Klipper + FLUIDD >> FLSUN_Q5

Config and calibration Printer£D Delta FLSun Q5

################### HW MOD ####################

• Phaetus Dragon Voron HotEnd HF
• MKS Robin Nano v1.2 + 4x BigTrhhTech 2208
• Raspberry Pi Zero 2 W
• Display TFT 3.5" "https://github.com/CytronTechnologies/xpt2046-LCD-Driver-for-Raspberry-Pi"
• New EFFECTOR-Block (STL + Fusion360_Project) "file: Effector-Base_FLSUN Q5v1.f3z"
• Capricorn Tube
• Toaiot Magnetic Bed PEI
• Extruder Dual Drive v2
• FAN Noctua 40x40
• Led-Strip in towers 2835 24v
• RaspberryCam FullHD

################### SW MOD #####################

• Klipper v0.10.0-184
• Fluidd v1.16.2
• Moonraker v0.7.1-243
• KlipperScreen v0.2.0-10

################## Install by KIAUH #################

URL: https://github.com/th33xitus/kiauh

###############################################

Calibration FLSUN Q5:

PREREQUISITES:

BEFORE :

• Install SW [Klipper + Fluidd + Moonraker in RaspberryDistro]
• Calibrating the DeltaPrint-Geometry, carry out a correct calibration of the extruder!!!

STEP 1:

• Import "printer [Pre-Calibration].cfg" and rename in "printer.cfg"
• Save and Reboot Klippy

STEP 2:

• Run command "PROBE_CALIBRATE" [with sensor installed]
• Fine tuning with Paper method using TESTZ after removing the probe. [ex. "TESTZ Z=-10" etc.]
• ACCEPT and SAVE_CONFIG

STEP 3:

• Run command "DELTA_CALIBRATE"
• SAVE_CONFIG

STEP 4:

• Print "Calibration Hex 1.STL"
• After printing, keep the bed warm -> GCODE Command: "M140 S60"
• Measure and compile excel-file: 1 - "Klipper Enhanced Delta Calibration.xlsx"
• Command sequence:

• DELTA_ANALYZE CENTER......

• DELTA_ANALYZE OUTER_DISTS.....

• DELTA_ANALYZE CENTER_PILLAR_WIDTHS.....

• DELTA_ANALYZE OUTER_PILLAR_WIDTHS.....

• DELTA_ANALYZE CALIBRATE=extended

• SAVE_CONFIG

STEP 5:

• Print "Calibration Hex 2.STL"
• After printing, keep the bed warm -> GCODE Command: "M140 S60"
• Measure and compile excel-file: 1 - "2 - Calibration_Calculus.xlsx"
• After filling out the sheet, change the "arm length" parameters at the bottom of the file: printer.cfg

//========================================================================== //========================================================================== //==========================================================================

• #*# <---------------------- SAVE_CONFIG ----------------------->
• #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
• #*# [stepper_a]
• #*# angle = 210.481232
• #*# arm_length = 217.425939 ####################### Fine Tuning parameter
• #*# position_endstop = 218.724820
• #*#
• #*# [stepper_b]
• #*# angle = 330.925002
• #*# arm_length = 216.095900 ####################### Fine Tuning parameter
• #*# position_endstop = 219.438345
• #*#
• #*# [stepper_c]
• #*# angle = 90.000000
• #*# arm_length = 215.670200 ####################### Fine Tuning parameter
• #*# position_endstop = 218.763895

//========================================================================== //========================================================================== //==========================================================================

//========================================================================== //========================================================================== //==========================================================================