-
Notifications
You must be signed in to change notification settings - Fork 0
/
printer-20231025_111941.cfg
126 lines (100 loc) · 3.04 KB
/
printer-20231025_111941.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
# Prusa MK3s Klipper Config
# You'll be able to print just fine with this config as it is, but it is recommended
# that you follow these steps to properly calibrate your printer:
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
# 2) Skew Correction: https://www.klipper3d.org/skew_correction.html
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
# Read more about klipper here: https://www.klipper3d.org/Overview.html
### UI
[include mainsail.cfg]
[exclude_object]
[mcu]
# serial: /dev/serial0 # If you are using internal RPI serial port
serial: /dev/ttyACM0 # If you are using RPI via USB connection to printer
restart_method: command
### CONTROL BOARD
[include einsy-rambo.cfg]
### BASE SETUP
[include display.cfg]
[include steppers.cfg]
[include tmc2130.cfg]
### EXTRUSION
# Extruder
[include extruder.cfg]
# Hotend
[include mosquito.cfg]
[include KAMP_Settings.cfg]
[extruder]
# To tune Pressure Advance see https://www.klipper3d.org/Pressure_Advance.html
# default is already set based on hotend, but you can further improve prints by calibrating it to your nozzle and material
# pressure_advance: 0.05
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
## copy this from your current setting on Prusa, but make it absolute (removing -)
[probe]
#z_offset = 1.400
## For faster printing enable
[printer]
max_accel: 2000
max_accel_to_decel: 2000
max_z_velocity: 20
max_z_accel: 300
## Custom bed mest probes
## Prusa has 3x3 or 7x7, you can do any variation you want
[bed_mesh]
probe_count: 3,3
# Linear correction
# Default Prusa linear correction optimized for LDO motors
[include linear-correction-0.cfg]
### MACROS
[include macros.cfg]
[include config_backup.cfg]
[include auto_speed.cfg]
[include flexplate.cfg]
# File location of stored varibales
[save_variables]
filename: /home/pi/printer_data/config/.variables.stb
#If not using with Octoprint remove the menu.
[menu __main __octoprint]
type: disabled
# FIRST RUN:
# Execute these sequentially in the console, let PID tuning finish before saving
# PID_CALIBRATE HEATER=extruder TARGET=170
# SAVE_CONFIG
# PID_CALIBRATE HEATER=heater_bed TARGET=60
# SAVE_CONFIG
### The end, on the end the printer will store it's tuning data, so do not edit it.
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 19.369
#*# pid_ki = 0.787
#*# pid_kd = 119.122
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 49.655
#*# pid_ki = 0.584
#*# pid_kd = 1055.799
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 0.127500, 0.098611, -0.065417
#*# 0.264722, 0.016667, -0.055833
#*# 0.203333, 0.057500, 0.004167
#*# x_count = 3
#*# y_count = 3
#*# mesh_x_pps = 3
#*# mesh_y_pps = 3
#*# algo = lagrange
#*# tension = 0.2
#*# min_x = 24.0
#*# max_x = 228.0
#*# min_y = 6.0
#*# max_y = 210.0
#*#
#*# [probe]
#*# z_offset = -0.130