Skip to content

Latest commit

 

History

History
129 lines (102 loc) · 3.4 KB

README.md

File metadata and controls

129 lines (102 loc) · 3.4 KB
Raw

diod

diod is a multi-threaded, user space file server that speaks 9P2000.L protocol.

Building

On Debian

sudo apt-get install build-essential libpopt-dev ncurses-dev automake autoconf git
sudo apt-get install liblua5.1-dev libmunge-dev libwrap0-dev libcap-dev libattr1-dev
./autogen.sh
./configure
make
make check

On Red Hat

sudo yum install epel-release gperftools-devel automake autoconf libattr-devel
sudo yum install lua-devel munge-devel tcp_wrappers-devel libcap-devel
./autogen.sh
./configure
make
make check

On FreeBSD

portmaster security/munge
portmaster lang/lua53
./autogen.sh
./configure
make

See also the remarks below if you want a server that supports impersonation (access=user in v9fs).

Kernel Client

The kernel 9P client, sometimes referred to as "v9fs", consists of the 9p.ko file system module, and its network transport module, 9pnet.ko.

Although the kernel client supports several 9P variants, diod only supports 9P2000.L, and only in its feature-complete form, as it appeared in 2.6.38.

Earlier versions of the kernel that do not support 9P2000.L will fail at mount time when version negotiation fails. Some pre-2.6.38 versions of the kernel that have 9P2000.L but still send some 9P2000.u ops may fail in less obvious ways. Use a 2.6.38 or later kernel.

Quick Start

Start the diod server in foreground, with protocol debugging to stderr, no authentication, and one export:

sudo ./diod -f -d 1 -n -e /tmp/9

Mount it using the raw mount command:

sudo mount -t 9p -n 127.0.0.1 /mnt \
    -oaname=/tmp/9,version=9p2000.L,uname=root,access=user

Or (simpler), mount it using diodmount:

sudo ./diodmount -n localhost:/tmp/9 /mnt

Or (even simpler) if diodmount is installed as /sbin/mount.diod:

sudo mount -t diod -n localhost:/tmp/9 /mnt

I/O forwarding on clusters:

On I/O node, set up /etc/diod.conf according to diod.conf(5), then:

chkconfig diod on
service diod start

On compute node, if I/O node is fritz42, add entries like this to /etc/fstab:

fritz42:/g/g0  /g/g0         diod  default 0 0

Alternatively, use "zero-config" automounter method:

  • set DIOD_SERVERS="fritz42" in /etc/sysconfig/auto.diod1
  • add /d /etc/auto.diod to /etc/auto.master Then:
mkdir /d
chkconfig autofs on
service autofs start
ln -s /d/g.g0 /g/g0

Note that at this point diod is only being tested with NFS file systems. Use it with Lustre or GPFS at your own peril - but if you do, please report issues!

Impersonation on FreeBSD

FreeBSD does not support per-thread credentials. If you want a diod server that supports v9fs' access=user, you can:

  • build diod with --enable-impersonation (disabled by default on FreeBSD)
  • install net/nfs-ganesha-kmod from ports (or at least the modules setthreadgid, setthreadgroups and setthreaduid) or from source
  • before stating diod, load the modules providing additional syscalls:
kldload /path/to/nfs-ganesha-kmod/setthreaduid/setthreaduid.ko
kldload /path/to/nfs-ganesha-kmod/setthreadgid/setthreadgid.ko
kldload /path/to/nfs-ganesha-kmod/setthreadgroups/setthreadgroups.ko

Please read nfs-ganesha-kmod's README first, and use at your own risk.

Support

Use GitHub!

Diod can also be discussed on the v9fs-users mailing list