-
Notifications
You must be signed in to change notification settings - Fork 4
/
Copy pathhdw.dat.hok
102 lines (102 loc) · 5.53 KB
/
hdw.dat.hok
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
# Hardware parameters for Hokkaido radar.
#
# Each radar has a distinct set of hardware parameters that are used
# by the radar control software and the analysis software. These
# parameters are read in a distinct order and are assumed to have
# specific units. If either the order of the parameters or their units
# are incorrect, the processing and analysis software will produce
# incorrect answers that may not be easily identified. It is the
# responsibility of the SuperDARN P.I.s to insure that the hdw.dat files
# for their radars are correct and that these files are updated as
# required to accurately represent the physical state of the radar and
# that copies of these files are retained under revision control by Rob
# Barnes. Revision controlled versions of hdw.dat files are destributed
# with SuperDARN radar control software and with analysis software.
#
# The hardware parameters are distributed as a string of values
# delineated by one or more spaces. The following table specifies the
# parameters, their units, and a brief description of their meaning.
#
# 01) Station ID (unique numerical value). Assigned by Rob Barnes.
# 02) Last year that parameter string is valid. (4 digit year).
# 03) Last second of year that parameter string is valid (range 0 to
# 34163999 for non-leap years). The parameter string giving the current
# configuration is assumed to be valid until the last second of 2999.
# 04) Geographic latitude of radar site (Given in decimal degrees to 3
# decimal places. Southern hemisphere values are negative)
# 05) Geographic longitude of radar site (Given in decimal degrees to
# 3 decimal places. West longitude values are negative)
# 06) Altitude of the radar site (meters)
# 07) Scanning boresight (Direction of the center beam, measured in
# degrees relative to geographic north. CCW rotations are negative.)
# 08) Beam separation (Angular separation in degrees between adjacent
# beams. Normally 3.24 degrees)
# 09) Velocity sign (At the radar level, backscattered signals with
# frequencies above the transmitted frequency are assigned positive
# Doppler velocities while backscattered signals with frequencies below
# the transmitted frequency are assigned negative Doppler velocity. This
# convention can be reversed by changes in receiver design or in the
# data samping rate. This parameter is set to +1 or -1 to maintain the
# convention.)
#
# Some SuperDARN radars have analog receivers whereas others have
# analog front-end receivers followed by digital receivers. Analog
# receivers and analog front-ends can have gain and bandwidth controls
# that are identified here and corrected in the radar control software.
# Digital receiver information is retained and compensated for within
# the digital receiver driver.
#
# 10) Analog Rx attenuator step (dB)
#
# In order to obtain information on the vertical angle of arrival of
# the backscattered signals, the SuperDARN radars include a four antenna
# interferometer array in addition to the 16 antenna main array. This
# second array is typically displaced from the main array along the
# array normal direction and the different path length due to the
# displacement and the different cable lengths between the antenna
# arrays and their phasing matrices introduces a phase shift that is
# dependent on the elevation angle of the returning backscattered
# signal.
#
# 11) Tdiff (Propagation time from interferometer array antenna to
# phasing matrix input minus propagation time from main array antenna
# through transmitter to phasing matrix input. If the signal from the
# interferometer comes first, then tdiff < 0. Units are in decimal
# microseconds)
# 12) Phase sign (Cabling errors can lead to a 180 degree shift of the
# interferometry phase measurement. +1 indicates that the sign is
# correct, -1 indicates that it must be flipped.)
# 13) Interferometer offset (Displacement of midpoint of
# interferometer array from midpoint of main array. This is given in
# meters in Cartesian coordinates. X is along the line of antennas with
# +X toward higher antenna numbers, Y is along the array normal
# direction with +Y in the direction of the array normal. Z is the
# altitude difference, +Z up.)
#
# More analog receiver information
#
# 14) Analog Rx rise time (Time given in microseconds. Time delays of
# less than ~10 microseconds can be ignored. If narrow-band filters are
# used in analog receivers or front-ends, the time delays should be
# specified.)
# 15) Analog attenuation stages (Number of stages. This is used for
# gain control of an analog receiver or front-end.)
# 16) Maxinum of range gates used (Number of gates. This is used for
# allocation of array storage.)
# 17) Maximum number of beams to be used at a particular radar site.
# (Number of beams. It is important to specify the true maximum. This
# will assure that a given beam number always points in the same
# direction. A subset of these beams, e.g. 8-23, can be used for
# standard 16 beam operation.)
#
# **********************************************************************
# ==Notes==
#
#
# **********************************************************************
#
# 1 2 3 4 5 6 7 8 9 10 11 12 13(1) 13(2) 13(3) 14 15 16 17
#
# UNTIL 01/Jan/3000 05:45:36.0
40 2999 31556736 43.530 143.610 480.0 30.0 3.24 1 10 0.000 1 0.0 -100.0 2.9 100.0 7 110 16
# EOF