Skip to content

Latest commit

 

History

History
103 lines (101 loc) · 4.79 KB

README.md

File metadata and controls

103 lines (101 loc) · 4.79 KB

SNAP board control

Requirements

Miniconda3 is suggested for the control scripts.

  1. casperfpga
    You need to install py38 branch.
  2. other necessary packages
    pip install redis
    pip install matplotlib
    pip install scipy
    pip install jupyter
    pip install nbconvert

Directory Structure

ipynb

  • snap_init.ipynb: This Jupyter Notebook is used for configuring SNAP board.
  • snap_adc.ipynb: This Jupyter Notebook is used for testing adcs on SNAP board.

scripts

  • gen_py.sh: This script is used for generating python scripts from the above Jupyter Notebook.
  • snap_init.py and snap_adc.py: There are two python scripts, which are generated from the related *.ipynb files.
  • check_status.py: It's used for checking SNAP board status, inclduing ADC rms and clock frequency.
    You can run python check_status.py -h to get more options.
    (py38) ~limbo_scripts/scripts$ python check_status.py --all
    **************************************
    --SNAP Board IP:  192.168.2.100
    **************************************
    Fabric Clock Freq : 250.328834 MHz
      RMS of ADC_I : 10.398341
      RMS of ADC_Q : 15.032874
    **************************************

NOTE:

  1. Before running this script, please make sure the SNAP board has been programmed;
  2. the default IP of SNAP board is 192.168.2.100;
  3. the default port for SNAP board communication is 69;
  4. the default fpg file is limbo_500_2022-12-03_1749.fpg;

fpg

The fpg files used in the scripts are here.

figures

limbo-block-diagram: It shows the registers used in the FPGA design. You can change these register values in the snap_init.py.

figure

Getting Start

There are two ways to configure the SNAP board.

Method1: Jupyter Notebook

Go to ./ipynb, and then open snap_init.ipynb.
Run the cells step by step.

Method2: command line

Go to ./scripts, and run

    python snap_init.py

IP configuration after power cycle

The SNAP board gets an IP from the DHCP server.
Let's assume the SNAP configuration port is connected to enp30s port on a server(limbo server at Leuscher), where a DHCP server(dnsmasq) is running.
When we have a power cycle, what we need to do to get the SNAP board back online is:

  1. run ifconfig on the server to check if the port is up. If it's up, you should see a IP address bind on this port: 
     ~$ ifconfig
 enp3s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 9000
     inet 192.168.2.1  netmask 255.255.255.0  broadcast 192.168.2.255
     inet6 fe80::f652:14ff:fe16:24a0  prefixlen 64  scopeid 0x20<link>
     ether f4:52:14:16:24:a0  txqueuelen 1000  (Ethernet)
     RX packets 3889203  bytes 15899182864 (15.8 GB)
     RX errors 0  dropped 0  overruns 0  frame 0
     TX packets 62602  bytes 10523830 (10.5 MB)
     TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
    If we can't see the IP address, it means the link is not up. We need to check if the SNAP board is powered on. Or we need to run sudo netplan apply to set the IP.
  2. make sure the DHCP server is running: 
     ~$ sudo systemctl status dnsmasq.service 
  dnsmasq.service - dnsmasq - A lightweight DHCP and caching DNS server
  Loaded: loaded (/lib/systemd/system/dnsmasq.service; enabled; vendor preset: enabled)
  Active: active (running) since Fri 2024-02-23 19:02:22 UTC; 1h 13min ago
 Process: 1378774 ExecStartPre=/usr/sbin/dnsmasq --test (code=exited, status=0/SUCCESS)
 Process: 1378785 ExecStart=/etc/init.d/dnsmasq systemd-exec (code=exited, status=0/SUCCESS)
 Process: 1378795 ExecStartPost=/etc/init.d/dnsmasq systemd-start-resolvconf (code=exited, status=0/SUCCESS)
Main PID: 1378794 (dnsmasq)
   Tasks: 1 (limit: 38371)
  Memory: 3.1M
  CGroup: /system.slice/dnsmasq.service
          └─1378794 /usr/sbin/dnsmasq -x /run/dnsmasq/dnsmasq.pid -u dnsmasq -7 /etc/dnsmasq.d,.dpkg-dist,.dpkg-old,.dpkg-new --local-servi>
    If the DHCP server is not running, we need to restart the dnsmasq.service, and then check the status again. 
     ~$ sudo systemctl restart dnsmasq.service 
 ~$ sudo systemctl status dnsmasq.service
  3. If the DHCP server is running, you should be able to see the IP address of the SNAP board from the lease file: 
     ~$ cat /var/lib/misc/dnsmasq.leases 
 1708758448 00:08:0b:c4:17:01 192.168.2.100 * *
    Note: The IP address of the SNAP board at Leuschner is bind to 192.168.2.100 in /etc/ethers: 
     ~$ cat /etc/ethers
 # SNAP for limbo
 00:08:0b:c4:17:01 192.168.2.100
    If you want to change the IP address, you need to edit this file, and restart the dnsmasq service.