printer-20230424_225319.cfg

# This file contains pin mappings for the Creality Ender 5 Plus with a BTT Octopus Pro.

# See docs/Config_Reference.md for a description of parameters.

[include mainsail.cfg]
[include macros.cfg]
[include Adaptive_Mesh.cfg]
[include Line_Purge.cfg]
[include tmc2209.cfg]
[include fans.cfg]

[stepper_x]
step_pin: PF13
dir_pin: !PF12
enable_pin: !PF14
microsteps: 16
rotation_distance: 40
endstop_pin: ^PG6
position_endstop: 347
position_max: 347
homing_speed: 80

[stepper_y]
step_pin: PG0
dir_pin: !PG1
enable_pin: !PF15
microsteps: 16
rotation_distance: 40
endstop_pin: ^PG9
position_endstop: 365
position_max: 365
homing_speed: 80

[stepper_z]
step_pin: PF11
dir_pin: !PG3
enable_pin: !PG5
microsteps: 16
rotation_distance: 4
endstop_pin: probe:z_virtual_endstop
position_max: 400
position_min: -5
homing_speed: 10.0

[extruder]
step_pin: PF9
dir_pin: !PF10
enable_pin: !PG2
microsteps: 16
rotation_distance: 23.578
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PF3
#control: pid
#pid_Kp: 22.2
#pid_Ki: 1.08
#pid_Kd: 114
min_temp: -273.15
max_temp: 600
max_extrude_cross_section: 5

[safe_z_home]
home_xy_position: 225, 180
speed: 100
z_hop: 10
z_hop_speed: 5

[bltouch]
sensor_pin: ^PB7
control_pin: PB6
x_offset: -55
y_offset: -17
#z_offset: 2.45
speed: 3.0
pin_up_touch_mode_reports_triggered: False

[bed_mesh]
speed: 200
horizontal_move_z: 5
mesh_min: 5, 22
mesh_max: 290, 345
probe_count: 7,7
algorithm: bicubic

[heater_bed]
heater_pin: PB11 #HE3
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PF7
control: pid
pid_Kp: 690.34
pid_Ki: 111.47
pid_Kd: 1068.83
min_temp: -273.15
max_temp: 600

[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_26002900105053424E363620-if00

[filament_switch_sensor filament_sensor]
switch_pin:PE4

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2500
max_z_velocity: 5
max_z_accel: 100

[force_move]
enable_force_move: true
#   Set to true to enable FORCE_MOVE and SET_KINEMATIC_POSITION
#   extended G-Code commands. The default is false.

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	0.001250, 0.060000, -0.195000
#*# 	0.086250, 0.181250, -0.043750
#*# 	-0.055000, 0.077500, -0.031250
#*# tension = 0.2
#*# min_x = 5.0
#*# algo = lagrange
#*# y_count = 3
#*# mesh_y_pps = 2
#*# min_y = 22.0
#*# x_count = 3
#*# max_y = 345.0
#*# mesh_x_pps = 2
#*# max_x = 290.0
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 30.429
#*# pid_ki = 2.070
#*# pid_kd = 111.828
#*#
#*# [bltouch]
#*# z_offset = 3.000