Ubiquiti Antenna Bandwidth, Range, Modulation Rate Expectiations - Planning Total

[Pedro-on-a-bike]

^{This initial comment is collaborative and open to modification by all.}

Task Summary

🎟️ Re-ticketed from: #
📅 Due date: N/A
🎯 Success criteria:
❌ Blocked by:
👈 Depends on:

Point to Point Links, all Mbps values are aggregate
EIRP Limit at 36dBm must be used in Unii 1 or 3, EIRP limit above 36dBm must be used in Unii3

To be more conservative, it is possible to assume a lower x modulation for expected bandwidth if the signal is on threshold:
80MHz Channel, Modulation Rate 1x,2x,4x,8x, Signal Threshold -81,-79,-71,-65,-59
100MHz Channel, Modulation Rate 1x,2x,4x,8x,10x, Signal Threshold -80,-78,-69,-63,-57,-51

Litebeam 5AC Gen 2 - Settings - 13dBm Tx Power, 36 dBm EIRP, 80Mhz Width
1.5km, -51dBm Signal, 8x Mod, 597 Mbps
3.0km, -57dBm Signal, 6x Mod, 497 Mbps
6.0km, -63dBm Signal, 6x Mod, 448 Mbps

Nanobeam 5AC Gen 2 - Settings - 17dBm Tx Power, 36 dBm EIRP, 80Mhz Width
1.5km, -55dBm Signal, 8x Mod, 597 Mbps
3.0km, -61dBm Signal, 6x Mod, 448 Mbps
6.0km, -67dBm Signal, 6x Mod, 398 Mbps

Powerbeam 5AC Gen 2 - Settings - 11dBm Tx Power, 36 dBm EIRP, 80Mhz Width
1.5km, -50dBm Signal, 8x Mod, 662 Mbps
3.0km, -56dBm Signal, 6x Mod, 497 Mbps
6.0km, -62dBm Signal, 6x Mod, 448 Mbps
12.0km, -69dBm Signal, 4x Mod, 298 Mbps

Powerbeam 5AC Gen 2 - Settings - 20dBm Tx Power, 45 dBm EIRP, 80Mhz Width
1.5km, -41dBm Signal, 8x Mod, 662 Mbps
3.0km, -47dBm Signal, 8x Mod, 662 Mbps
6.0km, -53dBm Signal, 8x Mod, 597 Mbps
12.0km, -59dBm Signal, 6x Mod, 497 Mbps

airFiber 5XHD, 23dBi Ant - Settings - 13dBm Tx Power, 36 dBm EIRP, 100Mhz Width
1.5km, -51dBm Signal, 8x Mod, 876 Mbps
3.0km, -57dBm Signal, 6x Mod, 657 Mbps
6.0km, -63dBm Signal, 4x Mod, 438 Mbps
12.0km, -69dBm Signal, 2x Mod, 219 Mbps

airFiber 5XHD, 30dBi Ant - Settings - 19dBm Tx Power, 49 dBm EIRP, 100Mhz Width
1.5km, -31dBm Signal, 10x Mod, 1094 Mbps
3.0km, -37dBm Signal, 10x Mod, 1094 Mbps
6.0km, -43dBm Signal, 10x Mod, 1094 Mbps
12.0km, -49dBm Signal, 10x Mod, 1094 Mbps

[darkdrgn2k]

I think this would be a good document to add to the docs
especially when chooseing CPE