Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Jump to bottom

e900v22c 5.15内核安装进emmc后不能启动 #222

Closed
LomotHo opened this issue Apr 4, 2022 · 9 comments
Closed

e900v22c 5.15内核安装进emmc后不能启动 #222

LomotHo opened this issue Apr 4, 2022 · 9 comments
Labels
support This need is supported

Comments

@LomotHo
Copy link

LomotHo commented Apr 4, 2022 •
edited
Loading

版本: Armbian_22.05.0_Aml_s905l3a_focal_5.15.32_2022.03.30.1638

以下为开机串口日志

G12A:BL:0253b8:61aa2d;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
                                                                       bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:00000703
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f83180

TE: 88060

BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz

Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe

LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

soc_vref_reg_value 0x 00000024 00000025 00000025 00000025 00000026 00000026 00000028 00000027 00000025 00000025 00000026 00000025 00000026 00000025 00000026 00000028 00000026 00000027 00000027 00000027 00000027 00000027 00000027 00000027 00000027 00000027 00000025 00000028 00000028 00000027 00000024 00000026 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
 dram_vref_reg_value 0x 0000005f
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 457
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d6a00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0c 70 00 01 35 1e 00 00 0d 37 39 38 4e 43 50
[0.014262 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE:  BL31: v1.3(release):9d705ef56-dirty
NOTICE:  BL31: Built : 19:18:02, Jul 28 2021
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 26 2021 - 14:35:31)

DRAM:  2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f3be68
gpio: pin GPIOAO_9 (gpio 9) value is 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x0000000073e35d90
aml_priv->desc_buf = 0x0000000073e380d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 282: PART_TYPE_DOS
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073e3a920,dt_addr=0000000073e3a920
get_partition_from_dts() 92: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 21
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:     skmac   0000000000400000 1
13:       odm   0000000001000000 1
14:    system   0000000050000000 1
15:   product   0000000008000000 1
16:       ctc   0000000010000000 1
17:   skparam   0000000001000000 2
18:  skbackup   0000000030000000 2
19:     cache   0000000040000000 2
20:      data   ffffffffffffffff 4
init_part() 282: PART_TYPE_DOS
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc b03be973, store b03be973
_verify_dtb_checksum()-3476: calc b03be973, store b03be973
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 637
aml_config_dtb 667
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = <0x02faf080>
status = "disabled"
status = "okay"
wipe_data=successful
wipe_cache=successful
upgrade_step=0
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
** Invalid partition 14 **
Err imgread(L815):Fail in load logo cmd
logo part bootup
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
Err imgread(L574):Logo header err.
There is no valid bmp file at the given address
[OSD]osd_hw.free_dst_data: 0,1279,0,719
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[720p50hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 19
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 3  vid_clk_div = 1
hdmitx: set enc for VIC: 19
hdmitx phy setting done
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmi_tx_set: save mode: 720p50hz, attr: 444,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
time_out = 493e0
key[0] = 66994cb3
key[1] = 6699fd01
key[2] = 6699dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
time_out = 0
key[0] = 3ec14cb3
key[1] = 3ec1fd01
key[2] = 3ec1dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
get bootloader message from misc partition:
[commannd:bootonce-bootloader]
[status:]
[recovery:]
command mark(uboot-command) not match bootonce-bootloader,don't execute.
InUsbBurn
wait for phy ready count is 0
noSof
sof timeout, reset usb phy tuning
rebootmode=cold_boot
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
pll tsensor avg: 0x1ea7, u_efuse: 0x8026
temp1: 27
ddr tsensor avg: 0x1e9f, u_efuse: 0x800d
temp2: 27
device cool done
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
CONFIG_AVB2: null
active_slot: normal
avb2: 0
ee_gate_off ...
avb2: 0
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 buildvariant=userdebug
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
   Loading Kernel Image(COMP_NONE) ... OK
   kernel loaded at 0x01080000, end = 0x01c0e860
   Loading Ramdisk to 09e94000, end 09fff235 ... OK
   Loading Device Tree to 0000000009e7d000, end 0000000009e93cda ... OK
fdt_fixup_memory_banks, reg:0000000000000000

Starting kernel ...

uboot time: 3479305 us
[    0.000000@0]        07400000 - 07500000,     1024 KB, ramoops@0x07400000
[    0.000000@0]        05000000 - 05400000,     4096 KB, linux,secmon
[    0.000000@0]        7f800000 - 80000000,     8192 KB, linux,meson-fb
[    0.000000@0]        77800000 - 7f800000,   131072 KB, linux,ion-dev
[    0.000000@0]        73400000 - 77800000,    69632 KB, linux,di_cma
[    0.000000@0]        5a400000 - 73400000,   409600 KB, linux,codec_mm_cma
[    0.000000@0]        5a400000 - 5a400000,        0 KB, linux,codec_mm_reserved
[    0.000000@0]        56400000 - 5a400000,    65536 KB, linux,vdin0_cma
[    0.000000@0]        52400000 - 56400000,    65536 KB, linux,vdin1_cma
[    1.328494@2] pgd = d7320000
[    1.328516@2] [00000014] *pgd=51428835
[    1.434536@0] reboot: Restarting system with command 'bootloader'
bl31 reboot reason: 0xd
bl31 reboot reason: 0x7
system cmd  1.
G12A:BL:0253b8:61aa2d;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
                                                                       bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:00000703
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f83180

TE: 83597

BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz

Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe

LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

soc_vref_reg_value 0x 00000025 00000025 00000025 00000025 00000026 00000026 00000028 00000027 00000025 00000024 00000026 00000025 00000026 00000025 00000026 00000028 00000026 00000027 00000027 00000026 00000027 00000026 00000027 00000027 00000027 00000027 00000025 00000028 00000028 00000026 00000024 00000026 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
 dram_vref_reg_value 0x 0000005f
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 457
result report
boot times 1Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d6a00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0c 70 00 01 35 1e 00 00 0d 37 39 38 4e 43 50
[0.792662 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE:  BL31: v1.3(release):9d705ef56-dirty
NOTICE:  BL31: Built : 19:18:02, Jul 28 2021
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 26 2021 - 14:35:31)

DRAM:  2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f3be68
gpio: pin GPIOAO_9 (gpio 9) value is 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x0000000073e35d90
aml_priv->desc_buf = 0x0000000073e380d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 282: PART_TYPE_DOS
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073e3a920,dt_addr=0000000073e3a920
get_partition_from_dts() 92: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 21
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:     skmac   0000000000400000 1
13:       odm   0000000001000000 1
14:    system   0000000050000000 1
15:   product   0000000008000000 1
16:       ctc   0000000010000000 1
17:   skparam   0000000001000000 2
18:  skbackup   0000000030000000 2
19:     cache   0000000040000000 2
20:      data   ffffffffffffffff 4
init_part() 282: PART_TYPE_DOS
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=bootloader
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc b03be973, store b03be973
_verify_dtb_checksum()-3476: calc b03be973, store b03be973
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 637
aml_config_dtb 667
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = <0x02faf080>
status = "disabled"
status = "okay"
wipe_data=successful
wipe_cache=successful
upgrade_step=0
reboot_mode:::: bootloader
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
** Invalid partition 14 **
Err imgread(L815):Fail in load logo cmd
logo part bootup
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
Err imgread(L574):Logo header err.
There is no valid bmp file at the given address
[OSD]osd_hw.free_dst_data: 0,1279,0,719
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[720p50hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 19
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 3  vid_clk_div = 1
hdmitx: set enc for VIC: 19
hdmitx phy setting done
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmi_tx_set: save mode: 720p50hz, attr: 444,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
time_out = 493e0
key[0] = 66994cb3
key[1] = 6699fd01
key[2] = 6699dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
time_out = 0
key[0] = 3ec14cb3
key[1] = 3ec1fd01
key[2] = 3ec1dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
get bootloader message from misc partition:
[commannd:bootonce-bootloader]
[status:]
[recovery:]
command mark(uboot-command) not match bootonce-bootloader,don't execute.
rebootmode=bootloader
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
g12a_u212_v1#
@LomotHo
Copy link
Author

LomotHo commented Apr 4, 2022

usb可以正常启动, 下面是usb启动的日志

G12A:BL:0253b8:61aa2d;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;CHK:1F;READ:0;0.0;
                                                                                     bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:00000703
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f83180

TE: 140294

BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz

Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 1
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 1
fw parse done
PIEI prepare done
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe

LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz
00000000
emmc switch 1 ok

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

soc_vref_reg_value 0x 00000024 00000024 00000025 00000024 00000026 00000026 00000027 00000026 00000025 00000024 00000025 00000024 00000025 00000025 00000025 00000027 00000027 00000027 00000027 00000027 00000028 00000027 00000028 00000027 00000028 00000028 00000026 00000029 00000029 00000027 00000024 00000027 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
 dram_vref_reg_value 0x 0000005f
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 462
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 1 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 1
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d6a00, part: 1
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0c 70 00 01 35 1e 00 00 0d 37 39 38 4e 43 50
[0.014271 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE:  BL31: v1.3(release):9d705ef56-dirty
NOTICE:  BL31: Built : 19:18:02, Jul 28 2021
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 26 2021 - 14:35:31)

DRAM:  2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f3be68
gpio: pin GPIOAO_9 (gpio 9) value is 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x0000000073e35d90
aml_priv->desc_buf = 0x0000000073e380d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073e3a920,dt_addr=0000000073e3a920
get_partition_from_dts() 92: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 21
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:     skmac   0000000000400000 1
13:       odm   0000000001000000 1
14:    system   0000000050000000 1
15:   product   0000000008000000 1
16:       ctc   0000000010000000 1
17:   skparam   0000000001000000 2
18:  skbackup   0000000030000000 2
19:     cache   0000000040000000 2
20:      data   ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc b03be973, store b03be973
_verify_dtb_checksum()-3476: calc b03be973, store b03be973
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 637
aml_config_dtb 667
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = <0x02faf080>
status = "disabled"
status = "okay"
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
6220856 bytes read in 189 ms (31.4 MiB/s)
[imgread]load bmp from ext4 part okay
bmp pixel: 24
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,1279,0,719
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[720p50hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 19
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 3  vid_clk_div = 1
hdmitx: set enc for VIC: 19
hdmitx phy setting done
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmi_tx_set: save mode: 720p50hz, attr: 444,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
time_out = 493e0
key[0] = 66994cb3
key[1] = 6699fd01
key[2] = 6699dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
time_out = 0
key[0] = 3ec14cb3
key[1] = 3ec1fd01
key[2] = 3ec1dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
get bootloader message from misc partition:
[commannd:bootonce-bootloader]
[status:]
[recovery:]
command mark(uboot-command) not match bootonce-bootloader,don't execute.
InUsbBurn
wait for phy ready count is 0
noSof
sof timeout, reset usb phy tuning
rebootmode=cold_boot
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
card out
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 3000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... Device not responding to set address.
Setup ERROR: address device command for slot 1.
retry new usb device
2 USB Device(s) found
       scanning usb for storage devices... init_part() 282: PART_TYPE_DOS
1 Storage Device(s) found
reading s905_autoscript
1654 bytes read in 32 ms (49.8 KiB/s)
## Executing script at 01020000
start amlogic old u-boot
## Error: "bootfromsd" not defined
card out
** Bad device mmc 0 **
reading boot_android
** Unable to read file boot_android **
card out
** Bad device mmc 0 **
reading u-boot.ext
694755 bytes read in 78 ms (8.5 MiB/s)
## Starting application at 0x01000000 ...


U-Boot 2021.04-00056-g13ac02db31-dirty (Apr 28 2021 - 22:44:20 +0800) u200

Model: Amlogic Meson G12A U200 Development Board
SoC:   Amlogic Meson G12A (Unknown) Revision 28:c (70:2)
DRAM:  2 GiB
MMC:   sd@ffe05000: 0, mmc@ffe07000: 1
Loading Environment from nowhere... OK
In:    serial@3000
Out:   serial@3000
Err:   serial@3000
Net:   eth0: ethernet@ff3f0000
Hit any key to stop autoboot:  0
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: Kingston Rev:  Prod: DataTraveler 3.0
            Type: Removable Hard Disk
            Capacity: 29510.4 MB = 28.8 GB (60437492 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1123 bytes read in 1 ms (1.1 MiB/s)
## Executing script at 08000000
Start AMLOGIC mainline U-boot
## Error: "bootfromsd" not defined
352 bytes read in 1 ms (343.8 KiB/s)
## Error: "mac" not defined
## Error: "eth_mac" not defined
ethaddr=e2:50:95:c8:0a:5a
25848320 bytes read in 875 ms (28.2 MiB/s)
11449952 bytes read in 377 ms (29 MiB/s)
72049 bytes read in 5 ms (13.7 MiB/s)
Moving Image from 0x8080000 to 0x8200000, end=9b90000
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    11449888 Bytes = 10.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 08008000
   Booting using the fdt blob at 0x8008000
   Loading Ramdisk to 3f514000, end 3ffff620 ... OK
   Loading Device Tree to 000000003f4ff000, end 000000003f513970 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.15.32-flippy-71+ (root@univm25) (Ubuntu clang version 14.0.0-+rc4-1ubuntu1, Ubuntu LLD 14.0.0) #93 SMP PREEMPT Mon Mar 28 16:31:08 CST 2022
[    0.000000] Machine model: Amlogic Meson G12A U200 Development Board
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000004ffffff]
[    0.000000]   node   0: [mem 0x0000000005000000-0x00000000072fffff]
[    0.000000]   node   0: [mem 0x0000000007300000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 19 pages/cpu s37528 r8192 d32104 u77824
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516096
[    0.000000] Kernel command line: root=UUID=454a7e77-73c3-4a4f-8e08-89cc469131fb rootflags=data=writeback rw rootfstype=ext4 console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 mac=e2:50:95:c8:0a:5a
[    0.000000] Unknown kernel command line parameters "cgroup_enable=memory cgroup_memory=1 mac=e2:50:95:c8:0a:5a", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1725152K/2097152K available (14720K kernel code, 2650K rwdata, 5724K rodata, 2048K init, 880K bss, 109856K reserved, 262144K cma-reserved)
[    0.000000] random: get_random_u64 called from kmem_cache_open+0x28/0x53c with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000246] Console: colour dummy device 80x25
[    0.000657] printk: console [tty0] enabled
[    0.000713] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.000739] pid_max: default: 32768 minimum: 301
[    0.000828] LSM: Security Framework initializing
[    0.000903] SELinux:  Initializing.
[    0.001023] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.001049] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.002744] rcu: Hierarchical SRCU implementation.
[    0.004123] EFI services will not be available.
[    0.004467] smp: Bringing up secondary CPUs ...
[    0.005043] Detected VIPT I-cache on CPU1
[    0.005105] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.005701] Detected VIPT I-cache on CPU2
[    0.005734] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.006294] Detected VIPT I-cache on CPU3
[    0.006321] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.006389] smp: Brought up 1 node, 4 CPUs
[    0.006452] SMP: Total of 4 processors activated.
[    0.006464] CPU features: detected: 32-bit EL0 Support
[    0.006474] CPU features: detected: 32-bit EL1 Support
[    0.006487] CPU features: detected: CRC32 instructions
[    0.007324] CPU: All CPU(s) started at EL2
[    0.007354] alternatives: patching kernel code
[    0.009276] devtmpfs: initialized
[    0.021683] Registered cp15_barrier emulation handler
[    0.021724] Registered setend emulation handler
[    0.021852] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.021882] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.031831] prandom: seed boundary self test passed
[    0.033087] prandom: 100 self tests passed
[    0.056067] prandom32: self test passed (less than 6 bits correlated)
[    0.056121] pinctrl core: initialized pinctrl subsystem
[    0.056767] DMI not present or invalid.
[    0.057054] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.058845] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.059013] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.059216] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.059332] audit: initializing netlink subsys (disabled)
[    0.059513] audit: type=2000 audit(0.056:1): state=initialized audit_enabled=0 res=1
[    0.060775] thermal_sys: Registered thermal governor 'step_wise'
[    0.061306] cpuidle: using governor ladder
[    0.061474] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.061584] ASID allocator initialised with 65536 entries
[    0.061705] Serial: AMBA PL011 UART driver
[    0.085332] platform ff900000.vpu: Fixing up cyclic dependency with ff600000.hdmi-tx
[    0.092837] platform cvbs-connector: Fixing up cyclic dependency with ff900000.vpu
[    0.093816] platform hdmi-connector: Fixing up cyclic dependency with ff600000.hdmi-tx
[    0.104807] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.104842] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.104857] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.104871] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    1.508462] cryptd: max_cpu_qlen set to 1000
[    1.511873] "cryptomgr_test" (94) uses obsolete ecb(arc4) skcipher
[    1.522957] alg: No test for 842 (842-generic)
[    1.523083] alg: No test for 842 (842-scomp)
[    1.613057] DRBG: Continuing without Jitter RNG
[    1.695798] raid6: neonx8   gen()  2224 MB/s
[    1.752537] raid6: neonx8   xor()  1604 MB/s
[    1.809284] raid6: neonx4   gen()  2209 MB/s
[    1.866022] raid6: neonx4   xor()  1538 MB/s
[    1.922774] raid6: neonx2   gen()  2027 MB/s
[    1.979511] raid6: neonx2   xor()  1435 MB/s
[    2.036269] raid6: neonx1   gen()  1664 MB/s
[    2.093006] raid6: neonx1   xor()  1177 MB/s
[    2.149742] raid6: int64x8  gen()  1506 MB/s
[    2.206487] raid6: int64x8  xor()   802 MB/s
[    2.263221] raid6: int64x4  gen()  1618 MB/s
[    2.319955] raid6: int64x4  xor()   823 MB/s
[    2.376725] raid6: int64x2  gen()  1386 MB/s
[    2.433433] raid6: int64x2  xor()   740 MB/s
[    2.490183] raid6: int64x1  gen()  1164 MB/s
[    2.546908] raid6: int64x1  xor()   582 MB/s
[    2.546920] raid6: using algorithm neonx8 gen() 2224 MB/s
[    2.546932] raid6: .... xor() 1604 MB/s, rmw enabled
[    2.546944] raid6: using neon recovery algorithm
[    2.547100] fbcon: Taking over console
[    2.548586] VDDAO_3V3: supplied by 12V
[    2.548961] iommu: Default domain type: Translated
[    2.548975] iommu: DMA domain TLB invalidation policy: strict mode
[    2.549308] vgaarb: loaded
[    2.549737] SCSI subsystem initialized
[    2.549953] usbcore: registered new interface driver usbfs
[    2.550001] usbcore: registered new interface driver hub
[    2.550053] usbcore: registered new device driver usb
[    2.550445] mc: Linux media interface: v0.10
[    2.550483] videodev: Linux video capture interface: v2.00
[    2.550731] EDAC MC: Ver: 3.0.0
[    2.551704] Advanced Linux Sound Architecture Driver Initialized.
[    2.552736] clocksource: Switched to clocksource arch_sys_counter
[    2.552984] VFS: Disk quotas dquot_6.6.0
[    2.553046] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    2.553183] FS-Cache: Loaded
[    2.560184] NET: Registered PF_INET protocol family
[    2.560358] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    2.561504] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    2.561549] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    2.561732] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[    2.561965] TCP: Hash tables configured (established 16384 bind 16384)
[    2.562149] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear)
[    2.562228] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    2.562283] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    2.562450] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    2.562489] NET: Registered PF_XDP protocol family
[    2.562510] PCI: CLS 0 bytes, default 64
[    2.562789] Trying to unpack rootfs image as initramfs...
[    2.570128] kvm [1]: IPA Size Limit: 40 bits
[    2.571154] kvm [1]: vgic interrupt IRQ9
[    2.571299] kvm [1]: Hyp mode initialized successfully
[    3.060526] Freeing initrd memory: 11180K
[    3.228985] Initialise system trusted keyrings
[    3.229160] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[    3.235764] zbud: loaded
[    3.237645] fuse: init (API version 7.34)
[    3.238069] SGI XFS with ACLs, security attributes, quota, no debug enabled
[    3.277495] NET: Registered PF_ALG protocol family
[    3.327820] xor: measuring software checksum speed
[    3.332647]    8regs           :  2051 MB/sec
[    3.336051]    32regs          :  2908 MB/sec
[    3.340667]    arm64_neon      :  2155 MB/sec
[    3.340680] xor: using function: 32regs (2908 MB/sec)
[    3.340697] Key type asymmetric registered
[    3.340708] Asymmetric key parser 'x509' registered
[    3.340796] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    3.340913] io scheduler mq-deadline registered
[    3.340927] io scheduler kyber registered
[    3.341063] io scheduler bfq registered
[    3.404510] soc soc0: Amlogic Meson G12A (Unknown) Revision 28:c (70:2) Detected
[    3.405902] VDDCPU: supplied by 12V
[    3.407312] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    3.409002] Serial: AMBA driver
[    3.409378] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 22, base_baud = 1500000) is a meson_uart
[    4.405828] printk: console [ttyAML0] enabled
[    4.418396] brd: module loaded
[    4.422142] loop: module loaded
[    4.429038] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.429971] ehci-pci: EHCI PCI platform driver
[    4.434399] ehci-platform: EHCI generic platform driver
[    4.439992] usbcore: registered new interface driver cdc_wdm
[    4.445171] usbcore: registered new interface driver usb-storage
[    4.451532] mousedev: PS/2 mouse device common for all mice
[    4.457492] SPI driver rmi4_spi has no spi_device_id for syna,rmi4-spi
[    4.463739] meson-vrtc ff8000a8.rtc: registered as rtc0
[    4.468264] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:04 UTC (4)
[    4.476673] i2c_dev: i2c /dev entries driver
[    4.484021] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present!
[    4.488426] Registered IR keymap rc-cec
[    4.491990] rc rc0: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc0
[    4.500648] input: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc0/input0
[    4.517865] Synopsys Designware Multimedia Card Interface Driver
[    4.519056] meson-gx-mmc ffe05000.sd: Got CD GPIO
[    4.519910] meson-sm: secure-monitor enabled
[    4.528361] hid: raw HID events driver (C) Jiri Kosina
[    4.532310] usbcore: registered new interface driver usbhid
[    4.537740] usbhid: USB HID core driver
[    4.544899] Initializing XFRM netlink socket
[    4.546121] NET: Registered PF_INET6 protocol family
[    4.552069] gpio irq setup: hwirq: 0x3B irqfirst: 0x35 irqlast: 0x3C pin[47]
[    4.557882] genirq: Setting trigger mode 3 for irq 36 failed (meson_gpio_irq_set_type+0x0/0x140)
[    4.576095] Segment Routing with IPv6
[    4.576135] RPL Segment Routing with IPv6
[    4.578143] In-situ OAM (IOAM) with IPv6
[    4.584551] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.591625] bpfilter: Loaded bpfilter_umh pid 299
[    4.592561] NET: Registered PF_PACKET protocol family
[    4.597601] NET: Registered PF_KEY protocol family
[    4.602409] 8021q: 802.1Q VLAN Support v1.8
[    4.606710] registered taskstats version 1
[    4.610473] Loading compiled-in X.509 certificates
[    4.616915] zswap: loaded using pool zstd/zbud
[    4.619990] Key type ._fscrypt registered
[    4.623582] Key type .fscrypt registered
[    4.627459] Key type fscrypt-provisioning registered
[    4.632992] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
[    4.658950] VCC_3V3: supplied by VDDAO_3V3
[    4.659472] VCC_5V: supplied by 12V
[    4.661021] VDDAO_1V8: supplied by VDDAO_3V3
[    4.741109] meson-drm ff900000.vpu: Queued 3 outputs on vpu
[    4.766111] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
[    4.770750] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver
[    4.778674] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops)
[    4.786086] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 0
[    4.815813] Console: switching to colour frame buffer device 90x36
[    4.840266] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device
[    4.850179] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[    4.853912] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[    4.860195] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[    4.866851] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[    4.873108] meson8b-dwmac ff3f0000.ethernet:         DWMAC1000
[    4.878234] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported
[    4.885640] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported
[    4.893068] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[    4.898236] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[    4.905221] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[    4.911600] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[    4.917472] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[    4.923242] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    4.933509] FLASH_1V8: supplied by VCC_3V3
[    4.935646] USB_PWR_EN: supplied by VCC_5V
[    4.939468] VCC_1V8: supplied by VCC_3V3
[    4.950884] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[    4.952803] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[    4.960884] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator
[    4.964710] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator
[    4.971856] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[    4.980047] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    4.984254] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 1
[    4.991818] xhci-hcd xhci-hcd.3.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010
[    5.001074] xhci-hcd xhci-hcd.3.auto: irq 39, io mem 0xff500000
[    5.007152] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[    5.015057] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.022219] usb usb1: Product: xHCI Host Controller
[    5.027045] usb usb1: Manufacturer: Linux 5.15.32-flippy-71+ xhci-hcd
[    5.033427] usb usb1: SerialNumber: xhci-hcd.3.auto
[    5.038604] hub 1-0:1.0: USB hub found
[    5.041988] hub 1-0:1.0: 2 ports detected
[    5.046210] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.051468] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 2
[    5.058969] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[    5.065466] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.073606] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15
[    5.081645] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.088800] usb usb2: Product: xHCI Host Controller
[    5.093630] usb usb2: Manufacturer: Linux 5.15.32-flippy-71+ xhci-hcd
[    5.100015] usb usb2: SerialNumber: xhci-hcd.3.auto
[    5.105125] hub 2-0:1.0: USB hub found
[    5.108578] hub 2-0:1.0: 1 port detected
[    5.114738] ALSA device list:
[    5.114842] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[    5.116611]   No soundcards found.
[    5.150426] Freeing unused kernel memory: 2048K
[    5.152544] Run /init as init process
[    5.238896] mmc2: new HS200 MMC card at address 0001
[    5.241783] mmcblk2: mmc2:0001 SPeMMC 7.22 GiB
[    5.247179] mmcblk2boot0: mmc2:0001 SPeMMC 4.00 MiB
[    5.250977] mmcblk2boot1: mmc2:0001 SPeMMC 4.00 MiB
[    5.255645] mmcblk2rpmb: mmc2:0001 SPeMMC 4.00 MiB, chardev (240:0)
[    5.282454] random: fast init done
[    5.429436] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[    5.578837] usb 1-2: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[    5.584870] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.592061] usb 1-2: Product: DataTraveler 3.0
[    5.596454] usb 1-2: Manufacturer: Kingston
[    5.600455] usb 1-2: SerialNumber: E0D55EA573F8F44018680554
[    5.607741] usb-storage 1-2:1.0: USB Mass Storage device detected
[    5.612411] scsi host0: usb-storage 1-2:1.0
[    6.624128] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 3.0      PQ: 0 ANSI: 6
[    6.654524] sd 0:0:0:0: [sda] 60437492 512-byte logical blocks: (30.9 GB/28.8 GiB)
[    6.660036] sd 0:0:0:0: [sda] Write Protect is off
[    6.664795] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    6.685269]  sda: sda1 sda2
[    6.694402] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    7.122958] EXT4-fs (sda2): mounted filesystem with writeback data mode. Opts: data=writeback. Quota mode: none.
[    7.807597] systemd[1]: System time before build time, advancing clock.
[    7.968120] systemd[1]: systemd 245.4-4ubuntu3.15 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    8.008639] systemd[1]: Detected architecture arm64.
[    8.077622] systemd[1]: Set hostname to <armbian>.
[    8.975831] random: systemd: uninitialized urandom read (16 bytes read)
[    8.981960] systemd[1]: Created slice system-modprobe.slice.
[    8.987196] random: systemd: uninitialized urandom read (16 bytes read)
[    8.992480] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    9.000222] random: systemd: uninitialized urandom read (16 bytes read)
[    9.005169] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    9.013783] systemd[1]: Created slice User and Session Slice.
[    9.018329] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[    9.030166] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    9.040369] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    9.050949] systemd[1]: Reached target Local Encrypted Volumes.
[    9.056775] systemd[1]: Reached target Slices.
[    9.061264] systemd[1]: Reached target Swap.
[    9.065653] systemd[1]: Reached target System Time Set.
[    9.084474] systemd[1]: Listening on RPCbind Server Activation Socket.
[    9.090660] systemd[1]: Listening on Syslog Socket.
[    9.095636] systemd[1]: Listening on fsck to fsckd communication Socket.
[    9.101629] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    9.108694] systemd[1]: Listening on Journal Audit Socket.
[    9.113777] systemd[1]: Listening on Journal Socket (/dev/log).
[    9.119724] systemd[1]: Listening on Journal Socket.
[    9.124817] systemd[1]: Listening on udev Control Socket.
[    9.129766] systemd[1]: Listening on udev Kernel Socket.
[    9.138105] systemd[1]: Mounting Huge Pages File System...
[    9.146562] systemd[1]: Mounting POSIX Message Queue File System...
[    9.155239] systemd[1]: Mounting NFSD configuration filesystem...
[    9.163954] systemd[1]: Mounting RPC Pipe File System...
[    9.173160] systemd[1]: Mounting Kernel Debug File System...
[    9.178000] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[    9.185224] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[    9.196237] RPC: Registered named UNIX socket transport module.
[    9.198987] systemd[1]: Starting Restore / save the current clock...
[    9.199882] RPC: Registered udp transport module.
[    9.199888] RPC: Registered tcp transport module.
[    9.199890] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.228372] systemd[1]: Starting Set the console keyboard layout...
[    9.237296] systemd[1]: Starting Create list of static device nodes for the current kernel...
[    9.246959] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
[    9.257394] systemd[1]: Started Nameserver information manager.
[    9.262790] systemd[1]: Reached target Network (Pre).
[    9.266635] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    9.273891] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[    9.287530] systemd[1]: Starting Load Kernel Modules...
[    9.296547] systemd[1]: Starting Remount Root and Kernel File Systems...
[    9.306041] systemd[1]: Starting udev Coldplug all Devices...
[    9.316998] systemd[1]: Mounted Huge Pages File System.
[    9.322804] systemd[1]: Mounted POSIX Message Queue File System.
[    9.327143] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro. Quota mode: none.
[    9.336835] systemd[1]: Mounted NFSD configuration filesystem.
[    9.342615] systemd[1]: Mounted RPC Pipe File System.
[    9.348064] systemd[1]: Mounted Kernel Debug File System.
[    9.355315] systemd[1]: Finished Restore / save the current clock.
[    9.363098] systemd[1]: Finished Create list of static device nodes for the current kernel.
[    9.379221] systemd[1]: Finished Load Kernel Modules.
[    9.387096] systemd[1]: Finished Remount Root and Kernel File Systems.
[    9.397977] systemd[1]: Mounting FUSE Control File System...
[    9.406455] systemd[1]: Mounting Kernel Configuration File System...
[    9.415347] systemd[1]: Starting pNFS block layout mapping daemon...
[    9.422961] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[    9.430575] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[    9.443185] systemd[1]: Starting Load/Save Random Seed...
[    9.451888] systemd[1]: Starting Apply Kernel Variables...
[    9.460724] systemd[1]: Starting Create System Users...
[    9.472059] systemd[1]: Mounted FUSE Control File System.
[    9.478084] systemd[1]: Mounted Kernel Configuration File System.
[    9.484580] systemd[1]: Started pNFS block layout mapping daemon.
[    9.511296] systemd[1]: Finished Set the console keyboard layout.
[    9.521088] systemd[1]: Finished Create System Users.
[    9.529990] systemd[1]: Starting Create Static Device Nodes in /dev...
[    9.546887] systemd[1]: Finished Apply Kernel Variables.
[    9.573186] systemd[1]: Finished Create Static Device Nodes in /dev.
[    9.579222] systemd[1]: Reached target Local File Systems (Pre).
[    9.588624] systemd[1]: Mounting /var/tmp...
[    9.597700] systemd[1]: Starting udev Kernel Device Manager...
[    9.605997] systemd[1]: Mounted /var/tmp.
[    9.649830] systemd[1]: Finished udev Coldplug all Devices.
[    9.661986] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
[    9.716547] systemd[1]: Started udev Kernel Device Manager.
[    9.872582] random: crng init done
[    9.874667] random: 7 urandom warning(s) missed due to ratelimiting
[    9.931373] systemd[1]: Finished Load/Save Random Seed.
[    9.987651] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[   10.009672] Registered IR keymap rc-empty
[   10.013117] rc rc1: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1
[   10.018194] rc rc1: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[   10.037417] systemd[1]: Found device /dev/ttyAML0.
[   10.041174] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1/input1
[   10.050762] panfrost ffe40000.gpu: clock rate = 24000000
[   10.052957] meson-ir ff808000.ir: receiver initialized
[   10.054439] panfrost ffe40000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19
[   10.115476] panfrost ffe40000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0
[   10.122916] panfrost ffe40000.gpu: features: 00000000,3fde77ff, issues: 00000000,00000400
[   10.127483] debugfs: File 'Capture' in directory 'dapm' already present!
[   10.130923] panfrost ffe40000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7
[   10.148427] panfrost ffe40000.gpu: shader_present=0x1 l2_present=0x1
[   10.170144] [drm] Initialized panfrost 1.2.0 20180908 for ffe40000.gpu on minor 1
[   10.181893] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   10.199892] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   10.209044] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   10.217548] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   10.229646] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   10.259166] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   10.409610] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   10.410367] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   10.410937] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   10.411326] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   10.411689] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   10.438048] systemd[1]: Found device /sys/subsystem/net/devices/eth0.
[   10.569977] systemd[1]: Found device DataTraveler_3.0 BOOT.
[   10.579237] systemd[1]: Finished Helper to synchronize boot up for ifupdown.
[   10.591405] systemd[1]: Starting File System Check on /dev/disk/by-label/BOOT...
[   10.614991] systemd[1]: Started File System Check Daemon to report status.
[   10.759939] systemd[1]: Finished File System Check on /dev/disk/by-label/BOOT.
[   10.777347] systemd[1]: Mounting /boot...
[   10.842977] systemd[1]: Mounted /boot.
[   10.853169] systemd[1]: Reached target Local File Systems.
[   10.867542] systemd[1]: Starting Armbian ZRAM config...
[   10.880020] systemd[1]: Starting Set console font and keymap...
[   10.891925] systemd[1]: Started ifup for eth0.
[   10.902425] systemd[1]: Starting Raise network interfaces...
[   10.912286] systemd[1]: Starting Preprocess NFS configuration...
[   10.917973] systemd[1]: Condition check resulted in Mark the need to relabel after reboot being skipped.
[   10.926658] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
[   10.936096] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[   10.949754] systemd[1]: Finished Set console font and keymap.
[   10.956296] systemd[1]: nfs-config.service: Succeeded.
[   10.960417] systemd[1]: Finished Preprocess NFS configuration.
[   10.970545] systemd[1]: Starting NFSv4 ID-name mapping service...
[   10.976732] systemd[1]: Condition check resulted in RPC security service for NFS client and server being skipped.
[   10.986157] systemd[1]: Reached target NFS client services.
[   10.993951] systemd[1]: Condition check resulted in RPC security service for NFS server being skipped.
[   11.045579] systemd[1]: Started NFSv4 ID-name mapping service.
[   11.137198] zram: Added device: zram0
[   11.140066] zram: Added device: zram1
[   11.143812] zram: Added device: zram2
[   11.282716] zram0: detected capacity change from 0 to 2000528
[   11.312916] Adding 1000260k swap on /dev/zram0.  Priority:5 extents:1 across:1000260k SSFS
[   11.380047] meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.1:08] driver [Meson G12A Internal PHY] (irq=37)
[   11.391942] meson8b-dwmac ff3f0000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   11.406111] meson8b-dwmac ff3f0000.ethernet eth0: No Safety Features support found
[   11.412163] meson8b-dwmac ff3f0000.ethernet eth0: PTP not supported by HW
[   11.419351] meson8b-dwmac ff3f0000.ethernet eth0: configuring for phy/rmii link mode
[   11.421005] zram1: detected capacity change from 0 to 102400
[   11.507427] zram2: detected capacity change from 0 to 2000528
[   11.571801] EXT4-fs (zram2): mounted filesystem without journal. Opts: discard. Quota mode: none.
[   11.606478] systemd[1]: Finished Armbian ZRAM config.
[   11.624529] systemd[1]: Starting Armbian memory supported logging...
[   11.694151] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard. Quota mode: none.
[   11.702789] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
[   17.233229] systemd[1]: Finished Armbian memory supported logging.
[   17.253036] systemd[1]: Starting Journal Service...
[   17.389540] systemd[1]: Started Journal Service.
[   17.416823] systemd-journald[820]: Received client request to flush runtime journal.

Armbian 22.05.0-trunk Focal ttyAML0

armbian login: [  112.503396] NFSD: Using UMH upcall client tracking operations.
[  112.505149] NFSD: starting 90-second grace period (net f0000081)

@LomotHo LomotHo mentioned this issue Apr 4, 2022
Closed
@ophub
Copy link
Owner

ophub commented Apr 4, 2022

5.15的内核，不写入emmc，在usb使用正常不

@LomotHo
Copy link
Author

LomotHo commented Apr 4, 2022

可以正常使用

@ophub
Copy link
Owner

ophub commented Apr 4, 2022 •
edited
Loading

#129

这个设备由Calmact反馈了测试结果，支持在usb中使用。

写入emmc需要u-boot支持。安装信息是为了测试，他在做u-boot的测试，以后稳定了再添加写入emmc的支持。现在先在usb中使用吧。

感谢你分享的日志，这有助于分析问题

@LomotHo
Copy link
Author

LomotHo commented Apr 4, 2022

他的测试结果和我的一模一样, 如果还需要测试新版本, 我会协助的

@LomotHo LomotHo closed this as completed Apr 4, 2022
@ophub
Copy link
Owner

ophub commented Apr 4, 2022

好的

@ophub
Copy link
Owner

ophub commented Apr 25, 2022

KryptonLee 为这个设备提供了u-boot支持，现在已经可以完美写入emmc使用了。

@ophub ophub added the support This need is supported label Apr 25, 2022
@xcray
Copy link

xcray commented Jul 31, 2022 •
edited
Loading

KryptonLee 为这个设备提供了u-boot支持，现在已经可以完美写入emmc使用了。

我拿到的M401A问题和楼主说的一样，只有用u200的dtb和e900v22c或u200的boot写入emmc才能从emmc启动（不能写bootloader）。

@ophub
Copy link
Owner

ophub commented Jul 31, 2022 •
edited
Loading

哪个文件？

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Assignees
No one assigned
Labels
support This need is supported
Projects
None yet
Milestone
No milestone
Development

No branches or pull requests
3 participants
@LomotHo @xcray @ophub