Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Probe_Offset_Wizard: Improvements #20239

Merged

Conversation

swissnorp
Copy link
Contributor

Requirements

  • Filling out this template is required. Pull Requests without a clear description may be closed at the maintainers' discretion.

Description

Config

  • Now it's possible to disable PROBE_OFFSET_START and use current probe.offset.z instead
  • The set PROBE_OFFSET_WIZARD_XY_POS will be used for probing a z_offset_ref and for the nozzle/bed contact position (the nozzle will move to this position after probing).

Procedure

  1. Call Wizard by user
  2. Store current probe.offset.z for backup and overwrite it with PROBE_OFFSET_START if defined
  3. Store Bed-Leveling-State and deactivate it
  4. Home all Axes by G28
  5. Call Preparation
  6. Disable Soft Endstops
  7. Set z_offset_ref = 0 (for if homing is done by probe and PROBE_OFFSET_WIZARD_XY_POS is not ##defined)
  8. If Probe is not used for homing or PROBE_OFFSET_WIZARD_XY_POS is defined, z_offset_ref must be probed
  9. If PROBE_OFFSET_WIZARD_XY_POS is not defined probing will be done at XY_CENTER
  10. The Nozzle moves by the probe.offset_xy to the Probing point
  11. Call Menu
  12. The probed will be used to calculate the new probe.offset.z: calculated_z_offset = probe.offset.z + current_position.z - z_offset_ref
  13. User adjust Offset by menu
  14. Done by user
  15. The calulated Offset is stored
  16. If Probe is used for homing, homing is done with the new offset.
  17. Cancel by user
  18. The old Offset is restored
  19. If Probe is used for homing and PROBE_OFFSET_START is set, homing is done with the restored offset.

Benefits

  • Its possible to calibrate the probe offset even if its not used for homing.
  • The calibration is accurate because probing and nozzle/bed-contact points are the same
  • Its possible to define a specific position for the calibration wizard

Configurations

Niente

Related Issues

#19650
#20204

@qwewer0
Copy link
Contributor

qwewer0 commented Nov 21, 2020

This fixed the issue 4-6 in #20204 (comment), but it still goes back to the status screen.

Add ui.defer_status_screen(); in top of goto_probe_offset_wizard()
@swissnorp
Copy link
Contributor Author

swissnorp commented Nov 21, 2020

This fixed the issue 4-6 in #20204 (comment), but it still goes back to the status screen.

@qwewer0 Thank you for your quick test! I could reproduce your problem. If homing takes to long (nozzle far away from endstop) it falls back to the status screen.

I think the latest commit fixed it. Could you give it another try?

Thanks, norp

@qwewer0
Copy link
Contributor

qwewer0 commented Nov 22, 2020

Tried it with the new changes:
Now after homing it probes the bed (Z reference) one more times (3 times with MULTIPLE_PROBING 2, EXTRA_PROBING 1) while the LCD shows nothing (blank), then it moves to PROBE_OFFSET_WIZARD_XY_POS and goes into the wizard menu and can be used as before.

  • I would love to see an LCD message while it probes for the Z reference, so that it isn't just a blank screen.
  • And one thing that I don't like, is the homing after the done/cancel button. Is there a particular reason why do we need to home after the wizard?

@filippor
Copy link
Contributor

Tested on a delta and it seems to work with PROBE_OFFSET_WIZARD_XY_POS uncommented

@swissnorp
Copy link
Contributor Author

@qwewer0

  • I would love to see an LCD message while it probes for the Z reference, so that it isn't just a blank screen.

This is fixed now.
I added a message screen when probing the Z Reference: Probing Z Reference.
And an other one for the moving part: Moving to Probing Pos

  • And one thing that I don't like, is the homing after the done/cancel button. Is there a particular reason why do we need to home after the wizard?

Yes its absolutely needed. If you don't believe me, try it by uncommenting it 😸. The current_position.z would not be trustable any more under the given sircumstances/if-conditions. But I reduced it to home Z only.

@thinkyhead
As a cherry on top it would be great if we could extend the messages for homing in marlin so it would be easy to give proper screens:
MSG_LEVEL_BED_HOMING = _UxGT("Homing XYZ");
MSG_LEVEL_BED_HOMING_XY = _UxGT("Homing XY");
MSG_LEVEL_BED_HOMING_Z = _UxGT("Homing Z");

@filippor Thank you for testing and giving a feedback 👍

I think the code is not perfect but it works. I am relatively new to marlin and I never proberly learned to code 😅. Maybe there is some clean up possible.

Enjoy Testing, norp

@qwewer0
Copy link
Contributor

qwewer0 commented Nov 24, 2020

But I reduced it to home Z only.

That is the same as it was for probe users.

Why can't do_z_clearance(); be used after the wizard? I changed queue.inject_P(PSTR("G28Z")); to do_z_clearance(20.0); and it worked just fine.

In my opinion a homing after the wizard is inconvenient (if it isn't absolutely needed), but a z clearance is absolutely needed, because of a possible heated nozzle.

Sorry if I'm missing something.

@qwewer0
Copy link
Contributor

qwewer0 commented Nov 24, 2020

Would it not work?

ACTION_ITEM(MSG_BUTTON_DONE, []{
    set_offset_and_go_back(calculated_z_offset);
    do_z_clearance(20.0);
  });

ACTION_ITEM(MSG_BUTTON_CANCEL, []{
    set_offset_and_go_back(z_offset_backup);
    do_z_clearance(20.0);
  });

@swissnorp
Copy link
Contributor Author

@qwewer0 Thank you for partizipation. I realy apreciate your skepsis.

Sorry if I'm missing something.

Yep you are 😉 .
Homing for the wizard was done with PROBE_OFFSET_START or with (let's expext) wrong probe.offset.z. Changing or resetting the probe.offset.z to the proper value does not change current_position.z!

So rehoming Z is absolutely needed!

Would it not work?

ACTION_ITEM(MSG_BUTTON_DONE, []{
    set_offset_and_go_back(calculated_z_offset);
    do_z_clearance(20.0);
  });

ACTION_ITEM(MSG_BUTTON_CANCEL, []{
    set_offset_and_go_back(z_offset_backup);
    do_z_clearance(20.0);
  });

NO 😏

Did you measure the distance between nozzle and bed, and did it match with the current_position.z?
Make sure that PROBE_OFFSET_START or your currently set probe.offset.z (from Settings/EEPROM) is more than 1 mm off from
your proper/real probe.offset.z, and measure with a ruler!

Adios, norp

@qwewer0
Copy link
Contributor

qwewer0 commented Nov 24, 2020

Tested it with do_z_clearance(20.0);, and after the wizard the LCD showed 20, and the nozzle was at 18.75 with a z offset of -1.25.

Despite all this, I still believe that it should only move the z axis up a little for clearance, and either disengage the steppers or just set the z axis or all to be unhomed/untrusted.
Edit: With perfect z offset before the wizard.

@swissnorp
Copy link
Contributor Author

Tested it with do_z_clearance(20.0);, and after the wizard the LCD showed 20, and the nozzle was at 18.75 with a z offset of -1.25.

Despite all this, I still believe that it should only move the z axis up a little for clearance, and either disengage the steppers or just set the z axis or all to be unhomed/untrusted.
Edit: With perfect z offset before the wizard.

But you have had enabled PROBE_OFFSET_START with a different value, haven't you? And thats the reason for me to rehome (or to set Z-Axis untrusted, as you mentioned).

Conclusion:

  • So we have different opinions about homing after the wizard. I vote for rehoming, because I think it's safer and more convenient. And there are several newer and older features, which do a rehoming after a calibration process. I leave it in there!
  • But nevertheless I think about adding a do_z_clearance(Z); indepentently.
  • I will also add a SanityCheck to check if PROBE_OFFSET_START or NOZZLE_TO_PROBE_OFFSET.Z, because the Probe will never trigger at a higher point as the nozzle!

I will work on it tomorrow night (MEZ/CET).

Good night, norp

@qwewer0
Copy link
Contributor

qwewer0 commented Nov 24, 2020

If the homing wins, then I'm 100% with it.
And for the a Z clearance after the homing, I think it definitely needs a bit (10-20 mm) of a Z clearance even after the homing, because while the Z_CLEARANCE_DEPLOY_PROBE could be big enough, like with a BLTouch setup, but it might be too small with an inductive or laser probe, and we don't want accidental heated bed burning with the wizard, do we?

@swissnorp
Copy link
Contributor Author

If the homing wins, then I'm 100% with it.
And for the a Z clearance after the homing, I think it definitely needs a bit (10-20 mm) of a Z clearance even after the homing, because while the Z_CLEARANCE_DEPLOY_PROBE could be big enough, like with a BLTouch setup, but it might be too small with an inductive or laser probe, and we don't want accidental heated bed burning with the wizard, do we?

I think you are meaning do_z_clearance(Z); before homing, aren't you? After homing it would make absolutely no sens!?

@thinkyhead
Copy link
Member

We have Z_AFTER_HOMING to set the desired raise after G28 is complete.

@swissnorp
Copy link
Contributor Author

swissnorp commented Nov 24, 2020

@thinkyhead yes excactly

Conclusion:

* So we have different opinions about homing after the wizard. I vote for rehoming, because I think it's safer and more convenient. And there are several newer and older features, which do a rehoming after a calibration process. I leave it in there!

* But nevertheless I think about adding a `do_z_clearance(Z);` indepentently.

* I will also add a `SanityCheck` to check if `PROBE_OFFSET_START` or `NOZZLE_TO_PROBE_OFFSET.Z`, because the Probe will never trigger at a higher point as the nozzle!

SanityCheck still has to be done.

For the rest, I did it like this:

  ACTION_ITEM(MSG_BUTTON_DONE, []{
    set_offset_and_go_back(calculated_z_offset);

    // Set Z to 0, as we can expect
    current_position.z = 0;
    planner.sync_plan_position();

    // Raise Z as if it was homed
    do_z_clearance(0
    #ifdef Z_AFTER_HOMING
      +Z_AFTER_HOMING
    #elseif defined(Z_HOMING_HEIGHT)
      +Z_HOMING_HEIGHT
    #endif
    );
  });

  ACTION_ITEM(MSG_BUTTON_CANCEL, []{
    set_offset_and_go_back(z_offset_backup);

    // If wizard-homing was done with PROBE_OFFSET_WIZARD_START_Z by probe.
    // Set Z to 0 (if higher than 0) to be sure for G28 clearance and rehome Z with backed up offset.
    #if defined(PROBE_OFFSET_WIZARD_START_Z) && EITHER(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN, USE_PROBE_FOR_Z_HOMING)
      if(current_position.z > 0) { current_position.z = 0; planner.sync_plan_position(); }
      queue.inject_P(PSTR("G28Z"));

    // Otherwise do a Z clearance move like after Homing
    #else
      do_z_clearance(0
      #ifdef Z_AFTER_HOMING
        +Z_AFTER_HOMING
      #elseif defined(Z_HOMING_HEIGHT)
        +Z_HOMING_HEIGHT
      #endif
      );
    #endif
  });

Good Night, norp

Copy link
Contributor

@qwewer0 qwewer0 left a comment

Choose a reason for hiding this comment

The reason will be displayed to describe this comment to others. Learn more.

It should be safe even if Z_AFTER_HOMING and Z_HOMING_HEIGHT isn't defined, and move the nozzle up at the end.

Marlin/src/lcd/menu/menu_probe_offset.cpp Outdated Show resolved Hide resolved
@thinkyhead thinkyhead merged commit 649965a into MarlinFirmware:bugfix-2.0.x Nov 26, 2020
Minims pushed a commit to Minims/Marlin that referenced this pull request Nov 26, 2020
@swissnorp swissnorp deleted the ProbeOffsetWizard-Improvements branch November 27, 2020 19:55
@ohrn
Copy link

ohrn commented Dec 1, 2020

Hi!

This sanity check addition breaks compilation on my printer, a ZYYX Pro.

    static_assert(sanity_nozzle_to_probe_offset.z <= 0.25,
                  "Are you sure your Probe triggers above the nozzle? Set a negative Z value in the NOZZLE_TO_PROBE_OFFSET.");

The probe truly triggers 2 mm "above" the nozzle. The printer has a micro switch next to the nozzle and notches cut out of the build plate edges. When probing the nozzle lowers into a notch and the switch engages on the plate.

Z safe probing and carefully defined probe points matching the notches is a must on this printer! 😄

I guess this is not a common design, but it would be nice if this error could be turned into a warning, or another "I really know what I'm doing" config added to allow a positive z offset.

/Fredrik

@swissnorp
Copy link
Contributor Author

@ohrn Thats some crazy endstop mount 😄 .
Could you test 9702170 and give some feedback? Make sure you enable/uncomment NOZZLE_TO_PROBE_OFFSET_Z_POSITIVE.

Thanks for your input.

@swissnorp swissnorp restored the ProbeOffsetWizard-Improvements branch December 2, 2020 21:12
@swissnorp swissnorp deleted the ProbeOffsetWizard-Improvements branch December 2, 2020 21:14
Kannix2005 pushed a commit to Kannix2005/Marlin-1 that referenced this pull request Dec 7, 2020
vgadreau pushed a commit to vgadreau/Marlin that referenced this pull request Dec 9, 2020
RFBomb pushed a commit to RFBomb/Marlin that referenced this pull request Dec 23, 2020
TheMichalcinOfficial added a commit to TheMichalcinOfficial/Marlin that referenced this pull request Dec 28, 2020
* USB Media Host followup

Restore HAS_SHARED_MEDIA

* SMUFF (MMU2 clone) support (MarlinFirmware#19912)

* [cron] Bump distribution date (2020-11-19)

* Fix broken #include (MarlinFirmware#20193)

* Use RTD for MAX31865 reading (MarlinFirmware#20188)

* Abort print on media removal (MarlinFirmware#20200)

* Fix Filament Change menu item labels (MarlinFirmware#20201)

* Remaining Time followup (MarlinFirmware#20199)

* Fix GTR NeoPixel pin with FYSETC Mini12864 (MarlinFirmware#20203)

* Reduce RAM usage for TFT Color UI on SGen-L V2 (MarlinFirmware#20209)

* Add Thermistor 20-21 notes (MarlinFirmware#19246)

* MKS WiFi preliminary changes

* More MKS WiFi

* MKS WiFi strings

* Fix Z label

* Windows LPC Upload for non-admins (MarlinFirmware#20208)

Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix DAC setDrvPct (MarlinFirmware#20205)

* [cron] Bump distribution date (2020-11-20)

* Longer LK Pro / Alfawise PRO board (MarlinFirmware#20185)

* Missing header to use suicide() on LVGL UI (MarlinFirmware#20214)

* SINGLE_TOUCH_NAVIGATION Follow Up (MarlinFirmware#20213)

* Printrboard labels

* [cron] Bump distribution date (2020-11-21)

* Fix backward Filament (Presence) Sensor pulls (MarlinFirmware#20228)

Co-authored-by: Kurt Haenen <Kurt.Haenen@quintux.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix bad SET_FAST_PWM_FREQ calls (MarlinFirmware#20227)

* Superscript substitution (MarlinFirmware#20219)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Power-Loss cleanup

* BTN_ENC_EN for many boards (MarlinFirmware#19890)

Enables CHECK_ENCODER_ACTIVE_SIGNAL for many more boards.

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Skip unnecessary (costly) SW Stepper Enable (MarlinFirmware#20218)

Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix Load Filament wait (MarlinFirmware#20243)

* Proper pullup/pulldown configurability (MarlinFirmware#20242)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* [cron] Bump distribution date (2020-11-22)

* Clear menu history for browse media on insert (MarlinFirmware#20236)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Put "$3" on all tests

* Move core conditionals earlier

* Hide docker droppings

* [cron] Bump distribution date (2020-11-23)

* Fix UBL manual mesh adjust behavior (MarlinFirmware#20248)

* Allow Status Message without LCD (MarlinFirmware#20246)

* Fix dummy thermistors for Bed, Chamber, Probe (MarlinFirmware#20247)

* Fix Z4 in ENABLE/DISABLE_AXIS_Z (MarlinFirmware#20256)

This was accidentally broken in PR MarlinFirmware#20218

* [cron] Bump distribution date (2020-11-24)

* LCD position in current units (MarlinFirmware#20145)

* Set "lcd_move_e" index to fix the label (MarlinFirmware#20263)

* Allow cold Filament Load/Unload with M302 P1 (MarlinFirmware#20262)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* No Z_MULTI_ENDSTOPS when HOMING_Z_WITH_PROBE (MarlinFirmware#20254)

* Consistent Probe XY offset type

* Cosmetic G29 ABL tweak

* [cron] Bump distribution date (2020-11-25)

* Update TOUCH_UI_LULZBOT_BIO wrappers

* add missing header to use HAS_SD_HOST_DRIVE (MarlinFirmware#20270)

* Fix COLOR_UI without TOUCH_SCREEN_CALIBRATION (MarlinFirmware#20269)

* [cron] Bump distribution date (2020-11-26)

* Probe Offset Wizard improvements (MarlinFirmware#20239)

* Reduce warnings, extern "C" cleanup (MarlinFirmware#20279)

* Retire HAL for STM32F4 / F7 (MarlinFirmware#20153)

* Tweak some pin errors

* MKS Robin E3 / E3D v1.1 (MarlinFirmware#20216)

* Finish HAL/STM32 cpp wrappers

* No auto debug for EEPROM_CHITCHAT

* Optimize emergency parser check

* Level Corners with Probe option (MarlinFirmware#20241)

* [WIP] Fix Probe::offset_xy (MarlinFirmware#20290)

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-11-27)

* M808 Repeat Markers (MarlinFirmware#20084)

* FIX TMC menu message (MarlinFirmware#20294)

* Fix BTT GTR 1.0 endstop/DIAG pins (MarlinFirmware#20296)

* Fix G2/G3 arcs > 180° (MarlinFirmware#20292)

* Group related homing options (MarlinFirmware#20283)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Fix M73 LCD code typo (MarlinFirmware#20300)

* [cron] Bump distribution date (2020-11-28)

* [cron] Bump distribution date (2020-11-29)

* Arc Direction followup for circles (MarlinFirmware#20314)

* SKR E3 Turbo Controller Fan (MarlinFirmware#20320)

* Fix STM32F1 'freeMemory()' warnings (MarlinFirmware#20319)

* Leveling Fade Height default setting (MarlinFirmware#20316)

* [cron] Bump distribution date (2020-11-30)

* Adjust axis homed / trusted methods (MarlinFirmware#20323)

* General cleanup

* Increase E3V2 DWIN steps/mm range to 999.9 (MarlinFirmware#20324)

* [cron] Bump distribution date (2020-12-01)

* Prevent Watchdog reset writing Creality 4.x EEPROM (MarlinFirmware#20328)

* Fix E3V2 Control Menu when returning from Info (MarlinFirmware#20338)

* Tweak to EEPROM safe delay

* [cron] Bump distribution date (2020-12-02)

* Level Bed Corners is a sub-menu

* Update to STM32 v10, optimize build (MarlinFirmware#20325)

* Help hosts when password-locked (MarlinFirmware#20348)

* Fix E3V2 DWIN Jerk Menu (MarlinFirmware#20352)

* Fix E3V2 DWIN build without CLASSIC_JERK
* Fix jerk edits applying to wrong index

* Permit SD EEPROM emulation on E3V2 (MarlinFirmware#20353)

* [cron] Bump distribution date (2020-12-03)

* Fix circle arc condition (MarlinFirmware#20322)

* Fix up start, monitor baud (MarlinFirmware#20326)

* Consolidate common pin includes

* Require minimum PlatformIO version (MarlinFirmware#20361)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-12-04)

* Fix MESH_BED_LEVELING w/o SEGMENT_LEVELED_MOVES (MarlinFirmware#20363)

* Loosen E on pause for fila-manipulation (MarlinFirmware#20346)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-05)

* Don’t use near keyword as variable name (MarlinFirmware#20374)

* Improved Longer3D LKx Pro board (MarlinFirmware#20372)

Co-authored-by: mrv96 <marione96@live.it>

* Fix TMC_HOME_PHASE divide by zero (MarlinFirmware#20368)

* Suspend Servos for STM32+NeoPixel (MarlinFirmware#19963)

* Add Creality 4.5.2 board (MarlinFirmware#20378)

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-12-06)

* Fix FYSETC S6 I2C EEPROM size (MarlinFirmware#20340)

Both V1.2 and V2.0 boards have a 24LC16, which is a 2kB EEPROM.

Co-authored-by: PingWin <kirill@shashlov.ru>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Creality 4.5.2 format and fix

* Use 'nearby' for 'near'

* ExtUI homing / leveling additions

* Move G29 3-point startup earlier

* Fix STM32F1 SERIAL_GET_TX_BUFFER_FREE

* G28 tweaks

* G28 followup

* Avoid invalid memory optimizations (MarlinFirmware#20389)

When building for AVR, merge-all-constants can incorrectly combine constants stored in flash with constants stored in RAM. These have different access requirements, leading to undefined behavior during execution.
Co-authored-by: ellensp <ellensp@hotmail.com>

* [cron] Bump distribution date (2020-12-07)

* Fix fileExists, use openFailed

* Watch idle() depth over 5

* More LPC P-string macros

* Fix auto#.g file handling, add NO_SD_AUTOSTART (MarlinFirmware#20071)

* Shorten Filament Load/Unload Strings to Fit on Graphical Displays (MarlinFirmware#20369)

Co-authored-by: ellensp <ellensp@ellensp-HP-ProBook-6470b.fritz.box>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>

* Allow BTT EXP-MOT be used with Displays that needs only EXP 1 (MarlinFirmware#20396)

Co-authored-by: ellensp <ellensp@ellensp-HP-ProBook-6470b.fritz.box>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>

* [cron] Bump distribution date (2020-12-08)

* SPI TFT for STM32F4 boards (MarlinFirmware#20384)

* fix pinsDebug for F1 boards

* add MKS Robin PRO V2 board - development board

* tft spi working with F4 boards

* pins formating

* sanity check for TFT on supported cores in STM32

* Fix tabs/spaces in pins file

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-12-09)

* Style, spacing, typo cleanup for recent changes

* Clarify Delta & SCARA config location (MarlinFirmware#20403)

* Allow positive Z nozzle to probe offset (MarlinFirmware#20344)

* Allow a positive value for z offset from nozzle to probe without sanity checks
* Simplify menu_probe_offset.cpp (HOMING_Z_WITH_PROBE)
* Add some more explanation to Configuration Files
* Raise after probe_at_point as if homed

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Fix Spindle/Laser Control menu (MarlinFirmware#20347)

* Fixes and additions to FTDI EVE Touch UI (MarlinFirmware#20393)

- Fixed name conflict with "SUBSCRIPT_TWO"
- Fixed rendering bugs in "Leveling Menu"
- Only show "Bed Mesh Screen" when UBL is enabled
- Removed CocoaPress code from generic "Main Menu"
- Removed CocoaPress code from LulzBot Bio "Status" screen
- Moved generic "Move Axis" functionality into a base class
- Added CocoaPress custom screens:
   - Status Screen
   - Unload Cartridge
   - Load Chocolate
   - Main Menu
   - Advanced Settings
   - XYZ Move (based on "Move Axis" base class)
   - Extrusion Move (based on "Move Axis" base class)
- CocoaPress tweaks to "Temperature" screen
- Fix FTDI EVE Touch UI compilation errors when not using leveling.

* Move ExtUI ABL mesh edit, limit to bilinear (MarlinFirmware#20381)

* Move ExtUI call

Co-authored-by: Scott Lahteine <github@thinkyhead.com>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>
Co-authored-by: Sebastiaan Dammann <sebastiaandammann@outlook.com>

* MKS Robin Pins fixes for STM32 and STM32F1 (MarlinFirmware#20404)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-10)

* Clarify "not Interrupt-capable" error message (MarlinFirmware#20419)

* Fix UBL Debug Messages (MarlinFirmware#20423)

Co-authored-by: ellensp <ellensp@hotmsil.com>

* [cron] Bump distribution date (2020-12-11)

* Z_SENSORLESS sanity checks (MarlinFirmware#20421)

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Probe offset wizard fixes (MarlinFirmware#20414)

* STOW probe, reverting incorrect earlier change from MarlinFirmware#20344
* Adjust soft endstop disables, to ensure travel below bed functions properly

Co-authored-by: FanDjango <FanDjango@users.noreply.github.com>

* SENSORLESS_PROBING sanity check followup (MarlinFirmware#20438)

* [cron] Bump distribution date (2020-12-12)

* Better animated boot screen

* Fix SDCARD_SORT_ALPHA on Ender 3 V2 (MarlinFirmware#20443)

* Add HAS_PIN_27_BOARD for CREALITY_V4 (MarlinFirmware#20446)

Co-authored-by: ellensp <ellensp@hotmsil.com>

* Improve ASSISTED_TRAMMING_WIZARD probe stowing (MarlinFirmware#20437)

* When BLTOUCH_HS_MODE enabled, stow pin before user interaction
* For all probes, ensure probe stows at end of wizard

* [cron] Bump distribution date (2020-12-13)

* Probe Offset Wizard followupBack to PROBE_PT_RAISE/separate STOW, make "PROBING" msg appear (MarlinFirmware#20439)

* Go back to always use PROBE_PT_RAISE with a discrete stow. This ensures a raise above the bed, while stowing prior to exiting the wizard.
* Fix issue preventing text while moving to X/Y position
Co-authored-by: FanDjango <FanDjango@users.noreply.github.com>

* Adjust planner debugging

* SHORT_MANUAL_Z_MOVE => FINE_MANUAL_MOVE

* [cron] Bump distribution date (2020-12-14)

* LPC176x framework update (MarlinFirmware#20469)

* [cron] Bump distribution date (2020-12-15)

* Fix formatting

* Preheat before leveling

* Always enable leveling after G28

* Trust that script -x flags will always be set (MarlinFirmware#20453)

* Fix M1001 auto-check logic (MarlinFirmware#20456)

* Auto-check followup

* Please install the EditorConfig plugin

* Fix RESTORE_LEVELING_AFTER_G28 (MarlinFirmware#20471)

* Creality v4.5.3 (CR-6 SE, CR-6 MAX) (MarlinFirmware#20468)

* Update some pins errors

* Update some LCD includes

* Trust STM32 gcc versions

* [cron] Bump distribution date (2020-12-16)

* Update Italian language (MarlinFirmware#20480)

* Update Hungarian language

Co-Authored-By: Zs.Antal <45710979+AntoszHUN@users.noreply.github.com>

* Update French language (MarlinFirmware#20472)

* [cron] Bump distribution date (2020-12-17)

* Use homing_feedrate function

* Homing feedrates as XYZ array (MarlinFirmware#20426)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Fix ZoneStar LCD 2004 buttons (MarlinFirmware#20489)

* Make M220 B / R a standard feature (MarlinFirmware#20355)

* Balance CI tests (MarlinFirmware#20485)

* Fix and optimize MightyBoard (MarlinFirmware#20493)

* [cron] Bump distribution date (2020-12-18)

* MKS Robin Nano V3 and STM32F4x0Vx Variant (MarlinFirmware#20430)

* DOGM: Slow down touchscreen calibration (MarlinFirmware#20454)

* [cron] Bump distribution date (2020-12-19)

* Rename QUIET_PROBING

* Tweaks for pins_BTT_SKR_common.h

* [cron] Bump distribution date (2020-12-20)

* Let boards set Default TMC Slave Addresses (MarlinFirmware#20498)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Minimum temp options for Probing and G12 Nozzle Clean (MarlinFirmware#20383)

Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Probe Tare, Probe Activation Switch (MarlinFirmware#20379)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Fix Creality EEPROM watchdog freq. (MarlinFirmware#20510)

* Migrate Hispeedv1 (QQS-Pro) to HAL/STM32 (MarlinFirmware#20354)

* Languages cleanup

* Update Russian and Ukrainian languages (MarlinFirmware#20508)

* Fix PIO typo

* [cron] Bump distribution date (2020-12-21)

* Get E3V2 DWIN `MACHINE_SIZE` from config (MarlinFirmware#20526)

* Apply HOME_AFTER_DEACTIVATE for 'G28 O' (MarlinFirmware#20525)

* Clean up some pins

* Add BTT SKR CR6 board (MarlinFirmware#20522)

* Fix G34 compile with bed leveling disabled (MarlinFirmware#20537)

* Fix some Russian (MarlinFirmware#20529)

* Robin pins followup

* Tweak FTDI spacing

* Add Tune -> Advanced Settings to FTDI EVE (MarlinFirmware#20532)

* [cron] Bump distribution date (2020-12-22)

* 12-bit ADC resolution for STM32 (MarlinFirmware#20519)

* FTDI EVE custom user menus (MarlinFirmware#20518)

* Improve STM32 timer conflict messages (MarlinFirmware#20544)

* Fix UBL mesh inset Z position (MarlinFirmware#20538)

* Overrides to prevent STM32 timer conflicts (MarlinFirmware#20545)

* Improve Touch Calibration screen (MarlinFirmware#20524)

* Creality v4.3.1 (Ender 6) board (MarlinFirmware#20512)

* Anet ET4 / ET4P and Anet TFT28 / TFT35 (MarlinFirmware#20280)

* STM32F1xx support for TFTGLCD (MarlinFirmware#20515)

* Unify FYSETC F6 1.3 / 1.4 (MarlinFirmware#20507)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix G28 leveling state, UBL compile (MarlinFirmware#20499)

* Support RGBW on PCA9632 (MarlinFirmware#20455)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-23)

* Refactor 'Level Corners with Probe' (MarlinFirmware#20460)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Improve plan_arc circle detection (MarlinFirmware#20440)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* FTDI EVE: Cyrillic font, some minor fixes (MarlinFirmware#20517)

* Enhanced Italian language (MarlinFirmware#20551)

* Probe Activation Switch followup (MarlinFirmware#20550)

* Support ANET_FULL_GRAPHICS_LCD_ALT_WIRING on BTT SKR 1.4 (MarlinFirmware#20427)

* Apply ENABLED in ExiUI / FTDI

* Remaining Time for FTDI EVE, bp for ExtUI (MarlinFirmware#20549)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Add OPTIMIZED_MESH_STORAGE option (for UBL) (MarlinFirmware#20371)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-24)

* Move BTT_SKR_CR6

* LVGL and Classic UI for STM32 (MarlinFirmware#20552)

* Add "End Repeat Loops" menu item

* Fix DOGM status message scrolling (MarlinFirmware#20557)

* Fix ST7920 timing for Rumba32, Fysetc S6 (MarlinFirmware#20556)

* Fix, clean up FTDI EVE Touch UI (MarlinFirmware#20466)

Co-Authored-By: Marcio T. <mlt4356-github@yahoo.com>

* Apply NO_MOTION_BEFORE_HOMING to joystick motion (MarlinFirmware#20462)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Cutter Power in percent format (MarlinFirmware#20410)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: Luu Lac <45380455+shitcreek@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-25)

* [cron] Bump distribution date (2020-12-26)

* [cron] Bump distribution date (2020-12-27)

* Fix SPINDLE_LASER_FREQUENCY (MarlinFirmware#20509)

* Fix some comments

* Remove CREALITY_TOUCH

* Add probe_switch_activated

* Init tare pin once

* [cron] Bump distribution date (2020-12-28)

* Validate defined probe points (MarlinFirmware#20572)

* General cleanup

* Allow define HOMING_FEEDRATE_(XY|Z)

* Remove URL scheme

* Small / Large Boot Screen option for TFT_COLOR_UI (MarlinFirmware#20578)

* Better defaults, compatibility for SDIO + STM32 (MarlinFirmware#20570)

* Fix Menu Mixer for Color UI (MarlinFirmware#20566)

* Use ADC_RESOLUTION 12 for all STM32 (MarlinFirmware#20562)

* Fix LVGL_UI G-code preview (MarlinFirmware#20564)

* Fix Change Filament menu actions (MarlinFirmware#20565)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Menu item index followup

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Giuliano Zaro <3684609+GMagician@users.noreply.github.com>
Co-authored-by: bosd <evbokhoven@gmail.com>
Co-authored-by: JoAnn Manges <joannmanges@gmail.com>
Co-authored-by: Victor Oliveira <rhapsodyv@gmail.com>
Co-authored-by: ellensp <ellensp@hotmail.com>
Co-authored-by: Maciej Rutkowski <onfoot@users.noreply.github.com>
Co-authored-by: Till <quastus@gmail.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>
Co-authored-by: Vitaliy <burkut_vit@mail.ru>
Co-authored-by: Orel <37673727+0r31@users.noreply.github.com>
Co-authored-by: Ajtak <ajtak.jakub@gmail.com>
Co-authored-by: Kurt Haenen <Misterke@users.noreply.github.com>
Co-authored-by: Kurt Haenen <Kurt.Haenen@quintux.com>
Co-authored-by: Simone Primarosa <simonepri@outlook.com>
Co-authored-by: Gurmeet Athwal <gurmeet.athwal@gmail.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: qwewer0 <57561110+qwewer0@users.noreply.github.com>
Co-authored-by: rdhoggattjr <64983896+rdhoggattjr@users.noreply.github.com>
Co-authored-by: pseudex <pseudaex@gmail.com>
Co-authored-by: swissnorp <67485708+swissnorp@users.noreply.github.com>
Co-authored-by: mks-viva <1224833100@qq.com>
Co-authored-by: wmariz <11435639+wmariz@users.noreply.github.com>
Co-authored-by: Štěpán Dalecký <36531759+daleckystepan@users.noreply.github.com>
Co-authored-by: BsCmOD <64871957+BsCmOD@users.noreply.github.com>
Co-authored-by: yysh12 <yysh12@users.noreply.github.com>
Co-authored-by: Sergey1560 <53866542+Sergey1560@users.noreply.github.com>
Co-authored-by: Thomas Niccolo Reyes <niccoreyes@gmail.com>
Co-authored-by: Alexander D. Kanevskiy <kad@kad.name>
Co-authored-by: Mathias Rasmussen <mathiasvr@gmail.com>
Co-authored-by: Luu Lac <45380455+shitcreek@users.noreply.github.com>
Co-authored-by: Belin Fieldson <thebelin@gmail.com>
Co-authored-by: Tanguy Pruvot <tpruvot@users.noreply.github.com>
Co-authored-by: mrv96 <marione96@live.it>
Co-authored-by: InsanityAutomation <38436470+InsanityAutomation@users.noreply.github.com>
Co-authored-by: LinFor <linfor@gmail.com>
Co-authored-by: PingWin <kirill@shashlov.ru>
Co-authored-by: ellensp <ellensp@ellensp-HP-ProBook-6470b.fritz.box>
Co-authored-by: Keith Bennett <13375512+thisiskeithb@users.noreply.github.com>
Co-authored-by: Mike La Spina <mike.laspina@shaw.ca>
Co-authored-by: Marcio T <mlt4356-github@yahoo.com>
Co-authored-by: Sebastiaan Dammann <sebastiaandammann@outlook.com>
Co-authored-by: ellensp <ellensp@hotmsil.com>
Co-authored-by: elasticdotventures <35611074+elasticdotventures@users.noreply.github.com>
Co-authored-by: FanDjango <51046875+FanDjango@users.noreply.github.com>
Co-authored-by: FanDjango <FanDjango@users.noreply.github.com>
Co-authored-by: leodoener <leodoener@gmail.com>
Co-authored-by: Chris Pepper <p3p@p3psoft.co.uk>
Co-authored-by: kisslorand <50251547+kisslorand@users.noreply.github.com>
Co-authored-by: Zs.Antal <45710979+AntoszHUN@users.noreply.github.com>
Co-authored-by: rafaljot <rafal@jastrzebscy.org>
Co-authored-by: nb-rapidia <43864438+nb-rapidia@users.noreply.github.com>
Co-authored-by: grauerfuchs <42082416+grauerfuchs@users.noreply.github.com>
Co-authored-by: Foxies <Foxies-CSTL@users.noreply.github.com>
Co-authored-by: Serhiy-K <52166448+Serhiy-K@users.noreply.github.com>
Co-authored-by: Dick Streefland <dick@streefland.net>
Co-authored-by: cr20-123 <66994235+cr20-123@users.noreply.github.com>
Co-authored-by: X-Ryl669 <boite.pour.spam@gmail.com>
Co-authored-by: Sean McGroty <sean@darkon.net>
Co-authored-by: Jan Krajdl <spm@spamik.cz>
Co-authored-by: Darren Peter <killallthehumans@gmail.com>
Co-authored-by: ubik2 <ubik2@users.noreply.github.com>
Co-authored-by: Vi B-P <violetbp@eecs.umich.edu>
Co-authored-by: Ashammaru <xgxede@gmail.com>
TheMichalcinOfficial added a commit to TheMichalcinOfficial/Marlin that referenced this pull request Dec 30, 2020
* MKS WiFi preliminary changes

* More MKS WiFi

* MKS WiFi strings

* Fix Z label

* Windows LPC Upload for non-admins (MarlinFirmware#20208)

Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix DAC setDrvPct (MarlinFirmware#20205)

* [cron] Bump distribution date (2020-11-20)

* Longer LK Pro / Alfawise PRO board (MarlinFirmware#20185)

* Missing header to use suicide() on LVGL UI (MarlinFirmware#20214)

* SINGLE_TOUCH_NAVIGATION Follow Up (MarlinFirmware#20213)

* Printrboard labels

* [cron] Bump distribution date (2020-11-21)

* Fix backward Filament (Presence) Sensor pulls (MarlinFirmware#20228)

Co-authored-by: Kurt Haenen <Kurt.Haenen@quintux.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix bad SET_FAST_PWM_FREQ calls (MarlinFirmware#20227)

* Superscript substitution (MarlinFirmware#20219)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Power-Loss cleanup

* BTN_ENC_EN for many boards (MarlinFirmware#19890)

Enables CHECK_ENCODER_ACTIVE_SIGNAL for many more boards.

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Skip unnecessary (costly) SW Stepper Enable (MarlinFirmware#20218)

Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix Load Filament wait (MarlinFirmware#20243)

* Proper pullup/pulldown configurability (MarlinFirmware#20242)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* [cron] Bump distribution date (2020-11-22)

* Clear menu history for browse media on insert (MarlinFirmware#20236)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Put "$3" on all tests

* Move core conditionals earlier

* Hide docker droppings

* [cron] Bump distribution date (2020-11-23)

* Fix UBL manual mesh adjust behavior (MarlinFirmware#20248)

* Allow Status Message without LCD (MarlinFirmware#20246)

* Fix dummy thermistors for Bed, Chamber, Probe (MarlinFirmware#20247)

* Fix Z4 in ENABLE/DISABLE_AXIS_Z (MarlinFirmware#20256)

This was accidentally broken in PR MarlinFirmware#20218

* [cron] Bump distribution date (2020-11-24)

* LCD position in current units (MarlinFirmware#20145)

* Set "lcd_move_e" index to fix the label (MarlinFirmware#20263)

* Allow cold Filament Load/Unload with M302 P1 (MarlinFirmware#20262)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* No Z_MULTI_ENDSTOPS when HOMING_Z_WITH_PROBE (MarlinFirmware#20254)

* Consistent Probe XY offset type

* Cosmetic G29 ABL tweak

* [cron] Bump distribution date (2020-11-25)

* Update TOUCH_UI_LULZBOT_BIO wrappers

* add missing header to use HAS_SD_HOST_DRIVE (MarlinFirmware#20270)

* Fix COLOR_UI without TOUCH_SCREEN_CALIBRATION (MarlinFirmware#20269)

* [cron] Bump distribution date (2020-11-26)

* Probe Offset Wizard improvements (MarlinFirmware#20239)

* Reduce warnings, extern "C" cleanup (MarlinFirmware#20279)

* Retire HAL for STM32F4 / F7 (MarlinFirmware#20153)

* Tweak some pin errors

* MKS Robin E3 / E3D v1.1 (MarlinFirmware#20216)

* Finish HAL/STM32 cpp wrappers

* No auto debug for EEPROM_CHITCHAT

* Optimize emergency parser check

* Level Corners with Probe option (MarlinFirmware#20241)

* [WIP] Fix Probe::offset_xy (MarlinFirmware#20290)

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-11-27)

* M808 Repeat Markers (MarlinFirmware#20084)

* FIX TMC menu message (MarlinFirmware#20294)

* Fix BTT GTR 1.0 endstop/DIAG pins (MarlinFirmware#20296)

* Fix G2/G3 arcs > 180° (MarlinFirmware#20292)

* Group related homing options (MarlinFirmware#20283)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Fix M73 LCD code typo (MarlinFirmware#20300)

* [cron] Bump distribution date (2020-11-28)

* [cron] Bump distribution date (2020-11-29)

* Arc Direction followup for circles (MarlinFirmware#20314)

* SKR E3 Turbo Controller Fan (MarlinFirmware#20320)

* Fix STM32F1 'freeMemory()' warnings (MarlinFirmware#20319)

* Leveling Fade Height default setting (MarlinFirmware#20316)

* [cron] Bump distribution date (2020-11-30)

* Adjust axis homed / trusted methods (MarlinFirmware#20323)

* General cleanup

* Increase E3V2 DWIN steps/mm range to 999.9 (MarlinFirmware#20324)

* [cron] Bump distribution date (2020-12-01)

* Prevent Watchdog reset writing Creality 4.x EEPROM (MarlinFirmware#20328)

* Fix E3V2 Control Menu when returning from Info (MarlinFirmware#20338)

* Tweak to EEPROM safe delay

* [cron] Bump distribution date (2020-12-02)

* Level Bed Corners is a sub-menu

* Update to STM32 v10, optimize build (MarlinFirmware#20325)

* Help hosts when password-locked (MarlinFirmware#20348)

* Fix E3V2 DWIN Jerk Menu (MarlinFirmware#20352)

* Fix E3V2 DWIN build without CLASSIC_JERK
* Fix jerk edits applying to wrong index

* Permit SD EEPROM emulation on E3V2 (MarlinFirmware#20353)

* [cron] Bump distribution date (2020-12-03)

* Fix circle arc condition (MarlinFirmware#20322)

* Fix up start, monitor baud (MarlinFirmware#20326)

* Consolidate common pin includes

* Require minimum PlatformIO version (MarlinFirmware#20361)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-12-04)

* Fix MESH_BED_LEVELING w/o SEGMENT_LEVELED_MOVES (MarlinFirmware#20363)

* Loosen E on pause for fila-manipulation (MarlinFirmware#20346)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-05)

* Don’t use near keyword as variable name (MarlinFirmware#20374)

* Improved Longer3D LKx Pro board (MarlinFirmware#20372)

Co-authored-by: mrv96 <marione96@live.it>

* Fix TMC_HOME_PHASE divide by zero (MarlinFirmware#20368)

* Suspend Servos for STM32+NeoPixel (MarlinFirmware#19963)

* Add Creality 4.5.2 board (MarlinFirmware#20378)

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-12-06)

* Fix FYSETC S6 I2C EEPROM size (MarlinFirmware#20340)

Both V1.2 and V2.0 boards have a 24LC16, which is a 2kB EEPROM.

Co-authored-by: PingWin <kirill@shashlov.ru>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Creality 4.5.2 format and fix

* Use 'nearby' for 'near'

* ExtUI homing / leveling additions

* Move G29 3-point startup earlier

* Fix STM32F1 SERIAL_GET_TX_BUFFER_FREE

* G28 tweaks

* G28 followup

* Avoid invalid memory optimizations (MarlinFirmware#20389)

When building for AVR, merge-all-constants can incorrectly combine constants stored in flash with constants stored in RAM. These have different access requirements, leading to undefined behavior during execution.
Co-authored-by: ellensp <ellensp@hotmail.com>

* [cron] Bump distribution date (2020-12-07)

* Fix fileExists, use openFailed

* Watch idle() depth over 5

* More LPC P-string macros

* Fix auto#.g file handling, add NO_SD_AUTOSTART (MarlinFirmware#20071)

* Shorten Filament Load/Unload Strings to Fit on Graphical Displays (MarlinFirmware#20369)

Co-authored-by: ellensp <ellensp@ellensp-HP-ProBook-6470b.fritz.box>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>

* Allow BTT EXP-MOT be used with Displays that needs only EXP 1 (MarlinFirmware#20396)

Co-authored-by: ellensp <ellensp@ellensp-HP-ProBook-6470b.fritz.box>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>

* [cron] Bump distribution date (2020-12-08)

* SPI TFT for STM32F4 boards (MarlinFirmware#20384)

* fix pinsDebug for F1 boards

* add MKS Robin PRO V2 board - development board

* tft spi working with F4 boards

* pins formating

* sanity check for TFT on supported cores in STM32

* Fix tabs/spaces in pins file

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* [cron] Bump distribution date (2020-12-09)

* Style, spacing, typo cleanup for recent changes

* Clarify Delta & SCARA config location (MarlinFirmware#20403)

* Allow positive Z nozzle to probe offset (MarlinFirmware#20344)

* Allow a positive value for z offset from nozzle to probe without sanity checks
* Simplify menu_probe_offset.cpp (HOMING_Z_WITH_PROBE)
* Add some more explanation to Configuration Files
* Raise after probe_at_point as if homed

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Fix Spindle/Laser Control menu (MarlinFirmware#20347)

* Fixes and additions to FTDI EVE Touch UI (MarlinFirmware#20393)

- Fixed name conflict with "SUBSCRIPT_TWO"
- Fixed rendering bugs in "Leveling Menu"
- Only show "Bed Mesh Screen" when UBL is enabled
- Removed CocoaPress code from generic "Main Menu"
- Removed CocoaPress code from LulzBot Bio "Status" screen
- Moved generic "Move Axis" functionality into a base class
- Added CocoaPress custom screens:
   - Status Screen
   - Unload Cartridge
   - Load Chocolate
   - Main Menu
   - Advanced Settings
   - XYZ Move (based on "Move Axis" base class)
   - Extrusion Move (based on "Move Axis" base class)
- CocoaPress tweaks to "Temperature" screen
- Fix FTDI EVE Touch UI compilation errors when not using leveling.

* Move ExtUI ABL mesh edit, limit to bilinear (MarlinFirmware#20381)

* Move ExtUI call

Co-authored-by: Scott Lahteine <github@thinkyhead.com>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>
Co-authored-by: Sebastiaan Dammann <sebastiaandammann@outlook.com>

* MKS Robin Pins fixes for STM32 and STM32F1 (MarlinFirmware#20404)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-10)

* Clarify "not Interrupt-capable" error message (MarlinFirmware#20419)

* Fix UBL Debug Messages (MarlinFirmware#20423)

Co-authored-by: ellensp <ellensp@hotmsil.com>

* [cron] Bump distribution date (2020-12-11)

* Z_SENSORLESS sanity checks (MarlinFirmware#20421)

Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Probe offset wizard fixes (MarlinFirmware#20414)

* STOW probe, reverting incorrect earlier change from MarlinFirmware#20344
* Adjust soft endstop disables, to ensure travel below bed functions properly

Co-authored-by: FanDjango <FanDjango@users.noreply.github.com>

* SENSORLESS_PROBING sanity check followup (MarlinFirmware#20438)

* [cron] Bump distribution date (2020-12-12)

* Better animated boot screen

* Fix SDCARD_SORT_ALPHA on Ender 3 V2 (MarlinFirmware#20443)

* Add HAS_PIN_27_BOARD for CREALITY_V4 (MarlinFirmware#20446)

Co-authored-by: ellensp <ellensp@hotmsil.com>

* Improve ASSISTED_TRAMMING_WIZARD probe stowing (MarlinFirmware#20437)

* When BLTOUCH_HS_MODE enabled, stow pin before user interaction
* For all probes, ensure probe stows at end of wizard

* [cron] Bump distribution date (2020-12-13)

* Probe Offset Wizard followupBack to PROBE_PT_RAISE/separate STOW, make "PROBING" msg appear (MarlinFirmware#20439)

* Go back to always use PROBE_PT_RAISE with a discrete stow. This ensures a raise above the bed, while stowing prior to exiting the wizard.
* Fix issue preventing text while moving to X/Y position
Co-authored-by: FanDjango <FanDjango@users.noreply.github.com>

* Adjust planner debugging

* SHORT_MANUAL_Z_MOVE => FINE_MANUAL_MOVE

* [cron] Bump distribution date (2020-12-14)

* LPC176x framework update (MarlinFirmware#20469)

* [cron] Bump distribution date (2020-12-15)

* Fix formatting

* Preheat before leveling

* Always enable leveling after G28

* Trust that script -x flags will always be set (MarlinFirmware#20453)

* Fix M1001 auto-check logic (MarlinFirmware#20456)

* Auto-check followup

* Please install the EditorConfig plugin

* Fix RESTORE_LEVELING_AFTER_G28 (MarlinFirmware#20471)

* Creality v4.5.3 (CR-6 SE, CR-6 MAX) (MarlinFirmware#20468)

* Update some pins errors

* Update some LCD includes

* Trust STM32 gcc versions

* [cron] Bump distribution date (2020-12-16)

* Update Italian language (MarlinFirmware#20480)

* Update Hungarian language

Co-Authored-By: Zs.Antal <45710979+AntoszHUN@users.noreply.github.com>

* Update French language (MarlinFirmware#20472)

* [cron] Bump distribution date (2020-12-17)

* Use homing_feedrate function

* Homing feedrates as XYZ array (MarlinFirmware#20426)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Fix ZoneStar LCD 2004 buttons (MarlinFirmware#20489)

* Make M220 B / R a standard feature (MarlinFirmware#20355)

* Balance CI tests (MarlinFirmware#20485)

* Fix and optimize MightyBoard (MarlinFirmware#20493)

* [cron] Bump distribution date (2020-12-18)

* MKS Robin Nano V3 and STM32F4x0Vx Variant (MarlinFirmware#20430)

* DOGM: Slow down touchscreen calibration (MarlinFirmware#20454)

* [cron] Bump distribution date (2020-12-19)

* Rename QUIET_PROBING

* Tweaks for pins_BTT_SKR_common.h

* [cron] Bump distribution date (2020-12-20)

* Let boards set Default TMC Slave Addresses (MarlinFirmware#20498)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Minimum temp options for Probing and G12 Nozzle Clean (MarlinFirmware#20383)

Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Probe Tare, Probe Activation Switch (MarlinFirmware#20379)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>

* Fix Creality EEPROM watchdog freq. (MarlinFirmware#20510)

* Migrate Hispeedv1 (QQS-Pro) to HAL/STM32 (MarlinFirmware#20354)

* Languages cleanup

* Update Russian and Ukrainian languages (MarlinFirmware#20508)

* Fix PIO typo

* [cron] Bump distribution date (2020-12-21)

* Get E3V2 DWIN `MACHINE_SIZE` from config (MarlinFirmware#20526)

* Apply HOME_AFTER_DEACTIVATE for 'G28 O' (MarlinFirmware#20525)

* Clean up some pins

* Add BTT SKR CR6 board (MarlinFirmware#20522)

* Fix G34 compile with bed leveling disabled (MarlinFirmware#20537)

* Fix some Russian (MarlinFirmware#20529)

* Robin pins followup

* Tweak FTDI spacing

* Add Tune -> Advanced Settings to FTDI EVE (MarlinFirmware#20532)

* [cron] Bump distribution date (2020-12-22)

* 12-bit ADC resolution for STM32 (MarlinFirmware#20519)

* FTDI EVE custom user menus (MarlinFirmware#20518)

* Improve STM32 timer conflict messages (MarlinFirmware#20544)

* Fix UBL mesh inset Z position (MarlinFirmware#20538)

* Overrides to prevent STM32 timer conflicts (MarlinFirmware#20545)

* Improve Touch Calibration screen (MarlinFirmware#20524)

* Creality v4.3.1 (Ender 6) board (MarlinFirmware#20512)

* Anet ET4 / ET4P and Anet TFT28 / TFT35 (MarlinFirmware#20280)

* STM32F1xx support for TFTGLCD (MarlinFirmware#20515)

* Unify FYSETC F6 1.3 / 1.4 (MarlinFirmware#20507)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

* Fix G28 leveling state, UBL compile (MarlinFirmware#20499)

* Support RGBW on PCA9632 (MarlinFirmware#20455)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-23)

* Refactor 'Level Corners with Probe' (MarlinFirmware#20460)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Improve plan_arc circle detection (MarlinFirmware#20440)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* FTDI EVE: Cyrillic font, some minor fixes (MarlinFirmware#20517)

* Enhanced Italian language (MarlinFirmware#20551)

* Probe Activation Switch followup (MarlinFirmware#20550)

* Support ANET_FULL_GRAPHICS_LCD_ALT_WIRING on BTT SKR 1.4 (MarlinFirmware#20427)

* Apply ENABLED in ExiUI / FTDI

* Remaining Time for FTDI EVE, bp for ExtUI (MarlinFirmware#20549)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Add OPTIMIZED_MESH_STORAGE option (for UBL) (MarlinFirmware#20371)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-24)

* Move BTT_SKR_CR6

* LVGL and Classic UI for STM32 (MarlinFirmware#20552)

* Add "End Repeat Loops" menu item

* Fix DOGM status message scrolling (MarlinFirmware#20557)

* Fix ST7920 timing for Rumba32, Fysetc S6 (MarlinFirmware#20556)

* Fix, clean up FTDI EVE Touch UI (MarlinFirmware#20466)

Co-Authored-By: Marcio T. <mlt4356-github@yahoo.com>

* Apply NO_MOTION_BEFORE_HOMING to joystick motion (MarlinFirmware#20462)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Cutter Power in percent format (MarlinFirmware#20410)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: Luu Lac <45380455+shitcreek@users.noreply.github.com>

* [cron] Bump distribution date (2020-12-25)

* [cron] Bump distribution date (2020-12-26)

* [cron] Bump distribution date (2020-12-27)

* Fix SPINDLE_LASER_FREQUENCY (MarlinFirmware#20509)

* Fix some comments

* Remove CREALITY_TOUCH

* Add probe_switch_activated

* Init tare pin once

* [cron] Bump distribution date (2020-12-28)

* Validate defined probe points (MarlinFirmware#20572)

* General cleanup

* Allow define HOMING_FEEDRATE_(XY|Z)

* Remove URL scheme

* Small / Large Boot Screen option for TFT_COLOR_UI (MarlinFirmware#20578)

* Better defaults, compatibility for SDIO + STM32 (MarlinFirmware#20570)

* Fix Menu Mixer for Color UI (MarlinFirmware#20566)

* Use ADC_RESOLUTION 12 for all STM32 (MarlinFirmware#20562)

* Fix LVGL_UI G-code preview (MarlinFirmware#20564)

* Fix Change Filament menu actions (MarlinFirmware#20565)

Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>

* Menu item index followup

* [cron] Bump distribution date (2020-12-29)

* Apply SHOW_BOOTSCREEN to TFT_COLOR_UI (MarlinFirmware#20586)

* LVGL G-code preview. Legacy MKS WiFi Cura plugin compatibility (MarlinFirmware#20589)

* Clarify sanity-check for custom status bitmap (MarlinFirmware#20588)

* Pins, comment cleanup

* USB FD via native USB Host + MSC (MarlinFirmware#20571)

* Support 4.3" (480x272) Color UI display (MarlinFirmware#20334)

* [cron] Bump distribution date (2020-12-30)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>
Co-authored-by: Vitaliy <burkut_vit@mail.ru>
Co-authored-by: Victor Mateus Oliveira <rhapsodyv@gmail.com>
Co-authored-by: Orel <37673727+0r31@users.noreply.github.com>
Co-authored-by: thinkyhead <thinkyhead@users.noreply.github.com>
Co-authored-by: Ajtak <ajtak.jakub@gmail.com>
Co-authored-by: Kurt Haenen <Misterke@users.noreply.github.com>
Co-authored-by: Kurt Haenen <Kurt.Haenen@quintux.com>
Co-authored-by: Simone Primarosa <simonepri@outlook.com>
Co-authored-by: Gurmeet Athwal <gurmeet.athwal@gmail.com>
Co-authored-by: Jason Smith <jason.inet@gmail.com>
Co-authored-by: qwewer0 <57561110+qwewer0@users.noreply.github.com>
Co-authored-by: rdhoggattjr <64983896+rdhoggattjr@users.noreply.github.com>
Co-authored-by: ellensp <ellensp@hotmail.com>
Co-authored-by: pseudex <pseudaex@gmail.com>
Co-authored-by: swissnorp <67485708+swissnorp@users.noreply.github.com>
Co-authored-by: mks-viva <1224833100@qq.com>
Co-authored-by: wmariz <11435639+wmariz@users.noreply.github.com>
Co-authored-by: Štěpán Dalecký <36531759+daleckystepan@users.noreply.github.com>
Co-authored-by: BsCmOD <64871957+BsCmOD@users.noreply.github.com>
Co-authored-by: yysh12 <yysh12@users.noreply.github.com>
Co-authored-by: Sergey1560 <53866542+Sergey1560@users.noreply.github.com>
Co-authored-by: Thomas Niccolo Reyes <niccoreyes@gmail.com>
Co-authored-by: Alexander D. Kanevskiy <kad@kad.name>
Co-authored-by: Mathias Rasmussen <mathiasvr@gmail.com>
Co-authored-by: Luu Lac <45380455+shitcreek@users.noreply.github.com>
Co-authored-by: Belin Fieldson <thebelin@gmail.com>
Co-authored-by: Tanguy Pruvot <tpruvot@users.noreply.github.com>
Co-authored-by: mrv96 <marione96@live.it>
Co-authored-by: InsanityAutomation <38436470+InsanityAutomation@users.noreply.github.com>
Co-authored-by: LinFor <linfor@gmail.com>
Co-authored-by: PingWin <kirill@shashlov.ru>
Co-authored-by: ellensp <ellensp@ellensp-HP-ProBook-6470b.fritz.box>
Co-authored-by: Keith Bennett <13375512+thisiskeithb@users.noreply.github.com>
Co-authored-by: Mike La Spina <mike.laspina@shaw.ca>
Co-authored-by: Marcio T <mlt4356-github@yahoo.com>
Co-authored-by: Sebastiaan Dammann <sebastiaandammann@outlook.com>
Co-authored-by: ellensp <ellensp@hotmsil.com>
Co-authored-by: elasticdotventures <35611074+elasticdotventures@users.noreply.github.com>
Co-authored-by: FanDjango <51046875+FanDjango@users.noreply.github.com>
Co-authored-by: FanDjango <FanDjango@users.noreply.github.com>
Co-authored-by: leodoener <leodoener@gmail.com>
Co-authored-by: Chris Pepper <p3p@p3psoft.co.uk>
Co-authored-by: kisslorand <50251547+kisslorand@users.noreply.github.com>
Co-authored-by: JoAnn Manges <joannmanges@gmail.com>
Co-authored-by: Giuliano Zaro <3684609+GMagician@users.noreply.github.com>
Co-authored-by: Zs.Antal <45710979+AntoszHUN@users.noreply.github.com>
Co-authored-by: rafaljot <rafal@jastrzebscy.org>
Co-authored-by: nb-rapidia <43864438+nb-rapidia@users.noreply.github.com>
Co-authored-by: grauerfuchs <42082416+grauerfuchs@users.noreply.github.com>
Co-authored-by: Foxies <Foxies-CSTL@users.noreply.github.com>
Co-authored-by: Serhiy-K <52166448+Serhiy-K@users.noreply.github.com>
Co-authored-by: Dick Streefland <dick@streefland.net>
Co-authored-by: cr20-123 <66994235+cr20-123@users.noreply.github.com>
Co-authored-by: X-Ryl669 <boite.pour.spam@gmail.com>
Co-authored-by: Sean McGroty <sean@darkon.net>
Co-authored-by: Jan Krajdl <spm@spamik.cz>
Co-authored-by: Darren Peter <killallthehumans@gmail.com>
Co-authored-by: ubik2 <ubik2@users.noreply.github.com>
Co-authored-by: Vi B-P <violetbp@eecs.umich.edu>
Co-authored-by: Ashammaru <xgxede@gmail.com>
tharts pushed a commit to tharts/Marlin that referenced this pull request Jan 6, 2021
dpreed pushed a commit to dpreed/Marlin_2.0.x that referenced this pull request Feb 5, 2021
kpishere pushed a commit to kpishere/Marlin that referenced this pull request Feb 19, 2021
zillarob pushed a commit to zillarob/Marlin that referenced this pull request Feb 25, 2021
W4tel-BiDi pushed a commit to W4tel-BiDi/Marlin that referenced this pull request Apr 5, 2021
chrisjenda pushed a commit to chrisjenda/Marlin that referenced this pull request Apr 8, 2021
chrisjenda pushed a commit to chrisjenda/Marlin that referenced this pull request Apr 11, 2021
thinkyhead pushed a commit to thinkyhead/Marlin that referenced this pull request Apr 28, 2021
thinkyhead pushed a commit to thinkyhead/Marlin that referenced this pull request Apr 29, 2021
thinkyhead pushed a commit that referenced this pull request Apr 30, 2021
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Projects
None yet
Development

Successfully merging this pull request may close these issues.

5 participants