Problem: yaml file.

[Hooks321]

Wiki Search Terms

Only new here.

Controller Board

6-pack ESP-WROOM-32

Machine Description

Gantry Laser setup.

Input Circuits

No response

Configuration file

Wont past

Startup Messages

Cannot open configuration file:<your_filename>

User Interface Software

Fluidterm

What happened?

Every time I upload the config yaml file it said the configuration is invalid.??? any help would be great thanks.

GCode File

?

Other Information

?

[breiler]

Can you show the output from the command $SS

[Hooks321]

Hope this helps.

…

On Fri, 26 July 2024, 9:04 pm Joacim Breiler, ***@***.***> wrote: Can you show the output from the command $SS — Reply to this email directly, view it on GitHub <#1272 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AXQPGWHSZZBCMSXEK6F33UDZOIUKLAVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJSGUZDENJQGQ> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[breiler]

Did you try to attach something? That doesn't work when using email - you need to go to the issue to do that: #1272

[Hooks321]

This maybe better.

…

On Fri, 26 July 2024, 9:15 pm Gary Hawkins, ***@***.***> wrote: On Fri, 26 July 2024, 9:13 pm Gary Hawkins, ***@***.***> wrote: > Hope this helps. > > On Fri, 26 July 2024, 9:04 pm Joacim Breiler, ***@***.***> > wrote: > >> Can you show the output from the command $SS >> >> — >> Reply to this email directly, view it on GitHub >> <#1272 (comment)>, >> or unsubscribe >> <https://github.com/notifications/unsubscribe-auth/AXQPGWHSZZBCMSXEK6F33UDZOIUKLAVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJSGUZDENJQGQ> >> . >> You are receiving this because you authored the thread.Message ID: >> ***@***.***> >> >

[Hooks321]

Did that come through?

…

On Fri, 26 July 2024, 9:16 pm Joacim Breiler, ***@***.***> wrote: Did you try to attach something? That doesn't work when using email - you need to go to the issue to do that: #1272 <#1272> — Reply to this email directly, view it on GitHub <#1272 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AXQPGWGDVVVIE65MURIDRETZOIV2RAVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJSGU2DEMJUGU> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[Hooks321]

Sorry for the delay.

[breiler]

The <your_filename> is probably the default setting, select your config file with:
$Config/Filename=Laser Home XYZ (1).yaml

Or you could use the https://installer.fluidnc.com/ go to the "File browser" and click the "Select Config" button:

[Hooks321]

Still trying.

[Hooks321]

OK, selected active config. what do I do next.

[breiler]

Restart the controller and check the boot messages.

If you are doing this from the https://installer.fluidnc.com/ just go to the "Terminal" page and hit "Restart"

[Hooks321]

Hi, looks like its loaded OK now. Thanks for all your help so far, much appreciated. Is there a way for this card to be seen in Lightburn software now.?

[MitchBradley]

Did you search for "lightburn" in the fluidnc wiki?

[Hooks321]

Yes, I found it. Thankyou.

…

On Sat, 27 July 2024, 9:45 am Mitch Bradley, ***@***.***> wrote: Did you search for "lightburn" in the fluidnc wiki? — Reply to this email directly, view it on GitHub <#1272 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AXQPGWFYYYYOIQS2XPNE5RLZOLNQ3AVCNFSM6AAAAABLQICWTSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDENJTGY2TGMJQGE> . You are receiving this because you authored the thread.Message ID: ***@***.***>