Different hardware than assembly guide/ videos #98
Comments
|
Is the difference that you are missing the ring? If that is the case I recommend using this linkage kit: http://maslowcommunitygarden.org/Maslow-triangulation-linkage-kit.html and then you can follow the normal instructions substituting the linkage for the ring. It will be a little bit more work, but you will get much better results than without the ring |
|
No I have the ring kit and z axis. It's hardware that I ran into after
mounting the motors
…On Wed, Jan 2, 2019, 8:00 PM BarbourSmith ***@***.*** wrote:
Is the difference that you are missing the ring?
If that is the case I recommend using this linkage kit:
http://maslowcommunitygarden.org/Maslow-triangulation-linkage-kit.html
and then you can follow the normal instructions substituting the linkage
for the ring. It will be a little bit more work, but you will get much
better results than without the ring
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
<#98 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AnoJ7woMvZsyoO66qortOST2WzkfaUhNks5u_VY7gaJpZM4ZnZek>
.
|
|
hmmmm I am not sure what hardware that would be. Can you post a picture of what part it is? |
|
Ahh ok I had to go to the instructions for the original design and the
parts were chain guides they changed the nails as well as added bushings
for the string pulleys.
…On Wed, Jan 2, 2019, 8:58 PM BarbourSmith ***@***.*** wrote:
hmmmm I am not sure what hardware that would be. Can you post a picture of
what part it is?
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
<#98 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AnoJ78j9OmM2b92_q31lIyLobehoP31Pks5u_WPegaJpZM4ZnZek>
.
|
|
Excellent!
Can I ask how you ended up with the out of date instructions? Maybe I can
fix something to make them less confusing in the future.
…On Thu, Jan 3, 2019, 10:50 AM PoliciaMalo ***@***.*** wrote:
Ahh ok I had to go to the instructions for the original design and the
parts were chain guides they changed the nails as well as added bushings
for the string pulleys.
On Wed, Jan 2, 2019, 8:58 PM BarbourSmith ***@***.*** wrote:
> hmmmm I am not sure what hardware that would be. Can you post a picture
of
> what part it is?
>
> —
> You are receiving this because you authored the thread.
> Reply to this email directly, view it on GitHub
> <#98 (comment)
>,
> or mute the thread
> <
https://github.com/notifications/unsubscribe-auth/AnoJ78j9OmM2b92_q31lIyLobehoP31Pks5u_WPegaJpZM4ZnZek
>
> .
>
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#98 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AI7QVzDIGMK9ZD-HsVVQhZe0MqVVBxWvks5u_W_dgaJpZM4ZnZek>
.
|
|
The instructions on the website under the new default frame do not mention
the parts used in the old default frame. Specifically the use of nails
instead of screws in the center bungee bearings, the use of nails now on
the center bearings instead of screws. The small 2 inch plastil bearing
used in chain tension for the old default frame. Etc. I'll elaborate more
in the dorms when build complete.
Also the bungees seem too long compard to the photos in the new default
frame build. I just ordered new bungee spool in case needed.
Thanks.
…On Fri, Jan 4, 2019, 7:14 PM BarbourSmith ***@***.*** wrote:
Excellent!
Can I ask how you ended up with the out of date instructions? Maybe I can
fix something to make them less confusing in the future.
On Thu, Jan 3, 2019, 10:50 AM PoliciaMalo ***@***.*** wrote:
> Ahh ok I had to go to the instructions for the original design and the
> parts were chain guides they changed the nails as well as added bushings
> for the string pulleys.
>
> On Wed, Jan 2, 2019, 8:58 PM BarbourSmith ***@***.***
wrote:
>
> > hmmmm I am not sure what hardware that would be. Can you post a picture
> of
> > what part it is?
> >
> > —
> > You are receiving this because you authored the thread.
> > Reply to this email directly, view it on GitHub
> > <
#98 (comment)
> >,
> > or mute the thread
> > <
>
https://github.com/notifications/unsubscribe-auth/AnoJ78j9OmM2b92_q31lIyLobehoP31Pks5u_WPegaJpZM4ZnZek
> >
> > .
> >
>
> —
> You are receiving this because you commented.
> Reply to this email directly, view it on GitHub
> <#98 (comment)
>,
> or mute the thread
> <
https://github.com/notifications/unsubscribe-auth/AI7QVzDIGMK9ZD-HsVVQhZe0MqVVBxWvks5u_W_dgaJpZM4ZnZek
>
> .
>
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
<#98 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AnoJ7394pb7MVEFzAs_XXVdYSzHQmTugks5u_-5ygaJpZM4ZnZek>
.
|
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
I finally got around to assembling my maslow cnc and there are hardware differences between the site instructions and what I received.
Is there an updated assembly guide for the new hardware?
Please... I'm dying to finish assembly.
The text was updated successfully, but these errors were encountered: