i2c.pio

;
; Copyright (c) 2020 Raspberry Pi (Trading) Ltd.
;
; SPDX-License-Identifier: BSD-3-Clause
;

.program i2c
.side_set 1 opt pindirs

; TX Encoding:
; | 15:10 | 9     | 8:1  | 0   |
; | Instr | Final | Data | NAK |
;
; If Instr has a value n > 0, then this FIFO word has no
; data payload, and the next n + 1 words will be executed as instructions.
; Otherwise, shift out the 8 data bits, followed by the ACK bit.
;
; The Instr mechanism allows stop/start/repstart sequences to be programmed
; by the processor, and then carried out by the state machine at defined points
; in the datastream.
;
; The "Final" field should be set for the final byte in a transfer.
; This tells the state machine to ignore a NAK: if this field is not
; set, then any NAK will cause the state machine to halt and interrupt.
;
; Autopull should be enabled, with a threshold of 16.
; Autopush should be enabled, with a threshold of 8.
; The TX FIFO should be accessed with halfword writes, to ensure
; the data is immediately available in the OSR.
;
; Pin mapping:
; - Input pin 0 is SDA, 1 is SCL (if clock stretching used)
; - Jump pin is SDA
; - Side-set pin 0 is SCL
; - Set pin 0 is SDA
; - OUT pin 0 is SDA
; - SCL must be SDA + 1 (for wait mapping)
;
; The OE outputs should be inverted in the system IO controls!
; (It's possible for the inversion to be done in this program,
; but costs 2 instructions: 1 for inversion, and one to cope
; with the side effect of the MOV on TX shift counter.)

do_nack:
    jmp y-- entry_point        ; Continue if NAK was expected
    irq wait 0 rel             ; Otherwise stop, ask for help

do_byte:
    set x, 7                   ; Loop 8 times
bitloop:
    out pindirs, 1         [7] ; Serialise write data (all-ones if reading)
    nop             side 1 [2] ; SCL rising edge
    wait 1 pin, 1          [4] ; Allow clock to be stretched
    in pins, 1             [7] ; Sample read data in middle of SCL pulse
    jmp x-- bitloop side 0 [7] ; SCL falling edge

    ; Handle ACK pulse
    out pindirs, 1         [7] ; On reads, we provide the ACK.
    nop             side 1 [7] ; SCL rising edge
    wait 1 pin, 1          [7] ; Allow clock to be stretched
    jmp pin do_nack side 0 [2] ; Test SDA for ACK/NAK, fall through if ACK

public entry_point:
.wrap_target
    out x, 6                   ; Unpack Instr count
    out y, 1                   ; Unpack the NAK ignore bit
    jmp !x do_byte             ; Instr == 0, this is a data record.
    out null, 32               ; Instr > 0, remainder of this OSR is invalid
do_exec:
    out exec, 16               ; Execute one instruction per FIFO word
    jmp x-- do_exec            ; Repeat n + 1 times
.wrap

% c-sdk {

#include "hardware/clocks.h"
#include "hardware/gpio.h"


static inline void i2c_program_init(PIO pio, uint sm, uint offset, uint pin_sda, uint pin_scl) {
    assert(pin_scl == pin_sda + 1);
    pio_sm_config c = i2c_program_get_default_config(offset);

    // IO mapping
    sm_config_set_out_pins(&c, pin_sda, 1);
    sm_config_set_set_pins(&c, pin_sda, 1);
    sm_config_set_in_pins(&c, pin_sda);
    sm_config_set_sideset_pins(&c, pin_scl);
    sm_config_set_jmp_pin(&c, pin_sda);

    sm_config_set_out_shift(&c, false, true, 16);
    sm_config_set_in_shift(&c, false, true, 8);

    float div = (float)clock_get_hz(clk_sys) / (32 * 100000);
    sm_config_set_clkdiv(&c, div);

    // Try to avoid glitching the bus while connecting the IOs. Get things set
    // up so that pin is driven down when PIO asserts OE low, and pulled up
    // otherwise.
    gpio_pull_up(pin_scl);
    gpio_pull_up(pin_sda);
    uint32_t both_pins = (1u << pin_sda) | (1u << pin_scl);
    pio_sm_set_pins_with_mask(pio, sm, both_pins, both_pins);
    pio_sm_set_pindirs_with_mask(pio, sm, both_pins, both_pins);
    pio_gpio_init(pio, pin_sda);
    gpio_set_oeover(pin_sda, GPIO_OVERRIDE_INVERT);
    pio_gpio_init(pio, pin_scl);
    gpio_set_oeover(pin_scl, GPIO_OVERRIDE_INVERT);
    pio_sm_set_pins_with_mask(pio, sm, 0, both_pins);

    // Clear IRQ flag before starting
    hw_clear_bits(&pio->inte0, 1u << sm);
    hw_clear_bits(&pio->inte1, 1u << sm);
    pio->irq = 1u << sm;

    // Configure and start SM
    pio_sm_init(pio, sm, offset + i2c_offset_entry_point, &c);
    pio_sm_set_enabled(pio, sm, true);
}

%}


.program set_scl_sda
.side_set 1 opt

; Assemble a table of instructions which software can select from, and pass
; into the FIFO, to issue START/STOP/RSTART. This isn't intended to be run as
; a complete program.

    set pindirs, 0 side 0 [7] ; SCL = 0, SDA = 0
    set pindirs, 1 side 0 [7] ; SCL = 0, SDA = 1
    set pindirs, 0 side 1 [7] ; SCL = 1, SDA = 0
    set pindirs, 1 side 1 [7] ; SCL = 1, SDA = 1

% c-sdk {
// Define order of our instruction table
enum {
    I2C_SC0_SD0 = 0,
    I2C_SC0_SD1,
    I2C_SC1_SD0,
    I2C_SC1_SD1
};
%}