CHANGELOG

Change Log

SCL 20160125
-> promoted vD3.11.3 to v3.11.3 stable

vD3.11.3 SCL 20160125
- replace Adafruit_MCP9808 with new MCP9808 code
- fix bug handling negative temperatures from MCP9808
	
vD3.11.2 SCL 20160120
- fix error displaying negative temperatures... extra - sign leading decimals when negative temperature
	
vD3.11.1 SCL 20160120
- fix bug in handling negative temperatures from DS3231
	
vD3.11.0 SCL 20160112
- added RAPI_I2C. Serial RAPI now enabled by RAPI_SERIAL.
  *WARNING* RAPI_I2C not tested yet and probably doesn't work
  both RAPI_I2C and RAPI_SERIAL may be enabled simultaneously
- call RapiSendEvseState() if POST error
- fix bug, wasn't calling RapiSendEvseState() if HardFault()
- in J1772EvseController::Init() - call RapiSendCommand() with EVSE_STATE_UNKNOWN

SCL 20160111
- change VOLT_PIN to PILOT_PIN
	
SCL 20151211
- change static inline to inline for wiresend/wirerecv() to fix compiler error
	in Arduino 1.6.6
	
SCL 20151125
- added i2caddr.h
- take Wire.begin() out of RTClib.cpp

SCL: 20151011
v3.10.4
- vD3.10.4 promoted to stable

vD3.10.4 SCL 20151110
- update version number
	
SCL 20151022
- added SERDBG - decouple serial diags from SERIALCLI
	
SCL 20151019
- slight tweak to RTClib.cpp compiler warning fix in 3.10.2
	
vD3.10.3 CWK 20151018
- Correcting accumulating kWh and resetting Wh going in and out of sleep state

vD3.10.2 SCL 20151017
- lots of changes to get rid of 1.6.5 compiler warnings(More)
- wmcbrine PR 48: more code shrinking from - manually merged
	
vD3.10.1 SCL 20151017
- merge PR 47 from wmcbrine
 - faster ulong_sqrt()
 - code saving tweaks to u2a() & SaveSettings()
	
vD3.10.0 SCL 20151017
- fix compile error caused by include for LiquidCrystal_I2C.h
	
vD3.10.0 SCL 20151012
- fix bug introduced by diode check state oscillation fix in D3.9.9 - if 
  transition to sleep while charging, on sleep exit would go into VENT REQ error
  -> if pilot voltage in State C range, but PWM off, go to State B
     this is an added safety feature, because State C should never be allowed
     when PWM is off
- fix bug: if enter sleep mode due to time/charge limit met, sleep should
  automatically be cancelled when car disconnected but it was staying in sleep
	
vD3.9.10 CWK 20150920
- GFI Self Test Duty Cylce restored to 50%

vD3.9.9 CWK/SCL 20150914
- fix diode check state oscillation bug (cwk/scl)
- hard fault on vent required (scl)
- setup() - increase I2C device delay from 200 -> 400ms (cwk) for Danny ter Haars board
- code cleanup of temperature monitoring to save 62 bytes
	
vD3.9.8 CWK 20150912
- fix Temperature Monitoring, broken by accident in D3.9.5 
      The original users amperage level is restored properly after an event.

vD3.9.7 SCL 20150905
- raise OpenEVSE temperature thresholds +10C to match OE-II

SCL 20150905
- fix compile error when AMMETER disabled
	
vD3.9.6 SCL 20150818
- for OpenEVSE II, bump up TEMPERATURE_AMBIENT_xxx by 10 due to extra headroom of CUI VSK-S3-12U power supply
	
vD3.9.5 SCL 20150722
- merge changes from temp branch:
	1. EVSE goes to sleep after time/charge limit met.. would stay in sleep
	-> automatically cancel sleep mode when car disconnected *only if* the
	   sleep was induced by time/charge limit
	2. decouple temperature monitoring from J1772EVSEController::Update()
	-> so that temperature is still monitored when EVSE disabled/sleeping
	3. ProcessInputs() removed from J1772EVSEController
	4. added TEMPERATURE_MONITORING_NY (not yet) code .. currently disabled
	-> $GO/$SO RAPI 
	-> added ambient/ir_thresh support
	
vD3.9.4 SCL 20150611
- reduce GFI self test pulse duration from 50% to 33%
	
vD3.9.3.1 SCL 20150611
- craigK PR #46
	
vD3.9.3 SCL 20150608
- add files and edits to restore I2CLCD_PCF8574 build capability
- broken DelayTimer() introduced in 3.9.0
	
vD3.9.2 SCL 20150606
- fix $GF bug
	
vD3.9.1 SCL 20150605
- boost I2C bus to 400KHz
	

SCL20150605
-> promote to v3.9.0 in stable branch
Many thanks to CraigK for his numerous contributions and top notch testing.

vD3.9.0 SCL 20150604-5
- split out Gfi/J1772Pilot/J1772EvseController into separate files
- add support for changing I2C frequency
- increase I2C bus from 100KHz -> 200KHz
- use modified local Wire/twi to get rid of digitalWrite()
- on POST failure, go directly to Setup menu. Setup menu exits to reboot on POST failure
- shrink MaxCurrent/ChargeLimit/TimeLimit menu memory/code by calculating allowed
	values rather than using RAM lookup tables
- put strings in strings.cpp
- fix bugs from 3.8.4: 1) Setup menu Exit sometimes didn't work 2) Setup menu would
	start on Exit item after first use
- GFCI and No Ground faults auto reset when EV is unplugged, even if hard fault
- GFCI and No Ground faults display auto reset countdown when applicable
	GFCI FAULT
	RETRY IN 04:55
- when waiting for timer, just display Sleeping instead of Waiting
- during a fault, short press goes directly to Setup menu instead of putting
	EVSE in Sleep state
- send $WF WIFI_MODE_AP_DEFAULT instead of WIFI_MODE_AP to client on very long
	button press
- fix RAPI bug: $GF was returning FF as trip counts if zero. New max value for
	any trip count = FE
- fix documentation for $SC & $GG
- got rid of superfluous AUTOSTART_MENU and MANUALSTART code
- fixes for TEMPERATURE_MONITORING from CraigK
- fix bugs in Charging screen when KWH_RECORDING or TEMPERATURE_MONITORING not defined


v3.8.4 SCL 20150526
-> pushed to stable branch
	
vD3.8.4 SCL 20150526
- display "Disabled" when EVSE_STATE_DISABLED instead of "Stopped"
- fix bug: RAPI wasn't sending EVSE state ($ST) properly
	
vD3.8.3 SCL 20150518
- fix RAPI bug caused by code compaction in 3.8.x
- have Setup menu exit out of menus instead of back to Settings
	
vD3.8.2 SCL 20150518
- got rid of LcdDetected() .. superfluous, since LiquidTWI2 handles it
	
vD3.8.1 SCL 20150516
- fix bug in settings menu - charge & time limit should only display when EV connected
- when charge or time limit set, exit directly out of menus
- display clock icon when time limit set, lightning bolt icon when charge limit set
- code compaction
	
vD3.8.0 SCL 20150516
- added TIME_LIMIT - charge for a specified time and stop
	
vD3.7.9 SCL 20150515
- fix bug in u2a() when digits=0
- added CHARGE_LIMIT - charge to a certain kWh and then go to sleep
  kudos to AndreE for the charge limit idea.
- move all setup menus to separate "Setup" submenu. Top level menu now
  called "Settings"
	
SCL 20150513
- cleanup, move SERIALCLI to serialcli.cpp/h

v3.7.8 SCL 20150512
* promoted to official release
- Special thanks to CraigK for his hard work in making this release possible,
  with his numerous enhancements, and invaluable testing.

vD3.7.8 SCL 20150511-12
* RELEASE CANDIDATE 3 *
- added RAPI SM,GM to set/get voltmeter
- EEPROM settings for voltmeter scale/offset
- RAPI $GG now returns voltage as well
- read voltmeter in J1772EVSEController::Update() instead of on demand
	(added GetVoltage())
	
vD3.7.7 SCL 20150511
* RELEASE CANDIDATE 2 *
- added RAPI SK,GP,GU commands
- added RAPI XOR checksum and no checksum support (kudos to AndreE for
	suggesting XOR checksum support)

vD3.7.6 SCL 20150510
* RELEASE CANDIDATE 1 *
- added u2a()
- code size reduction of DELAYTIMER_MENU and TEMPERATURE_MONITORING
  -> now, RAPI, DELAYTIMER_MENU, and TEMPERATURE_MONITORING can all be enabled simultaneously
- remove floats from Adafruit libraries (CraigK remove float from open_evse.ino)
- merge CraigK PR#34,35
- added more amp selections to L2 (CraigK)
- change RTC year range from 12-20 -> 15->25
- change RTC/DelayTimer menu behavior - keep leading + when adjusting a value

Much gratitude to CraigK for his many contributions to coding and testing, including,
but not limited to temperature monitoring and kWh logging
	
vD3.7.5 SCL 20150506
- code cleanup
- remove sscanf() - save 2K (thanks to AndreE for the heads up)
- merge CraigK PR#33
- roll back version from .8 -> .5
- change DelayTimer::CheckTime() delay from 1m to 1s
- get rid of FlexiTimer2
	
	
vD3.7.4 SCL 20150429
- enable SAMPLE_ACPINS by default
	
vD3.7.3 SCL 20150429
- no substantial changes.. mainly reorganizing of the code to use the libraries
	in place -> no more copying to Arduino libraries folder
- shorten short button press from 100ms -> 50ms
	
vD3.7.2 SCL 20150428
- added SHOW_DISABLED_TESTS
- try to fix random GFI fault due to UL-mandated GFI self test just before
  closing contacts. Gfi::SelfTest() - add 200ms delay and then clear m_GfiFault
- add code to avoid arcing contacts if user reboots while EVSE is charging

vD3.7.1 SCL 20150427
- fix bug: if entered menu during charging, relay would stay open when user pulled plug from EV
- clean up OnboardDisplay::Update() - added OBD_UPD_xxx
- disable OnboardDisplay::Update() when in menu
- GFI hard fault .. change status to EVSE_STATE_GFI_TEST_FAILED instead of EVSE_GFCI_FAULT
- when rebooting EVSE if our relay is closed, set pilot to +12VDC and wait 3 sec
	to give EV time to open its contactor before we open ours
- UL-mandated GFI test before closing contacts causing spurious GFI faults
	-> add a 200ms delay after GFI test
- during hard fault, disable Exit menu item
- misc code cleanup

vD3.7.0 SCL 20150423
- added avrstuff.h/cpp -> switch from Arduino digital pin functions to
	DigitalPin

vD3.6.9 SCL 20150423
- GFCI test message now "GFCI". Only fault will cause "GFCI FAULT"

vD3.6.8 SCL 20150413
- merge NSayer PR #32 OpenEVSE II streamline

vD3.6.7 SCL 20150410
- merge NSayer PR: Latest OpenEVSE II 1.0 hardware changes #30
1. Gut ReadACPins(). It s unused.
2. GROUND_TEST_PIN is gone in the 1.0 hardware.
3. RELAY_TEST_PIN is high when charging or it s a ground fail. It s low
when not charging or it s a stuck relay.

vD3.6.6 SCL 20150406
- added SAMPLE_ACPINS logic for setup with MID400 using inline diodes
- added FT_ENDURANCE and FT_READ_AC_PINS
- replace booleans w/ uint8_t
- in GfiSelfTest() delay(50) when reading GFI_PIN
- add GFI self test before closing relay per UL (UL_GFI_SELFTEST)
- change GFI_TEST_CYCLES 50->60 GFI_PULSE_DURATION_US 8000->8333

vD3.6.5 SCL 20150406
- added HardFault()
- GFI_RETRY_COUNT 255 -> 6 and GFI_TIMEOUT 1min -> 5min
- set SERVICE REQUIRED message after GFI retries exhausted
- added nosave parm to SetCurrentCapacity()

vD3.6.4 SCL 20150406
- fix compile error in rapi_proc.cpp due to prog_char fix
- CraigK Patch 6: temp monitoring and kWh recording
- CraigK OpenEvse II ammeter calibration (Craigk46 patch 8)
- SCL move g_ampacity to g_TempMonitor.m_ampacity

vD3.6.3 SCL 20150403
- fix compile errors in Arduino 1.5.8+ due to deprecation of prog_char

vD3.6.2 SCL 20150326
- add delay(200) to beginning of setup() to fix random LCD black out at boot
	Thanks to CraigK!
- code cleanup on KWH_RECORDING .. change eeprom_read_byte() to eeprom_read_dword()

vD3.6.1 SCL 20150311
- merge CraigK patch-4 temp monitoring fixes

vD3.6.0 SCL 20150301
- add CraigK TEMPERATURE_MONITORING

vD3.5.2 SCL 20150226
- minor fixes for millis() overflow handling
- change code to allow RED_LED_PIN and GREEN_LED_PIN to be commented out w/o causing compile errors

SCL 20150220
- merge NSayer pull request OpenEVSE II hardware now only performs ground test during charging

vD3.5.1 SCL 20150218
- added FT_GFI_LOCKOUT/FT_GFI_RETRY for functional testing
- per UL Fred Reyes, stuck relay always results in hard fault (lockout)
- GFI_RETRY_COUNT to 255 (infinite) instead of 15

vD3.5.0 SCL 20150216
- added UL_COMPLIANT: UL wants EVSE to hard fault (cease operation until manual intervention)
  1) if POST fails
  2) if fault happens immediately after charge starts
- consolidated some redundant fault strings
- if AutoSvcLevel couldn't be detected due to car being plugged in during POST,
  and L1 was set because of this, upon first charge session, we will detect the
  actual svc level, and switch to L2 if detected

vD3.4.3 SCL 20150213
- don't do GFI self test in doPost() if other fault already found
- when in menus, lock out all other functions until exit 
- do stuck relay chk in POST even if EV is plugged in and AutoSvcLevel()
- for safety, set to L1 if AutoSvcLevel and car is plugged in during POST,
  because we can't auto detect level.

vD3.4.2 SCL 20150210
- added SLEEP_STATUS_PIN
	
vD3.4.1 SCL 20150205
- forgot to set svcState to SR when stuck relay test fails in doPost() and
	not AutoSvcLevel()
	
vD3.4.0 SCL 20150123
- added writing of safety check trip counters to EEPROM
- added RAPI $GF
- setting GFI_RETRY_COUNT to 255 will make it retry indefinitely
- changed GFI_RETRY_COUNT from 3 to 15, GFI_TIMEOUT from 15min to 1min
  -> now, tests will retry 15 times at one minute intervals
     instead of 3 retries at 15 min intervals
	
vD3.3.7 SCL 20150122
- merged NSayer pull requests #19,#20
  - OpenEVSE II changes + added relay check menu item
	
vD3.3.6 SCL 20150120
- enable WATCHDOG by default
- minor refactoring of watchdog code
- perform relay stuck check in doPost() even if not auto svc level
	
vD3.3.5 SCL 20150113
- merge NSAYER pull request for OpenEVSE II code
	
vD3.3.4 SCL 20150102
- switch from EEPROM.h to avr/eeprom.h functions
	
vD3.3.3 SCL 20150102
- clear charging current in chargingOff() - thanks to CapnBry
	
vD3.3.2 SCL 20141205
- added very long press RAPI code for WiFi AP mode reset ($WF)
	
vD3.3.1 SCL 20141124
- fix some random crashes caused by string overflow on LCD display
  one such crash was when I2CLCD enabled and RTC enabled w/o RTC hardware
	
vD3.3.0 SCL 20141120
- promote version to 3.3.x since features were added
	
vD3.2.9 SCL 20141120
- make ammeter calibration mode volatile
	
vD3.2.8 SCL 20141119
- restructure and fix ammeter bugs
- don't update charging amps display unless ammeter value is updated
- don't show charging amps if m_CurrentScaleFactor == 0
- replace moving average w/ sliding window average to save RAM
- added ammeter calibration RAPI function $S2
- replace redundant calls to millis() with variable in J1772EVSEController::Update()
	
vD3.2.7 SCL 20141111
- fixed ammeter no display bug introduced in 3.2.6

v3.2.6 SCL 20141111
- restructured ammeter code
- add RAPI SF,SA,GA,GG commands

v3.2.5 SCL 20141111
- don't display charging current <1A
	
v3.2.4 SCL 20141110
- minor fixes to RAPI
- added CraigK's current averaging AMMETER_AVERAGING
	
v3.2.3 SCL 20140829
- added support for PCF8574-based I2C LCD backpacks
	
v3.2.2 SCL 20140829
- setting RGB/mono backlight fixes
	
v3.2.1 SCL 20140826
- fix POST problem when LCD not attached
- remove superfluous m_menuidx added in last update
	
v3.2.0 SCL 20140825
- revamped SetupMenu to greatly simplify adding/removing items
- added LCD backlight type setting to menus (C. Howell)
	
v3.1.0 SCL 20140822
- added CHARGING_PINAC
- promote from alpha to production status
	
v3.1.A9 SCL 20140418
- fixed bug in saving GFI self test setting
	
v3.1.A8 SCL 20140417
- added S.Low's (scanchain) CheckTime() fixes
	
v3.1.A7 SCL 20140417
- bumped version to 3.x.x to avoid confusion w/ main branch code
	
v2.1.A7 SCL 20140417
- added nsayer's GFI_SELFTEST + menu tweaks
	
v2.0.B8 20131118
- merge v2.0.B7 from open_evse google group + some minor tweaks
	
v2.0.B3 20130714
- fix LCD display error
- merged changes from Scott Rubin
	
v2.0.B1 20130119
- added RTC + delay timer code from Goldserve
	
v1.0.9 SCL 20130101
- don't hang when I2CLCD/RGBLCD enabled, and no LCD installed. requires
  LiquidTWI2 v1.2.0+
	
v1.0.8 SCL 20121025
- change button reading from analogRead() to digitalRead(), enable internal pullup
	
v1.0.7 SCL 20121023
- fix bug in Max Current Menu.. couldn't display highest selectable value
  on init
	
v1.0.6 SCL
- switch LCD library to LiquidTWI2 to save memory, speed up LCD
  writing, and decrease latency
	
v1.0.5 SCL
- move g_psEnabled/g_psEnabled to #ifdef SERIALCLI to fix compile
  error when LCD and BTN_MENU disabled
	
v1.0.4 SCL
- BTN_ENABLE_TOGGLE reverts code from v1.0.3
- refine duty cycle calc in SetPWM() (thanks to Lee Howard)
	
v1.0.3 SCL
- short press no longer does anything when menus not active
  instead of emergency start/stop
- button menus only available in connected and charging states
	
v1.0.0
First official release
Button Menu

v0.5.0
Adafruit RGB LCD and LCD backpack support
Support for Advanced Power Supply
	
v0.4.0
Command Line Interface (CLI)
Write Current setting to EEPROM
Serial Baud Rate 38400
CLI Commands: "show" "set amp" "save" "help"


v0.3.0
GFI code debugged and working.
Now compiles with Arduino 1.0

v.0.2.0	
Firmware for use with Arduino-0022. Tested as working.