  • Adafruit Gemma M0
  • Adafruit Trinket M0

Sun 13 May 00:34:29 UTC 2018

28f54e6bc7

old:

YAFFA-ARM

YAFFA for Arduino ARM Processors

See: [ https://github.com/sdwood68/YAFFA-ARM ]

About

ainsuForth - generalized - all targets, including SAMD51 M4 - experimental

Topics

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages