Add LULZBOT_TOUCH_UI (#14967)

MarlinFirmware · Aug 16, 2019 · 274934a · 274934a
1 parent 179d6c4
commit 274934a
Show file tree

Hide file tree

Showing 356 changed files with 22,195 additions and 58 deletions.
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
@@ -2033,6 +2033,12 @@
 //
 //#define MALYAN_LCD
 
+//
+// LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays
+// See Configuration_adv.h for all configuration options.
+//
+//#defined LULZBOT_TOUCH_UI
+
 //
 // Third-party or vendor-customized controller interfaces.
 // Sources should be installed in 'src/lcd/extensible_ui'.

diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
@@ -1143,6 +1143,53 @@
 
 #endif // HAS_GRAPHICAL_LCD
 
+//
+// Lulzbot Touch UI
+//
+#if ENABLED(LULZBOT_TOUCH_UI)
+  // Display board used
+  //#define LCD_FTDI_VM800B35A        // FTDI 3.5" with FT800 (320x240)
+  //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
+  //#define LCD_HAOYU_FT800CB         // Haoyu with 4.3" or 5" (480x272)
+  //#define LCD_HAOYU_FT810CB         // Haoyu with 5" (800x480)
+  //#define LCD_ALEPHOBJECTS_CLCD_UI  // Aleph Objects Color LCD UI
+
+  // Correct the resolution if not using the stock TFT panel.
+  //#define TOUCH_UI_320x240
+  //#define TOUCH_UI_480x272
+  //#define TOUCH_UI_800x480
+
+  // Mappings for boards with a standard RepRapDiscount Display connector
+  //#define AO_EXP1_PINMAP    // AlephObjects CLCD UI EXP1 mapping
+  //#define AO_EXP2_PINMAP    // AlephObjects CLCD UI EXP2 mapping
+  //#define CR10_TFT_PINMAP   // Rudolph Riedel's CR10 pin mapping
+  //#define OTHER_PIN_LAYOUT  // Define pins manually below
+  #if ENABLED(OTHER_PIN_LAYOUT)
+    // The pins for CS and MOD_RESET (PD) must be chosen.
+    #define CLCD_MOD_RESET  9
+    #define CLCD_SPI_CS    10
+
+    // If using software SPI, specify pins for SCLK, MOSI, MISO
+    //#define CLCD_USE_SOFT_SPI
+    #if ENABLED(CLCD_USE_SOFT_SPI)
+      #define CLCD_SOFT_SPI_MOSI 11
+      #define CLCD_SOFT_SPI_MISO 12
+      #define CLCD_SOFT_SPI_SCLK 13
+    #endif
+  #endif
+
+  // Display Orientation. An inverted (i.e. upside-down) display
+  // is supported on the FT800. The FT810 and beyond also support
+  // portrait and mirrored orientations.
+  //#define TOUCH_UI_INVERTED
+  //#define TOUCH_UI_PORTRAIT
+  //#define TOUCH_UI_MIRRORED
+
+  // Use a numeric passcode for "Screen lock" keypad.
+  // (recommended for smaller displays)
+  //#define TOUCH_UI_PASSCODE
+#endif
+
 // @section safety
 
 /**

diff --git a/Marlin/src/HAL/HAL_DUE/fastio_Due.h b/Marlin/src/HAL/HAL_DUE/fastio_Due.h
@@ -70,7 +70,7 @@
   const uint32_t mask = MASK(DIO ## IO ## _PIN); \
   if (V) port->PIO_SODR = mask; \
   else port->PIO_CODR = mask; \
-} while(0)
+}while(0)
 
 // Toggle a pin
 #define _TOGGLE(IO) _WRITE(IO, !READ(IO))

diff --git a/Marlin/src/HAL/HAL_DUE/usb/compiler.h b/Marlin/src/HAL/HAL_DUE/usb/compiler.h
@@ -112,7 +112,7 @@
  * \def unused
  * \brief Marking \a v as a unused parameter or value.
  */
-#define unused(v)          do { (void)(v); } while(0)
+#define unused(v)          do { (void)(v); }while(0)
 
 /**
  * \def barrier
@@ -169,7 +169,7 @@
  * heuristics and inline the function no matter how big it thinks it
  * becomes.
  */
-#if defined(__CC_ARM)
+#ifdef __CC_ARM
 #   define __always_inline   __forceinline
 #elif (defined __GNUC__)
 #ifdef __always_inline
@@ -187,7 +187,7 @@
  * This annotation instructs the compiler to ignore its inlining
  * heuristics and not inline the function.
  */
-#if defined(__CC_ARM)
+#ifdef __CC_ARM
 #   define __no_inline   __attribute__((noinline))
 #elif (defined __GNUC__)
 #	define __no_inline   __attribute__((__noinline__))
@@ -204,7 +204,7 @@
  *
  * \param expr  Expression to evaluate and supposed to be nonzero.
  */
-#if defined(_ASSERT_ENABLE_)
+#ifdef _ASSERT_ENABLE_
 #  if defined(TEST_SUITE_DEFINE_ASSERT_MACRO)
      // Assert() is defined in unit_test/suite.h
 #    include "unit_test/suite.h"
@@ -998,14 +998,14 @@ typedef U8                  Byte;       //!< 8-bit unsigned integer.
 #endif  // #ifndef __ASSEMBLY__
 
 
-#if defined(__ICCARM__)
+#ifdef __ICCARM__
 #define SHORTENUM           __packed
 #elif defined(__GNUC__)
 #define SHORTENUM           __attribute__((packed))
 #endif
 
 /* No operation */
-#if defined(__ICCARM__)
+#ifdef __ICCARM__
 #define nop()               __no_operation()
 #elif defined(__GNUC__)
 #define nop()               (__NOP())

diff --git a/Marlin/src/HAL/HAL_LINUX/include/serial.h b/Marlin/src/HAL/HAL_LINUX/include/serial.h
@@ -142,10 +142,10 @@ class HalSerial {
   void print_bin(uint32_t value, uint8_t num_digits) {
     uint32_t mask = 1 << (num_digits -1);
     for (uint8_t i = 0; i < num_digits; i++) {
-      if (!(i % 4) && i)    write(' ');
-      if (!(i % 16)  && i)  write(' ');
-      if (value & mask)     write('1');
-      else                  write('0');
+      if (!(i %  4) && i) write(' ');
+      if (!(i % 16) && i) write(' ');
+      if (value & mask)   write('1');
+      else                write('0');
       value <<= 1;
     }
   }

diff --git a/Marlin/src/HAL/HAL_SAMD51/Servo_SAMD51.cpp b/Marlin/src/HAL/HAL_SAMD51/Servo_SAMD51.cpp
@@ -115,12 +115,12 @@ HAL_SERVO_TIMER_ISR() {
       tc->COUNT16.CC[tcChannel].reg = (uint16_t)(tcCounterValue - 4UL);               // at least REFRESH_INTERVAL has elapsed
   }
   if (tcChannel == 0) {
-    SYNC(tc->COUNT16.SYNCBUSY.bit.CC0); 
+    SYNC(tc->COUNT16.SYNCBUSY.bit.CC0);
     // Clear the interrupt
     tc->COUNT16.INTFLAG.reg = TC_INTFLAG_MC0;
   }
   else {
-    SYNC(tc->COUNT16.SYNCBUSY.bit.CC1); 
+    SYNC(tc->COUNT16.SYNCBUSY.bit.CC1);
     // Clear the interrupt
     tc->COUNT16.INTFLAG.reg = TC_INTFLAG_MC1;
   }

diff --git a/Marlin/src/HAL/HAL_STM32/fastio_STM32.h b/Marlin/src/HAL/HAL_STM32/fastio_STM32.h
@@ -53,7 +53,7 @@ void FastIO_init(); // Must be called before using fast io macros
   #define _WRITE(IO, V) do { \
     if (V) FastIOPortMap[STM_PORT(digitalPin[IO])]->BSRR = _BV32(STM_PIN(digitalPin[IO])) ; \
     else   FastIOPortMap[STM_PORT(digitalPin[IO])]->BRR  = _BV32(STM_PIN(digitalPin[IO])) ; \
-  } while(0)
+  }while(0)
 #else
   #define _WRITE(IO, V) (FastIOPortMap[STM_PORT(digitalPin[IO])]->BSRR = _BV32(STM_PIN(digitalPin[IO]) + (V ? 0 : 16)))
 #endif

diff --git a/Marlin/src/HAL/HAL_STM32F1/fastio_STM32F1.h b/Marlin/src/HAL/HAL_STM32F1/fastio_STM32F1.h
@@ -38,8 +38,8 @@
 #define _SET_OUTPUT(IO)       _SET_MODE(IO, GPIO_OUTPUT_PP)
 #define _SET_OUTPUT_OD(IO)    _SET_MODE(IO, GPIO_OUTPUT_OD)
 
-#define OUT_WRITE(IO,V)       do{ _SET_OUTPUT(IO); WRITE(IO,V); } while(0)
-#define OUT_WRITE_OD(IO,V)    do{ _SET_OUTPUT_OD(IO); WRITE(IO,V); } while(0)
+#define OUT_WRITE(IO,V)       do{ _SET_OUTPUT(IO); WRITE(IO,V); }while(0)
+#define OUT_WRITE_OD(IO,V)    do{ _SET_OUTPUT_OD(IO); WRITE(IO,V); }while(0)
 
 #define SET_INPUT(IO)         _SET_MODE(IO, GPIO_INPUT_FLOATING)
 #define SET_INPUT_PULLUP(IO)  _SET_MODE(IO, GPIO_INPUT_PU)

diff --git a/Marlin/src/core/macros.h b/Marlin/src/core/macros.h
@@ -118,24 +118,24 @@
   // Using GCC extensions, but Travis GCC version does not like it and gives
   //  "error: statement-expressions are not allowed outside functions nor in template-argument lists"
   #define NOLESS(v, n) \
-    do { \
+    do{ \
       __typeof__(n) _n = (n); \
       if (v < _n) v = _n; \
-    } while(0)
+    }while(0)
 
   #define NOMORE(v, n) \
-    do { \
+    do{ \
       __typeof__(n) _n = (n); \
       if (v > _n) v = _n; \
-    } while(0)
+    }while(0)
 
   #define LIMIT(v, n1, n2) \
-    do { \
+    do{ \
       __typeof__(n1) _n1 = (n1); \
       __typeof__(n2) _n2 = (n2); \
       if (v < _n1) v = _n1; \
       else if (v > _n2) v = _n2; \
-    } while(0)
+    }while(0)
 
 #endif
 

diff --git a/Marlin/src/core/serial.h b/Marlin/src/core/serial.h
@@ -184,5 +184,5 @@ void print_bin(const uint16_t val);
 
 void print_xyz(PGM_P const prefix, PGM_P const suffix, const float x, const float y, const float z);
 void print_xyz(PGM_P const prefix, PGM_P const suffix, const float xyz[]);
-#define SERIAL_POS(SUFFIX,VAR) do { print_xyz(PSTR("  " STRINGIFY(VAR) "="), PSTR(" : " SUFFIX "\n"), VAR); } while(0)
-#define SERIAL_XYZ(PREFIX,V...) do { print_xyz(PSTR(PREFIX), nullptr, V); } while(0)
+#define SERIAL_POS(SUFFIX,VAR) do { print_xyz(PSTR("  " STRINGIFY(VAR) "="), PSTR(" : " SUFFIX "\n"), VAR); }while(0)
+#define SERIAL_XYZ(PREFIX,V...) do { print_xyz(PSTR(PREFIX), nullptr, V); }while(0)
diff --git a/Marlin/src/feature/leds/leds.cpp b/Marlin/src/feature/leds/leds.cpp
@@ -125,7 +125,7 @@ void LEDLights::set_color(const LEDColor &incol
     // If the pins can do PWM then their intensity will be set.
     #define UPDATE_RGBW(C,c) do { if (PWM_PIN(RGB_LED_##C##_PIN)) \
         analogWrite(pin_t(RGB_LED_##C##_PIN), incol.c); \
-      else WRITE(RGB_LED_##C##_PIN, incol.c ? HIGH : LOW); } while(0)
+      else WRITE(RGB_LED_##C##_PIN, incol.c ? HIGH : LOW); }while(0)
     UPDATE_RGBW(R,r);
     UPDATE_RGBW(G,g);
     UPDATE_RGBW(B,b);

diff --git a/Marlin/src/gcode/calibrate/G33.cpp b/Marlin/src/gcode/calibrate/G33.cpp
@@ -445,7 +445,7 @@ void GcodeSuite::G33() {
              _tower_results       = (_4p_calibration && towers_set) || probe_points >= 3,
              _opposite_results    = (_4p_calibration && !towers_set) || probe_points >= 3,
              _endstop_results     = probe_points != 1 && probe_points != -1 && probe_points != 0,
-             _angle_results       = probe_points >= 3  && towers_set;
+             _angle_results       = probe_points >= 3 && towers_set;
   static const char save_message[] PROGMEM = "Save with M500 and/or copy to Configuration.h";
   int8_t iterations = 0;
   float test_precision,

diff --git a/Marlin/src/gcode/calibrate/G34_M422.cpp b/Marlin/src/gcode/calibrate/G34_M422.cpp
@@ -284,7 +284,7 @@ void GcodeSuite::G34() {
     // Home Z after the alignment procedure
     process_subcommands_now_P(PSTR("G28 Z"));
 
-  } while(0);
+  }while(0);
 
   if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("<<< G34");
 }

diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h
@@ -368,7 +368,7 @@
 #endif
 
 // Extensible UI serial touch screens. (See src/lcd/extensible_ui)
-#if EITHER(MALYAN_LCD, DGUS_LCD)
+#if ANY(MALYAN_LCD, DGUS_LCD, LULZBOT_TOUCH_UI)
   #define IS_EXTUI
   #define EXTENSIBLE_UI
 #endif

diff --git a/Marlin/src/inc/Conditionals_adv.h b/Marlin/src/inc/Conditionals_adv.h
@@ -99,3 +99,6 @@
     #define LED_USER_PRESET_BRIGHTNESS 255
   #endif
 #endif
+
+// Extensible UI pin mapping for RepRapDiscount
+#define TOUCH_UI_ULTIPANEL ENABLED(LULZBOT_TOUCH_UI) && ANY(AO_EXP1_PINMAP, AO_EXP2_PINMAP, CR10_TFT_PINMAP)
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h
@@ -1892,6 +1892,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
   + ENABLED(OVERLORD_OLED) \
   + ENABLED(DGUS_LCD) \
   + ENABLED(MALYAN_LCD) \
+  + ENABLED(LULZBOT_TOUCH_UI) \
   + ENABLED(FSMC_GRAPHICAL_TFT)
   #error "Please select no more than one LCD controller option."
 #endif