12 Jul 11:07

MTB CAT1 Peripheral Driver Library v3.11.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Implementation Details

CAT1C: Support for TVIIC2D6M devices: cyt4dnjbas, cyt4dnjbbs, cyt4dnjbcs, cyt4dnjbds, cyt4dnjbes, cyt4dnjbfs, cyt4dnjbgs, cyt4dnjbhs, cyt4dnjbjs, cyt4dnjbks, cyt4dnjbls, cyt4dnjbms, cyt4dnjbns, cyt4dnjbps, cyt4dnjbqs, cyt4dnjbrs

Build Changes

Personality Changes

New Personalities (in 8.0 folder):
- eth-1.0.cypersonality
Updated Personalities (in 8.0 folder):
- peripheral:
  - smif_v2-1.0.cypersonality
  - emusb-1.0.cypersonality
  - dma-3.0.cypersonality
- platform:
  - axidmac-1.0.cypersonality
  - bakclk-3.0.cypersonality
  - dma-3.0.cypersonality
  - lfclk-3.0.cypersonality
  - lpeco_prescaler-1.0.cypersonality
  - lepco-1.0.cypersonality
  - power_v3-1.0.cypersonality
  - sysclock-3.0.cypersonality
  - wco-3.0.cypersonality

Added Drivers

AXIDMAC 1.0

Updated Drivers

Drivers with patch version updates

Obsoleted part numbers

Known Issues

CAT1A: In device-configurator, certain IP is not completely available for some devices as some combinations of pin connections are not valid.
- CYT2BL4BAS/CYT2BL4CAE: SCB6 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- CYT2BL3CAE, CYT2B7CAE: SCB1 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- On the following devices: CAN FD 0 Channel 3, CAN FD 1 Channel 1, CAN FD 1 Channel 3 is not available (no signal for CAN Rx Pin available).
  - CYT2BL4BAS, CYT2BL3CAE, CYT2BL3CAS, CYT2BL4CAE, CYT2BL3BAE, CYT2BL4BAE, CYT2BL4CAS, CYT2BL3BAS, CYT2B73BAS, CYT2B73CAS, CYT2B73BAE
Traveo II B-E: Does not support emulated eeprom.
CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.4.1
Infineon HAL	2.6.0
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.40.2
ARM Compiler 6	6.16
FreeRTOS	10.4.305
Device Database	4.16.0

More information

Assets 2

12 Jul 11:03

steveomner

release-v3.10.1

0212f1e

MTB CAT1 Peripheral Driver Library v3.10.1

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Implementation Details

CAT1B: New devices added: cyw20829b0000, cyw20829b0010, cyw20829b0021, cyw89829b0022, cyw89829b0232

Build Changes

Personality Changes

Added Drivers

No new drivers added.

Updated Drivers

Drivers with patch version updates

Obsoleted part numbers

Known Issues

CAT1A: In device-configurator, certain IP is not completely available for some devices as some combinations of pin connections are not valid.
- CYT2BL4BAS/CYT2BL4CAE: SCB6 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- CYT2BL3CAE, CYT2B7CAE: SCB1 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- On the following devices: CAN FD 0 Channel 3, CAN FD 1 Channel 1, CAN FD 1 Channel 3 is not available (no signal for CAN Rx Pin available).
  - CYT2BL4BAS, CYT2BL3CAE, CYT2BL3CAS, CYT2BL4CAE, CYT2BL3BAE, CYT2BL4BAE, CYT2BL4CAS, CYT2BL3BAS, CYT2B73BAS, CYT2B73CAS, CYT2B73BAE
Traveo II B-E: Does not support emulated eeprom.
CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.4.1
Infineon HAL	2.6.0
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.40.2
ARM Compiler 6	6.16
FreeRTOS	10.4.305
Device Database	4.15.0

More information

Assets 2

01 Apr 05:29

alokmoondra

release-v3.10.0

dc2df2d

MTB CAT1 Peripheral Driver Library v3.10.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Implementation Details

CAT1A: Adds Traveo II Body Entry device support. Devices added:

cyt2b63bae cyt2b63bas cyt2b63cae cyt2b63cas cyt2b64bae cyt2b64bas cyt2b64cae cyt2b64cas
cyt2b65bae cyt2b65bas cyt2b65cae cyt2b65cas cyt2b93bae cyt2b93bas cyt2b93cae cyt2b93cas
cyt2b94bae cyt2b94bas cyt2b94cae cyt2b94cas cyt2b95bae cyt2b95bas cyt2b95cae cyt2b95cas
cyt2b97bae cyt2b97bas cyt2b97cae cyt2b97cas cyt2b98bae cyt2b98bas cyt2b98cae cyt2b98cas

Build Changes

Personality Changes

Updated Personalities : adcmic-1.0.cypersonality,canfd-3.0.cypersonality,comp-1.0.cypersonality,connectivity_wifi-1.0.cypersonality,counter_v2-1.0.cypersonality,counter-1.0.cypersonality,ctdac-1.0.cypersonality,ezi2c-3.0.cypersonality,
i2c-4.0.cypersonality, i2s-2.0.cypersonality, keyscan-1.1.cypersonality, lpcomp-2.0.cypersonality, mcwdt-3.0.cypersonality, opamp-1.0.cypersonality, pdm_pcm_v2-3.0.cypersonality,pdm_pcm-1.1.cypersonality,
pwm_v2-1.0.cypersonality, pwm-1.0.cypersonality, quaddec_v2-1.0.cypersonality, quaddec-1.0.cypersonality,rtc-3.0.cypersonality, sar2-1.0.cypersonality, sar-6.0.cypersonality, sd_host-1.0.cypersonality, shiftreg_v2-1.0.cypersonality,
smif_intrinsic-1.0.cypersonality, smif_v2-1.0.cypersonality, smif-1.2.cypersonality, spi-3.0.cypersonality, tdm-1.1.cypersonality, uart-3.0.cypersonality, bakclk-3.0.cypersonality, debug-2.0.cypersonality,dma-3.0.cypersonality,
eco_prescaler-1.0.cypersonality, eco-3.0.cypersonality, extclk-3.0.cypersonality, hfclk_v2-1.0.cypersonality, hfclk-3.0.cypersonality, iho-1.0.cypersonality, lfclk-3.0.cypersonality, mfclk-3.0.cypersonality, pathmux-3.0.cypersonality,
pclk_v2-1.0.cypersonality, pclk-3.0.cypersonality, periclk-2.0.cypersonality, pilo-3.0.cypersonality, pin-3.0.cypersonality, power_v2-1.0.cypersonality, power_v3-1.0.cypersonality, pumpclk-3.0.cypersonality, sysclock-3.0.cypersonality.
tickclk-3.0.cypersonality, timerclk-3.0.cypersonality, wco-3.0.cypersonality.

Added Drivers

No new drivers added.

Updated Drivers

Drivers with patch version updates

Obsoleted part numbers

Known Issues

CAT1A: In device-configurator, certain IP is not completely available for some devices as some combinations of pin connections are not valid.
- CYT2BL4BAS/CYT2BL4CAE: SCB6 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- CYT2BL3CAE, CYT2B7CAE: SCB1 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- On the following devices: CAN FD 0 Channel 3, CAN FD 1 Channel 1, CAN FD 1 Channel 3 is not available (no signal for CAN Rx Pin available).
  - CYT2BL4BAS, CYT2BL3CAE, CYT2BL3CAS, CYT2BL4CAE, CYT2BL3BAE, CYT2BL4BAE, CYT2BL4CAS, CYT2BL3BAS, CYT2B73BAS, CYT2B73CAS, CYT2B73BAE
Traveo II B-E: Does not support emulated eeprom.
CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.4.1
Infineon HAL	2.6.0
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.40.2
ARM Compiler 6	6.16
FreeRTOS	10.4.305
Device Database	4.14.0

More information

Assets 2

31 Jan 12:46

alokmoondra

release-v3.9.0

96bbf19

MTB CAT1 Peripheral Driver Library v3.9.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Implementation Details

CAT1A: New devices added cy8c6146bti_f54, cy8c6147bti_f54, cy8c6246bti_d54 and cy8c6247bti_d54.
CAT1B: CYW89829 support added.
CAT1B: 20829 IAR support added.
CAT1B: Support for 20829A0 device has been removed.

Build Changes

Personality Changes

Updated Personalities (in 8.0 folder):
- peripheral:
  - connectivity_wifi-1.0.cypersonality

Added Drivers

No new drivers added.

Updated Drivers

Drivers with patch version updates

SCB 3.10.1

Obsoleted part numbers

Known Issues

CAT1A: In device-configurator, certain IP is not completely available for some devices as some combinations of pin connections are not valid.
- CYT2BL4BAS/CYT2BL4CAE: SCB6 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- CYT2BL3CAE, CYT2B7CAE: SCB1 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- On the following devices: CAN FD 0 Channel 3, CAN FD 1 Channel 1, CAN FD 1 Channel 3 is not available (no signal for CAN Rx Pin available).
  - CYT2BL4BAS, CYT2BL3CAE, CYT2BL3CAS, CYT2BL4CAE, CYT2BL3BAE, CYT2BL4BAE, CYT2BL4CAS, CYT2BL3BAS, CYT2B73BAS, CYT2B73CAS, CYT2B73BAE
Traveo II B-E: Does not support emulated eeprom.
CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.4.1
Infineon HAL	2.5.4
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.3
ARM Compiler 6	6.16
FreeRTOS	10.4.305

More information

Assets 2

31 Jan 12:45

alokmoondra

release-v3.8.0

71f964c

MTB CAT1 Peripheral Driver Library v3.8.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Implementation Details

CAT1A: Adds Traveo II Body Entry device support. Devices added:

cyt2b73cas cyt2b74bae cyt2b74bas cyt2b74cae cyt2b74cas cyt2b75bae cyt2b75bas cyt2b75cae cyt2b75cas cyt2b77bae
cyt2b77bas cyt2b77cae cyt2b77cas cyt2b78bae cyt2b78bas cyt2b78cae cyt2b78cas cyt2bl3bae cyt2bl3bas cyt2bl3cae
cyt2bl3cas cyt2bl4bae cyt2bl4bas cyt2bl4cae cyt2bl4cas cyt2bl5bae cyt2bl5bas cyt2bl5cae cyt2bl5cas cyt2bl7bae
cyt2bl7bas cyt2bl7cae cyt2bl7cas cyt2bl8bae cyt2bl8bas cyt2bl8cae cyt2bl8cas

Updates drivers to support Traveo II B-E devices. (See drivers list below.)
Updates personalities for Traveo II B-E devices.
Updates IP headers with new-to-CAT1A IP to support Traveo II B-E devices.
Adds linker scripts and adjusts cat1a system/startup code to work with Traveo II B-E devices.
CAT1C: Removes some CAT1C SysPm APIs that were not hardware compatible with XMC7xxx devices.
In order to provide CAT1A support for the TVIIBE PERIv2 hardware, and still provide CAT1A/CAT1B/CAT1B compatibility with cy_sysclk_v2, PERI_DIV_n_NR macros have been renamed to PERI_CLK_GR_DIV_n_NR. Any application code using the old macros must be updated to use the new macro names.
Personality fixes: Some personality fixes where IP from other categories overlapped with TVIIBE (mostly CAT1C) were applied to schema v8 personalities.
Bug fix: Updates Prot driver API availability based on the PERI version. Some devices may have a reduced set of functions available. If code called APIs not appropriate for the version of PERI, that code will not build without updating to reflect new API availability. Please note, however, that if code was calling those APIs and the functions are no longer available, there will be no functional difference as the calls were available before but did nothing if the device hardware didn't support the function.

Build Changes

Personality Changes

Updated Personalities (in 8.0 folder):
- peripheral:
  - evtgen-1.0.cypersonality
  - mcwdt_v2-1.0.cypersonality
  - rtc-3.0.cypersonality
- platform:
  - bakclk-3.0.cypersonality
  - eco-3.0.cypersonality
  - eco_prescaler-1.0.cypersonality
  - extclk-3.0.cypersonality
  - fastclk-2.0.cypersonality
  - fll-4.0.cypersonality
  - hfclk-3.0.cypersonality
  - ilo-3.0.cypersonality
  - imo-3.0.cypersonality
  - lfclk-3.0.cypersonality
  - memclk-1.0.cypersonality
  - pathmux-3.0.cypersonality
  - periclk-2.0.cypersonality
  - pll-3.0.cypersonality
  - pll400-1.0.cypersonality
  - power_v3-1.0.cypersonality
  - slowclk-2.0.cypersonality
  - sysclock-3.0.cypersonality
  - tickclk-3.0.cypersonality
  - timerclk-3.0.cypersonality
  - wco-3.0.cypersonality

Added Drivers

No new drivers required for TVIIBE.

Updated Drivers

Flash
GPIO
IPC
LVD
MCWDT
PROT
RTC
SysClk
SysInt
SysLib
SysPm
WDT
BLE_CLK

Drivers with patch version updates

Obsoleted part numbers

Known Issues

CAT1A: In device-configurator, certain IP is not completely available for some devices as some combinations of pin connections are not valid.
- CYT2BL4BAS/CYT2BL4CAE: SCB6 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- CYT2BL3CAE, CYT2B7CAE: SCB1 is complete only for UART, cannot support I2C, EZI2C, or SPI.
- On the following devices: CAN FD 0 Channel 3, CAN FD 1 Channel 1, CAN FD 1 Channel 3 is not available (no signal for CAN Rx Pin available).
  - CYT2BL4BAS, CYT2BL3CAE, CYT2BL3CAS, CYT2BL4CAE, CYT2BL3BAE, CYT2BL4BAE, CYT2BL4CAS, CYT2BL3BAS, CYT2B73BAS, CYT2B73CAS, CYT2B73BAE
Traveo II B-E: Does not support emulated eeprom.
CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.4.1
Infineon HAL	2.5.4
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.3
ARM Compiler 6	6.16
FreeRTOS	10.4.305

More information

Assets 2

29 Sep 05:22

alokmoondra

release-v3.7.0

94eb787

MTB CAT1 Peripheral Driver Library v3.7.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Some restrictions apply to the PSoC 64 devices configuration. Please refer to PRA (Protected Register Access) driver documentation for the details.

Implementation Details

CAT1A: Dual Bank Support added in Flash driver for CAT1A. Note that this feature is not supported on PSoC 64 devices.
CAT1A: Correction done in the SCB instances of MPN CYBLE-416045-02-device
Personality re-structuring: Personality supporting Schema v8 added. Personalities_8.0 is a copy of ‘personalities’ with needed personalities updated to use schema v8. In order to allow for personalities in a single device support library to be able to control if they are available on the MCU and/or companion-connectivity devices in a design, the ‘Dependencies’ section of the personality file has been expanded. These personalities can specify the required operating mode for the device for it to be valid on it. The valid operating mode values: MCU, COMPANION_CONNECTIVITY. These personalities are available in folder device-info/personalities_8.0. Personalities supporting schema v8 are visible in MTB 3.1. For backward compatibility with MTB 3.0, this release will also have older personalities in folder device-info/personalities.
Personality fixes: The schema v8 personalities include minor fixes over the personalities with older schema. In future releases, all the personality fixes will be done in schema v8 personalities.

Build Changes

Personalities Changes

Updated Personalities (in 8.0 folder): imo-3.0.cypersonality, eco-3.0.cypersonality

Added Drivers

Updated Drivers

FLASH 3.80

Drivers with patch version updates

Obsoleted part numbers

The ModusToolbox Device Configurator can not create the designs targeting the obsolete PSoC 6 part numbers.

Below is a list of PSoC 6 part numbers obsoleted in psoc6pdl release-v1.6.0, with the suggested next best alternative:

Obsoleted part number	Next best alternative
CY8C624AAZI-D44	CY8C624AAZI-S2D44
CY8C624AFNI-D43	CY8C624AFNI-S2D43
CY8C624ABZI-D04	CY8C624ABZI-S2D04
CY8C624ABZI-D14	CY8C624ABZI-S2D14
CY8C624AAZI-D14	CY8C624AAZI-S2D14
CY8C6248AZI-D14	CY8C6248AZI-S2D14
CY8C6248BZI-D44	CY8C6248BZI-S2D44
CY8C6248AZI-D44	CY8C6248AZI-S2D44
CY8C6248FNI-D43	CY8C6248FNI-S2D43
CY8C624ALQI-D42	N/A

Known Issues

CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.3.0
Infineon HAL	2.4.0
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.3
ARM Compiler 6	6.16
FreeRTOS	10.4.305

More information

Assets 2

29 Sep 05:21

alokmoondra

release-v3.6.0

5322fee

MTB CAT1 Peripheral Driver Library v3.6.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Some restrictions apply to the PSoC 64 devices configuration. Please refer to PRA (Protected Register Access) driver documentation for the details.

Implementation Details

CAT1B: CYW20829 Enhancements
CAT1B: CYW20829 DSRAM support for ARM Compiler
CAT1B Defect Fix: For API Cy_WDT_SetIgnoreBits, valid input range is changed to 0-21 for CAT1B devices, this will change the API's behaviour, follow the API documentation and use this API accordingly.

Build Changes

Personalities Changes

Updated Personalities : pilo-3.0.cypersonality, power_v2-1.0.cypersonality

Added Drivers

Updated Drivers

Drivers with patch version updates

EFUSE 2.30.1

Obsoleted part numbers

The ModusToolbox Device Configurator can not create the designs targeting the obsolete PSoC 6 part numbers.

Below is a list of PSoC 6 part numbers obsoleted in psoc6pdl release-v1.6.0, with the suggested next best alternative:

Obsoleted part number	Next best alternative
CY8C624AAZI-D44	CY8C624AAZI-S2D44
CY8C624AFNI-D43	CY8C624AFNI-S2D43
CY8C624ABZI-D04	CY8C624ABZI-S2D04
CY8C624ABZI-D14	CY8C624ABZI-S2D14
CY8C624AAZI-D14	CY8C624AAZI-S2D14
CY8C6248AZI-D14	CY8C6248AZI-S2D14
CY8C6248BZI-D44	CY8C6248BZI-S2D44
CY8C6248AZI-D44	CY8C6248AZI-S2D44
CY8C6248FNI-D43	CY8C6248FNI-S2D43
CY8C624ALQI-D42	N/A

Known Issues

CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.3.0
Infineon HAL	2.4.0
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.3
ARM Compiler 6	6.16
FreeRTOS	10.4.305

More information

Assets 2

29 Sep 05:19

alokmoondra

release-v3.4.0

84afadc

MTB CAT1 Peripheral Driver Library v3.4.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Some restrictions apply to the PSoC 64 devices configuration. Please refer to PRA (Protected Register Access) driver documentation for the details.

Implementation Details

Cryptolite Support for ECDSA verify for HASHZERO message added.
CAT1C:Enabled wait-states API.
Glitch filter support added for TCPWM version 3 and above.
CAT1A: Added new 80-m-csp package mpns in PSoC 6-256K family. MPNs starting with CY8C6144FMI, CY8C6244FMI.

Build Changes

Personalities Changes

Added Personalities : smartio-4.0.cypersonality
Updated Personalities : bakclk-3.0.cypersonality, timerclk-3.0.cypersonality, tickclk-3.0.cypersonality, sysclock-3.0.cypersonality, power_v3-1.0.cypersonality, power_v2-1.0.cypersonality, pin-3.0.cypersonality, pclk_v2-1.0.cypersonality,
mfclk-3.0.cypersonality, hfclk-3.0.cypersonality, hfclk_v2-1.0.cypersonality, eco-3.0.cypersonality, uart-3.0.cypersonality, tdm-1.1.cypersonality, smif_v2-1.0.cypersonality, smartio-3.0.cypersonality, sd_host-1.0.cypersonality, pwm_v2-1.0.cypersonality, pdm_pcm_v2-3.0.cypersonality, mcwdt-3.0.cypersonality, i2c-4.0.cypersonality, canfd-3.0.cypersonality

Added Drivers

Updated Drivers

Drivers with patch version updates

Obsoleted part numbers

The ModusToolbox Device Configurator can not create the designs targeting the obsolete PSoC 6 part numbers.

Below is a list of PSoC 6 part numbers obsoleted in psoc6pdl release-v1.6.0, with the suggested next best alternative:

Obsoleted part number	Next best alternative
CY8C624AAZI-D44	CY8C624AAZI-S2D44
CY8C624AFNI-D43	CY8C624AFNI-S2D43
CY8C624ABZI-D04	CY8C624ABZI-S2D04
CY8C624ABZI-D14	CY8C624ABZI-S2D14
CY8C624AAZI-D14	CY8C624AAZI-S2D14
CY8C6248AZI-D14	CY8C6248AZI-S2D14
CY8C6248BZI-D44	CY8C6248BZI-S2D44
CY8C6248AZI-D44	CY8C6248AZI-S2D44
CY8C6248FNI-D43	CY8C6248FNI-S2D43
CY8C624ALQI-D42	N/A

Known Issues

CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
Design configuration will not be auto migrated from smartio-3.0.cypersonality to smartio-4.0.cypersonality. So, existing projects should use smartio-3.0.cypersonality. New projects can make use of smartio-4.0.cypersonality which includes additional improvements.
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.3.0
Infineon HAL	2.4.0
CMSIS	5.8.0
GCC Compiler	11.3.1
IAR Compiler	9.3
ARM Compiler 6	6.16
FreeRTOS	10.4.305

More information

Assets 2

29 Sep 05:19

alokmoondra

release-v3.3.1

8ed7d45

MTB CAT1 Peripheral Driver Library v3.3.1

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Some restrictions apply to the PSoC 64 devices configuration. Please refer to PRA (Protected Register Access) driver documentation for the details.

Implementation Details

CAT1B: Added support for CYW20829B0
CAT1B: Verified with GCC_ARM toolchain
Updated crypto version

Build Changes

Personalities Changes

Updated Personalities : bakclk-3.0.cypersonality

Added Drivers

Updated Drivers

Drivers with patch version updates

Obsoleted part numbers

The ModusToolbox Device Configurator can not create the designs targeting the obsolete PSoC 6 part numbers.

Below is a list of PSoC 6 part numbers obsoleted in psoc6pdl release-v1.6.0, with the suggested next best alternative:

Obsoleted part number	Next best alternative
CY8C624AAZI-D44	CY8C624AAZI-S2D44
CY8C624AFNI-D43	CY8C624AFNI-S2D43
CY8C624ABZI-D04	CY8C624ABZI-S2D04
CY8C624ABZI-D14	CY8C624ABZI-S2D14
CY8C624AAZI-D14	CY8C624AAZI-S2D14
CY8C6248AZI-D14	CY8C6248AZI-S2D14
CY8C6248BZI-D44	CY8C6248BZI-S2D44
CY8C6248AZI-D44	CY8C6248AZI-S2D44
CY8C6248FNI-D43	CY8C6248FNI-S2D43
CY8C624ALQI-D42	N/A

Known Issues

CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.3.0
Infineon HAL	2.4.0
CMSIS	5.8.0
GCC Compiler	10.3.1
IAR Compiler	9.3
ARM Compiler 6	6.16
FreeRTOS	10.4.303

More information

Assets 2

29 Sep 05:18

alokmoondra

release-v3.3.0

92f4669

MTB CAT1 Peripheral Driver Library v3.3.0

Please refer to the README.md and the
PDL API Reference Manual
for a complete description of the Peripheral Driver Library.

Some restrictions apply to the PSoC 64 devices configuration. Please refer to PRA (Protected Register Access) driver documentation for the details.

Implementation Details

Crypto AES GCM support for CAT1A
Inrush mode selection support in BT-IPC for CAT1B
DEEPSLEEP-RAM support addition for CAT1B
Bug fixes
MISRA 2012 fixes done for few drivers

Build Changes

Personalities Changes

Updated Personalities : counter_v2-1.0.cypersonality, counter-1.0.cypersonality, csd-3.0.cypersonality, emusb-1.0.cypersonality,
i2c-4.0.cypersonality, mcwdt_v2-1.0.cypersonality, pwm_v2-1.0.cypersonality, quaddec_v2-1.0.cypersonality, sar2-1.0.cypersonality, sar-6.0.cypersonality, shiftreg_v2-1.0.cypersonality, smif_v2-1.0.cypersonality, althf-1.1.cypersonality, bakclk-3.0.cypersonality, eco_prescaler-1.0.cypersonality, fll-4.0.cypersonality, hfclk_v2-1.0.cypersonality, iho-1.0.cypersonality, lfclk-3.0.cypersonality, mfclk-3.0.cypersonality, mfo-3.0.cypersonality, periclk-2.0.cypersonality, pin-3.0.cypersonality, power_v2-1.0.cypersonality, sysclock-3.0.cypersonality

Added Drivers

Updated Drivers

Drivers with patch version updates

Obsoleted part numbers

The ModusToolbox Device Configurator can not create the designs targeting the obsolete PSoC 6 part numbers.

Below is a list of PSoC 6 part numbers obsoleted in psoc6pdl release-v1.6.0, with the suggested next best alternative:

Obsoleted part number	Next best alternative
CY8C624AAZI-D44	CY8C624AAZI-S2D44
CY8C624AFNI-D43	CY8C624AFNI-S2D43
CY8C624ABZI-D04	CY8C624ABZI-S2D04
CY8C624ABZI-D14	CY8C624ABZI-S2D14
CY8C624AAZI-D14	CY8C624AAZI-S2D14
CY8C6248AZI-D14	CY8C6248AZI-S2D14
CY8C6248BZI-D44	CY8C6248BZI-S2D44
CY8C6248AZI-D44	CY8C6248AZI-S2D44
CY8C6248FNI-D43	CY8C6248FNI-S2D43
CY8C624ALQI-D42	N/A

Known Issues

CAT1A: On soft reset, user need to reset back up domain using Cy_SysLib_ResetBackupDomain() to receive Cy_RTC_CenturyInterrupt() callback on Century roll over.
On building with tools 2.2, user get warning related to the older version of tools used. To avoid this warning, user is advised to migrate to newer tools version or keep working with previous version of this library. The warning generated is as follows:
- #warning "(Library) The referenced 'device support library' contains newer content than is supported. Either downgrade the version of the 'device support library' referenced or upgrade the version of tools being used
CAT1C: This release does not support D-CACHE on CAT1C platform

Defect Fixes

See the Changelog section of each Driver in the PDL API Reference for all fixes and updates.

Supported Software and Tools

This version of PDL was validated for compatibility with the following Software and Tools:

Software and Tools	Version
Infineon Core Library	1.3.0
Infineon HAL	2.2.0
CMSIS	5.8.0
GCC Compiler	10.3.1
IAR Compiler	9.3
ARM Compiler 6	6.16
FreeRTOS	10.4.303

More information

Assets 2

Releases: Infineon/mtb-pdl-cat1