-
Notifications
You must be signed in to change notification settings - Fork 0
/
config.txt
141 lines (112 loc) · 4.77 KB
/
config.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
#############################################################################################
#############################################################################################
################# BELOW ARE SETTINGS SPECIFIC TO THE CRT-Pi PROJECT IMAGES! #################
################# DON'T CHANGE ANYTHING YOU IF YOU DON'T KNOW WHAT IT DOES! #################
################ ONLY UNCOMMENT THE BLOCKS SPECIFIC TO YOUR SPECIFIC DEVICE! ################
#############################################################################################
#############################################################################################
## Analog Audio Settings!!
disable_audio_dither=1
audio_pwm_mode=2
## GPIO Display Settings!!
enable_dpi_lcd=1
display_default_lcd=1
dpi_group=2
dpi_mode=87
#############################################################################################
################# CHOOSE ONLY ONE DISPLAY ADAPTER BLOCK TO UNCOMMENT AT ONE #################
################# TIME! IGNORE THE EXPERIMENTAL BOOT TIMING UNLESS YOU KNOW #################
################## WHAT YOU ARE DOING AND WHY YOU ARE USING IT! GOOD LUCK! ##################
#############################################################################################
## VGA666 only
dtoverlay=vga666
# Stable Boot Timing
#hdmi_timings=640 1 56 56 80 480 0 1 3 25 0 0 0 65 0 36000000 1 #VGA666 Stable 640x480p@65hz
#hdmi_cvt=1280 960 60 1 0 0 0
hdmi_cvt 1280 960 60 1 0 0 0
# Test Timings
#hdmi_timings=640 0 16 64 120 480 0 1 3 16 0 0 0 75 0 31500000 1 #VGA666 Experimental 480P@75hz YES SYNC + BOWING
#hdmi_timings=2048 1 180 202 300 480 1 6 10 28 0 0 0 60 0 85909090 1 #480p@60hz Retrotink Lakka
#hdmi_timings=2048 1 180 202 300 240 1 3 5 14 0 0 0 120 0 85909090 1 #240p@120Hz Retrotink Lakka
#hdmi_timings=640 0 16 96 48 480 0 10 2 33 0 0 0 60 0 25175000 1 #VGA666 480p@60hz Experimental NO SYNC
# Disable Monitor EDID
hdmi_ignore_edid=0xa5000080
hdmi_ignore_cec_init=1
# Uncomment for TATE mode (270 Degree)
#display_lcd_rotate=3
#############################################################################################
#############################################################################################
## For more options and information see
## http://rpf.io/configtxt
## Some settings may impact device functionality. See link above for details
## Uncomment to disable rainbow splash on boot
disable_splash=1
boot_delay=1
## Uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
## Uncomment this if your display has a black border of unused pixels visible and your display can output without overscan
#disable_overscan=1
## Uncomment the following to adjust overscan. Use positive numbers if console goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
## Uncomment to force a console size. By default it will be display's size minus overscan.
#framebuffer_width=1280
#framebuffer_height=720
## Uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
## Uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
## Uncomment to force a HDMI mode rather than DVI. This can make audio work in DMT (computer monitor) modes
hdmi_drive=2
#hdmi_ignore_cec_init=1
## Uncomment to increase signal to HDMI, if you have interference, blanking, or no display
#config_hdmi_boost=4
## Uncomment for composite PAL
#sdtv_mode=2
## Uncomment to overclock the Pi2. 900 MHz is the default.
#total_mem=1024
#arm_freq=1000
#gpu_freq=500
#core_freq=500
#sdram_freq=500
#sdram_schmoo=0x02000020
#over_voltage=2
#sdram_over_voltage=2
## Uncomment to overclock the Pi3B. **DO NOT USE FOR 3B+** 1200 MHz is the default.
#total_mem=1024
#arm_freq=1300
#gpu_freq=500
#core_freq=500
#sdram_freq=500
#sdram_schmoo=0x02000020
#over_voltage=2
#sdram_over_voltage=2
## Uncomment to overclock the Pi3B+. **DO NOT USE FOR 3B** 1400 Mhz is the default.
#total_mem=1024
#arm_freq=1425
#core_freq=600
#v3d_freq=400
#sdram_freq=550
#over_voltage=1
#temp_soft_limit=70
## You can also raise the minimum frequency of the dynamic clock (Defaults are 600 & 250 for Pi3B+)
#arm_freq_min=900
#core_freq_min=325
## Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
## Additional overlays and parameters are documented /boot/overlays/README
## Enable audio (loads snd_bcm2835)
dtparam=audio=on
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
#overscan_scale=1
#############################################################################################
#############################################################################################