Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Jump to bottom

No filesystem could mount root on Escam PVR008 #40

Closed
001Tycoon opened this issue Aug 22, 2021 · 13 comments
Closed

No filesystem could mount root on Escam PVR008 #40

001Tycoon opened this issue Aug 22, 2021 · 13 comments

Comments

@001Tycoon
Copy link

Hello
Model Escam PVR008
Board S834-A0-B
Sensor F23
CPU Hi3518ERNCV300
Network Realtk 8188ETV (M8188FU3)

openipc-2.1 commit ab38bfa
serial flash
u-boot 0x000000 Length 0x100000
uImage 0x100000 Length 0x200000
rootfs.squashfs 0x300000 Length 0x500000

bootargs=mem=${osmem:-32M} console=ttyAMA0,115200 panic=5 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data)
bootcmd=setenv setargs setenv bootargs ${bootargs}; run setargs; sf probe 0; sf read 0x42000000 0x100000 0x300000; bootm 0x42000000

System startup

Uncompress Ok!

U-Boot 2020.01 (Sep 02 2020 - 17:34:02 +0800)hi3518ev300

DRAM: SPI Nor: hifmc_ip_ver_check(54): Check Flash Memory Controller v100 ...hifmc_ip_ver_check(60): Found
hifmc_spi_nor_probe(2070): SPI Nor ID Table Version 1.0
hifmc_spi_nor_probe(2095): SPI Nor(cs 0) ID: 0x20 0x70 0x18
hifmc_init_print(2016): Block:64KB hifmc_init_print(2017): Chip:16MB hifmc_init_print(2018): Name:"XM25QH128A"
hifmc100_spi_nor_probe(145): SPI Nor total size: 16MB
NAND: 0 MiB
Loading Environment from SPI Flash... OK
In: serial
Out: serial
Err: serial
Net: eth0
Error: eth0 address not set.

Hit any key to stop autoboot: 0
device 0 offset 0x100000, size 0x300000

SF: 3145728 bytes @ 0x100000 Read: OK
Booting kernel from Legacy Image at 42000000 ...
Image Name: Linux-4.9.37
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1978216 Bytes = 1.9 MiB
Load Address: 40008000
Entry Point: 40008000
Loading Kernel Image

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 4.9.37 (ingo@acer-p256-m) (gcc version 7.5.0 (Buildroot -gab38bfa) ) #1 Sun Aug 22 09:27:48 CEST 2021
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt:Machine model: Hisilicon HI3518EV300 DEMO Board
cmz zone is not set!
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: mem=32M console=ttyAMA0,115200 panic=5 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data)
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26776K/32768K available (4084K kernel code, 148K rwdata, 912K rodata, 176K init, 243K bss, 5992K reserved, 0K cma-reserved)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc2800000 - 0xff800000 ( 976 MB)
lowmem : 0xc0000000 - 0xc2000000 ( 32 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0405538 (4086 kB)
.init : 0xc04ec000 - 0xc0518000 ( 176 kB)
.data : 0xc0518000 - 0xc053d360 ( 149 kB)
.bss : 0xc053f000 - 0xc057bcc8 ( 244 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:16 nr_irqs:16 16
Gic dist init...
arm_arch_timer: Architected cp15 timer(s) running at 50.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
Switching to timer-based delay loop, resolution 20ns
clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x40008200 - 0x40008258
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Serial: AMBA PL011 UART driver
12040000.uart: ttyAMA0 at MMIO 0x12040000 (irq = 20, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
ssp-pl022 12070000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12070000.spi: mapped registers from 0x12070000 to c2867000
ssp-pl022 12071000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12071000.spi: mapped registers from 0x12071000 to c286b000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
workingset: timestamp_bits=30 max_order=13 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pl061_gpio 120b0000.gpio_chip: PL061 GPIO chip @0x120b0000 registered
pl061_gpio 120b1000.gpio_chip: PL061 GPIO chip @0x120b1000 registered
pl061_gpio 120b2000.gpio_chip: PL061 GPIO chip @0x120b2000 registered
pl061_gpio 120b4000.gpio_chip: PL061 GPIO chip @0x120b4000 registered
pl061_gpio 120b5000.gpio_chip: PL061 GPIO chip @0x120b5000 registered
pl061_gpio 120b6000.gpio_chip: PL061 GPIO chip @0x120b6000 registered
pl061_gpio 120b7000.gpio_chip: PL061 GPIO chip @0x120b7000 registered
pl061_gpio 120b8000.gpio_chip: PL061 GPIO chip @0x120b8000 registered
brd: module loaded
hisi-sfc hisi_spi_nor.0: SPI Nor ID Table Version 1.2
hisi-sfc hisi_spi_nor.0: The ID: 0x20 isn't in the BP table, Current device can't not protect
@spi_nor_scan(), no "m25p,fast-read".
@spi_nor_scan(), modes->rd_modes:0x3d.
hisi-sfc hisi_spi_nor.0: (Fast) Read: opcode=EBh, protocol=144, mode=0, wait=24
hisi-sfc hisi_spi_nor.0: nor->read_opcode[3: Read; 0B: Fast Read; 3B: Dual; BB: Dual IO; 6B: Quad; EB: Quad IO]: 0xeb.
hisi-sfc hisi_spi_nor.0: xm25qh128a (Chipsize 16 Mbytes, Blocksize 64KiB)
5 cmdlinepart partitions found on MTD device hi_sfc
5 cmdlinepart partitions found on MTD device hi_sfc
Creating 5 MTD partitions on "hi_sfc":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000050000 : "env"
0x000000050000-0x000000250000 : "kernel"
0x000000250000-0x000000750000 : "rootfs"
0x000000750000-0x000001000000 : "rootfs_data"
SPI Nand ID Table Version 2.7
Cannot found a valid SPI Nand Device
hisi_spi_nand_probe(175): Error: driver probe, result: -19
No OTP data, festa PHY use default ATE parameters!
festa PHY wait autotrim done timeout!
libphy: hisi_femac_mii_bus: probed
libphy: Fixed MDIO Bus: probed
hisi-femac 10040000.ethernet: connect to PHY failed!
hibvt_rtc 120e0000.rtc: rtc core: registered 120e0000.rtc as rtc0
hibvt_rtc 120e0000.rtc: RTC driver for hibvt enabled
i2c /dev entries driver
hibvt-i2c 12060000.i2c: hibvt-i2c0@100000hz registered
hibvt-i2c 12061000.i2c: hibvt-i2c1@100000hz registered
hibvt-i2c 12062000.i2c: hibvt-i2c2@100000hz registered
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on 10010000.sdhci [10010000.sdhci] using ADMA in legacy mode
mmc1: SDHCI controller on 10020000.sdhci [10020000.sdhci] using ADMA in legacy mode
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Key type dns_resolver registered
hibvt_rtc 120e0000.rtc: hctosys: unable to read the hardware clock
List of all partitions:
0100 65536 ram0 (driver?)
0101 65536 ram1 (driver?)
0102 65536 ram2 (driver?)
0103 65536 ram3 (driver?)
0104 65536 ram4 (driver?)
0105 65536 ram5 (driver?)
0106 65536 ram6 (driver?)
0107 65536 ram7 (driver?)
0108 65536 ram8 (driver?)
0109 65536 ram9 (driver?)
010a 65536 ram10 (driver?)
010b 65536 ram11 (driver?)
010c 65536 ram12 (driver?)
010d 65536 ram13 (driver?)
010e 65536 ram14 (driver?)
010f 65536 ram15 (driver?)
1f00 256 mtdblock0 (driver?)
1f01 64 mtdblock1 (driver?)
1f02 2048 mtdblock2 (driver?)
1f03 5120 mtdblock3 (driver?)
1f04 8896 mtdblock4 (driver?)
No filesystem could mount root, tried: squashfs

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
CPU: 0 PID: 1 Comm: swapper Not tainted 4.9.37 #1
Hardware name: Generic DT based system
Backtrace:
[] (dump_backtrace) from [] (show_stack+0x18/0x1c)
r7:c1a6d009 r6:c047de88 r5:00000000 r4:c053f2e8
[] (show_stack) from [] (dump_stack+0x24/0x28)
[] (dump_stack) from [] (panic+0xe4/0x24c)
[] (panic) from [] (mount_block_root+0x280/0x2dc)
r3:d3053b52 r2:d3053b52 r1:c183de8c r0:c047de88
r7:c1a6d009
[] (mount_block_root) from [] (mount_root+0x138/0x154)
r10:c050d838 r9:c04ec620 r8:c050d834 r7:c053f024 r6:c051d18c r5:01f00003
r4:c051a808
[] (mount_root) from [] (prepare_namespace+0x184/0x1cc)
r10:c050d838 r9:c04ec620 r8:c050d834 r7:c053f000 r6:c053f000 r5:c053f024
r4:c050d858
[] (prepare_namespace) from [] (kernel_init_freeable+0x1d0/0x1e0)
r6:c053f000 r5:00000009 r4:c04e93a4
[] (kernel_init_freeable) from [] (kernel_init+0x10/0xfc)
r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0400448
r4:00000000
[] (kernel_init) from [] (ret_from_fork+0x14/0x2c)
r5:c0400448 r4:00000000

hisilicon # bdinfo
arch_number = 0x00001f40
boot_params = 0x40000100
DRAM bank = 0x00000000
-> start = 0x40000000
-> size = 0x04000000
eth0name = eth0
ethaddr = (not set)
current eth = eth0
ip_addr = 192.168.2.221
baudrate = 115200 bps
TLB addr = 0x43ff0000
relocaddr = 0x43f68000
reloc off = 0x03768000
irq_sp = 0x43ec7ed0
sp start = 0x43ec7ec0
Early malloc usage: 6c / 2000
hisilicon # coninfo
List of available devices:
serial 00000003 IO stdin stdout stderr
pl01x_serial 00000003 IO

hisilicon # getinfo spi
Block:64KB Chip:16MB*1
ID:0x20 0x70 0x18
Name:"XM25QH128A"

hisilicon # pri
arch=arm
baudrate=115200
board=hi3518ev300
board_id=MHgyMDdm
board_name=hi3518ev300
bootargs=mem=${osmem:-32M} console=ttyAMA0,115200 panic=5 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data)
bootcmd=setenv setargs setenv bootargs ${bootargs}; run setargs; sf probe 0; sf read 0x42000000 0x100000 0x300000; bootm 0x42000000
bootdelay=1
cpu=armv7
ethact=eth0
ipaddr=192.168.2.221
netmask=255.255.255.0
osmem=32M
ptzsupport=1
sensor_name=F23
serverip=192.168.2.40
soc=hi3518ev300
stderr=serial
stdin=serial
stdout=serial
totalmem=64M
vendor=hisilicon
verify=n

Environment size: 889/262140 bytes

what can I do that he finds the root filesystem
@ZigFisher
Copy link
Collaborator

Good afternoon
Your type of flash drive is not supported in the current version of Linux in the openipc-2.1 project.
Please send a photo of the flash chip (8 pin) or a text description.

@dimerr
Copy link
Collaborator

dimerr commented Aug 24, 2021

Try with the latest commit/build

@001Tycoon
Copy link
Author

Hello
@dimerr Try with the latest commit/build Patch error

patching file scripts/Makefile.clean
patching file scripts/setlocalversion
patching file scripts/dtc/dtc-lexer.lex.c_shipped
patching file drivers/mtd/spi-nor/spi-nor.c
patching file drivers/mtd/spi-nor/spi-nor.c
patching file drivers/mtd/spi-nor/spi-nor.c
patching file drivers/mtd/spi-nor/spi-nor.c
patch unexpectedly ends in middle of line
Hunk #1 succeeded at 1219 with fuzz 2.
can't find file to patch at input line 3
Perhaps you used the wrong -p or --strip option?
The text leading up to this was:
--------------------------
|--- a/drivers/mtd/spi-nor/spi-nor.c<--->2021-08-24 08:00:01.771026933 +0300
|+++ b/drivers/mtd/spi-nor/spi-nor.c<--->2021-08-24 08:04:33.973630596 +0300
--------------------------
File to patch:

@ZigFisher
IMG_20210824_080130

With other settings it is boot up

bootargs=mem=${osmem} console=ttyAMA0,115200 panic=5 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=hi_sfc:960k(boot),64k(env),2048k(kernel),6144k(rootfs),-(rootfs_data)
bootcmd=setenv setargs setenv bootargs ${bootargs}; run setargs; sf probe 0; sf read 0x41000000 0x100000 0x200000; bootm 0x41000000

SF: 2097152 bytes @ 0x100000 Read: OK
## Booting kernel from Legacy Image at 41000000 ...
   Image Name:   Linux-4.9.37
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1980080 Bytes = 1.9 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Loading Kernel Image

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 4.9.37 (ingo@acer-p256-m) (gcc version 7.5.0 (Buildroot -gcc7fac4-dirty) ) #1 Mon Aug 23 22:56:57 CEST 2021
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt:Machine model: Hisilicon HI3518EV300 DEMO Board
cmz zone is not set!
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: mem=32M console=ttyAMA0,115200 panic=5 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=hi_sfc:960k(boot),64k(env),2048k(kernel),6144k(rootfs),-(rootfs_data)
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26772K/32768K available (4085K kernel code, 149K rwdata, 916K rodata, 172K init, 243K bss, 5996K reserved, 0K cma-reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xc2800000 - 0xff800000   ( 976 MB)
    lowmem  : 0xc0000000 - 0xc2000000   (  32 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc04056d8   (4086 kB)
      .init : 0xc04ed000 - 0xc0518000   ( 172 kB)
      .data : 0xc0518000 - 0xc053d760   ( 150 kB)
       .bss : 0xc053f000 - 0xc057bcc8   ( 244 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:16 nr_irqs:16 16
Gic dist init...
arm_arch_timer: Architected cp15 timer(s) running at 50.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
Switching to timer-based delay loop, resolution 20ns
clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x40008200 - 0x40008258
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Serial: AMBA PL011 UART driver
12040000.uart: ttyAMA0 at MMIO 0x12040000 (irq = 20, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
ssp-pl022 12070000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12070000.spi: mapped registers from 0x12070000 to c2867000
ssp-pl022 12071000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12071000.spi: mapped registers from 0x12071000 to c286b000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
workingset: timestamp_bits=30 max_order=13 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pl061_gpio 120b0000.gpio_chip: PL061 GPIO chip @0x120b0000 registered
pl061_gpio 120b1000.gpio_chip: PL061 GPIO chip @0x120b1000 registered
pl061_gpio 120b2000.gpio_chip: PL061 GPIO chip @0x120b2000 registered
pl061_gpio 120b4000.gpio_chip: PL061 GPIO chip @0x120b4000 registered
pl061_gpio 120b5000.gpio_chip: PL061 GPIO chip @0x120b5000 registered
pl061_gpio 120b6000.gpio_chip: PL061 GPIO chip @0x120b6000 registered
pl061_gpio 120b7000.gpio_chip: PL061 GPIO chip @0x120b7000 registered
pl061_gpio 120b8000.gpio_chip: PL061 GPIO chip @0x120b8000 registered
brd: module loaded
hisi-sfc hisi_spi_nor.0: SPI Nor ID Table Version 1.2
hisi-sfc hisi_spi_nor.0: The ID: 0x20 isn't in the BP table, Current device can't not protect
@spi_nor_scan(), no "m25p,fast-read".
@spi_nor_scan(), modes->rd_modes:0x3d.
hisi-sfc hisi_spi_nor.0: (Fast) Read:  opcode=EBh, protocol=144, mode=0, wait=24
hisi-sfc hisi_spi_nor.0: nor->read_opcode[3: Read; 0B: Fast Read; 3B: Dual; BB: Dual IO; 6B: Quad; EB: Quad IO]: 0xeb.
hisi-sfc hisi_spi_nor.0: xm25qh128a (Chipsize 16 Mbytes, Blocksize 64KiB)
5 cmdlinepart partitions found on MTD device hi_sfc
5 cmdlinepart partitions found on MTD device hi_sfc
Creating 5 MTD partitions on "hi_sfc":
0x000000000000-0x0000000f0000 : "boot"
0x0000000f0000-0x000000100000 : "env"
0x000000100000-0x000000300000 : "kernel"
0x000000300000-0x000000900000 : "rootfs"
0x000000900000-0x000001000000 : "rootfs_data"
SPI Nand ID Table Version 2.7
Cannot found a valid SPI Nand Device
hisi_spi_nand_probe(175): Error: driver probe, result: -19
No OTP data, festa PHY use default ATE parameters!
festa PHY wait autotrim done timeout!
libphy: hisi_femac_mii_bus: probed
libphy: Fixed MDIO Bus: probed
hisi-femac 10040000.ethernet: connect to PHY failed!
hibvt_rtc 120e0000.rtc: rtc core: registered 120e0000.rtc as rtc0
hibvt_rtc 120e0000.rtc: RTC driver for hibvt enabled
i2c /dev entries driver
hibvt-i2c 12060000.i2c: hibvt-i2c0@100000hz registered
hibvt-i2c 12061000.i2c: hibvt-i2c1@100000hz registered
hibvt-i2c 12062000.i2c: hibvt-i2c2@100000hz registered
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on 10010000.sdhci [10010000.sdhci] using ADMA in legacy mode
mmc1: SDHCI controller on 10020000.sdhci [10020000.sdhci] using ADMA in legacy mode
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Key type dns_resolver registered
hibvt_rtc 120e0000.rtc: setting system clock to 1970-01-01 00:00:00 UTC (0)
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
devtmpfs: mounted
Freeing unused kernel memory: 172K (c04ed000 - c0518000)
This architecture does not have kernel memory protection.
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Loading modules:Initializing random number generator: OK
Saving random seed: OK
Starting rngd: OK
Starting mdev...
Starting network: Cannot parse config file '/etc/fw_env.config': No such file or directory
ip: SIOCGIFINDEX: No such device
FAIL
Starting ntpd: OK
Starting dropbear sshd: OK
Starting mini-snmpd: OK
hisilicon: Check MAC for Xiongmai devices
Cannot parse config file '/etc/fw_env.config': No such file or directory
Cannot parse config file '/etc/fw_env.config': No such file or directory
hisilicon: The eth0 interface has a correct MAC -
hisilicon: Loading of kernel modules and initialization of the video system has started
get_hisi_chip_id() got unexpected 0x3518e300
Cannot parse config file '/etc/fw_env.config': No such file or directory
Cannot parse config file '/etc/fw_env.config': No such file or directory
mmz_start: 0x42000000, mmz_size: 32M
Cannot parse config file '/etc/fw_env.config': No such file or directory
get_hisi_chip_id() got unexpected 0x3518e300
rmmod: can't unload module 'cma_osal': No such file or directory
hisilicon: Get data from ipcinfo and set SENSOR as unknown
Cannot parse config file '/etc/fw_env.config': No such file or directory
Error: environment not initialized
Starting majestic: OK

Welcome to OpenIPC v2.1
hi3518ev300-openipc login:

@dimerr
Copy link
Collaborator

dimerr commented Aug 24, 2021

Sorry ,copy-paste issue, try again

@001Tycoon
Copy link
Author

@dimerr Thanks works

System booted
i have a problem with fw_env.config
root@hi3518ev300-openipc:~# fw_printenv
Cannot parse config file '/etc/fw_env.config': No such file or directory

what information do you need

@dimerr
Copy link
Collaborator

dimerr commented Aug 24, 2021

I believe you need to replace bootloader...

@001Tycoon
Copy link
Author

I tried that

System startup

Uncompress Ok!

U-Boot 2016.11 (May 09 2019 - 15:47:33 +0800)hi3518ev300

Relocation Offset is: 03737000
Relocating to 43f37000, new gd at 43e96ef0, sp at 43e96ed0
SPI Nor:  NAND:  0 MiB
MMC:
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
hisilicon #

System startup

Uncompress Ok!

U-Boot 2020.01 (Sep 02 2020 - 17:34:02 +0800)hi3518ev300

DRAM:  SPI Nor:  hifmc_ip_ver_check(54): Check Flash Memory Controller v100 ...hifmc_ip_ver_check(60):  Found
hifmc_spi_nor_probe(2070): SPI Nor ID Table Version 1.0
hifmc_spi_nor_probe(2095): SPI Nor(cs 0) ID: 0x20 0x70 0x18
hifmc_init_print(2016): Block:64KB hifmc_init_print(2017): Chip:16MB hifmc_init_print(2018): Name:"XM25QH128A"
hifmc100_spi_nor_probe(145): SPI Nor total size: 16MB
NAND:  0 MiB
Loading Environment from SPI Flash... OK
In:    serial
Out:   serial
Err:   serial
Net:   eth0
Error: eth0 address not set.

Hit any key to stop autoboot:  0
hisilicon #

the same mistakes everywhere
where can I get other bootloaders

@dimerr
Copy link
Collaborator

dimerr commented Aug 24, 2021

https://github.com/OpenIPC/openipc-2.1/releases/download/latest/u-boot-hi3518ev300-beta.bin try this

@001Tycoon
Copy link
Author

Hello
@dimerr u-boot-hi3518ev300-beta.bin
After saving the settings saveenv system does not boot.

hisilicon # saveenv
Saving Environment to SPI Flash...
Erasing SPI flash...Writing to SPI flash...done
hisilicon # reset
resetting ...

System startup

nothing more

boots without saveenv

System startup

Uncompress Ok!

U-Boot 2016.11-g0c517e3-dirty (Aug 23 2021 - 16:24:40 +0300)hi3516ev200

Relocation Offset is: 03750000
Relocating to 43f50000, new gd at 43f0fef0, sp at 43f0fed0
SPI Nor:  hifmc_ip_ver_check(44): Check Flash Memory Controller v100 ...hifmc_ip_ver_check(50):  Found
hifmc_spi_nor_probe(1664): SPI Nor ID Table Version 1.0
hifmc_spi_nor_probe(1689): SPI Nor(cs 0) ID: 0x20 0x70 0x18
hifmc_spi_nor_probe(1754): Block:64KB hifmc_spi_nor_probe(1755): Chip:16MB hifmc_spi_nor_probe(1756): Name:"XM25QH128A"
hifmc100_spi_nor_probe(147): SPI Nor total size: 16MB
NAND:  0 MiB
MMC:
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   eth0
Warning: eth0 (eth0) using random MAC address - 42:48:5c:c5:d2:a3

Hit any key to stop autoboot:  0
device 0 offset 0x50000, size 0x200000

SF: 2097152 bytes @ 0x50000 Read: OK
## Booting kernel from Legacy Image at 42000000 ...
   Image Name:   Linux-4.9.37
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1978264 Bytes = 1.9 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Loading Kernel Image ... OK

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 4.9.37 (ingo@acer-p256-m) (gcc version 7.5.0 (Buildroot -g917914b) ) #2 Tue Aug 24 15:03:27 CEST 2021
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt:Machine model: Hisilicon HI3518EV300 DEMO Board
cmz zone is not set!
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: mem=32M console=ttyAMA0,115200 panic=20 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=hi_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data)
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26776K/32768K available (4084K kernel code, 148K rwdata, 912K rodata, 176K init, 243K bss, 5992K reserved, 0K cma-reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xc2800000 - 0xff800000   ( 976 MB)
    lowmem  : 0xc0000000 - 0xc2000000   (  32 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc0405538   (4086 kB)
      .init : 0xc04ec000 - 0xc0518000   ( 176 kB)
      .data : 0xc0518000 - 0xc053d360   ( 149 kB)
       .bss : 0xc053f000 - 0xc057bcc8   ( 244 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:16 nr_irqs:16 16
Gic dist init...
arm_arch_timer: Architected cp15 timer(s) running at 50.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
Switching to timer-based delay loop, resolution 20ns
clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x40008200 - 0x40008258
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Serial: AMBA PL011 UART driver
12040000.uart: ttyAMA0 at MMIO 0x12040000 (irq = 20, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
ssp-pl022 12070000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12070000.spi: mapped registers from 0x12070000 to c2867000
ssp-pl022 12071000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12071000.spi: mapped registers from 0x12071000 to c286b000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
workingset: timestamp_bits=30 max_order=13 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pl061_gpio 120b0000.gpio_chip: PL061 GPIO chip @0x120b0000 registered
pl061_gpio 120b1000.gpio_chip: PL061 GPIO chip @0x120b1000 registered
pl061_gpio 120b2000.gpio_chip: PL061 GPIO chip @0x120b2000 registered
pl061_gpio 120b4000.gpio_chip: PL061 GPIO chip @0x120b4000 registered
pl061_gpio 120b5000.gpio_chip: PL061 GPIO chip @0x120b5000 registered
pl061_gpio 120b6000.gpio_chip: PL061 GPIO chip @0x120b6000 registered
pl061_gpio 120b7000.gpio_chip: PL061 GPIO chip @0x120b7000 registered
pl061_gpio 120b8000.gpio_chip: PL061 GPIO chip @0x120b8000 registered
brd: module loaded
hisi-sfc hisi_spi_nor.0: SPI Nor ID Table Version 1.2
hisi-sfc hisi_spi_nor.0: The ID: 0x20 isn't in the BP table, Current device can't not protect
@spi_nor_scan(), no "m25p,fast-read".
@spi_nor_scan(), modes->rd_modes:0xd.
hisi-sfc hisi_spi_nor.0: (Fast) Read:  opcode=BBh, protocol=122, mode=0, wait=8
hisi-sfc hisi_spi_nor.0: nor->read_opcode[3: Read; 0B: Fast Read; 3B: Dual; BB: Dual IO; 6B: Quad; EB: Quad IO]: 0xbb.
hisi-sfc hisi_spi_nor.0: xm25qh128a (Chipsize 16 Mbytes, Blocksize 64KiB)
5 cmdlinepart partitions found on MTD device hi_sfc
5 cmdlinepart partitions found on MTD device hi_sfc
Creating 5 MTD partitions on "hi_sfc":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000050000 : "env"
0x000000050000-0x000000250000 : "kernel"
0x000000250000-0x000000750000 : "rootfs"
0x000000750000-0x000001000000 : "rootfs_data"
SPI Nand ID Table Version 2.7
Cannot found a valid SPI Nand Device
hisi_spi_nand_probe(175): Error: driver probe, result: -19
No OTP data, festa PHY use default ATE parameters!
festa PHY wait autotrim done timeout!
libphy: hisi_femac_mii_bus: probed
libphy: Fixed MDIO Bus: probed
hisi-femac 10040000.ethernet: connect to PHY failed!
hibvt_rtc 120e0000.rtc: rtc core: registered 120e0000.rtc as rtc0
hibvt_rtc 120e0000.rtc: RTC driver for hibvt enabled
i2c /dev entries driver
hibvt-i2c 12060000.i2c: hibvt-i2c0@100000hz registered
hibvt-i2c 12061000.i2c: hibvt-i2c1@100000hz registered
hibvt-i2c 12062000.i2c: hibvt-i2c2@100000hz registered
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on 10010000.sdhci [10010000.sdhci] using ADMA in legacy mode
mmc1: SDHCI controller on 10020000.sdhci [10020000.sdhci] using ADMA in legacy mode
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Key type dns_resolver registered
mmc0: new high speed SDHC card at address 2167
mmcblk0: mmc0:2167 APPSD 30.2 GiB
 mmcblk0: p1
hibvt_rtc 120e0000.rtc: hctosys: unable to read the hardware clock
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
devtmpfs: mounted
Freeing unused kernel memory: 176K (c04ec000 - c0518000)
This architecture does not have kernel memory protection.
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Loading modules:Initializing random number generator: OK
Saving random seed: OK
Starting rngd: OK
Starting mdev...
mount: mounting /dev/mmcblk0p1 on /mnt/mmcblk0p1 failed: Invalid argument
Starting network: Cannot parse config file '/etc/fw_env.config': No such file or directory
ip: SIOCGIFINDEX: No such device
FAIL
Starting ntpd: OK
Starting dropbear sshd: OK
Starting mini-snmpd: OK
hisilicon: Check MAC for Xiongmai devices
Cannot parse config file '/etc/fw_env.config': No such file or directory
Cannot parse config file '/etc/fw_env.config': No such file or directory
hisilicon: The eth0 interface has a correct MAC -
hisilicon: Loading of kernel modules and initialization of the video system has started
get_hisi_chip_id() got unexpected 0x3518e300
Cannot parse config file '/etc/fw_env.config': No such file or directory
Cannot parse config file '/etc/fw_env.config': No such file or directory
mmz_start: 0x42000000, mmz_size: 32M
Cannot parse config file '/etc/fw_env.config': No such file or directory
get_hisi_chip_id() got unexpected 0x3518e300
rmmod: can't unload module 'cma_osal': No such file or directory
hisilicon: Get data from ipcinfo and set SENSOR as unknown
Cannot parse config file '/etc/fw_env.config': No such file or directory
Error: environment not initialized
Starting majestic: OK

Welcome to OpenIPC v2.1
hi3518ev300-openipc login:

other logs are required?

@dimerr
Copy link
Collaborator

dimerr commented Aug 24, 2021

Try same link, updated

@001Tycoon
Copy link
Author

@dimerr u-boot-hi3518ev300-beta.bin is running now
saveenv is work now
fw_printenv fw_setenv is work now.
Thanks very much

@dimerr dimerr closed this as completed Aug 24, 2021
@001Tycoon 001Tycoon mentioned this issue Aug 26, 2021
Open
@Droid-MAX
Copy link

@dimerr this link are no longer availiable, where can I download that uboot file? thx

@cronyx
Copy link
Member

cronyx commented Nov 28, 2022

https://github.com/OpenIPC/firmware/releases

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Assignees
No one assigned
Labels
None yet
Projects
None yet
Milestone
No milestone
Development

No branches or pull requests
5 participants
@ZigFisher @cronyx @dimerr @Droid-MAX @001Tycoon