What's in a name? sprotly; proxy -> proxly, x -> t for transparent and s for splice, as it uses the Linux splice(2) system call.
sprotly is a tool to sit in front of a proxy such as squid and forward https client requests to the proxy converting them into CONNECT's.
This would be used for cases where you want to be able to perform some action on https requests based purely on destination within squid and don't want them run through SSLBump.
This is done by using an iptables rule to redirect port 443 traffic to a port that sprotly is listening on e.g
# ip6tables -t nat -A PREROUTING -p tcp -m tcp --dport 443 -j REDIRECT --to-ports 3129
# iptables -t nat -A PREROUTING -p tcp -m tcp --dport 443 -j REDIRECT --to-ports 3129
# sprotly -l localhost:3129 -p :9443
Thus any traffic destined for port 443 is redirected to port 3129 where sprotly turns the standard requests into CONNECT's as squid would be expecting them for https requests. The corresponding squid config for this would be
http_port 9443
It then connects to squid on port 9443 (it will try IPv6 first then IPv4) on localhost (by not specifying a host) and sends the CONNECT request, once it gets the OK from squid it then just shuffles packets back and forth between the client and squid.
The only hard requirement is libac. On a rpm based system something like the following should work
$ git clone https://github.com/ac000/libac
$ cd libac
$ cp libac.spec ~/rpmbuild/SPECS
$ git archive --format=tar --prefix=libac-$(grep ^Version libac.spec | cut -f 2)/ -o ~/rpmbuild/SOURCES/libac-$(grep ^Version libac.spec | cut -f 2).tar HEAD
$ rpmbuild -bb ~/rpmbuild/SPECS/libac.spec
$ sudo dnf install ~/rpmbuild/RPMS/x86_64/libac-<VERSION>-?.<DIST>.x86_64.rpm
You can create a suitable rpmbuild tree with
$ mkdir -p ~/rpmbuild/{BUILD,RPMS,SOURCES,SPECS,SRPMS}
sprotly can optionally include support for seccomp via libseccomp if you have it installed, e.g on Red Hat based distros this would be the
libseccomp
libseccomp-devel
packages.
This can be disabled at build time by setting the SPROTLY_SECCOMP shell environment variable to 0. e.g
$ SPROTLY_SECCOMP=0 make
For sprotly
$ git clone https://github.com/ac000/sprotly
$ cd src
$ make
$ sudo install -Dp 0755 sprotly /usr/local/sbin/
sprotly has no configuration file and has only a few options
$ ./sprotly -h
Usage: sprotly [-D] <-l [host]:port[,...]> <-p [proxy]:port> [-s] [-v] [-h]
-D - Run in debug mode. Log goes to terminal and runs in the
foreground.
-l - Listens on the optionally specified host/address(es) and
port(s). If no host is specified uses the unspecified address
(::, 0.0.0.0). Listens on both IPv6 and IPv4.
-p - The optional host/address of the proxy and port to send
requests to. If the host is unspecified uses localhost. Will
try IPv6 first then IPv4.
-s - Disable TLS SNI extraction.
-v - Display the version.
-h - Display this text.
Example -
sprotly -l localhost:3129 -p :9443
-l and -p are the only required options. And the example shown is generally how you'd want to run it.
-l can take a comma separated list of [host]:port pairs.
This will tell sprotly to listen on port 3129 on ::1 and 127.0.0.1 for client requests which have been redirected by the above ip{6}tables rules.
It will then send the CONNECT requests to the proxy running on ::1 or 127.0.0.1 on port 9443.
By default sprotly will try to extract the requested hostname as given in the TLS SNI field from the 'Client Hello' message and use this in the CONNECT requests. If there isn't one it will fall back to using the IP address as retrieved from the network stack.
-s is used to tell sprotly not to do this and just use the IP address.
sprotly uses a multiprocess, multi-threaded architecture.
When started, sprotly will fork a listen process for each cpu in the system. These listen processes wait for new client connections and hand them off to a worker thread.
For the actual sending/receiving of data to/from client/proxy it uses the splice(2) system call which has the potential to allow for zero copy I/O.
However it does make sprotly somewhat file descriptor hungry requiring six fd's per connection. i.e
1 - peer socket
2 - peer pipe read end
3 - peer pipe write end
4 - proxy socket
5 - proxy pipe read end
6 - proxy pipe write end
although on modern 64bit systems with plenty of RAM this shouldn't really be an issue, hence at startup sprotly will attempt to increase RLIMIT_NOFILE to 65536. This limit is per-process and should allow for 10,000+ connections per worker.
When run as root, the worker processes will change to run as the sprotly user. Also sprotly will write to two log files; /var/log/sprotly/access_log and /var/log/sprotly/error_log.
If the sprotly user doesn't exist, then it will try using the 'nobody' user.
You can create a sprotly user like
# useradd -r -d / -s /sbin/nologin sprotly
Also by default sprotly will daemon(3)ize itself. When run in the foreground (-D) sprotly simply logs to the terminal.
sprotly can also optionally do syscall filtering with seccomp(2) via libseccomp if you have it installed.
sprotly is licensed under the GNU General Public License version 2. See GPL-2.0.
src/tls_sni.[ch] are licensed under the BSD 2-clause "Simplified" License, see BSD-2-Clause.
It should be noted that sprotly was heavily influenced by Andi Kleen's eproxy https://github.com/andikleen/eproxy
Patches and/or pull requests should be emailed to the project maintainer
Andrew Clayton <andrew@digital-domain.net>
preferably using git-send-email(1) and git-request-pull(1)
Code should follow the coding style as outlined in CodingStyle.
Also, code should be signed-off. This means adding a line that says
Signed-off-by: Name <email>
at the end of each commit, indicating that you wrote the code and have the right to pass it on as an open source patch.