| title | summary |
|---|---|
Checkpoint Restore |
TiDB v7.1.0 introduces checkpoint restore, allowing interrupted snapshot and log restores to continue without starting from scratch. It records restored shards and table IDs, enabling retries to use the progress point close to the interruption. However, it relies on the GC mechanism and may require some data to be restored again. It's important to avoid modifying cluster data during the restore to ensure accuracy. |
Snapshot restore or log restore might be interrupted due to recoverable errors, such as disk exhaustion and node crash. Before TiDB v7.1.0, the recovery progress before the interruption would be invalidated even after the error is addressed, and you need to start the restore from scratch. For large clusters, this incurs considerable extra cost.
Starting from TiDB v7.1.0, Backup & Restore (BR) introduces the checkpoint restore feature, which enables you to continue an interrupted restore. This feature can retain most recovery progress of the interrupted restore.
If your TiDB cluster is large and cannot afford to restore again after a failure, you can use the checkpoint restore feature. The br command-line tool (hereinafter referred to as br) periodically records the shards that have been restored. In this way, the next restore retry can use a recovery progress point close to the abnormal exit.
The implementation of checkpoint restore is divided into two parts: snapshot restore and log restore. For more information, see Implementation details.
The implementation of snapshot restore is similar to snapshot backup. br restores all SST files within a key range (Region) in batches. After completing a restore, br records this range and the table ID of the restored cluster table. The checkpoint restore feature periodically uploads the new restore information to external storage so that the key ranges that have been restored can be persisted.
When br retries a restore, it reads the key ranges that have been restored from external storage, and matches them with the corresponding table ID. During the restore, br skips any key ranges that overlap with those recorded in the checkpoint restore, and that have the same table ID.
If you delete tables before br retries the restore, the table ID of the newly created table during the retry will be different from the previously recorded table ID in the checkpoint restore. In this case, br bypasses the previous checkpoint restore information and restores the table again. This means that the same table with a new ID disregards the old ID's checkpoint restore information and records the new checkpoint restore information corresponding to the new ID.
Due to the use of the MVCC (Multi-Version Concurrency Control) mechanism, data with specified timestamps can be written unordered and repeatedly.
When restoring database or table DDLs using snapshot restore, the ifExists parameter is added. For existing databases or tables that are already considered created, br automatically skips the restore.
Log restore is the process of restoring data metadata backed up by TiKV nodes (meta-kv) in the order of timestamps. The checkpoint restore first establishes a one-to-one ID mapping relationship between the backup cluster and the restored cluster based on the meta-kv data. This ensures that the ID of meta-kv remains consistent across different restore retries, enabling meta-kv to be restored again.
Unlike snapshot backup files, the range of log backup files might overlap. Thus, the key range cannot be used directly as recovery progress metadata. Additionally, there might be a large number of log backup files. However, each log backup file has a fixed position in the log backup metadata. This means that a unique position in the log backup metadata can be assigned to each log backup file as recovery progress metadata.
The log backup metadata contains an array of file metadata. Each file metadata in the array represents a file composed of multiple log backup files. The file metadata records the offset and size of a log backup file in the concatenated file. Therefore, br can use the triple (log backup metadata name, file metadata array offset, log backup file array offset) to uniquely identify a log backup file.
Checkpoint restore relies on the GC mechanism and cannot record all data that has been restored. The following sections provide the details.
During a log restore, the order of the restored data is unordered, which means that the deletion record of a key might be restored before its write record. If GC is triggered at this time, all data of the key will be deleted and then GC cannot process subsequent write records of the key. To avoid this situation, br pauses GC during log restore. If br exits halfway, GC remains paused.
After the log restore is completed, GC is restarted automatically without manual startup. However, if you decide not to continue the restore, you can manually enable GC as follows:
The principle of br pausing GC is to execute SET config tikv gc.ratio-threshold = -1.0 to set gc.ratio-threshold to a negative number, thus pausing GC. You can manually enable GC by modifying the value of gc.ratio-threshold. For example, to reset to its default value, you can execute SET config tikv gc.ratio-threshold = 1.1.
When br retries a restore, some data that has been restored might need to be restored again, including the data being restored and the data not recorded by the checkpoint.
-
If the interruption is caused by an error,
brpersists the meta information of the data restored before exit. In this case, only the data being restored needs to be restored again in the next retry. -
If the
brprocess is interrupted by the system,brcannot persist the meta information of the data restored to the external storage. Sincebrpersists the meta information every 30 seconds, data restored in the last 30 seconds before interruption cannot be persisted and needs to be restored again in the next retry.
After a restore failure, avoid writing, deleting, or creating tables in the cluster. This is because the backup data might contain DDL operations for renaming tables. If you modify the cluster data, the checkpoint restore cannot decide whether the deleted or existing table are resulted from external operations, which affects the accuracy of the next restore retry.
Checkpoint restore operations are divided into two parts: snapshot restore and PITR restore.
During the initial restore, br creates a __TiDB_BR_Temporary_Snapshot_Restore_Checkpoint database in the target cluster. This database records checkpoint data, the upstream cluster ID, and the BackupTS of the backup data.
If the restore fails, you can retry it using the same command, and br will automatically read the checkpoint information from the __TiDB_BR_Temporary_Snapshot_Restore_Checkpoint database and resume from the last restore point.
If the restore fails and you try to restore backup data with different checkpoint information to the same cluster, br reports an error. It indicates that the current upstream cluster ID or BackupTS is different from the checkpoint record. If the restore cluster has been cleaned, you can manually delete the __TiDB_BR_Temporary_Snapshot_Restore_Checkpoint database and retry with a different backup.
PITR (Point-in-time recovery) consists of snapshot restore and log restore phases.
During the initial restore, br first enters the snapshot restore phase. This phase follows the same process as the preceding snapshot restore: BR records the checkpoint data, the upstream cluster ID, and BackupTS of the backup data (that is, the start time point start-ts of log restore) in the __TiDB_BR_Temporary_Snapshot_Restore_Checkpoint database. If restore fails during this phase, you cannot adjust the start-ts of log restore when resuming checkpoint restore.
When entering the log restore phase during the initial restore, br creates a __TiDB_BR_Temporary_Log_Restore_Checkpoint database in the target cluster. This database records checkpoint data, the upstream cluster ID, and the restore time range (start-ts and restored-ts). If restore fails during this phase, you need to specify the same start-ts and restored-ts as recorded in the checkpoint database when retrying. Otherwise, br will report an error and prompt that the current specified restore time range or upstream cluster ID is different from the checkpoint record. If the restore cluster has been cleaned, you can manually delete the __TiDB_BR_Temporary_Log_Restore_Checkpoint database and retry with a different backup.
Before entering the log restore phase during the initial restore, br constructs a mapping of upstream and downstream cluster database and table IDs at the restored-ts time point. This mapping is persisted in the system table mysql.tidb_pitr_id_map to prevent duplicate allocation of database and table IDs. Deleting data from mysql.tidb_pitr_id_map might lead to inconsistent PITR restore data.