[Shutter] Inverted shutter behaves not like expected #19114

SteWers · 2023-07-14T11:46:57Z

PROBLEM DESCRIPTION

Inverted shutter behaves not like expected.

REQUESTED INFORMATION

{"NAME":"Designator3","GPIO":[0,0,0,0,225,0,0,0,32,224,33,0,544,0],"FLAG":0,"BASE":18}
{"Module":{"0":"Designator3"}}
{"GPIO0":{"0":"None"},"GPIO1":{"0":"None"},"GPIO2":{"0":"None"},"GPIO3":{"0":"None"},"GPIO4":{"225":"Relay2"},"GPIO5":{"0":"None"},"GPIO9":{"0":"None"},"GPIO10":{"0":"None"},"GPIO12":{"32":"Button1"},"GPIO13":{"224":"Relay1"},"GPIO14":{"33":"Button2"},"GPIO15":{"0":"None"},"GPIO16":{"544":"LedLink"},"GPIO17":{"0":"None"}}

If using rules, provide the output of this command: Backlog Rule1; Rule2; Rule3:

No rules

Provide the output of this command: Status 0:

STATUS = {"Status":{"Module":0,"DeviceName":"Tasmota","FriendlyName":["Tasmota",""],"Topic":"Shutter2","ButtonTopic":"0","Power":0,"PowerOnState":3,"LedState":1,"LedMask":"FFFF","SaveData":1,"SaveState":1,"SwitchTopic":"0","SwitchMode":[0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0],"ButtonRetain":0,"SwitchRetain":0,"SensorRetain":0,"PowerRetain":0,"InfoRetain":0,"StateRetain":0,"StatusRetain":0}}
STATUS1 = {"StatusPRM":{"Baudrate":115200,"SerialConfig":"8N1","GroupTopic":"tasmotas","OtaUrl":"http://ota.tasmota.com/tasmota/release/tasmota-DE.bin.gz","RestartReason":"Power On","Uptime":"0T18:32:52","StartupUTC":"2023-07-13T14:14:31","Sleep":50,"CfgHolder":4617,"BootCount":20,"BCResetTime":"2023-01-17T13:07:37","SaveCount":217,"SaveAddress":"F6000"}}
STATUS2 = {"StatusFWR":{"Version":"13.0.0(tasmota)","BuildDateTime":"2023.06.26 10:58:29","Boot":31,"Core":"2_7_4_9","SDK":"2.2.2-dev(38a443e)","CpuFrequency":80,"Hardware":"ESP8266EX","CR":"354/699"}}
STATUS3 = {"StatusLOG":{"SerialLog":2,"WebLog":2,"MqttLog":0,"SysLog":0,"LogHost":"","LogPort":514,"SSId":["JRF-73529421",""],"TelePeriod":300,"Resolution":"558180C0","SetOption":["0000C009","2805C80001000600003C5A0A192800000000","40000080","00006000","00004000","00000000"]}}
STATUS4 = {"StatusMEM":{"ProgramSize":635,"Free":368,"Heap":21,"ProgramFlashSize":1024,"FlashSize":2048,"FlashChipId":"1540C8","FlashFrequency":40,"FlashMode":"DOUT","Features":["00000407","8F9AC787","04368001","000000CF","010013C0","C000F981","00004004","00001000","54000020","00000080"],"Drivers":"1,2,3,4,5,6,7,8,9,10,12,16,18,19,20,21,22,24,26,27,29,30,35,37,45,62,68","Sensors":"1,2,3,4,5,6","I2CDriver":"7"}}
STATUS5 = {"StatusNET":{"Hostname":"Shutter2-4508","IPAddress":"10.100.200.106","Gateway":"10.100.200.1","Subnetmask":"255.255.255.0","DNSServer1":"10.100.200.1","DNSServer2":"0.0.0.0","Mac":"84:CC:A8:B7:F1:9C","Webserver":2,"HTTP_API":1,"WifiConfig":4,"WifiPower":17.0}}
STATUS6 = {"StatusMQT":{"MqttHost":"10.100.200.222","MqttPort":1883,"MqttClientMask":"Shutter2_%06X","MqttClient":"Shutter2_B7F19C","MqttUser":"DVES_USER","MqttCount":1,"MAX_PACKET_SIZE":1200,"KEEPALIVE":30,"SOCKET_TIMEOUT":4}}
STATUS7 = {"StatusTIM":{"UTC":"2023-07-14T08:47:23","Local":"2023-07-14T10:47:23","StartDST":"2023-03-26T02:00:00","EndDST":"2023-10-29T03:00:00","Timezone":99,"Sunrise":"06:01","Sunset":"21:50"}}
STATUS10 = {"StatusSNS":{"Time":"2023-07-14T10:47:23","Shutter1":{"Position":0,"Direction":0,"Target":100,"Tilt":0}}}
STATUS11 = {"StatusSTS":{"Time":"2023-07-14T10:47:23","Uptime":"0T18:32:52","UptimeSec":66772,"Heap":21,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"POWER1":"OFF","POWER2":"OFF","Wifi":{"AP":1,"SSId":"JRF-73529421","BSSId":"09:ab:2F:07:76:15","Channel":6,"Mode":"11n","RSSI":70,"Signal":-65,"LinkCount":1,"Downtime":"0T00:00:05"}}}
STATUS13 = {"StatusSHT":{"SHT0":{"Relay1":1,"Relay2":2,"Open":100,"Close":100,"50perc":50,"Delay":0,"Opt":"0001","Calib":[300,500,700,900,1000],"Mode":"1"}}}

Set weblog to 4 and then, when you experience your issue, provide the output of the Console log:

TO REPRODUCE

Steps to reproduce the behavior:

setup a device as shutter
set ShutterInvert1 1

EXPECTED BEHAVIOUR

When a shutter is used in inverted mode it behaves not like expected. In version 12 everything was OK. I tried to show it in the following table:

Test	ShutterInvert 0	ShutterInvert 1 (expected behavior)	ShutterInvert 1 (real behavior)
Relay 1	open shutter	open shutter	close shutter
Relay 2	close shutter	close shutter	open shutter
Webbutton UP	open shutter	open shutter	closing shutter (Relay 2), slider moves to CLOSE
Webbutton DOWN	close shutter	close shutter	opening shutter (Relay 1), slider moves to OPEN
Slider OPEN	open shutter	open shutter	closing shutter (Relay 2); click on OPEN, when it is OPEN(!?); slider moves to CLOSE
Slider CLOSE	close shutter	close shutter	opening shutter (Relay 1); click on CLOSE, when it is CLOSE(!?); slider moves to OPEN
ShutterOpen	open shutter	open shutter	closing shutter (Relay 2), slider moves to CLOSE
ShutterClose	close shutter	close shutter	opening shutter (Relay 1), slider moves to OPEN
ShutterPosition 100	open shutter	close shutter	opening shutter (Relay 1), slider moves to OPEN
ShutterPosition 0	close shutter	open shutter	closing shutter (Relay 2), slider moves to CLOSE
Reported position when open	100	0	Not clear; slider OPEN -> 0; shutter open -> 100
Reported position when close	0	100	Not clear; slider CLOSE -> 100; shutter close -> 0

The text was updated successfully, but these errors were encountered:

NoName1311 · 2023-07-14T17:38:32Z

For me, the issue also occurs. Version 12.5.0 works as expected.

stefanbode · 2023-08-02T07:55:47Z

uups missed that conversation. Let me check. where is get messed up. The idea of INVERTED that ONLY the reporting 0..100% is inverted. and that shutterposition 20 for example executes a shutterposition 80. There was some updates on the WEBUI that now updates during the move. And the WebUI was not correct with the INVERTED. Let me double check on this.

stefanbode · 2023-08-02T09:52:57Z

When a shutter is used in inverted mode it behaves not like expected. In version 12 everything was OK. I tried to show it in the following table:

Test	ShutterInvert 0	ShutterInvert 1 (expected behavior)	ShutterInvert 1 (real behavior)
Relay 1	open shutter	open shutter	close shutter (fixed/checked)
Relay 2	close shutter	close shutter	open shutter (fixed/checked)
Webbutton UP	open shutter	open shutter	closing shutter (Relay 2), slider moves to CLOSE (fixed/checked)
Webbutton DOWN	close shutter	close shutter	opening shutter (Relay 1), slider moves to OPEN (fixed/checked)
Slider OPEN	open shutter	open shutter	closing shutter (Relay 2); click on OPEN, when it is OPEN(!?); slider moves to CLOSE (fixed/checked)
Slider CLOSE	close shutter	close shutter	opening shutter (Relay 1); click on CLOSE, when it is CLOSE(!?); slider moves to OPEN (fixed/checked)
ShutterOpen	open shutter	open shutter	closing shutter (Relay 2), slider moves to CLOSE (fixed/checked)
ShutterClose	close shutter	close shutter	opening shutter (Relay 1), slider moves to OPEN (fixed/checked)
ShutterPosition 100	open shutter	close shutter	opening shutter (Relay 1), slider moves to OPEN (fixed/checked)
ShutterPosition 0	close shutter	open shutter	closing shutter (Relay 2), slider moves to CLOSE (fixed/checked)
Reported position when open	100	0	Not clear; slider OPEN -> 0; shutter open -> 100 (pls recheck)
Reported position when close	0	100	Not clear; slider CLOSE -> 100; shutter close -> 0 (pls recheck)

SteWers · 2023-08-02T11:48:07Z

At the moment I can't test it, as I am enjoying the sun of Greece instead of the rain in Germany. I'll test it, as soon as I am back.

stefanbode · 2023-08-03T08:28:37Z

At the moment I can't test it, as I am enjoying the sun of Greece instead of the rain in Germany. I'll test it, as soon as I am back.

We can change. I replace you in greece and you can test in rainy, cold germany. Let me know where to go. :-)

SteWers · 2023-08-03T11:20:19Z

We can change. I replace you in greece and you can test in rainy, cold germany. Let me know where to go. :-)

Hmm. 🤔 NO! 😂

stefanbode · 2023-08-08T06:08:09Z

I think we can close this. @SteWers will check after holiday, but I'm confident to pass the test.

SteWers · 2023-08-08T06:20:02Z

I think so, too.

sukram3001 · 2023-08-16T20:34:08Z

Looks like something got lost in the change - see #19328

SteWers · 2023-08-17T09:58:19Z

@stefanbode: I saw you found a bug. The problem from @sukram3001 seem not be present on an ESP8266. But there are a few things, which are till not solved.

In short:

Web buttons are swapped
Clicking on the slider is swapped
Commands ShutterOpen and ShutterClose are swapped

NoName1311 · 2023-09-10T14:39:04Z

@SteWers can you please reopen the issue? I can confirm that this is only partially resolved.

SteWers · 2023-09-10T15:22:04Z

@NoName1311 I think, it's better, when you open a new issue. This is very old, and I cannot see any problems with the last dev on an ESP8266.

stefanbode · 2023-09-11T07:49:52Z

yes open a new one. or just post here on the closed one. Both fine for me to get it fixed

NoName1311 · 2023-09-17T09:22:25Z

I tested it with 13.1.0 and the bugs mentioned above were still there. I will test it again with the next release and then open a new issue if necessary. Thank you for your good work

stefanbode · 2023-09-17T10:58:23Z

Can you please check against the actual development branch. Thx

NoName1311 · 2023-09-23T12:28:35Z

Please excuse my late reply. Today I downloaded and tested the development branch V13.1.0.3. In this version the issue is resolved. Thank you again for the good work.

stueB · 2024-02-14T22:39:08Z

hello there again :) imho this problem is not fully resolved.

my configuration:
tasmota 13.3 on Shelly2PM-ESP32

Interlock ON
SetOption80 1
ShutterMode 1
ShutterRelay1 1
ShutterInvert 1 (or 0)

In your table above "ShutterPosition UP" and "ShutterPosition DOWN" are not mentioned.

expected on ShutterInvert 0 and ShutterInvert 1:

ShutterPosition UP -> Shutter moves to top position
ShutterPosition DOWN -> Shutter moves to lowest position

in my case:

ShutterPosition DOWN resolves in "Command: Error" (regardless of the ShutterInvert Mode and of the current position)
ShutterInvert 0: ShutterPosition UP -> Shutter moves to top position (as expected)
ShutterInvert 1: ShutterPosition UP -> Shutter moves to lowest position (thats wrong imho)

stefanbode · 2024-02-15T11:54:58Z

Regression accepted. Will fix. Up down does not work on inverted shutter

stefanbode · 2024-02-18T11:22:54Z

@stueB : Thanks for bringing it up. A fix is on its way. Pls let me know if you still have issues. Tested on ESP32 and ESP8266

Andi-Coder · 2024-05-23T11:52:55Z

Hello, I have another problem with tasmota 14.0.0, esp8266 and the invert function.
The error occurs when the shutter is fully closed or open (0 or 100) and I try to get the shutter position via the web api "http://device1/cm?cmnd=shutterposition".
No more correct direction MQTT open/close command is executed after the web query anymore.
Only an opposite mqtt command causes a movement.
Example: Shutter is fully open, I query shutterposition through web api and than after that I want to close the shutter through mqtt command. No reaction happed. Only when I send an MQTT open command, but then is the shutter closed.

stefanbode · 2024-05-23T14:00:29Z

Hmm, strange that calling a position screw it all up. Can you attach some log files with loglevel 4. I am on holiday with limited testing equipment. Please do it when shutter is at 30% to get most info.

Andi-Coder · 2024-05-24T11:03:27Z

I've tested a few scenarios. It looks like a web query will always swap the invert function for opening and closing on the first mqtt command.

log.txt

stefanbode · 2024-05-29T14:36:46Z

sorry for the delay. weather was very good on holiday. I found the root cause of the behavior and will work on it. Due to limited testing it will take some time. I was able to reproduce the issue.

stefanbode · 2024-06-10T11:27:03Z

There is a fix submitted a few minutes ago to the DEV branch. Please give it a try. should now work with MQTT

Andi-Coder · 2024-06-14T12:32:35Z

Just tested dev branch. If I now drive to 0, it goes to 100 and vice versa.
log.txt

stefanbode · 2024-06-17T20:04:57Z

Isn't this as it should be?

Andi-Coder · 2024-06-18T05:27:01Z

No, exactly the opposite happens when controlled via MQTT

plu · 2024-06-19T13:51:24Z

Maybe we need some control over which relay does what. So I can configure that relay1 is moving the shutter up, and relay2 is moving the shutter down?

stefanbode · 2024-06-20T08:35:42Z

Be back from holiday and now have access again to the testbench. I can agree that the fix was only one part and need an additional fix. Submitted: #21663

stueB · 2024-10-01T11:31:27Z

@stueB : Thanks for bringing it up. A fix is on its way. Pls let me know if you still have issues. Tested on ESP32 and ESP8266

I’ve finally managed to test it, and it’s been working with no problems with my settup so far.

Unintendedsideeffects · 2024-10-23T09:00:59Z

Great, I am finally the guy from the xkdc comic but I am really interested in having the behavior that was fixed here, any other option to invert the direction of shutterclose and shutteropen, not just the position? Basically the regression was the behavior I needed

stefanbode · 2024-10-27T12:42:33Z

If you just need it revert then simple switch the gpio on relay 1 and 2

Unintendedsideeffects · 2024-10-27T14:39:05Z

Not the avenue for this, maybe I'll write in discussion but physical wiring is inverted and so if you invert Relay 1 and 2 you actually invert button behavior, shutterinvert seemed the correct solution

…

On Sun, Oct 27, 2024, 1:42 PM stefanbode ***@***.***> wrote: If you just need it revert them simple change relay 1 and 2 — Reply to this email directly, view it on GitHub <#19114 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ADMW7EGXZAJ3SJM65N3EUIDZ5TGT7AVCNFSM6AAAAAA2KHCWNWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDINBQGAYDAOBUGU> . You are receiving this because you commented.Message ID: ***@***.***>

stefanbode · 2024-10-28T05:41:17Z

Maybe you write down what is your actual configuration and what do you want to archive. Relay 1 is up and 2 is down. This is mandatory. Is it is mounted in the wall and you cannot change them just flip the gpio on the configuration page. Now shutterclose and open should do what you want. If your integration now has a problem if 0 or 100 is required for the open position then use Shutterinvert. That's all you need.

Jason2866 mentioned this issue Jul 16, 2023

No shutter support any more since update from 12.1.1 to 13.0.0 #19125

Closed

stefanbode mentioned this issue Aug 2, 2023

Fixing SHUTTERINVERT issues #19243

Merged

6 tasks

SteWers closed this as completed Aug 8, 2023

stefanbode mentioned this issue Feb 18, 2024

fix issue on inverted shutters with commands comming with shutterposition #20752

Merged

6 tasks

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

[Shutter] Inverted shutter behaves not like expected #19114

[Shutter] Inverted shutter behaves not like expected #19114

SteWers commented Jul 14, 2023

NoName1311 commented Jul 14, 2023

stefanbode commented Aug 2, 2023

stefanbode commented Aug 2, 2023

SteWers commented Aug 2, 2023

stefanbode commented Aug 3, 2023

SteWers commented Aug 3, 2023

stefanbode commented Aug 8, 2023

SteWers commented Aug 8, 2023

sukram3001 commented Aug 16, 2023

SteWers commented Aug 17, 2023

NoName1311 commented Sep 10, 2023

SteWers commented Sep 10, 2023

stefanbode commented Sep 11, 2023

NoName1311 commented Sep 17, 2023

stefanbode commented Sep 17, 2023

NoName1311 commented Sep 23, 2023

stueB commented Feb 14, 2024

stefanbode commented Feb 15, 2024

stefanbode commented Feb 18, 2024

Andi-Coder commented May 23, 2024

stefanbode commented May 23, 2024

Andi-Coder commented May 24, 2024 •

edited

Loading

stefanbode commented May 29, 2024

stefanbode commented Jun 10, 2024

Andi-Coder commented Jun 14, 2024

stefanbode commented Jun 17, 2024

Andi-Coder commented Jun 18, 2024

plu commented Jun 19, 2024

stefanbode commented Jun 20, 2024

stueB commented Oct 1, 2024

Unintendedsideeffects commented Oct 23, 2024

stefanbode commented Oct 27, 2024 •

edited

Loading

Unintendedsideeffects commented Oct 27, 2024 via email

stefanbode commented Oct 28, 2024

[Shutter] Inverted shutter behaves not like expected #19114

[Shutter] Inverted shutter behaves not like expected #19114

Comments

SteWers commented Jul 14, 2023

PROBLEM DESCRIPTION

REQUESTED INFORMATION

TO REPRODUCE

EXPECTED BEHAVIOUR

NoName1311 commented Jul 14, 2023

stefanbode commented Aug 2, 2023

stefanbode commented Aug 2, 2023

SteWers commented Aug 2, 2023

stefanbode commented Aug 3, 2023

SteWers commented Aug 3, 2023

stefanbode commented Aug 8, 2023

SteWers commented Aug 8, 2023

sukram3001 commented Aug 16, 2023

SteWers commented Aug 17, 2023

NoName1311 commented Sep 10, 2023

SteWers commented Sep 10, 2023

stefanbode commented Sep 11, 2023

NoName1311 commented Sep 17, 2023

stefanbode commented Sep 17, 2023

NoName1311 commented Sep 23, 2023

stueB commented Feb 14, 2024

expected on ShutterInvert 0 and ShutterInvert 1:

in my case:

stefanbode commented Feb 15, 2024

stefanbode commented Feb 18, 2024

Andi-Coder commented May 23, 2024

stefanbode commented May 23, 2024

Andi-Coder commented May 24, 2024 • edited Loading

stefanbode commented May 29, 2024

stefanbode commented Jun 10, 2024

Andi-Coder commented Jun 14, 2024

stefanbode commented Jun 17, 2024

Andi-Coder commented Jun 18, 2024

plu commented Jun 19, 2024

stefanbode commented Jun 20, 2024

stueB commented Oct 1, 2024

Unintendedsideeffects commented Oct 23, 2024

stefanbode commented Oct 27, 2024 • edited Loading

Unintendedsideeffects commented Oct 27, 2024 via email

stefanbode commented Oct 28, 2024

Andi-Coder commented May 24, 2024 •

edited

Loading

stefanbode commented Oct 27, 2024 •

edited

Loading