Raspberry Pi Pico SDK Examples See Getting Started with the Raspberry Pi Pico and the README in the pico-sdk for information
on getting up and running.
App
Description
hello_adc Display the voltage from an ADC input.
joystick_display Display a Joystick X/Y input based on two ADC inputs.
adc_console An interactive shell for playing with the ADC. Includes example of free-running capture mode.
App
Description
hello_48MHz Change the system clock frequency to 48 MHz while running.
hello_gpout Use the general purpose clock outputs (GPOUT) to drive divisions of internal clocks onto GPIO outputs.
hello_resus Enable the clock resuscitate feature, "accidentally" stop the system clock, and show how we recover.
App
Description
build_variants Builds two version of the same app with different configurations
App
Description
hello_dma Use the DMA to copy data in memory.
control_blocks Build a control block list, to program a longer sequence of DMA transfers to the UART.
channel_irq Use an IRQ handler to reconfigure a DMA channel, in order to continuously drive data through a PIO state machine.
App
Description
cache_perfctr Read and clear the cache performance counters. Show how they are affected by different types of flash reads.
nuke Obliterate the contents of flash. An example of a NO_FLASH binary (UF2 loaded directly into SRAM and runs in-place there). A useful utility to drag and drop onto your Pico if the need arises.
program Erase a flash sector, program one flash page, and read back the data.
xip_stream Stream data using the XIP stream hardware, which allows data to be DMA'd in the background whilst executing code from flash.
ssi_dma DMA directly from the flash interface (continuous SCK clocking) for maximum bulk read performance.
App
Description
hello_7segment Use the GPIOs to drive a seven segment LED display.
hello_gpio_irq Register an interrupt handler to run when a GPIO is toggled.
dht_sensor Use GPIO to bitbang the serial protocol for a DHT temperature/humidity sensor.
See also: blink , blinking an LED attached to a GPIO.
App
Description
hello_divider Show how to directly access the hardware integer dividers, in case AEABI injection is disabled.
App
Description
bus_scan Scan the I2C bus for devices and display results.
lcd_1602_i2c Display some text on a generic 16x2 character LCD display, via I2C.
mpu6050_i2c Read acceleration and angular rate values from a MPU6050 accelerometer/gyro, attached to an I2C bus.
App
Description
hello_interp A bundle of small examples, showing how to access the core-local interpolator hardware, and use most of its features.
App
Description
hello_multicore Launch a function on the second core, printf some messages on each core, and pass data back and forth through the mailbox FIFOs.
multicore_fifo_irqs On each core, register and interrupt handler for the mailbox FIFOs. Show how the interrupt fires when that core receives a message.
multicore_runner Set up the second core to accept, and run, any function pointer pushed into its mailbox FIFO. Push in a few pieces of code and get answers back.
App
Description
blinky Blink "hello, world" in Morse code on Pico's LED
button Use Pico's BOOTSEL button as a regular button input, by temporarily suspending flash access.
App
Description
hello_pio Absolutely minimal example showing how to control an LED by pushing values into a PIO FIFO.
apa102 Rainbow pattern on on a string of APA102 addressable RGB LEDs.
differential_manchester Send and receive differential Manchester-encoded serial (BMC).
hub75 Display an image on a 128x64 HUB75 RGB LED matrix.
i2c Scan an I2C bus.
logic_analyser Use PIO and DMA to capture a logic trace of some GPIOs, whilst a PWM unit is driving them.
manchester_encoding Send and receive Manchester-encoded serial.
pio_blink Set up some PIO state machines to blink LEDs at different frequencies, according to delay counts pushed into their FIFOs.
pwm Pulse width modulation on PIO. Use it to gradually fade the brightness of an LED.
spi Use PIO to erase, program and read an external SPI flash chip. A second example runs a loopback test with all four CPHA/CPOL combinations.
squarewave Drive a fast square wave onto a GPIO. This example accesses low-level PIO registers directly, instead of using the SDK functions.
st7789_lcd Set up PIO for 62.5 Mbps serial output, and use this to display a spinning image on a ST7789 serial LCD.
uart_rx Implement the receive component of a UART serial port. Attach it to the spare Arm UART to see it receive characters.
uart_tx Implement the transmit component of a UART serial port, and print hello world.
ws2812 Examples of driving WS2812 addressable RGB LEDs.
addition Add two integers together using PIO. Only around 8 billion times slower than Cortex-M0+.
App
Description
hello_pwm Minimal example of driving PWM output on GPIOs.
led_fade Fade an LED between low and high brightness. An interrupt handler updates the PWM slice's output level each time the counter wraps.
measure_duty_cycle Drives a PWM output at a range of duty cycles, and uses another PWM slice in input mode to measure the duty cycle.
App
Description
hello_reset Perform a hard reset on some peripherals, then bring them back up.
App
Description
hello_rtc Set a date/time on the RTC, then repeatedly print the current time, 10 times per second, to show it updating.
rtc_alarm Set an alarm on the RTC to trigger an interrupt at a date/time 5 seconds into the future.
rtc_alarm_repeat Trigger an RTC interrupt once per minute.
App
Description
bme280_spi Attach a BME280 temperature/humidity/pressure sensor via SPI.
mpu9250_spi Attach a MPU9250 accelerometer/gyoscope via SPI.
spi_dma Use DMA to transfer data both to and from the SPI simultaneously. The SPI is configured for loopback.
spi_flash Erase, program and read a serial flash device attached to one of the SPI controllers.
App
Description
hello_double_tap On dev boards with a reset button (but no BOOTSEL), a magic number in RAM can be used to enter the USB bootloader, when the reset button is pressed twice quickly.
narrow_io_write Demonstrate the effects of 8-bit and 16-bit writes on a 32-bit IO register.
unique_board_id Read the 64 bit unique ID from external flash, which serves as a unique identifier for the board.
App
Description
hello_timer Set callbacks on the system timer, which repeat at regular intervals. Cancel the timer when we're done.
periodic_sampler Sample GPIOs in a timer callback, and push the samples into a concurrency-safe queue. Pop data from the queue in code running in the foreground.
timer_lowlevel Example of direct access to the timer hardware. Not generally recommended, as the SDK may use the timer for IO timeouts.
App
Description
hello_uart Print some text from one of the UART serial ports, without going through stdio.
uart_advanced Use some other UART features like RX interrupts, hardware control flow, and data formats other than 8n1.
App
Description
host_hid Use USB in host mode to poll an attached HID keyboard (TinyUSB example)
App
Description
hello_watchdog Set the watchdog timer, and let it expire. Detect the reboot, and halt.