+++ archetype = "section" title = "[ESP100]" weight = 800 +++

Set / Display Station SSID

Input

[ESP100]<SSID> json=<no> pwd=<admin/user password>

json=no the output format
can be in JSON or plain text
pwd= the admin password if authentication is enabled
SSID
- if SSID is empty, it will display current SSID
- if SSID is not empty, it will set the SSID

Output

In json format

{
   "cmd":"100",
   "status":"ok",
   "data":"esp3d"
}

cmd Id of requested command, should be 100
status status of command, should be ok
data content of response, here the SSID

+++ archetype = "section" title = "[ESP101]" weight = 800 +++ Set Station Password

Input

[ESP101]<password> <NOPASSWORD> json=<no> pwd=<admin/user password>

json=no the output format
can be in JSON or plain text
pwd= the admin password if authentication is enabled
password
- if password is not empty, it will set the password
NOPASSWORD
- if NOPASSWORD is present, it will remove the password
if password is empty and NOPASSWORD is not present, it will raise error: `Password not displayable``

Output

In json format

{
   "cmd":"101",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 101
status status of command, should be ok
data content of response, here ok

if error :

json format :

{
"cmd":"101",
"status":"error",
"data":"Password not displayable"
}

plain text : `error: Password not displayable`

+++ archetype = "section" title = "[ESP102]" weight = 800 +++ Set / Display Station IP mode

Input

[ESP102]<mode> json=<no> pwd=<admin/user password>

json=no the output format
can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: DHCP or STATIC

Output

In json format

{
   "cmd":"102",
   "status":"ok",
   "data":"DHCP"
}

cmd Id of requested command, should be 102
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP103]" weight = 800 +++ Set / Display Station IP address

Input

[ESP103]IP=<IP> MSK=<IP> GW=<IP> DNS=<IP> json=<no> pwd=<admin/user password>

json=no the output format
can be in JSON or plain text
pwd= the admin password if authentication is enabled
IP
- if IP is empty, it will display defined IP
- if IP is not empty, it will set the IP
MSK
- if MSK is empty, it will display defined Network Mask
- if MSK is not empty, it will set the Network Mask
GW
- if GW is empty, it will display defined Gateway
- if GW is not empty, it will set the Gateway
DNS
- if DNS is empty, it will display defined DNS
- if DNS is not empty, it will set the DNS

Output

In json format

{
 "cmd": "103",
 "status": "ok",
 "data": {
  "ip": "192.168.0.1",
  "gw": "192.168.0.1",
  "msk": "255.255.255.0",
  "dns": "192.168.0.1"
 }
}

cmd Id of requested command, should be 103
status status of command, should be ok
data content of response, here the IP, GW, MSK and DNS

+++ archetype = "section" title = "[ESP104]" weight = 800 +++ Set station fallback mode state at boot which can be BT, WIFI-SETUP, OFF

Input

[ESP104]<mode> json=<no> pwd=<admin/user password>

json=no the output format
can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: BT, WIFI-SETUP or OFF

Output

In json format

{
   "cmd":"104",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 104
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP105]" weight = 800 +++ Set / Display Access point SSID

Input

[ESP105]<SSID> json=<no> pwd=<admin/user password>

json=no the output format
can be in JSON or plain text
pwd= the admin password if authentication is enabled
SSID
- if SSID is empty, it will display current SSID
- if SSID is not empty, it will set the SSID

Output

In json format

{
   "cmd":"105",
   "status":"ok",
   "data":"esp3d"
}

cmd Id of requested command, should be 105
status status of command, should be ok
data content of response, here the SSID

+++ archetype = "section" title = "[ESP106]" weight = 800 +++ Set Access point password

Input

[ESP106]<password> <NOPASSWORD> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
password
- if password is not empty, it will set the password
NOPASSWORD
- if NOPASSWORD is present, it will remove the password
if password is empty and NOPASSWORD is not present, it will raise error: `Password not displayable``

Output

In json format

{
   "cmd":"106",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 106
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP107]" weight = 800 +++ Set / Display Access point IP value

Input

[ESP107]<IP> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
IP
- if IP is empty, it will display defined IP
- if IP is not empty, it will set the IP

Output

In json format

{
   "cmd":"107",
   "status":"ok",
   "data":"192.168.0.1"
}

cmd Id of requested command, should be 107
status status of command, should be ok
data content of response, here the IP

+++ archetype = "section" title = "[ESP108]" weight = 800 +++ Set / Display Access point channel value

Input

[ESP108]<channel> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
channel
- if channel is empty, it will display defined channel
- if channel is not empty, it will set the channel

Output

In json format

{
   "cmd":"108",
   "status":"ok",
   "data":"1"
}

cmd Id of requested command, should be 108
status status of command, should be ok
data content of response, here the channel

+++ archetype = "section" title = "[ESP110]" weight = 800 +++ Set radio state at boot which can be BT, WIFI-STA, WIFI-AP, ETH-STA, OFF

Input

[ESP110]<mode> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: BT, WIFI-STA, WIFI-AP, ETH-STA or OFF

Output

In json format

{
   "cmd":"110",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 110
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP111]" weight = 800 +++ Display current IP

Input

[ESP111]<OUTPUT=PRINTER> <ALL> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
OUTPUT
- if OUTPUT is empty, it will display current IP as text 192.168.0.1
- if OUTPUT is PRINTER, it will display current IP in printer format M117 192.168.0.1
ALL
- it is set it will display IP, GW, MSK, DNS ip

Output

In json format

{
   "cmd":"111",
   "status":"ok",
   "data":"192.168.0.1"
}

cmd Id of requested command, should be 111
status status of command, should be ok
data content of response, here the IP

+++ archetype = "section" title = "[ESP112]" weight = 800 +++ Set / Display Hostname

Input

[ESP112]<hostname> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
hostname
- if hostname is empty, it will display current hostname
- if hostname is not empty, it will set the hostname

Output

In json format

{
   "cmd":"112",
   "status":"ok",
   "data":"esp3d"
}

cmd Id of requested command, should be 112
status status of command, should be ok
data content of response, here the hostname

+++ archetype = "section" title = "[ESP114]" weight = 800 +++ Get/Set Boot radio state which can be ON, OFF

Input

[ESP114]<mode> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: ON or OFF

Output

In json format

{
   "cmd":"114",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 114
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP115]" weight = 800 +++ Get/Set immediate Network (WiFi/BT/Ethernet) state which can be ON, OFF

Input

[ESP115]<mode> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: ON or OFF

Output

In json format

{
   "cmd":"115",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 115
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP120]" weight = 800 +++ Get/Set HTTP state which can be ON, OFF

Input

[ESP120]<mode> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: ON or OFF

Output

In json format

{
   "cmd":"120",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 120
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP121]" weight = 800 +++ Get/Set HTTP port

Input

[ESP121]<port> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
port
- if port is empty, it will display current port
- if port is not empty, it will set the port

Output

In json format

{
   "cmd":"121",
   "status":"ok",
   "data":"80"
}

cmd Id of requested command, should be 121
status status of command, should be ok
data content of response, here the port

+++ archetype = "section" title = "[ESP130]" weight = 800 +++ Get/Set TELNET state which can be ON, OFF, CLOSE

Input

[ESP130]<mode> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: ON, OFF or CLOSE

Output

In json format

{
   "cmd":"130",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 130
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP131]" weight = 800 +++ Get/Set TELNET port

Input

[ESP131]<port> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
port
- if port is empty, it will display current port
- if port is not empty, it will set the port

Output

In json format

{
   "cmd":"131",
   "status":"ok",
   "data":"23"
}

cmd Id of requested command, should be 131
status status of command, should be ok
data content of response, here the port

+++ archetype = "section" title = "[ESP140]" weight = 800 +++ Sync / Set / Get current time

Input

[ESP140]<SYNC> <srv1=XXXXX> <srv2=XXXXX> <srv3=XXXXX> <tzone=+HH:SS> <ntp=YES/NO> <time=YYYY-MM-DDTHH:mm:ss> NOW json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
srv1 / srv2 / srv3
- if srv1 / srv2 / srv3 are empty, it will display current NTP servers
- if srv1 / srv2 / srv3 are not empty, it will set the NTP servers
tzone
- if tzone is empty, it will display current time zone
- if tzone is not empty, it will set the time zone
time
- if time is empty, it will display current time
- if time is not empty, it will set the time
ntp
- if ntp is empty, it will display current NTP state
- if ntp is not empty, it will set the NTP state
SYNC
- if SYNC, it will restart NTP service to sync time
NOW
- if NOW, it will display current time in ISO 8601 format with time zone

Output

In json format

{
   "cmd":"140",
   "status":"ok",
   "data":"2020-01-01T00:00:00 (+08:00)"
}

cmd Id of requested command, should be 140
status status of command, should be ok
data content of response, here the time

+++ archetype = "section" title = "[ESP150]" weight = 800 +++ Get/Set display/set boot delay in ms / Verbose boot

Input

[ESP150]<delay=time in milliseconds> <verbose=ON/OFF> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
delay
- if delay is empty, it will display current delay
- if delay is not empty, it will set the delay
verbose
- if verbose is empty, it will display current verbose state
- if verbose is not empty, it will set the verbose state

Output

In json format

{
   "cmd":"150",
   "status":"ok",
   "data": {
      "delay": "100",
      "verbose": "OFF"
    }
}

cmd Id of requested command, should be 150
status status of command, should be ok
data content of response, here the delay and verbose state

+++ archetype = "section" title = "[ESP160]" weight = 800 +++ Get/Set WebSocket state which can be ON, OFF, CLOSE

Input

[ESP160]<mode> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
mode
- if mode is empty, it will display current mode
- if mode is not empty, it will set the setting mode: ON, OFF or CLOSE

Output

In json format

{
   "cmd":"160",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 160
status status of command, should be ok
data content of response, here the mode

+++ archetype = "section" title = "[ESP161]" weight = 800 +++ Get/Set WebSocket port

Input

[ESP161]<port> json=<no> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
port
- if port is empty, it will display current port
- if port is not empty, it will set the port

Output

In json format

{
   "cmd":"161",
   "status":"ok",
   "data":"81"
}

cmd Id of requested command, should be 161
status status of command, should be ok
data content of response, here the port

+++ archetype = "section" title = "[ESP170]" weight = 800 +++ Set Camera command value / list all values in JSON/plain text

Input

[ESP170]<label=value> <json=no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
label
- if label is empty, it will display current value
- if label is not empty, it will set the value
label can be: light/framesize/quality/contrast/brightness/saturation/gainceiling/colorbar/awb/agc/aec/hmirror/vflip/awb_gain/agc_gain/aec_value/aec2/cw/bpc/wpc/raw_gma/lenc/special_effect/wb_mode/ae_level
value depend on label

Output

In json format

{
   "cmd":"170",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 170
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP171]" weight = 800 +++ Save frame to target path and filename (default target = today date, default name=timestamp.jpg)

Input

[ESP171]<json=no> path=<target path> filename=<target filename> pwd=<admin/user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
path
- if path is not empty, it will set the path
filename
- if filename is not empty, it will set the filename

Output

In json format

{
   "cmd":"171",
   "status":"ok",
   "data":"Snapshot taken"
}

cmd Id of requested command, should be 171
status status of command, should be ok
data content of response, here Snapshot taken

+++ archetype = "section" title = "[ESP180]" weight = 800 +++ Get/Set Ftp state which can be ON, OFF, CLOSE

Input

[ESP180]<state> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
state
- if state is empty, it will display current state
- if state is not empty, it will set the state ON, OFF, CLOSE

Output

In json format

{
   "cmd":"180",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 180
status status of command, should be ok
data content of response, here the state

+++ archetype = "section" title = "[ESP181]" weight = 800 +++ Get/Set Ftp ports

Input

ESP181]ctrl=<port> active=<port> passive=<port> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
ctrl
- if ctrl is empty, it will display current ctrl port
- if ctrl is not empty, it will set the ctrl port
active
- if active is empty, it will display current active port
- if active is not empty, it will set the active port
passive
- if passive is empty, it will display current passive port
- if passive is not empty, it will set the passive port

+++ archetype = "section" title = "[ESP190]" weight = 800 +++ Set WebDav state which can be ON, OFF, CLOSE

Input

[ESP190]<state> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
state
- if state is empty, it will display current state
- if state is not empty, it will set the state ON, OFF, CLOSE

Output

In json format

{
   "cmd":"190",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 190
status status of command, should be ok
data content of response, here the state

+++ archetype = "section" title = "[ESP191]" weight = 800 +++ Get/Set WebDav port

Input

[ESP191]<port> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
- port
  - if port is empty, it will display current port
  - if port is not empty, it will set the port

Output

In json format

{
   "cmd":"191",
   "status":"ok",
   "data":"80"
}

cmd Id of requested command, should be 191
status status of command, should be ok
data content of response, here the port

+++ archetype = "section" title = "[ESP200]" weight = 800 +++ Get/Set SD state

Input

[ESP200] json=<YES/NO> <RELEASESD> <REFRESH> pwd=<user/admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
- RELEASESD
  - if RELEASESD is present, it will release SD card
- REFRESH
  - if REFRESH is present, it will refresh SD card

Output

In json format

{
   "cmd":"200",
   "status":"ok",
   "data":"ok"
}

states can be : Busy. "Not available, ok, No SD card

cmd Id of requested command, should be 200
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP201]" weight = 800 +++ Get/Set pin value

Input

[ESP201]P=<pin> V=<value> <json=YES/NO> <PULLUP=YES> <RAW=YES> <ANALOG=NO> <ANALOG_RANGE=255> pwd=<admin password> Range can be 255 / 1024 / 2047 / 4095 / 8191

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
- P
  - if P is not empty, it will use the pin value
- V
  - if V is empty, it will display current pin value
  - if V is not empty, it will set the pin value
RAW
- if RAW is present, it will set the pin mode
PULLUP
- if PULLUP is present, it will set the pullup pin mode
ANALOG
- if ANALOG is present, it will set the pin ANALOG
ANALOG_RANGE
- if ANALOG_RANGE is not empty, it will set the ANALOG_RANGE

Output

In json format

{
   "cmd":"201",
   "status":"ok",
   "data":"1"
}

cmd Id of requested command, should be 201
status status of command, should be ok
data content of response, here the pin value is 1 or High

+++ archetype = "section" title = "[ESP202]" weight = 800 +++ Get/Set SD card Speed factor 1 2 4 6 8 16 32

Input

[ESP202]SPEED=<factor> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
SPEED=
- if factor is empty, it will display current factor
- if factor is not empty, it will set the factor

Output

In json format

{
   "cmd":"202",
   "status":"ok",
   "data":"1"
}

cmd Id of requested command, should be 202
status status of command, should be ok
data content of response, here the current SPI factor

+++ archetype = "section" title = "[ESP210]" weight = 800 +++ Get Sensor Value / type/Set Sensor type

Input

[ESP210]<type=NONE/xxx> <interval=XXX in millisec> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
- type
  - if type is empty, it will display current type
  - if type is not empty, it will set the type
- interval
  - if interval is empty, it will display current interval
  - if interval is not empty, it will set the interval

Output

In json format

{
   "cmd":"210",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 210
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP212]" weight = 800 +++ Output to printer screen status

Input

[ESP212]<Text> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
Text
- if Text is not empty, it will set the Text
- if Text is empty, it will clear current Text

Output

In json format

{
   "cmd":"212",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 212
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP214]" weight = 800 +++ Output to esp screen status

Input

[ESP214]<Text> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
Text
- if Text is not empty, it will set the Text
- if Text is empty, it will clear current Text

Output

In json format

{
   "cmd":"214",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 214
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP215]" weight = 800 +++ Start a Touch Calibration

Input

[ESP215]<CALIBRATE> json=<no> pwd=<admin password>

json=no the output format
pwd= the admin password if authentication is enabled
CALIBRATE
- if CALIBRATE is present, it will start the calibration

Output

In json format

{
   "cmd":"215",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 215
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP220]" weight = 800 +++ Get ESP pins definition

Input

[ESP220] json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled

Output

In json format

{
 "cmd": "220",
 "status": "ok",
 "data": [
  {
   "id": "SD CS",
   "value": "13"
  },
  {
   "id": "SD MOSI",
   "value": "15"
  },
  {
   "id": "SD MISO",
   "value": "2"
  },
  {
   "id": "SD SCK",
   "value": "14"
  },
  {
   "id": "SD DETECT",
   "value": "-1"
  },
  {
   "id": "SD SWITCH",
   "value": "26"
  }
 ]
}

cmd Id of requested command, should be 220
status status of command, should be ok
data content of response, here the pins definitions

plain text format

SD CS: 13
SD MOSI: 15
SD MISO: 2
SD SCK: 14
SD DETECT: -1
SD SWITCH: 26

+++ archetype = "section" title = "[ESP250]" weight = 800 +++ Play sound

Input

[ESP250]F=<frequency> D=<duration> json=<no> pwd=<user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
F
- if F is empty, it will use current frequency
- if F is not empty, it will use the frequency
D
- if D is empty, it will use current duration
- if D is not empty, it will use the duration

Output

In json format

{
   "cmd":"250",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 250
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP290]" weight = 800 +++ Delay/Pause command

Input

[ESP290]<delay in ms> json=<no> pwd=<user password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
delay
- if delay is empty, it will use 0 delay
- if delay is not empty, it will use the delay

Output

In json format

{
   "cmd":"290",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 290
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP400]" weight = 800 +++ Get full ESP3D settings

Input

[ESP400] json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled

Output

Passwords are not displayed and replaced by ********

if json

{"cmd":"400","status":"ok","data":[
{"F":"network/network","P":"130","T":"S","R":"1","V":"esp3d","H":"hostname" ,"S":"32", "M":"1"},
{"F":"network/network","P":"0","T":"B","R":"1","V":"1","H":"radio mode","O":[{"none":"0"},
{"sta":"1"},
{"ap":"2"},
{"setup":"5"}]},
{"F":"network/network","P":"1034","T":"B","R":"1","V":"1","H":"radio_boot","O":[{"no":"0"},
{"yes":"1"}]},
{"F":"network/sta","P":"1","T":"S","V":"Luc-Lab","S":"32","H":"SSID","M":"1"},
{"F":"network/sta","P":"34","T":"S","N":"1","MS":"0","R":"1","V":"********","S":"64","H":"pwd","M":"8"},
{"F":"network/sta","P":"99","T":"B","R":"1","V":"1","H":"ip mode","O":[{"dhcp":"1"},
{"static":"0"}]},
{"F":"network/sta","P":"100","T":"A","R":"1","V":"192.168.0.1","H":"ip"},
{"F":"network/sta","P":"108","T":"A","R":"1","V":"192.168.0.1","H":"gw"},
{"F":"network/sta","P":"104","T":"A","R":"1","V":"255.255.255.0","H":"msk"},
{"F":"network/sta","P":"1029","T":"A","R":"1","V":"192.168.0.1","H":"DNS"},
{"F":"network/sta","P":"1035","T":"B","R":"0","V":"5","H":"sta fallback mode","O":[{"none":"0"},
{"setup":"5"}]},
{"F":"network/ap","P":"218","T":"S","R":"1","V":"ESP3D","S":"32","H":"SSID","M":"1"},
{"F":"network/ap","P":"251","T":"S","N":"1","MS":"0","R":"1","V":"********","S":"64","H":"pwd","M":"8"},
{"F":"network/ap","P":"316","T":"A","R":"1","V":"192.168.0.1","H":"ip"},
{"F":"network/ap","P":"118","T":"B","R":"1","V":"11","H":"channel","O":[{"1":"1"},
{"2":"2"},
{"3":"3"},
{"4":"4"},
{"5":"5"},
{"6":"6"},
{"7":"7"},
{"8":"8"},
{"9":"9"},
{"10":"10"},
{"11":"11"},
{"12":"12"},
{"13":"13"},
{"14":"14"}]},
{"F":"service/http","P":"328","T":"B","R":"1","V":"1","H":"enable","O":[{"no":"0"},{"yes":"1"}]},
{"F":"service/http","P":"121","T":"I","R":"1","V":"8181","H":"port","S":"65001","M":"1"},
{"F":"service/telnetp","P":"329","T":"B","R":"1","V":"1","H":"enable","O":[{"no":"0"},{"yes":"1"}]},
{"F":"service/telnetp","P":"125","T":"I","R":"1","V":"23","H":"port","S":"65001","M":"1"},
{"F":"service/webdavp","P":"1024","T":"B","R":"1","V":"1","H":"enable","O":[{"no":"0"},{"yes":"1"}]},
{"F":"service/webdavp","P":"1025","T":"I","R":"1","V":"80","H":"port","S":"65001","M":"1"},
{"F":"service/time","P":"120","T":"B","V":"1","H":"i-time","O":[{"no":"0"},{"yes":"1"}]},
{"F":"service/time","P":"1042","T":"S","R":"1","V":"+08:00","H":"tzone","O":[{"-12:00":"-12:00"},
{"-11:00":"-11:00"},
{"-10:00":"-10:00"},
{"-09:00":"-09:00"},
{"-08:00":"-08:00"},
{"-07:00":"-07:00"},
{"-06:00":"-06:00"},
{"-05:00":"-05:00"},
{"-04:00":"-04:00"},
{"-03:30":"-03:30"},
{"-03:00":"-03:00"},
{"-02:00":"-02:00"},
{"-01:00":"-01:00"},
{"+00:00":"+00:00"},
{"+01:00":"+01:00"},
{"+02:00":"+02:00"},
{"+03:00":"+03:00"},
{"+03:30":"+03:30"},
{"+04:00":"+04:00"},
{"+04:30":"+04:30"},
{"+05:00":"+05:00"},
{"+05:30":"+05:30"},
{"+05:45":"+05:45"},
{"+06:00":"+06:00"},
{"+06:30":"+06:30"},
{"+07:00":"+07:00"},
{"+08:00":"+08:00"},
{"+08:45":"+08:45"},
{"+09:00":"+09:00"},
{"+09:30":"+09:30"},
{"+10:00":"+10:00"},
{"+10:30":"+10:30"},
{"+11:00":"+11:00"},
{"+12:00":"+12:00"},
{"+12:45":"+12:45"},
{"+13:00":"+13:00"},
{"+14:00":"+14:00"}]},
{"F":"service/time","P":"464","T":"S","R":"1","V":"time.windows.com","S":"128","H":"t-server","M":"0"},
{"F":"service/time","P":"593","T":"S","R":"1","V":"time.google.com","S":"128","H":"t-server","M":"0"},
{"F":"service/time","P":"722","T":"S","R":"1","V":"0.pool.ntp.org","S":"128","H":"t-server","M":"0"},
{"F":"service/notification","P":"1022","T":"B","R":"1","V":"1","H":"auto notif","O":[{"no":"0"},{"yes":"1"}]},
{"F":"service/notification","P":"116","T":"B","R":"1","V":"0","H":"notification","O":[{"none":"0"},
{"pushover":"1"},
{"email":"2"},
{"line":"3"},
{"telegram":"4"},
{"IFTTT":"5"}]},
{"HomeAssistant":"6"}]},
{"F":"service/notification","P":"332","T":"S","R":"1","V":"********","S":"63","H":"t1","M":"0"},
{"F":"service/notification","P":"396","T":"S","R":"1","V":"********","S":"63","H":"t2","M":"0"},
{"F":"service/notification","P":"856","T":"S","R":"1","V":" ","S":"128","H":"ts","M":"0"},
{"F":"system/system","P":"461","T":"B","V":"0","H":"targetfw","O":[{"repetier":"50"},
{"marlin":"20"},
{"smoothieware":"40"},
{"grbl":"10"},
{"unknown":"0"}]},
{"F":"system/system","P":"112","T":"I","V":"115200","H":"baud","O":[{"9600":"9600"},
{"19200":"19200"},
{"38400":"38400"},
{"57600":"57600"},
{"74880":"74880"},
{"115200":"115200"},
{"230400":"230400"},
{"250000":"250000"},
{"500000":"500000"},
{"921600":"921600"},
{"1000000":"1000000"},
{"1958400":"1958400"},
{"2000000":"2000000"},
]},
{"F":"system/boot","P":"320","T":"I","V":"100","H":"bootdelay","S":"40000","M":"0"},
{"F":"system/boot","P":"1023","T":"B","V":"0","H":"verbose","O":[{"no":"0"},{"yes":"1"}]},
{"F":"system/outputmsg","P":"129","T":"B","V":"1","H":"serial","O":[{"no":"0"},{"yes":"1"}]},
{"F":"system/outputmsg","P":"851","T":"B","V":"1","H":"M117","O":[{"no":"0"},{"yes":"1"}]},
{"F":"system/outputmsg","P":"1006","T":"B","V":"1","H":"telnet","O":[{"no":"0"},{"yes":"1"}]
}]}

1 - key : Settings
2 - value: array of data formated like this
{"F":"network/network","P":"130","T":"S","V":"esp3d","H":"hostname","S":"32","M":"1"}
or
{"F":"service/notification","P":"1004","T":"B","V":"1","H":"auto notif","O":[{"no":"0"},{"yes":"1"}]}

-   F: is filter formated as section/sub-section, if section is same as sub-section, it means no sub-section
-   P: is id (also position reference so it is unique)
-   T: is type of data which can be:
    -   S: for string
    -   I: for integer
    -   B: for Byte
    -   A: for IP address / Mask
    -   F: for float (only grblHAL)
    -   M: for bits mask (only grblHAL)
    -   X: for exclusive bitsfield (only grblHAL)
-   V: is current value, if type is string and value is `********`, (8 stars) then it is a password
-   E: is integer for exactess / precision of float/double value (only grblHAL)
-   U: is text unit of value (only grblHAL)
-   H: is text label of value
-   S: is max size if type is string, and max possible value if value is number (byte, integer)
-   M: is min size if type is string, and min possible value if value is number (byte, integer)
-   MS: is additionnal min size if type is string (e.g for password can be 0 or 8, so need additional min size), M should be the more minimal value
    so MS value must be between M and S
-   O: is an array of {label:value} used for possible values in selection or bits labels list
-   R: need restart to be applied

Note: if Type M and X use O entry to define the label / position, if O is [] then axis label are used according need X, Y, Z, A, B, C
Note2 : the 2.1 Flag type is no more used, several entries are used instead grouped by sub-section

If no json the list is limited to a list of <help>: <value>

Settings:
network/network/hostname: esp3d
network/network/radio mode: 5
network/network/radio_boot: 1
network/sta/SSID: NETWORK_SSID
network/sta/pwd: ********
network/sta/ip mode: 1
network/sta/ip: 192.168.0.254
network/sta/gw: 192.168.0.254
network/sta/msk: 255.255.255.0
network/sta/DNS: 192.168.0.254
network/sta/sta fallback mode: 5
network/ap/SSID: ESP3D
network/ap/pwd: ********
network/ap/ip: 192.168.0.1
network/ap/channel: 11
service/time/i-time: 0
service/time/tzone: +00:00
service/time/t-server: time.windows.com
service/time/t-server: time.google.com
service/time/t-server: 0.pool.ntp.org
service/notification/auto notif: 1
service/notification/notification: 0
service/notification/t1: 
service/notification/t2:
service/notification/ts: 
system/system/targetfw: 0
system/system/baud: 115200
system/boot/bootdelay: 10000
system/boot/verbose: 0
ok

+++ archetype = "section" title = "[ESP401]" weight = 800 +++ Set ESP3D settings

Input

[ESP401]<P=id> <T=type> <V=value> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
P
- P is the id or position in EEPROM of the setting to change
T * T is the type of the setting to change * T can be: - S: for string - I: for integer - B: for Byte - A: for IP address / Mask - F: for float (only grblHAL) - M: for bits mask (only grblHAL) - X: for exclusive bitsfield (only grblHAL)
V * V is the value to set if value has space add \`` in front of space to not be seen as separator e.g: [ESP401]P=1 T=S V=My\ SSID json`

Output

In json format

{
   "cmd":"401",
   "status":"ok",
   "data":"1"
}

cmd Id of requested command, should be 401
status status of command, should be ok
data content of response, here the id/position of the setting changed

+++ archetype = "section" title = "[ESP402]" weight = 800 +++ Get/Set SD updater check at boot time

Input

[ESP402]<state> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
state
- if state is empty, it will display current state
- if state is not empty, it will set the state ON, OFF

Output

In json format

{
   "cmd":"402",
   "status":"ok",
   "data":"OFF"
}

cmd Id of requested command, should be 402
status status of command, should be ok
data content of response, here the state

+++ archetype = "section" title = "[ESP410]" weight = 800 +++ List all AP detected around, if signal is too low, AP is not listed to avoid connection problems.

Input

[ESP410] json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"410",
   "status":"ok",
   "data":[
      {"SSID":"Luc-Lab","SIGNAL":"100","IS_PROTECTED":"1"},
      {"SSID":"CHT0573(Mesh)","SIGNAL":"100","IS_PROTECTED":"1"},
      {"SSID":"[LG_AirPurifier]","SIGNAL":"48","IS_PROTECTED":"1"},
   ]
}

cmd Id of requested command, should be 410
status status of command, should be ok
data content of response, here the list of AP detected with signal strength and if protected or not

plain text format

Start Scan
Luc-Lab 100%    Secure
CHT0573(Mesh)   100%    Secure
[LG_AirPurifier]    46%     Secure
End Scan

+++ archetype = "section" title = "[ESP420]" weight = 800 +++ Get ESP3D current status

Input

[ESP420] json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled

Output

{
   "cmd":"420",
   "status":"ok",
   "data":[
      {"id":"chip id","value":"11111"},
      {"id":"CPU Freq","value":"240Mhz"},
      {"id":"CPU Temp","value":"72.8C"},
      {"id":"free mem","value":"232.43 KB"},
      {"id":"SDK","value":"v4.4.4"},
      {"id":"flash size","value":"4.00 MB"},
      {"id":"FS type","value":"LittleFS"},
      {"id":"FS usage","value":"112.00 KB/128.00 KB"},
      {"id":"baud","value":"115200"},
      {"id":"sleep mode","value":"none"},
      {"id":"wifi","value":"ON"},
      {"id":"hostname","value":"esp3d"},
      {"id":"wifi mode","value":"ap"},
      {"id":"mac","value":"D4:D4:D4:D4:D4:D4"},
      {"id":"SSID","value":"ESP3D"},
      {"id":"visible","value":"yes"},
      {"id":"authentication","value":"WPA2"},
      {"id":"DHCP Server","value":"ON"},
      {"id":"ip","value":"192.168.0.1"},
      {"id":"gw","value":"192.168.0.1"},
      {"id":"msk","value":"255.255.255.0"},
      {"id":"clients","value":"0"},{"id":"sta","value":"OFF"},
      {"id":"mac","value":"D4:D4:D4:D4:D4:D4"},
      {"id":"ntp","value":"OFF"},
      {"id":"serial","value":"ON"},
      {"id":"notification","value":"ON (none)"},
      {"id":"targetfw","value":"unknown"},
      {"id":"FW ver","value":"3.0.0.a225"},
      {"id":"FW arch","value":"ESP32"}]}

cmd Id of requested command, should be 420
status status of command, should be ok
data content of response, where each status is a key/value pair of id/value

plain text format

Configuration:
chip id: 1010100
CPU Freq: 240Mhz
CPU Temp: 72.8C
free mem: 232.47 KB
SDK: v4.4.4
flash size: 4.00 MB
FS type: LittleFS
FS usage: 112.00 KB/128.00 KB
baud: 115200
sleep mode: none
wifi: ON
hostname: esp3d
wifi mode: ap
mac: D4:D4:D4:D4:D4:D4
SSID: ESP3D
visible: yes
authentication: WPA2
DHCP Server: ON
ip: 192.168.0.1
gw: 192.168.0.1
msk: 255.255.255.0
clients: 0
sta: OFF
mac: D4:D4:D4:D4:D4:D4
ntp: OFF
serial: ON
notification: ON (none)
targetfw: unknown
FW ver: 3.0.0.a225
FW arch: ESP32
ok

+++ archetype = "section" title = "[ESP444]" weight = 800 +++ Set ESP3D state

Input

[ESP444]<state> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
state
- RESET to reset all settings to default
- RESTART to restart ESP3D

Output

In json format

{
   "cmd":"444",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 444
status status of command, should be ok
data content of response, here ok

+++ archetype = "section" title = "[ESP450]" weight = 800 +++ List available ESP3D modules/ ESP3D related devices around

Input

[ESP450] json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"450",
   "status":"ok",
   "data":[
      {
         "Hostname":"esp3d-tft",
         "IP":"192.168.1.108",
         "port":"80",
         "TxT":[
            {"key":"version","value":"1.0.0.a18"},
            {"key":"firmware","value":"ESP3D-TFT"}
         ]
      }
   ]
}

cmd Id of requested command, should be 450
status status of command, should be ok
data content of response, here the list of modules detected with hostname, IP, port and TXT record

plain text format

Start Scan
esp3d-tft (192.168.1.108:80) version=1.0.0.a18,firmware=ESP3D-TFT
End Scan

+++ archetype = "section" title = "[ESP500]" weight = 800 +++ Get authentication status

Input

[ESP500] json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"500",
   "status":"ok",
   "data":"admin"
}

cmd Id of requested command, should be 500
status status of command, should be ok
data content of response, here the current user authenticated

plain text format

admin

+++ archetype = "section" title = "[ESP510]" weight = 800 +++ Set/display session time out

Input

[ESP510]<timeout> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
timeout
- if timeout is empty, it will display current timeout (0~255 minutes), 0 means disable timeout
- if timeout is not empty, it will set the timeout
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"510",
   "status":"ok",
   "data":"10"
}

cmd Id of requested command, should be 510
status status of command, should be ok
data content of response, here the current timeout

plain text format

+++ archetype = "section" title = "[ESP550]" weight = 800 +++ Set/Change admin password, only authenticated admin can change the password

Input

[ESP550]<password> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
password for the admin limited to 20 characters

Output

In json format

{
   "cmd":"550",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 550
status status of command, should be ok
data content of response, here ok when password is changed

+++ archetype = "section" title = "[ESP555]" weight = 800 +++ Set/Change user password, only authenticated admin/user can change the password

Input

[ESP555]<password> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
password for the user limited to 20 characters

Output

In json format

{
   "cmd":"555",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 555
status status of command, should be ok
data content of response, here ok when password is changed

+++ archetype = "section" title = "[ESP600]" weight = 800 +++ Send Notification using defined method, will also send notification to webui and eventually to any connected screen

Input

[ESP600]<message> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
message the message to send, limited to 128 characters. Message can contain some variables:
- %ESP_NAME% : ESP3D hostname
- %ESP_IP% : ESP3D local IP address

Output

In json format

{
   "cmd":"600",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 600
status status of command, should be ok
data content of response, here ok when notification is sent

+++ archetype = "section" title = "[ESP610]" weight = 800 +++ Set/Get Notification settings

Input

[ESP610]type=<NONE/PUSHOVER/EMAIL/LINE/IFTTT> T1=<token1> T2=<token2> TS=<Settings> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
type
- if type is empty, it will display current type
- if type is not empty, it will set the type currently only these types are supported:
  - NONE
  - PUSHOVER
  - EMAIL
  - LINE
  - TELEGRAM
  - IFTTT (by webhook)
  - HomeAssistant (via webhook)
T1
- if T1 is not empty, it will set the token1 which depend on type of notification
T2
- if T2 is not empty, it will set the token2 which depend on type of notification
TS if TS is not empty, it will set the setting token which depend on type of notification
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"610",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 610
status status of command, should be ok
data content of response, here ok when notification is sent

+++ archetype = "section" title = "[ESP620]" weight = 800 +++ Send Notification using encodded URL

Input

[ESP620]<url> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
url the url to send, limited to 128 characters, must be encoded

Output

In json format

{
   "cmd":"620",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 620
status status of command, should be ok
data content of response, here ok when notification is sent

+++ archetype = "section" title = "[ESP700]" weight = 800 +++ Process local file on /FS or /SD

Input

[ESP700]<filename> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
filename the filename to process, must be a valid file on /FS or /SD

Output

In json format

{
   "cmd":"700",
   "status":"ok",
   "data":"Processing <filename>"
}

cmd Id of requested command, should be 700
status status of command, should be ok
data content of response, here Processing <filename> when file is processing

+++ archetype = "section" title = "[ESP701]" weight = 800 +++ Query and Control ESP700 stream

Input

[ESP701]action=<action> <CLEAR_ERROR>json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
action
- if action is empty, it will display current state
- if action is not empty, it will set the action currently only these actions are supported:
  - ABORT
  - PAUSE
  - RESUME
CLEAR_ERROR
- if CLEAR_ERROR is present, it will clear the current error state

Output

In json format

{
   "cmd":"701",
   "status":"ok",
   "data":{
      "status":"processing",
      "total":"1000",
      "processed":"500",
      "type":"1",
      "name":"/SD/myfile.gco"
   }
}

cmd Id of requested command, should be 701
status status of command, should be ok
data content of response, here the current state of stream

+++ archetype = "section" title = "[ESP710]" weight = 800 +++ Format ESP Filesystem

Input

[ESP710]FORMATFS json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
FORMATFS
- if FORMATFS is present, it will format the local filesystem

Output

In json format

{
   "cmd":"710",
   "status":"ok",
   "data":"Starting formating..."
}

cmd Id of requested command, should be 710
status status of command, should be ok
data content of response, here Starting formating... when filesystem is starting

an new message is sent when formating is done

{
   "cmd":"710",
   "status":"ok",
   "data":"Formating done"
}

cmd Id of requested command, should be 710
status status of command, should be ok
data content of response, here Formating done when filesystem is done

+++ archetype = "section" title = "[ESP715]" weight = 800 +++ Format SD Card

Input

[ESP715]FORMATSD json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
FORMATSD
- if FORMATSD is present, it will format the SD card

Output

In json format

{
   "cmd":"715",
   "status":"ok",
   "data":"Starting formating..."
}

cmd Id of requested command, should be 715
status status of command, should be ok
data content of response, here Starting formating... when SD card is starting

an new message is sent when formating is done

{
   "cmd":"715",
   "status":"ok",
   "data":"Formating done"
}

cmd Id of requested command, should be 715
status status of command, should be ok
data content of response, here Formating done when SD card is done

+++ archetype = "section" title = "[ESP720]" weight = 800 +++ List files on /FS or defined repository

Input

[ESP720]<Root> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
Root
- if Root is empty, it will list files on /FS
- if Root is not empty, it will list files on defined repository

Output

json

{
   "cmd":"720",
   "status":"ok",
   "data":{
      "path":"/",
      "files":[
         {"name":"index.html.gz","size":"88.67 KB","time":"2023-11-05 11:57:57"}
      ], 
      "total":"128.00 KB",
      "used":"100.00 KB",
      "occupation":"78"
   }
}

cmd Id of requested command, should be 720
status status of command, should be ok
data content of response, here the list of files on /FS or defined repository
txt

Directory on Flash : /
         index.html.gz  88.67 KB        2023-11-05 11:57:57
Files: 1, Dirs :0
Total: 128.00 KB, Used: 100.00 KB, Available: 28.00 KB

+++ archetype = "section" title = "[ESP730]" weight = 800 +++ Do some actions on ESP Filesystem: rmdir / remove / mkdir / exists / create

Input

[ESP730]<action>=<path> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
action
- if action is not empty, it will set the action currently only these actions are supported:
  - RMDIR (dir)
  - REMOVE (file)
  - MKDIR (dir)
  - EXISTS (file/dir)
  - CREATE (file)
path the path to process, must be a valid file or directory on /FS

Output

In json format

{
   "cmd":"730",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 730
status status of command, should be ok
data content of response, here ok when action is done

+++ archetype = "section" title = "[ESP740]" weight = 800 +++ List files on /SD or defined repository

Input

[ESP740]<Root> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
Root
- if Root is empty, it will list files on /SD
- if Root is not empty, it will list files on defined repository

Output

json

{
   "cmd":"720",
   "status":"ok",
   "data":{
      "path":"/",
      "files":[
         {"name":"System Volume Information","size":"-1"},
         {"name":"src","size":"-1"},
         {"name":"testdir","size":"-1"},
         {"name":"Newfolder2","size":"-1"},
         {"name":"conventions","size":"-1"},
         {"name":"extensions","size":"-1"},
         {"name":"fileupload","size":"-1"},
         {"name":"realtimecmd","size":"-1"},
         {"name":"variableslist","size":"-1"},
         {"name":"webhandlers","size":"-1"},
         {"name":"websockets","size":"-1"},
         {"name":"main","size":"-1"},
         {"name":"mks_pft70.sys","size":"5 B"},
         {"name":"index.html","size":"57.47 KB"},
         {"name":"index.xml","size":"7.53 KB"},
         {"name":"index.print.html","size":"77.74 KB"}
      ], 
      "total":"7.20 GB",
      "used":"52.06 MB",
      "occupation":"1"
   }
}

cmd Id of requested command, should be 740
status status of command, should be ok
data content of response, here the list of files on /SD or defined repository
text
```
Directory on SD : /
```

[DIR] System Volume Information [DIR] src [DIR] testdir [DIR] New%20folder2 [DIR] conventions [DIR] extensions [DIR] fileupload [DIR] realtimecmd [DIR] variableslist [DIR] webhandlers [DIR] websockets [DIR] main mks_pft70.sys 5 B index.html 57.47 KB index.xml 7.53 KB index.print.html 77.74 KB Files: 4, Dirs :12 Total: 7.20 GB, Used: 52.06 MB, Available: 7.15 GB



+++
archetype = "section"
title = "[ESP750]"
weight = 800
+++
Do some actions on SD Card:  rmdir / remove / mkdir / exists / create

## Input
`[ESP750]<action>=<path> json=<no> pwd=<admin password>`

* json=no
the output format can be in JSON or plain text

* action
  * if action is not empty, it will set the action
  currently only these actions are supported:
    - RMDIR (dir)
    - REMOVE (file)
    - MKDIR (dir)
    - EXISTS (file/dir)
    - CREATE (file)
   

* path
   the path to process, must be a valid file or directory on /SD

## Output

- In json format

```json
{
   "cmd":"750",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 750
status status of command, should be ok
data content of response, here ok when action is done

+++ archetype = "section" title = "[ESP780]" weight = 800 +++ List Global Filesystem

Input

[ESP780]<Root> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
pwd= the admin password if authentication is enabled
Root
- if Root is empty, it will list files on /FS
- if Root is not empty, it will list files on defined repository

Output

json

{
   "cmd":"780",
   "status":"ok",
   "data":{
      "path":"/",
      "files":[
         {"name":"FS","size":"-1"},
         {"name":"SD","size":"-1"}
      ], 
      "total":"0 B",
      "used":"0 B",
      "occupation":"0"
   }
}

cmd Id of requested command, should be 780
status status of command, should be ok
data content of response, here the list of files on /FS or defined repository
text

Directory on Global FS : / [DIR] FS [DIR] SD Files: 0, Dirs :2 Total: 0 B, Used: 0 B, Available: 0 B


+++
archetype = "section"
title = "[ESP790]"
weight = 800
+++
Do some actions on Global Filesystem:  rmdir / remove / mkdir / exists / create

## Input
`[ESP790]<action>=<path> json=<no> pwd=<admin password>`

* json=no
the output format can be in JSON or plain text

* pwd=<admin password>
the admin password if authentication is enabled

* action
  * if action is not empty, it will set the action
  currently only these actions are supported:
    - RMDIR (dir)
    - REMOVE (file)
    - MKDIR (dir)
    - EXISTS (file/dir)
    - CREATE (file)


* path
   the path to process, must be a valid file or directory on /FS or /SD

## Output

- In json format

```json
{
   "cmd":"790",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 790
status status of command, should be ok
data content of response, here ok when action is done

+++ archetype = "section" title = "[ESP800]" weight = 800 +++ Get fw capabilities eventually set time with pc time and set setup state

Input

[ESP800]<time=YYYY-MM-DDTHH:mm:ss> <version=3.0.0-a11> <setup=0/1> json=<no> pwd=<admin password>

* json=yes
the output format
* time=
to set ESP3D time using ISO 8601 format : `YYYY`-`MM`-`DD`T`HH`:`minutes`:`seconds`
* tz=+08:00 (optional)
to set ESP3D time zone using ISO 8601 format : `+`/`-` `HH`-`minutes`
* version
version of webUI
* setup flag
Enable / Disable the setup flag

Output

In json format

{
   "cmd":"800",
   "status":"ok",
   "data":{
           "FWVersion":"bugfix-2.0.x-3.0.0.a200",
           "FWTarget":"marlin",
           "FWTargetID":"30",
           "Setup":"Enabled",
           "SDConnection":"shared",
           "SerialProtocol":"Socket",
           "Authentication":"Disabled",
           "WebCommunication":"Synchronous",
           "WebSocketIP":"192.168.2.117",
           "WebSocketPort":"81",
           "Hostname":"esp3d",
           "WiFiMode":"STA",
           "WebUpdate":"Enabled",
           "FlashFileSystem":"LittleFS",
           "HostPath":"www",
           "Time":"none"
           }
}

* `cmd`
Id of requested command, should be `800`

* `status`
status of command, should be `ok`

* `data`
content of response:
    * `FWVersion`
    Version  of ESP3D firmware or targeted FW (Marlin with ESP3DLib / grblHal)
    * `FWTarget`
    name of targeted  Firmware
    * `FWTargetID`
    numerical ID of targeted FW as same name can have several Ids
    * `Setup`
    Should be `Enabled` or `Disabled` according flag in EEPROM/Preferences, this allows to WedUI to start wizard automaticaly (or not)

    * `SDConnection`
    This is SD capability, SD can be
        * `shared`
        ESP does share access to SD card reader with main board or Firmware (Marlin with ESP3Dlib, ESP3D with hardware SD share solution)
        * `direct`
        ESP does have direct access to SD card reader (e.g: ESP3D, grblHal)
        * `none`
        ESP does not have direct access to SD card reader, (e.g: ESP3D with only serial connection)
    * `SerialProtocol`
    It define how ESP3D FW communicate with main FW
      * `Socket`
        ESP and main FW use same FW (e.g: Marlin with ESP3DLib, grblHal)
      * `Raw`
        Classic serial connection
      * `MKS`
        Serial connection using MKS protocol
    * `Authentication`
    Can be `Enabled` or `Disabled`
    * `WebCommunication`
      currently only `Synchronous`, because `Asychronous` has been put in hold
    * `WebSocketIP`
    Ip address for the websocket terminal `192.168.2.117`
    * `WebSocketPort`
    Port for the web socket terminal `81`
    * `Hostname`
     Hostname of ESP3D or main Baord `esp3d`
    * `WiFiMode`
    Current wiFi mode in use can be `AP` or `STA`
    * `WebUpdate`
    Inform webUI the feature is available or not, can be `Enabled` or `Disabled`
    * `FlashFileSystem` (currently `FileSystem`, to be updated soon )
    The file system used by ESP board can be `LittleFS`, `SPIFFS`, `Fat`, `none`
    * `HostPath`
    Path where the preferences.json and index.html.gz are stored and can be updated (e.g: `www`)
    * `Time`
    Type of time support
       * `none`
        Time is not supported
       * `Auto`
       Board use internet to sync time and it is successful
       * `Failed to set`
       Board use internet to sync time and it is failed
       * `Manual`
       Board use time of ESP800 to set the time and it is successful
        * `Not set`
       Board use time of ESP800 to set the time and command did not sent it (time may have been set by previous command)
    * `CameraID`
    if ESP has camera it contain the camera ID
    * `CameraName`
    if  ESP has camera it contain the camera name
    * `Axisletters`
    Currently only used for grbHAL
    can be :
      - XYZABC
      - XYZUVZ (supported soon)
      - XYZABCUVZ (supported soon)

+++ archetype = "section" title = "[ESP900]" weight = 800 +++ Get state / Set Serial Communication

Input

[ESP900]<state> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
state
- if state is empty, it will display current state
- if state is not empty, it will set the state currently only these states are supported:
  - ENABLE
  - DISABLE
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"900",
   "status":"ok",
   "data":"ENABLED"
}

cmd Id of requested command, should be 900
status status of command, should be ok
data content of response, here the current state

plain text format

ENABLED

+++ archetype = "section" title = "[ESP901]" weight = 800 +++ Set Serial baudrate for main serial communication

Input

[ESP901]<baudrate> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
baudrate
- if baudrate is empty, it will display current baudrate
- if baudrate is not empty, it will set the baudrate currently only these baudrates are supported:
  - 9600
  - 19200
  - 38400
  - 57600
  - 74880
  - 115200
  - 230400
  - 250000
  - 500000
  - 921600
  - 1000000
  - 1958400
  - 2000000
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"901",
   "status":"ok",
   "data":"115200"
}

cmd Id of requested command, should be 901
status status of command, should be ok
data content of response, here the current baudrate

plain text format

+++ archetype = "section" title = "[ESP910]" weight = 800 +++ Get state / Set Enable / Disable buzzer

Input

[ESP910]<state> json=<no> pwd=<admin password>

json=no the output format can be in JSON or plain text
state
- if state is empty, it will display current state
- if state is not empty, it will set the state currently only these states are supported:
  - ENABLE
  - DISABLE
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"910",
   "status":"ok",
   "data":"ENABLED"
}

cmd Id of requested command, should be 910
status status of command, should be ok
data content of response, here the current state

plain text format

ENABLED

+++ archetype = "section" title = "[ESP930]" weight = 800 +++ Set Bridge Serial state which can be ON, OFF, CLOSE

Input

[ESP930]<state> json=<no> pwd=<admin password>

json=no the output format
state
- if state is empty, it will display current state
- if state is not empty, it will set the state currently only these states are supported:
  - ENABLE
  - DISABLE
  - CLOSE
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"930",
   "status":"ok",
   "data":"ENABLED"
}

cmd Id of requested command, should be 930
status status of command, should be ok
data content of response, here the current state

plain text format

ENABLED

+++ archetype = "section" title = "[ESP931]" weight = 800 +++ Set Bridge Serial baudrate

Input

[ESP931]<baudrate> json=<no> pwd=<admin password>

json=no the output format
baudrate
- if baudrate is empty, it will display current baudrate
- if baudrate is not empty, it will set the baudrate currently only these baudrates are supported:
  - 9600
  - 19200
  - 38400
  - 57600
  - 74880
  - 115200
  - 230400
  - 250000
  - 500000
  - 921600
  - 1958400
pwd= the admin password if authentication is enabled

Output

In json format

{
   "cmd":"931",
   "status":"ok",
   "data":"115200"
}

cmd Id of requested command, should be 931
status status of command, should be ok
data content of response, here the current baudrate

plain text format

+++ archetype = "section" title = "[ESP999]" weight = 800 +++ Set quiet boot if strapping pin is High, can only e done o6nce and cannot be reverted

Input

[ESP999]QUIETBOOT json=<no> pwd=<admin password>

json=no the output format
pwd= the admin password if authentication is enabled
QUIETBOOT
- if QUIETBOOT is present, it will set the quiet boot flag

Output

In json format

{
   "cmd":"999",
   "status":"ok",
   "data":"ok"
}

cmd Id of requested command, should be 999
status status of command, should be ok
data content of response, here ok when quiet boot is set

plain text format

ok

Files

espXXX.md

Latest commit

History

espXXX.md

File metadata and controls

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input

Output

Input