✨ BigTreeTech Manta M4P, M5P, M8P V1.0 / 1.1, E3 EZ (#25001)

Marlin/src/pins/pins.h

@@ -545,6 +545,16 @@
   #include "stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h"  // STM32F1                              env:STM32F103RC_btt env:STM32F103RC_btt_USB env:STM32F103RE_btt env:STM32F103RE_btt_USB env:STM32F103RC_btt_maple env:STM32F103RC_btt_USB_maple env:STM32F103RE_btt_maple env:STM32F103RE_btt_USB_maple
 #elif MB(BTT_SKR_MINI_E3_V3_0)
   #include "stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h"  // STM32G0                              env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_M4P_V1_0)
+  #include "stm32g0/pins_BTT_MANTA_M4P_V1_0.h"    // STM32G0                              env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_M5P_V1_0)
+  #include "stm32g0/pins_BTT_MANTA_M5P_V1_0.h"    // STM32G0                              env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_E3_EZ_V1_0)
+  #include "stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h"  // STM32G0                              env:STM32G0B1RE_btt env:STM32G0B1RE_btt_xfer
+#elif MB(BTT_MANTA_M8P_V1_0)
+  #include "stm32g0/pins_BTT_MANTA_M8P_V1_0.h"    // STM32G0                              env:STM32G0B1VE_btt env:STM32G0B1VE_btt_xfer
+#elif MB(BTT_MANTA_M8P_V1_1)
+  #include "stm32g0/pins_BTT_MANTA_M8P_V1_1.h"    // STM32G0                              env:STM32G0B1VE_btt env:STM32G0B1VE_btt_xfer
 #elif MB(BTT_SKR_MINI_E3_V3_0_1)
   #include "stm32f4/pins_BTT_SKR_MINI_E3_V3_0_1.h"// STM32F4                              env:STM32F401RC_btt
 #elif MB(BTT_SKR_MINI_MZ_V1_0)

Marlin/src/pins/stm32g0/env_validate.h

@@ -0,0 +1,26 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+#if NOT_TARGET(STM32G0xx) || NOT_TARGET(STM32G0B1xx)
+  #error "Oops! Select an STM32G0 board in 'Tools > Board.'"
+#endif

Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h

@@ -21,6 +21,8 @@
  */
 #pragma once
 
+#include "env_validate.h"
+
 /** CAUTION **
  * This board definition is to facilitate support for a Filament Extrusion
  * devices, used to convert waste plastic into 3D printable filament.

Marlin/src/pins/stm32g0/pins_BTT_MANTA_E3_EZ_V1_0.h

@@ -0,0 +1,340 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+#include "env_validate.h"
+
+#ifndef BOARD_INFO_NAME
+  #define BOARD_INFO_NAME "BTT Manta E3 EZ V1.0"
+#endif
+
+#define USES_DIAG_JUMPERS
+
+// Ignore temp readings during development.
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
+
+//
+// EEPROM
+//
+#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
+  #undef NO_EEPROM_SELECTED
+  #ifndef FLASH_EEPROM_EMULATION
+    #define FLASH_EEPROM_EMULATION
+  #endif
+  #define EEPROM_PAGE_SIZE      (0x800UL) // 2K
+  #define EEPROM_START_ADDRESS  (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
+  #define MARLIN_EEPROM_SIZE    EEPROM_PAGE_SIZE
+#endif
+
+//
+// Servos
+//
+#define SERVO0_PIN                          PA7   // BLTouch
+
+//
+// Probe enable
+//
+#if ENABLED(PROBE_ENABLE_DISABLE)
+  #ifndef PROBE_ENABLE_PIN
+    #define PROBE_ENABLE_PIN          SERVO0_PIN
+  #endif
+#endif
+
+//
+// Trinamic StallGuard pins
+//
+#define X_DIAG_PIN                          PC4   // X-STOP
+#define Y_DIAG_PIN                          PB0   // Y-STOP
+#define Z_DIAG_PIN                          PC6   // Z-STOP
+#define E0_DIAG_PIN                         PC5   // E0-DET
+#define E1_DIAG_PIN                         PB1   // E1-DET
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN                    X_DIAG_PIN  // X-STOP
+#define Y_STOP_PIN                    Y_DIAG_PIN  // Y-STOP
+#define Z_STOP_PIN                    Z_DIAG_PIN  // Z-STOP
+
+//
+// Z Probe (when not Z_STOP_PIN)
+//
+#define Z_MIN_PROBE_PIN                     PA6   // BLTouch
+
+//
+// Filament Runout Sensor
+//
+#ifndef FIL_RUNOUT_PIN
+  #define FIL_RUNOUT_PIN             E0_DIAG_PIN  // E0-DET
+#endif
+#ifndef FIL_RUNOUT2_PIN
+  #define FIL_RUNOUT2_PIN            E1_DIAG_PIN  // E1-DET
+#endif
+
+//
+// Power Supply Control
+//
+#ifndef PS_ON_PIN
+  #define PS_ON_PIN                         PA9   // PS-ON
+#endif
+
+//
+// Power Loss Detection
+//
+#ifndef POWER_LOSS_PIN
+  #define POWER_LOSS_PIN                    PB9   // PWRDET
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN                          PA14
+#define X_DIR_PIN                           PA10
+#define X_ENABLE_PIN                        PA13
+#ifndef X_CS_PIN
+  #define X_CS_PIN                          PB8
+#endif
+
+#define Y_STEP_PIN                          PC8
+#define Y_DIR_PIN                           PA15
+#define Y_ENABLE_PIN                        PC14
+#ifndef Y_CS_PIN
+  #define Y_CS_PIN                          PC9
+#endif
+
+#define Z_STEP_PIN                          PD2
+#define Z_DIR_PIN                           PD4
+#define Z_ENABLE_PIN                        PD3
+#ifndef Z_CS_PIN
+  #define Z_CS_PIN                          PD0
+#endif
+
+#define E0_STEP_PIN                         PD5
+#define E0_DIR_PIN                          PD6
+#define E0_ENABLE_PIN                       PB3
+#ifndef E0_CS_PIN
+  #define E0_CS_PIN                         PD1
+#endif
+
+#define E1_STEP_PIN                         PB7
+#define E1_DIR_PIN                          PB6
+#define E1_ENABLE_PIN                       PB4
+#ifndef E1_CS_PIN
+  #define E1_CS_PIN                         PB5
+#endif
+
+//
+// Software SPI pins for TMC2130 stepper drivers
+//
+#if ENABLED(TMC_USE_SW_SPI)
+  #ifndef TMC_SW_MOSI
+    #define TMC_SW_MOSI                     PC12  // Shared with SPI header, Pin 5 (SPI3)
+  #endif
+  #ifndef TMC_SW_MISO
+    #define TMC_SW_MISO                     PC11  // Shared with SPI header, Pin 6 (SPI3)
+  #endif
+  #ifndef TMC_SW_SCK
+    #define TMC_SW_SCK                      PC10  // Shared with SPI header, Pin 4 (SPI3)
+  #endif
+#endif
+
+#if HAS_TMC_UART
+  #define X_SERIAL_TX_PIN                   PB8   // X_CS_PIN
+  #define X_SERIAL_RX_PIN        X_SERIAL_TX_PIN
+
+  #define Y_SERIAL_TX_PIN                   PC9   // Y_CS_PIN
+  #define Y_SERIAL_RX_PIN        Y_SERIAL_TX_PIN
+
+  #define Z_SERIAL_TX_PIN                   PD0   // Z_CS_PIN
+  #define Z_SERIAL_RX_PIN        Z_SERIAL_TX_PIN
+
+  #define E0_SERIAL_TX_PIN                  PD1   // E0_CS_PIN
+  #define E0_SERIAL_RX_PIN      E0_SERIAL_TX_PIN
+
+  #define E1_SERIAL_TX_PIN                  PB5   // E1_CS_PIN
+  #define E1_SERIAL_RX_PIN      E1_SERIAL_TX_PIN
+
+  // Reduce baud rate to improve software serial reliability
+  #define TMC_BAUD_RATE                    19200
+#endif
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN                          PA4   // Analog Input "TH0"
+#define TEMP_1_PIN                          PA5   // Analog Input "TH1"
+#define TEMP_BED_PIN                        PA3   // Analog Input "TB"
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN                        PB11  // "HE0"
+#define HEATER_1_PIN                        PB10  // "HE1"
+#define HEATER_BED_PIN                      PB2   // "HB"
+
+#define FAN_PIN                             PA8   // "FAN0"
+#define FAN1_PIN                            PB15  // "FAN1"
+#define FAN2_PIN                            PB14  // "FAN2"
+
+//
+// Auto fans
+//
+#if HOTENDS == 2
+  #ifndef E0_AUTO_FAN_PIN
+    #define E0_AUTO_FAN_PIN             FAN1_PIN
+  #endif
+  #ifndef E1_AUTO_FAN_PIN
+    #define E1_AUTO_FAN_PIN             FAN2_PIN
+  #endif
+#else
+  #ifndef E0_AUTO_FAN_PIN
+    #define E0_AUTO_FAN_PIN             FAN1_PIN
+  #endif
+  #ifndef CONTROLLER_FAN_PIN
+    #define CONTROLLER_FAN_PIN          FAN2_PIN
+  #endif
+#endif
+
+/**
+ *           Manta E3 EZ V1.0
+ *                ------
+ * (BEEPER)  PC1 | 1  2 | PC2  (BTN_ENC)
+ * (BTN_EN1) PC3 | 3  4 | RESET
+ * (BTN_EN2) PC0   5  6 | PA0  (LCD_D4)
+ * (LCD_RS)  PA2 | 7  8 | PA1  (LCD_EN)
+ *           GND | 9 10 | 5V
+ *                ------
+ *                 EXP1
+ */
+#define EXP1_01_PIN                         PC1
+#define EXP1_02_PIN                         PC2
+#define EXP1_03_PIN                         PC3
+#define EXP1_04_PIN                         -1
+#define EXP1_05_PIN                         PC0
+#define EXP1_06_PIN                         PA0
+#define EXP1_07_PIN                         PA2
+#define EXP1_08_PIN                         PA1
+#define EXP1_09_PIN                         -1
+#define EXP1_10_PIN                         -1
+
+#if HAS_DWIN_E3V2 || IS_DWIN_MARLINUI
+  #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING
+    #error "CAUTION! Ender-3 V2 display requires a custom cable with TX = PA0, RX = PC2. See 'pins_BTT_MANTA_E3_EZ_V1_0.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)"
+  #endif
+
+ /**
+  *            Ender-3 V2 display                        Manta E3 EZ V1.0               Ender-3 V2 display --> Manta E3 EZ V1.0
+  *                  ------                                   ------                                 RX  3 -->  5  P0_15
+  *             --  | 1  2 | --                (BEEPER)  PC1 | 1  2 | PC2  (BTN_ENC)                 TX  4 -->  9  P0_16
+  * (MANTA TX1) RX  | 3  4 | TX (MANTA RX1)    (BTN_EN1) PC3 | 3  4 | RESET                      BEEPER  6 --> 10  P2_08
+  *   (BTN_ENC) ENT   5  6 | BEEPER            (BTN_EN2) PC0   5  6 | PA0  (LCD_D4)
+  *   (BTN_E2)  B   | 7  8 | A  (BTN_E1)       (LCD_RS)  PA2 | 7  8 | PA1  (LCD_EN)
+  *             GND | 9 10 | 5V                          GND | 9 10 | 5V
+  *                  ------                                   ------
+  */
+
+  #define BEEPER_PIN                 EXP1_01_PIN
+  #define BTN_EN1                    EXP1_08_PIN
+  #define BTN_EN2                    EXP1_07_PIN
+  #define BTN_ENC                    EXP1_05_PIN
+
+#elif HAS_WIRED_LCD
+
+  #if ENABLED(CR10_STOCKDISPLAY)
+
+    #define BEEPER_PIN               EXP1_01_PIN
+
+    #define BTN_EN1                  EXP1_03_PIN
+    #define BTN_EN2                  EXP1_05_PIN
+    #define BTN_ENC                  EXP1_02_PIN
+
+    #define LCD_PINS_RS              EXP1_07_PIN
+    #define LCD_PINS_ENABLE          EXP1_08_PIN
+    #define LCD_PINS_D4              EXP1_06_PIN
+
+  #elif ENABLED(ZONESTAR_LCD)                     // ANET A8 LCD Controller - Must convert to 3.3V - CONNECTING TO 5V WILL DAMAGE THE BOARD!
+
+    #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING
+      #error "CAUTION! ZONESTAR_LCD requires wiring modifications. See 'pins_BTT_MANTA_E3_EZ_V1_0.h' for details. (Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning.)"
+    #endif
+
+    #define LCD_PINS_RS              EXP1_06_PIN
+    #define LCD_PINS_ENABLE          EXP1_02_PIN
+    #define LCD_PINS_D4              EXP1_07_PIN
+    #define LCD_PINS_D5              EXP1_05_PIN
+    #define LCD_PINS_D6              EXP1_03_PIN
+    #define LCD_PINS_D7              EXP1_01_PIN
+    #define ADC_KEYPAD_PIN                  PA7   // Repurpose default SERVO0_PIN for ADC - CONNECTING TO 5V WILL DAMAGE THE BOARD!
+
+  #elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
+
+    #define BTN_EN1                  EXP1_03_PIN
+    #define BTN_EN2                  EXP1_05_PIN
+    #define BTN_ENC                  EXP1_02_PIN
+
+    #define DOGLCD_CS                EXP1_07_PIN
+    #define DOGLCD_A0                EXP1_06_PIN
+    #define DOGLCD_SCK               EXP1_01_PIN
+    #define DOGLCD_MOSI              EXP1_08_PIN
+    #define FORCE_SOFT_SPI
+    #define LCD_BACKLIGHT_PIN               -1
+
+  #else
+
+    #error "Only ZONESTAR_LCD, MKS_MINI_12864, ENDER2_STOCKDISPLAY, and CR10_STOCKDISPLAY are currently supported on the BTT_MANTA_E3_EZ_V1_0."
+
+  #endif
+
+#endif // HAS_WIRED_LCD
+
+//
+// SD Support
+//
+
+#ifndef SDCARD_CONNECTION
+  #define SDCARD_CONNECTION              ONBOARD
+#endif
+
+#define SD_DETECT_PIN                       -1
+
+#if SD_CONNECTION_IS(LCD) && (BOTH(TOUCH_UI_FTDI_EVE, LCD_FYSETC_TFT81050) || IS_TFTGLCD_PANEL)
+  #define SD_SS_PIN                  EXP1_05_PIN
+#elif SD_CONNECTION_IS(CUSTOM_CABLE)
+  #error "SD CUSTOM_CABLE is not compatible with Manta E3 EZ."
+#endif
+
+#define ONBOARD_SPI_DEVICE                     3  // SPI3 -> used only by HAL/STM32F1...
+#define ONBOARD_SD_CS_PIN                   PC13  // Chip select for "System" SD card
+
+#define ENABLE_SPI3
+#define SDSS                   ONBOARD_SD_CS_PIN
+#define SD_SS_PIN              ONBOARD_SD_CS_PIN
+#define SD_SCK_PIN                          PC10
+#define SD_MISO_PIN                         PC11
+#define SD_MOSI_PIN                         PC12
+
+//
+// NeoPixel LED
+//
+#ifndef NEOPIXEL_PIN
+  #define NEOPIXEL_PIN                      PC7   // RGB
+#endif