Added example config for Ender5Pro 422 with Micro-Swiss Direct Drive and BLtouch

config/default/Configuration_adv.h

@@ -3271,7 +3271,6 @@
 
 #endif // HAS_TRINAMIC_CONFIG
 
-
 // @section i2cbus
 
 //

config/examples/CTC/Bizer/Configuration_adv.h

@@ -610,8 +610,8 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-// #define E0_AUTO_FAN_PIN -1
-// #define E1_AUTO_FAN_PIN -1
+//#define E0_AUTO_FAN_PIN -1
+//#define E1_AUTO_FAN_PIN -1
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
 #define E4_AUTO_FAN_PIN -1

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration_adv.h

@@ -3268,7 +3268,6 @@
 
 #endif // HAS_TRINAMIC_CONFIG
 
-
 // @section i2cbus
 
 //

config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration.h

@@ -23,6 +23,9 @@
 #error "Don't build with import-2.1.x configurations!"
 #error "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."
 
+//#define ENDER5_USE_BLTOUCH
+//#define ENDER5_USE_MICROSWISS
+
 /**
  * Configuration.h
  *
@@ -644,6 +647,10 @@
     #define DEFAULT_Kp_LIST {  21.73,  21.73 }
     #define DEFAULT_Ki_LIST {   1.54,   1.54 }
     #define DEFAULT_Kd_LIST {  76.55,  76.55 }
+  #elif ENABLED(ENDER5_USE_MICROSWISS)
+    #define DEFAULT_Kp  46.45
+    #define DEFAULT_Ki   5.86
+    #define DEFAULT_Kd  91.97
   #else
     #define DEFAULT_Kp  21.73
     #define DEFAULT_Ki   1.54
@@ -1158,7 +1165,7 @@
  * Override with M201
  *                                      X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 500, 500, 100, 5000 }
+#define DEFAULT_MAX_ACCELERATION      { 700, 700, 100, 5000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
@@ -1191,7 +1198,7 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
   #define DEFAULT_XJERK 10.0
   #define DEFAULT_YJERK 10.0
@@ -1253,7 +1260,7 @@
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 
 // Force the use of the probe for Z-axis homing
-//#define USE_PROBE_FOR_Z_HOMING
+#define USE_PROBE_FOR_Z_HOMING
 
 /**
  * Z_MIN_PROBE_PIN
@@ -1270,7 +1277,7 @@
  *      - normally-closed switches to GND and D32.
  *      - normally-open switches to 5V and D32.
  */
-//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
+#define Z_MIN_PROBE_PIN PB1 // Pin 32 is the RAMPS default
 
 /**
  * Probe Type
@@ -1307,7 +1314,9 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#if ENABLED(ENDER5_USE_BLTOUCH)
+  #define BLTOUCH
+#endif
 
 /**
  * MagLev V4 probe by MDD
@@ -1459,7 +1468,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -40, -13, -1.45 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1650,10 +1659,10 @@
  */
 //#define Z_IDLE_HEIGHT Z_HOME_POS
 
-//#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT  4        // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                                   // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
 
-//#define Z_AFTER_HOMING  10      // (mm) Height to move to after homing Z
+#define Z_AFTER_HOMING  10        // (mm) Height to move to after homing Z
 
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
@@ -1731,7 +1740,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM    // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1849,7 +1858,9 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#if ENABLED(ENDER5_USE_BLTOUCH)
+  #define AUTO_BED_LEVELING_BILINEAR
+#endif
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1858,16 +1869,16 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
  * Auto-leveling needs preheating
  */
-//#define PREHEAT_BEFORE_LEVELING
+#define PREHEAT_BEFORE_LEVELING
 #if ENABLED(PREHEAT_BEFORE_LEVELING)
-  #define LEVELING_NOZZLE_TEMP 120   // (°C) Only applies to E0 at this time
-  #define LEVELING_BED_TEMP     50
+  #define LEVELING_NOZZLE_TEMP 180   // (°C) Only applies to E0 at this time
+  #define LEVELING_BED_TEMP     55
 #endif
 
 /**
@@ -1900,11 +1911,13 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #if ENABLED(ENDER5_USE_BLTOUCH)
+    #define G26_MESH_VALIDATION
+  #endif
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for G26.
-    #define MESH_TEST_HOTEND_TEMP  205    // (°C) Default nozzle temperature for G26.
+    #define MESH_TEST_HOTEND_TEMP  200    // (°C) Default nozzle temperature for G26.
     #define MESH_TEST_BED_TEMP      60    // (°C) Default bed temperature for G26.
     #define G26_XY_FEEDRATE         20    // (mm/s) Feedrate for G26 XY moves.
     #define G26_XY_FEEDRATE_TRAVEL 100    // (mm/s) Feedrate for G26 XY travel moves.
@@ -1926,7 +1939,7 @@
 
     // Beyond the probed grid, continue the implied tilt?
     // Default is to maintain the height of the nearest edge.
-    //#define EXTRAPOLATE_BEYOND_GRID
+    #define EXTRAPOLATE_BEYOND_GRID
 
     //
     // Experimental Subdivision of the grid by Catmull-Rom method.
@@ -1946,10 +1959,10 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
-  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+  #define MESH_EDIT_GFX_OVERLAY     // Display a graphics overlay while editing the mesh
 
-  #define MESH_INSET 1              // Set Mesh bounds as an inset region of the bed
-  #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
+  #define MESH_INSET 10             // Set Mesh bounds as an inset region of the bed
+  #define GRID_MAX_POINTS_X  9      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   //#define UBL_HILBERT_CURVE       // Use Hilbert distribution for less travel when probing multiple points
@@ -1980,19 +1993,21 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#if ENABLED(ENDER5_USE_BLTOUCH)
+  #define LCD_BED_LEVELING
+#endif
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
   #define LCD_PROBE_Z_RANGE 4     // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
-  //#define MESH_EDIT_MENU        // Add a menu to edit mesh points
+  #define MESH_EDIT_MENU          // Add a menu to edit mesh points
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LCD_BED_TRAMMING
+#define LCD_BED_TRAMMING
 
 #if ENABLED(LCD_BED_TRAMMING)
-  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
+  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 }  // (mm) Left, Front, Right, Back insets
   #define BED_TRAMMING_HEIGHT      0.0        // (mm) Z height of nozzle at leveling points
   #define BED_TRAMMING_Z_HOP       4.0        // (mm) Z height of nozzle between leveling points
   //#define BED_TRAMMING_INCLUDE_CENTER       // Move to the center after the last corner
@@ -2053,15 +2068,17 @@
  * - Allows Z homing only when XY positions are known and trusted.
  * - If stepper drivers sleep, XY homing may be required again before Z homing.
  */
-//#define Z_SAFE_HOMING
+#if ENABLED(ENDER5_USE_BLTOUCH)
+  #define Z_SAFE_HOMING
+#endif
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
   #define Z_SAFE_HOMING_Y_POINT Y_CENTER  // Y point for Z homing
 #endif
 
 // Homing speeds (linear=mm/min, rotational=°/min)
-#define HOMING_FEEDRATE_MM_M { (20*60), (20*60), (4*60) }
+#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
 
 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS
@@ -2195,7 +2212,7 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
@@ -2481,7 +2498,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 //#define INDIVIDUAL_AXIS_HOMING_SUBMENU
 
 //

config/examples/Creality/Ender-5 Pro/CrealityV422/Configuration_adv.h

@@ -524,7 +524,7 @@
   // Use TEMP_SENSOR_BOARD as a trigger for enabling the controller fan
   //#define CONTROLLER_FAN_MIN_BOARD_TEMP 40  // (°C) Turn on the fan if the board reaches this temperature
 
-  //#define CONTROLLER_FAN_EDITABLE         // Enable M710 configurable settings
+  #define CONTROLLER_FAN_EDITABLE           // Enable M710 configurable settings
   #if ENABLED(CONTROLLER_FAN_EDITABLE)
     #define CONTROLLER_FAN_MENU             // Enable the Controller Fan submenu
   #endif
@@ -878,7 +878,7 @@
 
   // Safety: The probe needs time to recognize the command.
   //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
+  #define BLTOUCH_DELAY 500
 
   /**
    * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
@@ -1310,7 +1310,7 @@
 //#define LCD_BACKLIGHT_TIMEOUT 30 // (s) Timeout before turning off the backlight
 
 #if HAS_BED_PROBE && EITHER(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
-  //#define PROBE_OFFSET_WIZARD       // Add a Probe Z Offset calibration option to the LCD menu
+  #define PROBE_OFFSET_WIZARD         // Add a Probe Z Offset calibration option to the LCD menu
   #if ENABLED(PROBE_OFFSET_WIZARD)
     /**
      * Enable to init the Probe Z-Offset when starting the Wizard.
@@ -1562,7 +1562,7 @@
   // LCD's font must contain the characters. Check your selected LCD language.
   //#define UTF_FILENAME_SUPPORT
 
-  //#define LONG_FILENAME_HOST_SUPPORT    // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
+  #define LONG_FILENAME_HOST_SUPPORT      // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
   //#define LONG_FILENAME_WRITE_SUPPORT   // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
 
   #define SCROLL_LONG_FILENAMES           // Scroll long filenames in the SD card menu
@@ -2024,10 +2024,12 @@
 
   //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #if HAS_BED_PROBE
+    #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #endif
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
-    //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+    #define BABYSTEP_ZPROBE_GFX_OVERLAY     // Enable graphical overlay on Z-offset editor
   #endif
 #endif
 
@@ -2226,7 +2228,7 @@
   #define MIN_CIRCLE_SEGMENTS    72   // Minimum number of segments in a complete circle
   //#define ARC_SEGMENTS_PER_SEC 50   // Use the feedrate to choose the segment length
   #define N_ARC_CORRECTION       25   // Number of interpolated segments between corrections
-  //#define ARC_P_CIRCLES             // Enable the 'P' parameter to specify complete circles
+  #define ARC_P_CIRCLES               // Enable the 'P' parameter to specify complete circles
   //#define SF_ARC_FIX                // Enable only if using SkeinForge with "Arc Point" fillet procedure
 #endif
 
@@ -2569,7 +2571,7 @@
  *
  * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2609,7 +2611,7 @@
   //#define FILAMENT_CHANGE_RESUME_ON_INSERT      // Automatically continue / load filament when runout sensor is triggered again.
   //#define PAUSE_REHEAT_FAST_RESUME              // Reduce number of waits by not prompting again post-timeout before continuing.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define PARK_HEAD_ON_PAUSE                      // Park the nozzle during pause and filament change.
   //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
   //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
@@ -3229,7 +3231,7 @@
     //#define V_STALL_SENSITIVITY  8
     //#define W_STALL_SENSITIVITY  8
     //#define SPI_ENDSTOPS              // TMC2130 only
-    //#define IMPROVE_HOMING_RELIABILITY
+    #define IMPROVE_HOMING_RELIABILITY
   #endif
 
   /**
@@ -3455,8 +3457,6 @@
     #endif
 
     // Define the minimum and maximum test pulse time values for a laser test fire function
-    #define LASER_TEST_PULSE_MIN           1   // Used with Laser Control Menu
-    #define LASER_TEST_PULSE_MAX         999   // Caution: Menu may not show more than 3 characters
     #define LASER_TEST_PULSE_MIN           1   // (ms) Used with Laser Control Menu
     #define LASER_TEST_PULSE_MAX         999   // (ms) Caution: Menu may not show more than 3 characters
 
@@ -3507,7 +3507,6 @@
      */
     //#define LASER_POWER_TRAP
 
-
     //
     // Laser I2C Ammeter (High precision INA226 low/high side module)
     //
@@ -3882,7 +3881,7 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
   //#define HOST_PAUSE_M76                // Tell the host to pause in response to M76
   //#define HOST_PROMPT_SUPPORT           // Initiate host prompts to get user feedback

config/examples/LulzBot/Mini2/Teensy/Configuration_adv.h

@@ -3275,7 +3275,6 @@
 
 #endif // HAS_TRINAMIC_CONFIG
 
-
 // @section i2cbus
 
 //

config/examples/Sovol/SV-01/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h

@@ -1382,7 +1382,7 @@
   //#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
 
   // On the Info Screen, display XY with one decimal place when possible
- // #define LCD_DECIMAL_SMALL_XY
+  //#define LCD_DECIMAL_SMALL_XY
 
   // Add an 'M73' G-code to set the current percentage
   //#define LCD_SET_PROGRESS_MANUALLY