Missing define BLTOUCH_V3

[DarkAlchy]

I have people telling me to uncomment that line in configuration_adv.h but in last week's commit or today's commit there is no sign of this in V2 bugfix. Any ideas?

[thisiskeithb]

They are using bugfix-1.1.x or haven't updated their configs in a while.

Edit: It was removed May 7: #13814

[Ludy87]

Marlin/Marlin/src/inc/SanityCheck.h

Line 214 in c1b99c4

#elif defined(BLTOUCH_V3)

BLTOUCH_V3 is obsolete. Please update your configuration.

[Ludy87]

Marlin/Marlin/Configuration.h

Line 853 in c1b99c4

//#define BLTOUCH

Marlin/Marlin/Configuration_adv.h

Lines 530 to 595 in c1b99c4

	#if ENABLED(BLTOUCH)
	/**
	* Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
	* Do not activate settings that the probe might not understand. Clones might misunderstand
	* advanced commands.
	*
	* Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
	* check the wiring of the BROWN, RED and ORANGE wires.
	*
	* Note: If the trigger signal of your probe is not being recognized, it has been very often
	* because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
	* like they would be with a real switch. So please check the wiring first.
	*
	* Settings for all BLTouch and clone probes:
	*/
	// Safety: The probe needs time to recognize the command.
	// Minimum command delay (ms). Enable and increase if needed.
	//#define BLTOUCH_DELAY 500
	/**
	* Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
	*/
	// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
	// in special cases, like noisy or filtered input configurations.
	//#define BLTOUCH_FORCE_SW_MODE
	/**
	* Settings for BLTouch Smart 3.0 and 3.1
	* Summary:
	* - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
	* - High-Speed mode
	* - Disable LCD voltage options
	*/
	/**
	* Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
	* V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
	* If disabled, OD mode is the hard-coded default on 3.0
	* On startup, Marlin will compare its eeprom to this vale. If the selected mode
	* differs, a mode set eeprom write will be completed at initialization.
	* Use the option below to force an eeprom write to a V3.1 probe regardless.
	*/
	//#define BLTOUCH_SET_5V_MODE
	/**
	* Safety: Activate if connecting a probe with an unknown voltage mode.
	* V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
	* V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
	* To preserve the life of the probe, use this once then turn it off and re-flash.
	*/
	//#define BLTOUCH_FORCE_MODE_SET
	/**
	* Use "HIGH SPEED" mode for probing.
	* Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
	* This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
	* If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
	*/
	//#define BLTOUCH_HS_MODE
	// Safety: Enable voltage mode settings in the LCD menu.
	//#define BLTOUCH_LCD_VOLTAGE_MENU
	#endif // BLTOUCH

[DarkAlchy]

Thank you everyone.

[github-actions]

This issue has been automatically locked since there has not been any recent activity after it was closed. Please open a new issue for related bugs.