Skip to content

Latest commit

 

History

History
1516 lines (1201 loc) · 68 KB

proto.md

File metadata and controls

1516 lines (1201 loc) · 68 KB
Raw

The NBD protocol

Introduction

The Network Block Device is a Linux-originated lightweight block access protocol that allows one to export a block device to a client. While the name of the protocol specifically references the concept of block devices, there is nothing inherent in the protocol which requires that exports are, in fact, block devices; the protocol only concerns itself with a range of bytes, and several operations of particular lengths at particular offsets within that range of bytes.

For matters of clarity, in this document we will refer to an export from a server as a block device, even though the actual backing on the server need not be an actual block device; it may be a block device, a regular file, or a more complex configuration involving several files. That is an implementation detail of the server.

Conventions

In the below protocol descriptions, the label 'C:' is used for messages sent by the client, whereas 'S:' is used for messages sent by the server). monotype text is for literal character data or (when used in comments) constant names, 0xdeadbeef is used for literal hex numbers (which are always sent in network byte order), and (brackets) are used for comments. Anything else is a description of the data that is sent.

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119. The same words in lower case carry their natural meaning.

Where this document refers to a string, then unless otherwise stated, that string is a sequence of UTF-8 code points, which is not NUL terminated, MUST NOT contain NUL characters, SHOULD be no longer than 256 bytes and MUST be no longer than 4096 bytes. This applies to export names and error messages (amongst others). The length of a string is always available through information sent earlier in the same message, although it may require some computation based on the size of other data also present in the same message.

Protocol phases

The NBD protocol has two phases: the handshake and the transmission. During the handshake, a connection is established and an exported NBD device along other protocol parameters are negotiated between the client and the server. After a successful handshake, the client and the server proceed to the transmission phase in which the export is read from and written to.

On the client side under Linux, the handshake is implemented in userspace, while the transmission phase is implemented in kernel space. To get from the handshake to the transmission phase, the client performs

ioctl(nbd, NBD_SET_SOCK, sock)
ioctl(nbd, NBD_DO_IT)

with nbd in the above being a file descriptor for an open /dev/nbdX device node, and sock being the socket to the server. The second of the above two calls does not return until the client disconnects.

Note that there are other ioctl calls available, that are used by the client to communicate the options to the kernel which were negotiated with the server during the handshake. This document does not describe those.

Handshake

The handshake is the first phase of the protocol. Its main purpose is to provide means for both the client and the server to negotiate which export they are going to use and how.

There are three versions of the negotiation. They are referred to as "oldstyle", "newstyle", and "fixed newstyle" negotiation. Oldstyle was the only version of the negotiation until nbd 2.9.16; newstyle was introduced for nbd 2.9.17. A short while later, it was discovered that newstyle was insufficiently structured to allow protocol options to be added while retaining backwards compatibility. The minor changes introduced to fix this problem are, where necessary, referred to as "fixed newstyle" to differentiate from the original version of the newstyle negotiation.

Oldstyle negotiation

S: 64 bits, 0x4e42444d41474943 (ASCII 'NBDMAGIC') (also known as the INIT_PASSWD)
S: 64 bits, 0x00420281861253 (cliserv_magic, a magic number)
S: 64 bits, size of the export in bytes (unsigned)
S: 32 bits, flags
S: 124 bytes, zeroes (reserved).

As can be seen, this isn't exactly a negotiation; it's just a matter of the server sending a bunch of data to the client. If the client is unhappy with what he receives, he should disconnect and not look back.

The fact that the size of the export was specified before the flags were sent, made it impossible for the protocol to be changed in a backwards-compatible manner to allow for named exports without ugliness. As a result, the old style negotiation is now no longer developed; starting with version 3.10 of the reference implementation, it is also no longer supported.

Newstyle negotiation

A client who wants to use the new style negotiation SHOULD connect on the IANA-reserved port for NBD, 10809. The server MAY listen on other ports as well, but it SHOULD use the old style handshake on those. The server SHOULD refuse to allow oldstyle negotiations on the newstyle port. For debugging purposes, the server MAY change the port on which to listen for newstyle negotiation, but this SHOULD NOT happen for production purposes.

The initial few exchanges in newstyle negotiation look as follows:

S: 64 bits, 0x4e42444d41474943 (ASCII 'NBDMAGIC') (as in the old style handshake)
S: 64 bits, 0x49484156454F5054 (ASCII 'IHAVEOPT') (note different magic number)
S: 16 bits, handshake flags
C: 32 bits, client flags

This completes the initial phase of negotiation; the client and server now both know they understand the first version of the newstyle handshake, with no options. The client SHOULD ignore any handshake flags it does not recognize, while the server MUST close the TCP connection if it does not recognize the client's flags. What follows is a repeating group of options. In non-fixed newstyle only one option can be set (NBD_OPT_EXPORT_NAME), and it is not optional.

At this point, we move on to option haggling, during which point the client can send one or (in fixed newstyle) more options to the server. The generic format of setting an option is as follows:

C: 64 bits, 0x49484156454F5054 (ASCII 'IHAVEOPT') (note same newstyle handshake's magic number)
C: 32 bits, option
C: 32 bits, length of option data (unsigned)
C: any data needed for the chosen option, of length as specified above.

The presence of the option length in every option allows the server to skip any options presented by the client that it does not understand.

If the value of the option field is NBD_OPT_EXPORT_NAME and the server is willing to allow the export, the server replies with information about the used export:

S: 64 bits, size of the export in bytes (unsigned)
S: 16 bits, transmission flags
S: 124 bytes, zeroes (reserved) (unless NBD_FLAG_C_NO_ZEROES was negotiated by the client)

If the server is unwilling to allow the export, it MUST terminate the session.

The reason that the flags field is 16 bits large and not 32 as in the oldstyle negotiation is that there are now 16 bits of transmission flags, and 16 bits of handshake flags. Concatenated together, this results in 32 bits, which allows for using a common set of macros for both. If we ever run out of flags, the server will set the most significant flag bit, signalling that an extra flag field will follow, to which the client will have to reply with a flag field of its own before the extra flags are sent. This is not yet implemented.

Fixed newstyle negotiation

Unfortunately, due to a mistake, the server would immediately close the connection when it saw an option it did not understand, rather than signalling this fact to the client, which would've allowed it to retry; and replies from the server were not structured either, which meant that if the server were to send something the client did not understand, it would have to abort negotiation as well.

To fix these two issues, the following changes were implemented:

  • The server will set the handshake flag NBD_FLAG_FIXED_NEWSTYLE, to signal that it supports fixed newstyle negotiation.
  • The client SHOULD reply with NBD_FLAG_C_FIXED_NEWSTYLE set in its flags field too, though its side of the protocol does not change incompatibly.
  • The client MAY now send other options to the server as appropriate, in the generic format for sending an option as described above.
  • The server will reply to any option apart from NBD_OPT_EXPORT_NAME with reply packets in the following format:

S: 64 bits, 0x3e889045565a9 (magic number for replies)
S: 32 bits, the option as sent by the client to which this is a reply
S: 32 bits, reply type (e.g., NBD_REP_ACK for successful completion, or NBD_REP_ERR_UNSUP to mark use of an option not known by this server
S: 32 bits, length of the reply. This MAY be zero for some replies, in which case the next field is not sent
S: any data as required by the reply (e.g., an export name in the case of NBD_REP_SERVER)

The client MUST NOT send any option until it has received a final reply to any option it has sent (note that some options e.g. NBD_OPT_LIST have multiple replies, and the final reply is the last of those).

Some messages the client sends instruct the server to change some of its internal state. The client SHOULD NOT send such messages more than once; if it does, the server MAY fail the repeated message with NBD_REP_ERR_INVALID.

Termination of the session during option haggling

There are three possible mechanisms to end option haggling:

  • Transmission mode can be entered (by the client sending NBD_OPT_EXPORT_NAME or by the server responding to an NBD_OPT_GO with NBD_REP_ACK). This is documented elsewhere.

  • The client can send (and the server can reply to) an NBD_OPT_ABORT. This MUST be followed by the client shutting down TLS (if it is running), and the client dropping the connection. This is referred to as 'initiating a soft disconnect'; soft disconnects can only be initiated by the client.

  • The client or the server can disconnect the TCP session without activity at the NBD protocol level. If TLS is negotiated, the party initiating the transaction SHOULD shutdown TLS first if it is running. This is referred to as 'initiating a hard disconnect'.

This section concerns the second and third of these, together called 'terminating the session', and under which circumstances they are valid.

If either the client or the server detects a violation of a mandatory condition ('MUST' etc.) by the other party, it MAY initiate a hard disconnect.

A client MAY use a soft disconnect to terminate the session whenever it wishes.

A party that is mandated by this document to terminate the session MUST initiate a hard disconnect if it is not possible to use a soft disconnect. Such circumstances include: where that party is the server and it cannot return an error (e.g. after an NBD_OPT_EXPORT_NAME it cannot satisfy), and where that party is the client following a failed TLS negotiation.

A party MUST NOT initiate a hard disconnect save where set out in this section. Therefore, unless a client's situation falls within the provisions of the previous paragraph or the client detects a breach of a mandatory condition, it MUST NOT use a hard disconnect, and hence its only option to terminate the session is via a soft disconnect.

There is no requirement for the client or server to complete a negotiation if it does not wish to do so. Either end MAY simply terminate the session. In the client's case, if it wishes to do so it MUST use soft disconnect.

In the server's case it MUST (save where set out above) simply error inbound options until the client gets the hint that it is unwelcome, except that if a server believes a client's behaviour constitutes a denial of service, it MAY initiate a hard disconnect. If the server is in the process of being shut down it MAY error any inflight option and SHOULD error further options received (other than an NBD_OPT_ABORT) with NBD_REP_ERR_SHUTDOWN.

If the client receives NBD_REP_ERR_SHUTDOWN it MUST initiate a soft disconnect.

Transmission

There are two message types in the transmission phase: the request, and the reply. The transmission phase consists of a series of transactions, where the client submits requests and the server sends corresponding replies. The phase continues until either side terminates transmission; this can be performed cleanly only by the client.

Replies need not be sent in the same order as requests (i.e., requests may be handled by the server asynchronously). Clients SHOULD use a handle that is distinct from all other currently pending transactions, but MAY reuse handles that are no longer in flight; handles need not be consecutive. In each reply message the server MUST use the same value for handle as was sent by the client in the corresponding request. In this way, the client can correlate which request is receiving a response.

Ordering of messages and writes

The server MAY process commands out of order, and MAY reply out of order, except that:

  • All write commands (that includes NBD_CMD_WRITE, NBD_CMD_WRITE_ZEROES and NBD_CMD_TRIM) that the server completes (i.e. replies to) prior to processing a NBD_CMD_FLUSH MUST be written to non-volatile storage prior to replying to that NBD_CMD_FLUSH. This paragraph only applies if NBD_FLAG_SEND_FLUSH is set within the transmission flags, as otherwise NBD_CMD_FLUSH will never be sent by the client to the server.

  • A client which uses multiple connections to a server to parallelize commands MUST NOT issue an NBD_CMD_FLUSH request until it has received the reply for all write commands which it expects to be covered by the flush.

  • A server MUST NOT reply to a command that has NBD_CMD_FLAG_FUA set in its command flags until the data (if any) written by that command is persisted to non-volatile storage. This only applies if NBD_FLAG_SEND_FUA is set within the transmission flags, as otherwise NBD_CMD_FLAG_FUA will not be set on any commands sent to the server by the client.

NBD_CMD_FLUSH is modelled on the Linux kernel empty bio with REQ_PREFLUSH set. NBD_CMD_FLAG_FUA is modelled on the Linux kernel bio with REQ_FUA set. In case of ambiguity in this specification, the kernel documentation may be useful.

Request message

The request message, sent by the client, looks as follows:

C: 32 bits, 0x25609513, magic (NBD_REQUEST_MAGIC)
C: 16 bits, command flags
C: 16 bits, type
C: 64 bits, handle
C: 64 bits, offset (unsigned)
C: 32 bits, length (unsigned)
C: (length bytes of data if the request is of type NBD_CMD_WRITE)

Reply message

The reply message MUST be sent by the server in response to all requests (save for NBD_CMD_DISC). The message looks as follows:

S: 32 bits, 0x67446698, magic (NBD_REPLY_MAGIC)
S: 32 bits, error (MAY be zero)
S: 64 bits, handle
S: (length bytes of data if the request is of type NBD_CMD_READ)

Terminating the transmission phase

There are two methods of terminating the transmission phase:

  • The client sends NBD_CMD_DISC whereupon the server MUST close down the TLS session (if one is running) and then close the TCP connection. This is referred to as 'initiating a soft disconnect'. Soft disconnects can only be initiated by the client.

  • The client or the server drops the TCP session (in which case it SHOULD shut down the TLS session first). This is referred to as 'initiating a hard disconnect'.

Together these are referred to as 'terminating transmission'.

Either side MAY initiate a hard disconnect if it detects a violation by the other party of a mandatory condition within this document.

On a server shutdown, the server SHOULD wait for inflight requests to be serviced prior to initiating a hard disconnect. A server MAY speed this process up by issuing error replies. The error value issued in respect of these requests and any subsequently received requests SHOULD be ESHUTDOWN.

If the client receives an ESHUTDOWN error it MUST initiate a soft disconnect.

The client MAY issue a soft disconnect at any time, but SHOULD wait until there are no inflight requests first.

The client and the server MUST NOT initiate any form of disconnect other than in one of the above circumstances.

TLS support

The NBD protocol supports Transport Layer Security (TLS) (see RFC5246 as updated by RFC6176 ).

TLS is negotiated with the NBD_OPT_STARTTLS option. This is performed as an in-session upgrade. Below the term 'negotiation' is used to refer to the sending and receiving of NBD options and option replies, and the term 'initiation' of TLS is used to refer to the actual upgrade to TLS.

Certificates, authentication and authorisation

This standard does not specify what encryption, certification and signature algorithms are used. This standard does not specify authentication and authorisation (for instance whether client and/or server certificates are required and what they should contain); this is implementation dependent.

TLS requires fixed newstyle negotiation to have completed.

Server-side requirements

There are three modes of operation for a server. The server MUST support one of these modes.

  • The server operates entirely without TLS ('NOTLS'); OR

  • The server insists upon TLS, and forces the client to upgrade by erroring any NBD options other than NBD_OPT_STARTTLS or NBD_OPT_ABORT with NBD_REP_ERR_TLS_REQD ('FORCEDTLS'); this in practice means that all option negotiation (apart from the NBD_OPT_STARTTLS itself) is carried out with TLS; OR

  • The server provides TLS, and it is mandatory on zero or more exports, and is available at the client's option on all other exports ('SELECTIVETLS'). The server does not force the client to upgrade to TLS during option haggling (as if the client ultimately were to choose a non-TLS-only export, stopping TLS is not possible). Instead it permits the client to upgrade as and when it chooses, but unless an upgrade to TLS has already taken place, the server errors attempts to enter transmission mode on TLS-only exports, MAY refuse to provide information about TLS-only exports via NBD_OPT_INFO, MAY refuse to provide information about non-existent exports via NBD_OPT_INFO, and MAY omit exports that are TLS-only from NBD_OPT_LIST.

The server MAY determine the mode in which it operates dependent upon the session (for instance it might be more liberal with TCP connections made over the loopback interface) but it MUST be consistent in its mode of operation across the lifespan of a single TCP connection to the server. A client MUST NOT assume indications from a prior TCP session to a given server will be relevant to a subsequent session.

The server MUST operate in NOTLS mode unless the server set flag NBD_FLAG_FIXED_NEWSTYLE and the client replied with NBD_FLAG_C_FIXED_NEWSTYLE in the fixed newstyle negotiation.

These modes of operations are described in detail below.

NOTLS mode

If the server receives NBD_OPT_STARTTLS it MUST respond with NBD_REP_ERR_POLICY (if it does not support TLS for policy reasons), NBD_REP_ERR_UNSUP (if it does not support the NBD_OPT_STARTTLS option at all) or another error explicitly permitted by this document. The server MUST NOT respond to any option request with NBD_REP_ERR_TLS_REQD.

FORCEDTLS mode

If the server receives NBD_OPT_STARTTLS prior to negotiating TLS, it MUST reply with NBD_REP_ACK. If the server receives NBD_OPT_STARTTLS when TLS has already been negotiated, it it MUST reply with NBD_REP_ERR_INVALID.

After an NBD_REP_ACK reply has been sent, the server MUST be prepared for a TLS handshake, and all further data MUST be sent and received over TLS. There is no downgrade to a non-TLS session.

As per the TLS standard, the handshake MAY be initiated either by the server (having sent the NBD_REP_ACK) or by the client. If the handshake is unsuccessful (for instance the client's certificate does not match) the server MUST terminate the session as by this stage it is too late to continue without TLS as the acknowledgement has been sent.

If the server receives any other option, including NBD_OPT_INFO and unsupported options, it MUST reply with NBD_REP_ERR_TLS_REQD if TLS has not been initiated; NBD_OPT_INFO is included as in this mode, all exports are TLS-only. If the server receives a request to enter transmission mode via NBD_OPT_EXPORT_NAME when TLS has not been initiated, then as this request cannot error, it MUST terminate the session. If the server receives a request to enter transmission mode via NBD_OPT_GO when TLS has not been initiated, it MUST error with NBD_REP_ERR_TLS_REQD.

The server MUST NOT send NBD_REP_ERR_TLS_REQD in reply to any option if TLS has already been initiated.

The FORCEDTLS mode of operation has an implementation problem in that the client MAY legally simply send a NBD_OPT_EXPORT_NAME to enter transmission mode without previously sending any options. This is avoided by use of NBD_OPT_INFO and NBD_OPT_GO.

SELECTIVETLS mode

If the server receives NBD_OPT_STARTTLS prior to negotiating TLS, it MUST reply with NBD_REP_ACK and initiate TLS as set out under 'FORCEDTLS' above. If the server receives NBD_OPT_STARTTLS when TLS has already been negotiated, it it MUST reply with NBD_REP_ERR_INVALID.

If the server receives NBD_OPT_INFO or NBD_OPT_GO and TLS has not been initiated, it MAY reply with NBD_REP_ERR_TLS_REQD if that export is non-existent, and MUST reply with NBD_REP_ERR_TLS_REQD if that export is TLS-only.

If the server receives a request to enter transmission mode via NBD_OPT_EXPORT_NAME on a TLS-only export when TLS has not been initiated, then as this request cannot error, it MUST terminate the session.

The server MUST NOT send NBD_REP_ERR_TLS_REQD in reply to any option if TLS has already been negotiated. The server MUST NOT send NBD_REP_ERR_TLS_REQD in response to any option other than NBD_OPT_INFO, NBD_OPT_GO and NBD_OPT_EXPORT_NAME, and only in those cases in respect of a TLS-only or non-existent export.

There is a degenerate case of SELECTIVETLS where all exports are TLS-only. This is permitted in part to make programming of servers easier. Operation is a little different from FORCEDTLS, as the client is not forced to upgrade to TLS prior to any options being processed, and the server MAY choose to give information on non-existent exports via NBD_OPT_INFO responses prior to an upgrade to TLS.

Client-side requirements

If the client supports TLS at all, it MUST be prepared to deal with servers operating in any of the above modes. Notwithstanding, a client MAY always terminate the session or refuse to connect to a particular export if TLS is not available and the user requires TLS.

The client MUST NOT issue NBD_OPT_STARTTLS unless the server set flag NBD_FLAG_FIXED_NEWSTYLE and the client replied with NBD_FLAG_C_FIXED_NEWSTYLE in the fixed newstyle negotiation.

The client MUST NOT issue NBD_OPT_STARTTLS if TLS has already been initiated.

Subject to the above two limitations, the client MAY send NBD_OPT_STARTTLS at any time to initiate a TLS session. If the client receives NBD_REP_ACK in response, it MUST immediately upgrade the session to TLS. If it receives NBD_REP_ERR_UNSUP, NBD_REP_ERR_POLICY or any other error in response, it indicates that the server cannot or will not upgrade the session to TLS, and therefore the client MUST either continue the session without TLS, or terminate the session.

A client that prefers to use TLS irrespective of whether the server makes TLS mandatory SHOULD send NBD_OPT_STARTTLS as the first option. This will ensure option haggling is subject to TLS, and will thus prevent the possibility of options being compromised by a Man-in-the-Middle attack. Note that the NBD_OPT_STARTTLS itself may be compromised - see 'downgrade attacks' for more details. For this reason, a client which only wishes to use TLS SHOULD terminate the session if the NBD_OPT_STARTTLS replies with an error.

If the TLS handshake is unsuccessful (for instance the server's certificate does not validate) the client MUST terminate the session as by this stage it is too late to continue without TLS.

If the client receives an NBD_REP_ERR_TLS_REQD in response to any option, it implies that this option cannot be executed unless a TLS upgrade is performed. If the option is any option other than NBD_OPT_INFO or NBD_OPT_GO, this indicates that no option will succeed unless a TLS upgrade is performed; the client MAY therefore choose to issue an NBD_OPT_STARTTLS, or MAY terminate the session (if for instance it does not support TLS or does not have appropriate credentials for this server). If the client receives NBD_REP_ERR_TLS_REQD in response to NBD_OPT_INFO or NBD_OPT_GO this indicates that the export referred to within the option is either non-existent or requires TLS; the client MAY therefore choose to issue an NBD_OPT_STARTTLS, MAY terminate the session (if for instance it does not support TLS or does not have appropriate credentials for this server), or MAY continue in another manner without TLS, for instance by querying or using other exports.

If a client supports TLS, it SHOULD use NBD_OPT_GO (if the server supports it) in place of NBD_OPT_EXPORT_NAME. The reason for this is set out in the final paragraphs of the sections under 'FORCEDTLS' and 'SELECTIVETLS': this gives an opportunity for the server to transmit that an error going into transmission mode is due to the client's failure to initiate TLS, and the fact that the client may obtain information about which exports are TLS-only through NBD_OPT_INFO.

Security considerations

TLS versions

NBD implementations supporting TLS MUST support TLS version 1.2, SHOULD support any later versions. NBD implementations MAY support older versions but SHOULD NOT do so by default (i.e. they SHOULD only be available by a configuration change). Older versions SHOULD NOT be used where there is a risk of security problems with those older versions or of a downgrade attack against TLS versions.

Protocol downgrade attacks

A danger inherent in any scheme relying on the negotiation of whether TLS should be employed is downgrade attacks within the NBD protocol.

There are two main dangers:

  • A Man-in-the-Middle (MitM) hijacks a session and impersonates the server (possibly by proxying it) claiming not to support TLS. In this manner, the client is confused into operating in a plain-text manner with the MitM (with the session possibly being proxied in plain-text to the server using the method below).

  • The MitM hijacks a session and impersonates the client (possibly by proxying it) claiming not to support TLS. In this manner the server is confused into operating in a plain-text manner with the MitM (with the session being possibly proxied to the client with the method above).

With regard to the first, any client that does not wish to be subject to potential downgrade attack SHOULD ensure that if a TLS endpoint is specified by the client, it ensures that TLS is negotiated prior to sending or requesting sensitive data. To recap, the client MAY send NBD_OPT_STARTTLS at any point during option haggling, and MAY terminate the session if NBD_REP_ACK is not provided.

With regard to the second, any server that does not wish to be subject to a potential downgrade attack SHOULD either used FORCEDTLS mode, or should force TLS on those exports it is concerned about using SELECTIVE mode and TLS-only exports. It is not possible to avoid downgrade attacks on exports which may be served either via TLS or in plain text unless the client insists on TLS.

Block size constraints

During transmission phase, several operations are constrained by the export size sent by the final NBD_OPT_EXPORT_NAME or NBD_OPT_GO, as well as by three block size constraints defined here (minimum, preferred, and maximum).

If a client can honour server block size constraints (as set out below and under NBD_INFO_BLOCK_SIZE), it SHOULD announce this during the handshake phase by using NBD_OPT_GO (and NBD_OPT_INFO if used) with an NBD_INFO_BLOCK_SIZE information request, and MUST use NBD_OPT_GO rather than NBD_OPT_EXPORT_NAME (except in the case of a fallback where the server did not support NBD_OPT_INFO or NBD_OPT_GO).

A server with block size constraints other than the default SHOULD advertise the block size constraints during handshake phase via NBD_INFO_BLOCK_SIZE in response to NBD_OPT_INFO or NBD_OPT_GO, and MUST do so unless it has agreed on block size constraints via out of band means.

Some servers are able to make optimizations, such as opening files with O_DIRECT, if they know that the client will obey a particular minimum block size, where it must fall back to safer but slower code if the client might send unaligned requests. For that reason, if a client issues an NBD_OPT_GO including an NBD_INFO_BLOCK_SIZE information request, it MUST abide by the block size constraints it receives. Clients MAY issue NBD_OPT_INFO with NBD_INFO_BLOCK_SIZE to learn the server's constraints without committing to them.

If block size constraints have not been advertised or agreed on externally, then a client SHOULD assume a default minimum block size of 1, a preferred block size of 2^12 (4,096), and a maximum block size of the smaller of the export size or 0xffffffff (effectively unlimited). A server that wants to enforce block sizes other than the defaults specified here MAY refuse to go into transmission phase with a client that uses NBD_OPT_EXPORT_NAME (via a hard disconnect) or which fails to use NBD_INFO_BLOCK_SIZE with NBD_OPT_GO (where the server uses NBD_REP_ERR_BLOCK_SIZE_REQD), although a server SHOULD permit such clients if block size constraints are the default or can be agreed on externally. When allowing such clients, the server MUST cleanly error commands that fall outside block size constraints without corrupting data; even so, this may limit interoperability.

A client MAY choose to operate as if tighter block size constraints had been specified (for example, even when the server advertises the default minimum block size of 1, a client may safely use a minimum block size of 2^9 (512), a preferred block size of 2^16 (65,536), and a maximum block size of 2^25 (33,554,432)). Notwithstanding any maximum block size advertised, either the server or the client MAY initiate a hard disconnect if the size of a request or a reply is large enough to be deemed a denial of service attack.

The minimum block size represents the smallest addressable length and alignment within the export, although writing to an area that small may require the server to use a less-efficient read-modify-write action. If advertised, this value MUST be a power of 2, MUST NOT be larger than 2^16 (65,536), and MAY be as small as 1 for an export backed by a regular file, although the values of 2^9 (512) or 2^12 (4,096) are more typical for an export backed by a block device. If a server advertises a minimum block size, the advertised export size SHOULD be an integer multiple of that block size, since otherwise, the client would be unable to access the final few bytes of the export.

The preferred block size represents the minimum size at which aligned requests will have efficient I/O, avoiding behaviour such as read-modify-write. If advertised, this MUST be a power of 2 at least as large as the smaller of the minimum block size and 2^12 (4,096), although larger values (such as the minimum granularity of a hole) are also appropriate. The preferred block size MAY be larger than the export size, in which case the client is unable to utilize the preferred block size for that export. The server MAY advertise an export size that is not an integer multiple of the preferred block size.

The maximum block size represents the maximum length that the server is willing to handle in one request. If advertised, it MUST be either an integer multiple of the minimum block size or the value 0xffffffff for no inherent limit, MUST be at least as large as the smaller of the preferred block size or export size, and SHOULD be at least 2^25 (33,554,432) if the export is that large, but MAY be something other than a power of 2. For convenience, the server MAY advertise a maximum block size that is larger than the export size, although in that case, the client MUST treat the export size as the effective maximum block size (as further constrained by a nonzero offset).

Where a transmission request can have a nonzero offset and/or length (such as NBD_CMD_READ, NBD_CMD_WRITE, or NBD_CMD_TRIM), the client MUST ensure that offset and length are integer multiples of any advertised minimum block size, and SHOULD use integer multiples of any advertised preferred block size where possible. For those requests, the client MUST NOT use a length larger than any advertised maximum block size or which, when added to offset, would exceed the export size. The server SHOULD report an EINVAL error if the client's request is not aligned to advertised minimum block size boundaries, or is larger than the advertised maximum block size, although the server MAY instead initiate a hard disconnect if a large length could be deemed as a denial of service attack.

Values

This section describes the value and meaning of constants (other than magic numbers) in the protocol.

When flags fields are specified, they are numbered in network byte order.

Handshake phase

Flag fields

Handshake flags

This field of 16 bits is sent by the server after the INIT_PASSWD and the first magic number.

  • bit 0, NBD_FLAG_FIXED_NEWSTYLE; MUST be set by servers that support the fixed newstyle protocol
  • bit 1, NBD_FLAG_NO_ZEROES; if set, and if the client replies with NBD_FLAG_C_NO_ZEROES in the client flags field, the server MUST NOT send the 124 bytes of zero at the end of the negotiation.

The server MUST NOT set any other flags, and SHOULD NOT change behaviour unless the client responds with a corresponding flag. The server MUST NOT set any of these flags during oldstyle negotiation.

Client flags

This field of 32 bits is sent after initial connection and after receiving the handshake flags from the server.

  • bit 0, NBD_FLAG_C_FIXED_NEWSTYLE; SHOULD be set by clients that support the fixed newstyle protocol. Servers MAY choose to honour fixed newstyle from clients that didn't set this bit, but relying on this isn't recommended.
  • bit 1, NBD_FLAG_C_NO_ZEROES; MUST NOT be set if the server did not set NBD_FLAG_NO_ZEROES. If set, the server MUST NOT send the 124 bytes of zeroes at the end of the negotiation.

Clients MUST NOT set any other flags; the server MUST drop the TCP connection if the client sets an unknown flag, or a flag that does not match something advertised by the server.

Transmission flags

This field of 16 bits is sent by the server after option haggling, or immediately after the handshake flags field in oldstyle negotiation.

Many of these flags allow the server to expose to the client which features it understands (in which case they are documented below as "NBD_FLAG_XXX exposes feature YYY"). In each case, the server MAY set the flag for features it supports. The server MUST NOT set the flag for features it does not support. The client MUST NOT use a feature documented as 'exposed' by a flag unless that flag was set.

The field has the following format:

  • bit 0, NBD_FLAG_HAS_FLAGS: MUST always be 1.
  • bit 1, NBD_FLAG_READ_ONLY: The server MAY set this flag to indicate to the client that the export is read-only (exports might be read-only in a manner undetectable to the server, for instance because of permissions). If this flag is set, the server MUST error subsequent write operations to the export.
  • bit 2, NBD_FLAG_SEND_FLUSH: exposes support for NBD_CMD_FLUSH.
  • bit 3, NBD_FLAG_SEND_FUA: exposes support for NBD_CMD_FLAG_FUA.
  • bit 4, NBD_FLAG_ROTATIONAL: the server MAY set this flag to 1 to inform the client that the export has the characteristics of a rotational medium, and the client MAY schedule I/O accesses in a manner corresponding to the setting of this flag.
  • bit 5, NBD_FLAG_SEND_TRIM: exposes support for NBD_CMD_TRIM.
  • bit 6, NBD_FLAG_SEND_WRITE_ZEROES: exposes support for NBD_CMD_WRITE_ZEROES and NBD_CMD_FLAG_NO_HOLE.
  • bit 7, NBD_FLAG_SEND_DF: defined by the experimental STRUCTURED_REPLY extension.
  • bit 8, NBD_FLAG_CAN_MULTI_CONN: Indicates that the server operates entirely without cache, or that the cache it uses is shared among all connections to the given device. In particular, if this flag is present, then the effects of NBD_CMD_FLUSH and NBD_CMD_FLAG_FUA MUST be visible across all connections when the server sends its reply to that command to the client. In the absense of this flag, clients SHOULD NOT multiplex their commands over more than one connection to the export.
  • bit 9, NBD_FLAG_SEND_RESIZE: exposes support for NBD_CMD_RESIZE.

Clients SHOULD ignore unknown flags.

Option types

These values are used in the "option" field during the option haggling of the newstyle negotiation.

  • NBD_OPT_EXPORT_NAME (1)

    Choose the export which the client would like to use, end option haggling, and proceed to the transmission phase.

    Data: String, name of the export, as free-form text. The length of the name is determined from the option header. If the chosen export does not exist or requirements for the chosen export are not met (e.g., the client did not initiate TLS for an export where the server requires it), the server MUST terminate the session.

    A special, "empty", name (i.e., the length field is zero and no name is specified), is reserved for a "default" export, to be used in cases where explicitly specifying an export name makes no sense.

    This is the only valid option in nonfixed newstyle negotiation. A server which wishes to use any other option MUST support fixed newstyle.

    A major problem of this option is that it does not support the return of error messages to the client in case of problems. To remedy this, NBD_OPT_GO has been introduced (see below). A client thus SHOULD use NBD_OPT_GO in preference to NBD_OPT_EXPORT_NAME but SHOULD fall back to NBD_OPT_EXPORT_NAME if NBD_OPT_GO is not supported (not falling back will prevent it from connecting to old servers).

  • NBD_OPT_ABORT (2)

    The client desires to abort the negotiation and terminate the session. The server MUST reply with NBD_REP_ACK.

    The client SHOULD NOT send any additional data with the option; however, a server SHOULD ignore any data sent by the client rather than rejecting the request as invalid.

    Previous versions of this document were unclear on whether the server should send a reply to NBD_OPT_ABORT. Therefore the client SHOULD gracefully handle the server closing the connection after receiving an NBD_OPT_ABORT without it sending a reply. Similarly the server SHOULD gracefully handle the client sending an NBD_OPT_ABORT and closing the connection without waiting for a reply.

  • NBD_OPT_LIST (3)

    Return zero or more NBD_REP_SERVER replies, one for each export, followed by NBD_REP_ACK or an error (such as NBD_REP_ERR_SHUTDOWN). The server MAY omit entries from this list if TLS has not been negotiated, the server is operating in SELECTIVETLS mode, and the entry concerned is a TLS-only export.

    The client MUST NOT send any additional data with the option, and the server SHOULD reject a request that includes data with NBD_REP_ERR_INVALID.

  • NBD_OPT_PEEK_EXPORT (4)

    Was defined by the (withdrawn) experimental PEEK_EXPORT extension; not in use.

  • NBD_OPT_STARTTLS (5)

    The client wishes to initiate TLS.

    The client MUST NOT send any additional data with the option. The server MUST either reply with NBD_REP_ACK after which point the connection is upgraded to TLS, or an error reply explicitly permitted by this document (for example, NBD_REP_ERR_INVALID if the client included data).

    See the section on TLS above for further details.

  • NBD_OPT_INFO (6) and NBD_OPT_GO (7)

    Both options have identical formats for requests and replies. The only difference is that after a successful reply to NBD_OPT_GO (i.e. one or more NBD_REP_INFO then an NBD_REP_ACK), transmission mode is entered immediately. Therefore these commands share common documentation.

    NBD_OPT_INFO: The client wishes to get details about an export with the given name for use in the transmission phase, but does not yet want to move to the transmission phase. When successful, this option provides more details than NBD_OPT_LIST, but only for a single export name.

    NBD_OPT_GO: The client wishes to terminate the handshake phase and progress to the transmission phase. This client MAY issue this command after an NBD_OPT_INFO, or MAY issue it without a previous NBD_OPT_INFO. NBD_OPT_GO can thus be used as an improved version of NBD_OPT_EXPORT_NAME that is capable of returning errors.

    Data (both commands):

    • 32 bits, length of name (unsigned); MUST be no larger than the option data length - 6
    • String: name of the export
    • 16 bits, number of information requests
    • 16 bits x n - list of NBD_INFO information requests

    The client MAY list one or more items of specific information it is seeking in the list of information requests, or it MAY specify an empty list. The client MUST NOT include any information request in the list more than once. The server MUST ignore any information requests it does not understand. The server MAY reply to the information requests in any order. The server MAY ignore information requests that it does not wish to supply for policy reasons (other than NBD_INFO_EXPORT). Equally the client MAY refuse to negotiate if not supplied information it has requested. The server MAY send information requests back which are not explicitly requested, but the server MUST NOT assume that such information requests are understood and respected by the client unless the client explicitly asked for them. The client MUST ignore information replies it does not understand.

    If no name is specified (i.e. a zero length string is provided), this specifies the default export (if any), as with NBD_OPT_EXPORT_NAME.

    The server replies with a number of NBD_REP_INFO replies (as few as zero if an error is reported, at least one on success), then concludes the list of information with a final error reply or with a declaration of success, as follows:

    • NBD_REP_ACK: The server accepts the chosen export, and has completed providing information. In this case, the server MUST send at least one NBD_REP_INFO, with an NBD_INFO_EXPORT information type.
    • NBD_REP_ERR_UNKNOWN: The chosen export does not exist on this server. In this case, the server SHOULD NOT send NBD_REP_INFO replies.
    • NBD_REP_ERR_TLS_REQD: The server requires the client to initiate TLS before any revealing any further details about this export. In this case, a FORCEDTLS server MUST NOT send NBD_REP_INFO replies, but a SELECTIVETLS server MAY do so if this is a TLS-only export.
    • NBD_REP_ERR_BLOCK_SIZE_REQD: The server requires the client to request block size constraints using NBD_INFO_BLOCK_SIZE prior to entering transmission phase, because the server will be using non-default block sizes constraints. The server MUST NOT send this error if block size constraints were requested with NBD_INFO_BLOCK_SIZE with the NBD_OPT_INFO or NBD_OPT_GO request. The server SHOULD NOT send this error if it is using default block size constraints or block size constraints negotiated out of band. A server sending an NBD_REP_ERR_BLOCK_SIZE_REQD error SHOULD ensure it first sends an NBD_INFO_BLOCK_SIZE information reply in order to help avoid a potentially unnecessary round trip.

    Additionally, if TLS has not been initiated, the server MAY reply with NBD_REP_ERR_TLS_REQD (instead of NBD_REP_ERR_UNKNOWN) to requests for exports that are unknown. This is so that clients that have not initiated TLS cannot enumerate exports. A SELECTIVETLS server that chooses to hide unknown exports in this manner SHOULD NOT send NBD_REP_INFO replies for a TLS-only export.

    For backwards compatibility, clients SHOULD be prepared to also handle NBD_REP_ERR_UNSUP by falling back to using NBD_OPT_EXPORT_NAME.

    Other errors (such as NBD_REP_ERR_SHUTDOWN) are also possible, as permitted elsewhere in this document, with no constraints on the number of preceeding NBD_REP_INFO.

    If there are no intervening option requests between a successful NBD_OPT_INFO (that is, one where the reply ended with a final NBD_REP_ACK) and an NBD_OPT_GO with the same parameters (including the list of information items requested), then the server MUST reply with the same set of information, such as transmission flags in the NBD_INFO_EXPORT reply, although the ordering of the intermediate NBD_REP_INFO messages MAY differ. Otherwise, due to the intervening option requests or the use of different parameters, the server MAY send different data in the successful response, and/or MAY fail the second request.

    The reply to an NBD_OPT_GO is identical to the reply to NBD_OPT_INFO save that if the reply indicates success (i.e. ends with NBD_REP_ACK), the client and the server both immediately enter the transmission phase. The server MUST NOT send any zero padding bytes after the NBD_REP_ACK data, whether or not the client negotiated the NBD_FLAG_C_NO_ZEROES flag. The client MUST NOT send further option requests unless the final reply from the server indicates an error.

  • NBD_OPT_GO (7)

    See above under NBD_OPT_INFO.

  • NBD_OPT_STRUCTURED_REPLY (8)

    Defined by the experimental STRUCTURED_REPLY extension.

  • NBD_OPT_LIST_META_CONTEXT (9)

    Defined by the experimental BLOCK_STATUS extension.

  • NBD_OPT_SET_META_CONTEXT (10)

    Defined by the experimental BLOCK_STATUS extension.

Option reply types

These values are used in the "reply type" field, sent by the server during option haggling in the fixed newstyle negotiation.

  • NBD_REP_ACK (1)

    Will be sent by the server when it accepts the option and no further information is available, or when sending data related to the option (in the case of NBD_OPT_LIST) has finished. No data.

  • NBD_REP_SERVER (2)

    A description of an export. Data:

    • 32 bits, length of name (unsigned); MUST be no larger than the reply packet header length - 4
    • String, name of the export, as expected by NBD_OPT_EXPORT_NAME, NBD_OPT_INFO, or NBD_OPT_GO
    • If length of name < (reply packet header length - 4), then the rest of the data contains some implementation-specific details about the export. This is not currently implemented, but future versions of nbd-server may send along some details about the export. Therefore, unless explicitly documented otherwise by a particular client request, this field is defined to be a string suitable for direct display to a human being.

  • NBD_REP_INFO (3)

    A detailed description about an aspect of an export. The response to NBD_OPT_INFO and NBD_OPT_GO includes zero or more of these messages prior to a final error reply, or at least one before an NBD_REP_ACK reply indicating success. The server MUST send an NBD_INFO_EXPORT information type at some point before sending an NBD_REP_ACK, so that NBD_OPT_GO can provide a superset of the information given in response to NBD_OPT_EXPORT_NAME; all other information types are optional. A particular information type SHOULD only appear once for a given export unless documented otherwise.

    A client MUST NOT rely on any particular ordering amongst the NBD_OPT_INFO replies, and MUST ignore information types that it does not recognize.

    The acceptable values for the header length field are determined by the information type, and includes the 2 bytes for the type designator, in the following general layout:

    • 16 bits, information type (e.g. NBD_INFO_EXPORT)
    • length - 2 bytes, information payload

    The following information types are defined:

    • NBD_INFO_EXPORT (0)

      Mandatory information before a successful completion of NBD_OPT_INFO or NBD_OPT_GO. Describes the same information that is sent in response to the older NBD_OPT_EXPORT_NAME, except that there are no trailing zeroes whether or not NBD_FLAG_C_NO_ZEROES was negotiated. length MUST be 12, and the reply payload is interpreted as follows:

      • 16 bits, NBD_INFO_EXPORT
      • 64 bits, size of the export in bytes (unsigned)
      • 16 bits, transmission flags

    • NBD_INFO_NAME (1)

      Represents the server's canonical name of the export. The name MAY differ from the name presented in the client's option request, and the information item MAY be omitted if the client option request already used the canonical name. This information type represents the same name that would appear in the name portion of an NBD_REP_SERVER in response to NBD_OPT_LIST. The length MUST be at least 2, and the reply payload is interpreted as:

      • 16 bits, NBD_INFO_NAME
      • String: name of the export, length - 2 bytes

    • NBD_INFO_DESCRIPTION (2)

      A description of the export, suitable for direct display to the human being. This information type represents the same optional description that may appear after the name portion of an NBD_REP_SERVER in response to NBD_OPT_LIST. The length MUST be at least 2, and the reply payload is interpreted as:

      • 16 bits, NBD_INFO_DESCRIPTION
      • String: description of the export, length - 2 bytes

    • NBD_INFO_BLOCK_SIZE (3)

      Represents the server's advertised block size constraints; see the "Block size constraints" section for more details on what these values represent, and on constraints on their values. The server MUST send this info if it is requested and it intends to enforce block size constraints other than the defaults. After sending this information in response to an NBD_OPT_GO in which the client specifically requested NBD_INFO_BLOCK_SIZE, the server can legitimately assume that any client that continues the session will support the block size constraints supplied (note that this assumption cannot be made solely on the basis of an NBD_OPT_INFO with an NBD_INFO_BLOCK_SIZE request, or an NBD_OPT_GO without an explicit NBD_INFO_BLOCK_SIZE request). The length MUST be 14, and the reply payload is interpreted as:

      • 16 bits, NBD_INFO_BLOCK_SIZE
      • 32 bits, minimum block size
      • 32 bits, preferred block size
      • 32 bits, maximum block size

  • NBD_REP_META_CONTEXT (4)

    Defined by the experimental BLOCK_STATUS extension.

There are a number of error reply types, all of which are denoted by having bit 31 set. All error replies MAY have some data set, in which case that data is an error message string suitable for display to the user.

  • NBD_REP_ERR_UNSUP (2^31 + 1)

    The option sent by the client is unknown by this server implementation (e.g., because the server is too old, or from another source).

  • NBD_REP_ERR_POLICY (2^31 + 2)

    The option sent by the client is known by this server and syntactically valid, but server-side policy forbids the server to allow the option (e.g., the client sent NBD_OPT_LIST but server configuration has that disabled)

  • NBD_REP_ERR_INVALID (2^31 + 3)

    The option sent by the client is known by this server, but was determined by the server to be syntactically or semantically invalid. For instance, the client sent an NBD_OPT_LIST with nonzero data length, or the client sent a second NBD_OPT_STARTTLS after TLS was already negotiated.

  • NBD_REP_ERR_PLATFORM (2^31 + 4)

    The option sent by the client is not supported on the platform on which the server is running. Not currently used.

  • NBD_REP_ERR_TLS_REQD (2^31 + 5)

    The server is unwilling to continue negotiation unless TLS is initiated first. In the case of NBD_OPT_INFO and NBD_OPT_GO this unwillingness MAY (depending on the TLS mode) be limited to the export in question. See the section on TLS above for further details.

  • NBD_REP_ERR_UNKNOWN (2^31 + 6)

    The requested export is not available.

  • NBD_REP_ERR_SHUTDOWN (2^31 + 7)

    The server is unwilling to continue negotiation as it is in the process of being shut down.

  • NBD_REP_ERR_BLOCK_SIZE_REQD (2^31 + 8)

    The server is unwilling to enter transmission phase for a given export unless the client first acknowledges (via NBD_INFO_BLOCK_SIZE) that it will obey non-default block sizing requirements.

  • NBD_REP_ERR_TOO_BIG (2^31 + 9)

    Defined by the experimental BLOCK_STATUS extension.

Transmission phase

Command flags

This field of 16 bits is sent by the client with every request and provides additional information to the server to execute the command. Refer to the "Request types" section below for more details about how a given flag affects a particular command. Clients MUST NOT set a command flag bit that is not documented for the particular command; and whether a flag is valid may depend on negotiation during the handshake phase.

  • bit 0, NBD_CMD_FLAG_FUA; This flag is valid for all commands, provided NBD_FLAG_SEND_FUA has been negotiated, in which case the server MUST accept all commands with this bit set (even by ignoring the bit). The client SHOULD NOT set this bit unless the command has the potential of writing data (current commands are NBD_CMD_WRITE, NBD_CMD_WRITE_ZEROES and NBD_CMD_TRIM), however note that existing clients are known to set this bit on other commands. Subject to that, and provided NBD_FLAG_SEND_FUA is negotiated, the client MAY set this bit on all, no or some commands as it wishes (see the section on Ordering of messages and writes for details). If the server receives a command with NBD_CMD_FLAG_FUA set it MUST NOT send its reply to that command until all write operations (if any) associated with that command have been completed and persisted to non-volatile storage. If the command does not in fact write data (for instance on an NBD_CMD_TRIM in a situation where the command as a whole is ignored), the server MAY ignore this bit being set on such a command.
  • bit 1, NBD_CMD_FLAG_NO_HOLE; valid during NBD_CMD_WRITE_ZEROES. SHOULD be set to 1 if the client wants to ensure that the server does not create a hole. The client MAY send NBD_CMD_FLAG_NO_HOLE even if NBD_FLAG_SEND_TRIM was not set in the transmission flags field. The server MUST support the use of this flag if it advertises NBD_FLAG_SEND_WRITE_ZEROES.
  • bit 2, NBD_CMD_FLAG_DF; defined by the experimental STRUCTURED_REPLY extension.
  • bit 3, NBD_CMD_FLAG_REQ_ONE; defined by the experimental BLOCK_STATUS extension.

Request types

The following request types exist:

  • NBD_CMD_READ (0)

    A read request. Length and offset define the data to be read. The client SHOULD NOT request a read length of 0; the behavior of a server on such a request is unspecified although the server SHOULD NOT disconnect.

    The server MUST reply with a reply header, followed immediately by length bytes of data, read from offset bytes into the file, unless an error condition has occurred.

    If an error occurs, the server SHOULD set the appropriate error code in the error field. The server MAY then initiate a hard disconnect. If it chooses not to, it MUST NOT send any payload for this request.

    If an error occurs while reading after the server has already sent out the reply header with an error field set to zero (i.e., signalling no error), the server MUST immediately initiate a hard disconnect; it MUST NOT send any further data to the client.

  • NBD_CMD_WRITE (1)

    A write request. Length and offset define the location and amount of data to be written. The client MUST follow the request header with length number of bytes to be written to the device. The client SHOULD NOT request a write length of 0; the behavior of a server on such a request is unspecified although the server SHOULD NOT disconnect.

    The server MUST write the data to disk, and then send the reply message. The server MAY send the reply message before the data has reached permanent storage.

    If an error occurs, the server MUST set the appropriate error code in the error field.

  • NBD_CMD_DISC (2)

    A disconnect request. The server MUST handle all outstanding requests, shut down the TLS session (if one is running), and close the TCP session. A client MUST NOT send anything to the server after sending an NBD_CMD_DISC command.

    The values of the length and offset fields in a disconnect request MUST be zero.

    There is no reply to an NBD_CMD_DISC.

  • NBD_CMD_FLUSH (3)

    A flush request. The server MUST NOT send a successful reply header for this request before all write requests for which a reply has already been sent to the client have reached permanent storage (using fsync() or similar).

    A client MUST NOT send a flush request unless NBD_FLAG_SEND_FLUSH was set in the transmission flags field.

    For a flush request, length and offset are reserved, and MUST be set to all-zero.

  • NBD_CMD_TRIM (4)

    A hint to the server that the data defined by length and offset is no longer needed. A server MAY discard length bytes starting at offset, but is not required to; and MAY round offset up and length down to meet internal alignment constraints so that only a portion of the client's request is actually discarded. The client SHOULD NOT request a trim length of 0; the behavior of a server on such a request is unspecified although the server SHOULD NOT disconnect.

    After issuing this command, a client MUST NOT make any assumptions about the contents of the export affected by this command, until overwriting it again with NBD_CMD_WRITE or NBD_CMD_WRITE_ZEROES.

    A client MUST NOT send a trim request unless NBD_FLAG_SEND_TRIM was set in the transmission flags field.

  • NBD_CMD_WRITE_ZEROES (6)

    A write request with no payload. Offset and length define the location and amount of data to be zeroed. The client SHOULD NOT request a write length of 0; the behavior of a server on such a request is unspecified although the server SHOULD NOT disconnect.

    The server MUST zero out the data on disk, and then send the reply message. The server MAY send the reply message before the data has reached permanent storage.

    A client MUST NOT send a write zeroes request unless NBD_FLAG_SEND_WRITE_ZEROES was set in the transmission flags field.

    By default, the server MAY use trimming to zero out the area, even if it did not advertise NBD_FLAG_SEND_TRIM; but it MUST ensure that the data reads back as zero. However, the client MAY set the command flag NBD_CMD_FLAG_NO_HOLE to inform the server that the area MUST be fully provisioned, ensuring that future writes to the same area will not cause fragmentation or cause failure due to insufficient space.

    If an error occurs, the server MUST set the appropriate error code in the error field.

    The server SHOULD return ENOSPC if it receives a write zeroes request including one or more sectors beyond the size of the device. It SHOULD return EPERM if it receives a write zeroes request on a read-only export.

  • NBD_CMD_BLOCK_STATUS (7)

    Defined by the experimental BLOCK_STATUS extension.

  • NBD_CMD_RESIZE (8)

    A resize request. The server should make the necessary changes by either allocating more space or releasing space that is no longer necessary in order to support the new size, and then send the reply message. For the purpose of this message, the field offset in the request header is used to signal the new requested size.

    If an error occurs, the server SHOULD reply with one of the following error codes:

    • EPERM: server configuration does not allow this reply, or other clients are also using the same export and the request was for a smaller size. The latter is optional; servers are not required to keep track of all clients using an export, and clients issuing resize requests should make sure not to issue it unless they are the only writer. At any rate, if this error is not issued, the new device size MAY be visible to all clients or just to the one that issued the resize request.
    • EIO: I/O error occurred while trying to resize the device
    • ENOSPC: the resize was for an increase in space, and requires more space than is available to the server
    • ESHUTDOWN: the server is in the process of being shut down.

    Clients MUST NOT send a resize request unless the NBD_FLAG_SEND_RESIZE flag was set in the transmission flags field.

    If the resize was successful, clients MAY now issue other requests up to the new size as requested in the request header. If the new size is smaller than it was before the request, requests beyond the new size but not beyond the old one MUST fail with ENOSPC, and vice versa.

    Clients MUST NOT issue requests for offsets in the area between the old and new sizes between the time this request is issued and the reply has been received. That is, in case of a "resize smaller" they SHOULD NOT issue requests for offsets beyond the new size, and in case of a "resize larger" they SHOULD NOT issue requests for offsets beyond the old size. The behaviour of servers in respond to clients issuing such requests anyway is not defined by this specification. Additionally, clients MUST also make sure that no such requests are outstanding when the resize request is sent.

  • Other requests

    Some third-party implementations may require additional protocol messages which are not described in this document. In the interest of interoperability, authors of such implementations SHOULD contact the maintainer of this document, so that these messages can be listed here to avoid conflicting implementations.

    Currently one such message is known: NBD_CMD_CACHE, with type set to 5, implemented by xnbd.

Error values

The error values are used for the error field in the reply message. Originally, error messages were defined as the value of errno on the system running the server; however, although they happen to have similar values on most systems, these values are in fact not well-defined, and therefore not entirely portable.

Therefore, the allowed values for the error field have been restricted to set of possibilities. To remain intelligible with older clients, the most common values of errno for that particular error has been chosen as the value for an error.

The following error values are defined:

  • EPERM (1), Operation not permitted.
  • EIO (5), Input/output error.
  • ENOMEM (12), Cannot allocate memory.
  • EINVAL (22), Invalid argument.
  • ENOSPC (28), No space left on device.
  • EOVERFLOW (75), defined in the experimental STRUCTURED_REPLY extension.
  • ESHUTDOWN (108), Server is in the process of being shut down.

The server SHOULD return ENOSPC if it receives a write request including one or more sectors beyond the size of the device. It also SHOULD map the EDQUOT and EFBIG errors to ENOSPC. It SHOULD return EINVAL if it receives a read or trim request including one or more sectors beyond the size of the device, or if a read or write request is not aligned to advertised minimum block sizes. Finally, it SHOULD return EPERM if it receives a write or trim request on a read-only export.

The server SHOULD return EINVAL if it receives an unknown command.

The server SHOULD return EINVAL if it receives an unknown command flag. It also SHOULD return EINVAL if it receives a request with a flag not explicitly documented as applicable to the given request.

Which error to return in any other case is not specified by the NBD protocol.

The server SHOULD NOT return ENOMEM if at all possible.

Experimental extensions

In addition to the normative elements of the specification set out herein, various experimental non-normative extensions have been proposed. These may not be implemented in any known server or client, and are subject to change at any point. A full implementation may require changes to the specifications, or cause the specifications to be withdrawn altogether.

These experimental extensions are set out in git branches starting with names starting with the word 'extension'.

Currently known are:

Implementors of these extensions are strongly suggested to contact the mailinglist in order to help fine-tune the specifications before committing to a particular implementation.

Those proposing further extensions should also contact the mailinglist. It is possible to reserve command codes etc. within this document for such proposed extensions. Aside from that, extensions are written as branches which can be merged into master if and when those extensions are promoted to the normative version of the document in the master branch.

About this file

This file tries to document the NBD protocol as it is currently implemented in the Linux kernel and in the reference implementation. The purpose of this file is to allow people to understand the protocol without having to read the code. However, the description above does not come with any form of warranty; while every effort has been taken to avoid them, mistakes are possible.

In contrast to the other files in this repository, this file is not licensed under the GPLv2. To the extent possible by applicable law, I hereby waive all copyright and related or neighboring rights to this file and release it into the public domain.

The purpose of releasing this into the public domain is to allow competing implementations of the NBD protocol without those implementations being considered derivative implementations; but please note that changing this document, while allowed by its public domain status, does not make an incompatible implementation suddenly speak the NBD protocol.