An I2C library for the Teensy 4 microcontroller.
The Teensy 4.0 uses the NXP i.MXRT 1062 microcontroller with an ARM Corex-M7 core.
This library can be used as a drop in replacement for the Wire library in Teensyduino. It has native APIs that are more flexible than Wire and simpler to use in some cases.
The driver implementations, IMX_RT1060_I2CMaster and IMX_RT1060_I2CSlave, have relatively few dependencies on Arduino or the main Teensy libraries. This means that it should be possible to port them to other devices based on the NXP i.MXRT 1060 series of MPUs.
- Supports all features that are required by the I2C Specification for master, multi-master and slave devices.
- Optional drop in replacement for the Wire library in i2c_driver_wire.h
- Master Mode
- Slave Mode
- Standard Mode (100 kbps)
- Fast Mode (400 kbps)
- Fast Mode Plus (1 Mbps)
- Multi-master support
- Clock stretching in Slave Mode
- Non-blocking API for Master Mode and Slave Mode
- Comprehensive error handling
- Can tune the Teensy's electrical configuration for your application
- A single slave can handle multiple I2C addresses
- Glitch filters and line hysteresis in all modes
Version 2 is currently a work in progress. It's available on the dev branch.
You're welcome to use it but expect it to change without notice.
The goal of version 2 is to make the driver more reliable and to support a few more features. See below for a full list of v2 changes.
Please let me know ASAP if your project works Ok with v1 but breaks if you update to v2. This definitely shouldn't happen!
If you're wondering how to get code out of GitHub then you're not alone! Here are some instructions for downloading or cloning this library. The page also explains how to download a different branch.
I2CDevice and I2CRegisterSlave classes make it very simple to follow the standard I2C pattern of reading or writing to "registers". I recommend that you use this interface if it's suitable.
- Download the code and put it in your include path.
- #include "i2c_device.h" if you have a master and wish to read from a slave device.
- #include "i2c_register_slave.h" if you want to implement a slave device to be read by a master.
- See the examples in the examples/simple directory
The driver interfaces are defined in i2c_driver.h. These provide everything you need to use I2C without the limitations of the Wire library. The key classes are I2CMaster and I2CSlave.
- Download the code and put it in your include path.
- #include "imx_rt1060_i2c_driver.h"
- See the examples in the examples/raw directory
Follow these instructions if you have already written code to use Wire.h and don't want to change it. I don't recommend using the Wire API unless you have to.
- Download the code and put it in your include path.
- Change all #includes from Wire.h to i2c_driver_wire.h.
- If any of your dependencies use Wire.h you'll have to modify them to use i2c_driver_wire.h instead.
- If you depend on any libraries that use Wire.h then you'll have to replace all references to Wire.h to i2c_driver_wire.h in that library. This is because Arduino compiles all .cpp files in a library whether you reference them or not.
- See the examples in the examples/wire directory
If you miss a reference to Wire.h then you'll see compilation errors like this:-
... Wire/WireIMXRT.cpp:10: multiple definition of 'Wire'
You may also see linker errors like this:-
... bin/ld.exe: Warning: size of symbol 'Wire' changed from 116 in ... teensy4_i2c\i2c_driver_wire.cpp.o to 112 in ... libraries\Wire\WireIMXRT.cpp.o
This table lists the objects that you should use to handle each I2C port.
| Port | Pins | imx_rt1060_i2c_driver.h | i2c_driver_wire.h |
|---|---|---|---|
| 0 | SCL0(19), SDA0(18) | Master or Slave | Wire |
| 1 | SCL1(16), SDA1(17) | Master1 or Slave1 | Wire1 |
| 2 | SCL2(24), SDA2(25) | Master2 or Slave2 | Wire2 |
The I2C protocol uses open drain pins. The pins can pull signal voltages low, but they cannot pull them high. The system relies on pull up resistors to do this.
This library enables the Teensy's 22 kΩ internal pull up resistor by default. Many breakout boards with I2C have internal pullups as well.
These internal pullups may or may not be sufficient for your application. It depends entirely on the bus capacitance. The more devices you connect to the bus and the longer the wires, the higher the bus capacitance. The only way to be sure is to measure the rise times for your circuit.
See this I2C Underneath article for information about measuring and tuning rise times.
Here are some of the common problems that will can break the I2C connection or just make it very unreliable.
- make sure your wiring has good connections at all times
- you may need external pullup resistors (see above)
- the slave and the master must share a common ground
- if you're upgrading your project from a Teensy 3 with 5V IO to a Teensy 4, and you already have 4.7 kΩ pullup resistors then you may need to swap them to 2.2 kΩ. This is because the Teensy 4 IO pins run at 3.3V.
- make sure the master and the slave agree on how many bytes to send and what order they're in. Data alignment, padding and endianness may cause issues.
- the Teensy's I2C implementation is inherently asynchronous. Watch out for bugs where your application code is reading (or writing) to the buffer that holds your I2C data while the driver is busy transmitting or receiving the data. This causes a device to see part of one message and part of a later message. (A partial read bug).
- https://www.i2c-bus.org/
- I2C Specification Rev. 6
- i.MX RT1062 Datasheet v3
- https://www.nxp.com/docs/en/application-note/AN5078.pdf
- https://www.nxp.com/docs/en/application-note/AN10216.pdf
- I2C Underneath I2C tools etc
- I2C Timing on the i.MX RT1062 (Teensy 4)
- Pin Configuration
- I2C Configuration Design for This Driver
- I2C Timing Calculator
- I2C Scope Simulator
I haven't been able to test some features because of hardware and time restrictions. These features should work but don't be surprised if they don't. Please contact me if you encounter any problems.
- Multi-master configurations
- Clock stretching
The following features are supported by the NXP i.MXRT 1062 processor but I haven't implemented them in this driver. Please contact me if you need any of these features.
- Alternative pins for port 1
- Direct Memory Access (DMA)
- High Speed Mode (3.4 Mbps)
- Ultra Fast Mode (5 Mbps)
- 10 bit slave addresses
- SMBus Alert
- General Call
- 4 pin I2C in Master mode
- Master reading more than 256 bytes in a single transfer
| Version | Release Date | Comment |
|---|---|---|
| v2.0.0-beta.1 | 19th Feb 2023 | Added automated test suite. Tuned electrical settings and timings. See below for details. |
| v1.1.0 | 12th Aug 2020 | I2C slave can now have many I2C addresses. |
| v1.0.1 | 11th Aug 2020 | Adjusted timings to improve responsiveness. |
| v1.0.0 | 19th May 2020 | Promoted v0.9.5 to 1.0 as it seems stable. |
| v0.9.5 | 19th May 2020 | Improved pad control configuration to reduce errors from noise. (Changed default config from 0xF0B0 to 0x1F830) |
| v0.9.4 | 15th May 2020 | Added function overloads to I2CDriverWire to avoid ambiguous calls from existing code. |
| v0.9.3 | 17th February 2020 | I2CDriverWire::requestFrom() now reports correct number of bytes. |
| v0.9.2 | 9th January 2020 | Can now probe for active slaves. |
| v0.9.1 | 7th January 2020 | Fixed bug in i2c_driver_wire.h |
| v0.9.0 | 7th November 2019 | Initial Version |
set_pad_control_configuration()andsetPadControlConfiguration()no longer control the internal pullup resistors. Useset_internal_pullups()andsetInternalPullups()instead.
- glitch filters are now enabled in Slave mode making slave devices more resistant to electrical noise
- significantly adjusted signal timings so driver is compliant with I2C Specification over the full range of allowed rise times
- fixed bug which caused I2CMaster::finished() to return true before STOP was sent to slave.
- you can now enable or disable the internal pullup resistors with
set_internal_pullups()orsetInternalPullups() - reduced pin drive strength which significantly reduced voltage undershoot spikes on falling clock edges
- tested port 2 (pins 24 & 25) on both Teensy 4.1 and Teensy 4.0
- analysed and documented I2C timing registers to find out what they really do (as opposed to what the datasheet claims!)
- created a simulator to predict the effect of changing I2C configuration registers
- created dedicated circuit board to provide tunable pullups and a reliable setup
- created automated tests to check I2C signal timings
- created automated tests of I2CSlave behaviour
- add more automated tests for I2CMaster behaviour