-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathkeyer_features_and_options_mortty_so2r_with_potentiometer.h
121 lines (112 loc) · 10.6 KB
/
keyer_features_and_options_mortty_so2r_with_potentiometer.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
// compile time features and options - comment or uncomment to add or delete features
// FEATURES add more bytes to the compiled binary, OPTIONS change code behavior
// #define FEATURE_BUTTONS
// #define FEATURE_COMMAND_MODE
// #define FEATURE_COMMAND_LINE_INTERFACE // Command Line Interface functionality
// #define FEATURE_MEMORIES // on the Arduino Due, you must have FEATURE_EEPROM_E24C1024 and E24C1024 EEPROM hardware in order to compile this
// #define FEATURE_MEMORY_MACROS
#define FEATURE_WINKEY_EMULATION // disabling Automatic Software Reset is highly recommended (see documentation)
// #define FEATURE_BEACON // Go into beacon mode if paddle_left pin is LOW at boot up
// #define FEATURE_BEACON_SETTING // Go into beacon mode at boot up if EEPROM setting is enabled (\_ CLI Command)
// #define FEATURE_TRAINING_COMMAND_LINE_INTERFACE
#define FEATURE_POTENTIOMETER // do not enable unless you have a potentiometer connected, otherwise noise will falsely trigger wpm changes
// #define FEATURE_SIDETONE_SWITCH // adds switch control for the sidetone output. requires an external toggle switch (assigned to an arduino pin - see keyer_pin_settings.h).
// #define FEATURE_SERIAL_HELP
// #define FEATURE_HELL
// #define FEATURE_PS2_KEYBOARD // Use a PS2 keyboard to send code - Change keyboard layout (non-US) in K3NG_PS2Keyboard.h. Additional options below.
// #define FEATURE_USB_KEYBOARD // Use a USB keyboard to send code - Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines)
// #define FEATURE_CW_COMPUTER_KEYBOARD // Have an Arduino Due or Leonardo act as a USB HID (Human Interface Device) keyboard and use the paddle to "type" characters on the computer -- uncomment this line in ino file: #include <Keyboard.h>
// #define FEATURE_DEAD_OP_WATCHDOG
// #define FEATURE_AUTOSPACE
// #define FEATURE_FARNSWORTH
// #define FEATURE_DL2SBA_BANKSWITCH // Switch memory banks feature as described here: http://dl2sba.com/index.php?option=com_content&view=article&id=131:nanokeyer&catid=15:shack&Itemid=27#english
// #define FEATURE_LCD_4BIT // classic LCD disidefplay using 4 I/O lines
// #define FEATURE_LCD_ADAFRUIT_I2C // Adafruit I2C LCD display using MCP23017 at addr 0x20
// #define FEATURE_LCD_ADAFRUIT_BACKPACK // Adafruit I2C LCD Backup using MCP23008 (courtesy Josiah Ritchie, KE0BLL)
// #define FEATURE_LCD_YDv1 // YourDuino I2C LCD display with old LCM 1602 V1 ic
// #define FEATURE_LCD1602_N07DH // http://linksprite.com/wiki/index.php5?title=16_X_2_LCD_Keypad_Shield_for_Arduino
// #define FEATURE_LCD_SAINSMART_I2C
// #define FEATURE_LCD_I2C_FDEBRABANDER //https://github.com/fdebrabander/Arduino-LiquidCrystal-I2C-library
// #define FEATURE_CW_DECODER // https://github.com/k3ng/k3ng_cw_keyer/wiki/385-Feature:-CW-Decoder
// #define FEATURE_SLEEP // go to sleep after x minutes to conserve battery power (not compatible with Arduino DUE, may have mixed results with Mega and Mega ADK)
// #define FEATURE_LCD_BACKLIGHT_AUTO_DIM // turn off LCD backlight and/or dim Power Indicator LED after x minutes (LED requires a PWM pin)
// #define FEATURE_ROTARY_ENCODER // rotary encoder speed control
// #define FEATURE_CMOS_SUPER_KEYER_IAMBIC_B_TIMING
// #define FEATURE_USB_MOUSE // Uncomment three lines in k3ng_keyer.ino (search for note_usb_uncomment_lines)
// #define FEATURE_CAPACITIVE_PADDLE_PINS // remove the bypass capacitors on the paddle_left and paddle_right lines when using capactive paddles
// #define FEATURE_LED_RING // Mayhew Labs Led Ring support
// #define FEATURE_ALPHABET_SEND_PRACTICE // enables command mode S command - created by Ryan, KC2ZWM
// #define FEATURE_COMMAND_MODE_PROGRESSIVE_5_CHAR_ECHO_PRACTICE // enables command mode U
// #define FEATURE_PTT_INTERLOCK
// #define FEATURE_QLF
// #define FEATURE_EEPROM_E24C1024
// #define FEATURE_STRAIGHT_KEY
// #define FEATURE_DYNAMIC_DAH_TO_DIT_RATIO
// #define FEATURE_PADDLE_ECHO
// #define FEATURE_STRAIGHT_KEY_ECHO
// #define FEATURE_WEB_SERVER // Details: https://github.com/k3ng/k3ng_cw_keyer/wiki/390-Feature:-Ethernet,-Web-Server,-and-Internet-Linking
// #define FEATURE_INTERNET_LINK // Details: https://github.com/k3ng/k3ng_cw_keyer/wiki/390-Feature:-Ethernet,-Web-Server,-and-Internet-Linking
// #define FEATURE_AMERICAN_MORSE
// #define FEATURE_4x4_KEYPAD // code contributed by Jack, W0XR - documentation: https://github.com/k3ng/k3ng_cw_keyer/wiki/380-Feature:-Keypad
// #define FEATURE_3x4_KEYPAD // code contributed by Jack, W0XR - documentation: https://github.com/k3ng/k3ng_cw_keyer/wiki/380-Feature:-Keypad
// #define FEATURE_COMMAND_MODE_ENHANCED_CMD_ACKNOWLEDGEMENT
// #define FEATURE_WEB_SERVER // Details: https://github.com/k3ng/k3ng_cw_keyer/wiki/390-Feature:-Ethernet,-Web-Server,-and-Internet-Linking
// #define FEATURE_INTERNET_LINK // Details: https://github.com/k3ng/k3ng_cw_keyer/wiki/390-Feature:-Ethernet,-Web-Server,-and-Internet-Linking
// #define FEATURE_COMMAND_LINE_INTERFACE_ON_SECONDARY_PORT // Activate the Command Line interface on the secondary serial port
#define OPTION_PRIMARY_SERIAL_PORT_DEFAULT_WINKEY_EMULATION // Use when activating both FEATURE_WINKEY_EMULATION and FEATURE_COMMAND_LINE_INTERFACE
// simultaneously. This will make Winkey emulation be the default at boot up;
// hold command button down at boot up to activate CLI mode
// #define OPTION_SUPPRESS_SERIAL_BOOT_MSG
#define OPTION_INCLUDE_PTT_TAIL_FOR_MANUAL_SENDING
#define OPTION_EXCLUDE_PTT_HANG_TIME_FOR_MANUAL_SENDING
//#define OPTION_WINKEY_DISCARD_BYTES_AT_STARTUP // if ASR is not disabled, you may need this to discard errant serial port bytes at startup
// #define OPTION_WINKEY_STRICT_EEPROM_WRITES_MAY_WEAR_OUT_EEPROM // with this activated the unit will write non-volatile settings to EEPROM when set by Winkey commands
// #define OPTION_WINKEY_SEND_WORDSPACE_AT_END_OF_BUFFER
// #define OPTION_WINKEY_STRICT_HOST_OPEN // require an admin host open Winkey command before doing any other commands
#define OPTION_WINKEY_2_SUPPORT // comment out to revert to Winkey version 1 emulation
#define OPTION_WINKEY_SEND_BREAKIN_STATUS_BYTE
#define OPTION_WINKEY_INTERRUPTS_MEMORY_REPEAT
//#define OPTION_WINKEY_UCXLOG_9600_BAUD // use this only with UCXLog configured for Winkey 9600 baud mode
#define OPTION_WINKEY_2_HOST_CLOSE_NO_SERIAL_PORT_RESET // activate this when using Winkey 2 emulation and Win-Test
// #define OPTION_WINKEY_FREQUENT_STATUS_REPORT // activate this to make Winkey emulation play better with RUMlog and RUMped
#define OPTION_WINKEY_IGNORE_LOWERCASE // Enable for typical K1EL Winkeyer behavior (use for SkookumLogger version 1.10.14 and prior to workaround "r" bug)
#define OPTION_WINKEY_BLINK_PTT_ON_HOST_OPEN
// #define OPTION_WINKEY_SEND_VERSION_ON_HOST_CLOSE
// #define OPTION_WINKEY_PINCONFIG_PTT_CONTROLS_PTT_LINE // Have Winkeyer PTT setting activate/deactivate PTT line rather than control buffered character PTT hold
// #define OPTION_REVERSE_BUTTON_ORDER // This is mainly for the DJ0MY NanoKeyer http://nanokeyer.wordpress.com/
#define OPTION_PROG_MEM_TRIM_TRAILING_SPACES // trim trailing spaces from memory when programming in command mode
#define OPTION_DIT_PADDLE_NO_SEND_ON_MEM_RPT // this makes dit paddle memory interruption a little smoother
// #define OPTION_MORE_DISPLAY_MSGS // additional optional display messages - comment out to save memory
// #define OPTION_N1MM_WINKEY_TAB_BUG_WORKAROUND // enable this to ignore the TAB key in the Send CW window (this breaks SO2R functionality in N1MM)
// #define OPTION_WATCHDOG_TIMER // this enables a four second ATmega48/88/168/328 watchdog timer; use for unattended/remote operation only
// #define OPTION_MOUSE_MOVEMENT_PADDLE // experimental (just fooling around) - mouse movement will act like a paddle
// #define OPTION_NON_ENGLISH_EXTENSIONS // add support for additional CW characters (i.e. À, Å, Þ, etc.)
// #define OPTION_DISPLAY_NON_ENGLISH_EXTENSIONS // LCD display suport for non-English (NO/DK/DE) characters - Courtesy of OZ1JHM
// #define OPTION_UNKNOWN_CHARACTER_ERROR_TONE
#define OPTION_DO_NOT_SAY_HI
#define OPTION_BLINK_HI_ON_PTT
// #define OPTION_PS2_NON_ENGLISH_CHAR_LCD_DISPLAY_SUPPORT // makes some non-English characters from the PS2 keyboard display correctly in the LCD display (donated by Marcin sp5iou)
// #define OPTION_PS2_KEYBOARD_RESET // reset the PS2 keyboard upon startup with 0xFF (contributed by Bill, W9BEL)
// #define OPTION_SAVE_MEMORY_NANOKEYER
// #define OPTION_CW_KEYBOARD_CAPSLOCK_BEEP
// #define OPTION_CW_KEYBOARD_ITALIAN
// #define OPTION_CW_KEYBOARD_GERMAN
// #define OPTION_CW_DECODER_GOERTZEL_AUDIO_DETECTOR
// #define OPTION_INVERT_PADDLE_PIN_LOGIC
// #define OPTION_ADVANCED_SPEED_DISPLAY //enables "nerd" speed visualization on display: wpm, cpm (char per min), duration of dit and dah in milliseconds and ratio (contributed by Giorgio, IZ2XBZ)
// #define OPTION_PROSIGN_SUPPORT // additional prosign support for paddle and straight key echo on display, CLI, and in memory storage
// #define OPTION_RUSSIAN_LANGUAGE_SEND_CLI // Russian language CLI sending support (contributed by Павел Бирюков, UA1AQC)
#define OPTION_DO_NOT_SEND_UNKNOWN_CHAR_QUESTION
// #define OPTION_CMOS_SUPER_KEYER_IAMBIC_B_TIMING_ON_BY_DEFAULT
#define OPTION_SIDETONE_DIGITAL_OUTPUT_NO_SQUARE_WAVE
// #define OPTION_WORDSWORTH_CZECH
// #define OPTION_WORDSWORTH_DEUTSCH
// #define OPTION_WORDSWORTH_NORSK
#define OPTION_EXCLUDE_EXTENDED_CLI_COMMANDS
// #define OPTION_NO_ULTIMATIC // reduce memory usage by removing ultimatic code.
// #define OPTION_PERSONALIZED_STARTUP_SCREEN // displays a user defined string of characters on the second or fourth row of the screen during startup. 1602 display requires OPTION_DO_NOT_SAY_HI
// #define OPTION_SWAP_PADDLE_PARAMETER_CHANGE_DIRECTION // reverses the up/down direction when using the paddles to change the wpm or sidetone frequency
// #define OPTION_DISPLAY_MEMORY_CONTENTS_COMMAND_MODE
// #define OPTION_BEACON_MODE_MEMORY_REPEAT_TIME // to space out the repeated playing of memory 1 when in beacon mode
// #define OPTION_BEACON_MODE_PTT_TAIL_TIME // adds the ptt tail time to each playing of memory 1 in beacon mode
// #define OPTION_WINKEY_PROSIGN_COMPATIBILITY // Additional character mappings to support K1EL Winkey emulation prosigns