[pull] master from torvalds:master

Documentation/ABI/stable/sysfs-driver-dma-idxd

@@ -1,3 +1,9 @@
+What:		sys/bus/dsa/devices/dsa<m>/version
+Date:		Apr 15, 2020
+KernelVersion:	5.8.0
+Contact:	dmaengine@vger.kernel.org
+Description:	The hardware version number.
+
 What:           sys/bus/dsa/devices/dsa<m>/cdev_major
 Date:           Oct 25, 2019
 KernelVersion: 	5.6.0

Documentation/ABI/testing/sysfs-class-power

@@ -74,6 +74,21 @@ Description:
 		Access: Read, Write
 		Valid values: 0 - 100 (percent)
 
+What:		/sys/class/power_supply/<supply_name>/capacity_error_margin
+Date:		April 2019
+Contact:	linux-pm@vger.kernel.org
+Description:
+		Battery capacity measurement becomes unreliable without
+		recalibration. This values provides the maximum error
+		margin expected to exist by the fuel gauge in percent.
+		Values close to 0% will be returned after (re-)calibration
+		has happened. Over time the error margin will increase.
+		100% means, that the capacity related values are basically
+		completely useless.
+
+		Access: Read
+		Valid values: 0 - 100 (percent)
+
 What:		/sys/class/power_supply/<supply_name>/capacity_level
 Date:		June 2009
 Contact:	linux-pm@vger.kernel.org
@@ -190,7 +205,7 @@ Description:
 		Valid values: "Unknown", "Good", "Overheat", "Dead",
 			      "Over voltage", "Unspecified failure", "Cold",
 			      "Watchdog timer expire", "Safety timer expire",
-			      "Over current"
+			      "Over current", "Calibration required"
 
 What:		/sys/class/power_supply/<supply_name>/precharge_current
 Date:		June 2017
@@ -665,3 +680,31 @@ Description:
 		Valid values:
 		- 1: enabled
 		- 0: disabled
+
+What:		/sys/class/power_supply/<supply_name>/manufacture_year
+Date:		January 2020
+Contact:	linux-pm@vger.kernel.org
+Description:
+		Reports the year (following Gregorian calendar) when the device has been
+		manufactured.
+
+		Access: Read
+		Valid values: Reported as integer
+
+What:		/sys/class/power_supply/<supply_name>/manufacture_month
+Date:		January 2020
+Contact:	linux-pm@vger.kernel.org
+Description:
+		Reports the month when the device has been manufactured.
+
+		Access: Read
+		Valid values: 1-12
+
+What:		/sys/class/power_supply/<supply_name>/manufacture_day
+Date:		January 2020
+Contact:	linux-pm@vger.kernel.org
+Description:
+		Reports the day of month when the device has been manufactured.
+
+		Access: Read
+		Valid values: 1-31

Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt

@@ -8,6 +8,7 @@ Required Properties:
 - compatible: Should be one of:
 	- "mediatek,mt2701-apmixedsys"
 	- "mediatek,mt2712-apmixedsys", "syscon"
+	- "mediatek,mt6765-apmixedsys", "syscon"
 	- "mediatek,mt6779-apmixedsys", "syscon"
 	- "mediatek,mt6797-apmixedsys"
 	- "mediatek,mt7622-apmixedsys"

Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt

@@ -7,6 +7,7 @@ Required Properties:
 
 - compatible: Should be one of:
 	- "mediatek,mt2701-audsys", "syscon"
+	- "mediatek,mt6765-audsys", "syscon"
 	- "mediatek,mt6779-audio", "syscon"
 	- "mediatek,mt7622-audsys", "syscon"
 	- "mediatek,mt7623-audsys", "mediatek,mt2701-audsys", "syscon"

Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt

@@ -6,6 +6,7 @@ The MediaTek camsys controller provides various clocks to the system.
 Required Properties:
 
 - compatible: Should be one of:
+	- "mediatek,mt6765-camsys", "syscon"
 	- "mediatek,mt6779-camsys", "syscon"
 	- "mediatek,mt8183-camsys", "syscon"
 - #clock-cells: Must be 1

Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt

@@ -8,6 +8,7 @@ Required Properties:
 - compatible: Should be one of:
 	- "mediatek,mt2701-imgsys", "syscon"
 	- "mediatek,mt2712-imgsys", "syscon"
+	- "mediatek,mt6765-imgsys", "syscon"
 	- "mediatek,mt6779-imgsys", "syscon"
 	- "mediatek,mt6797-imgsys", "syscon"
 	- "mediatek,mt7623-imgsys", "mediatek,mt2701-imgsys", "syscon"

Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt

@@ -9,6 +9,7 @@ Required Properties:
 - compatible: Should be one of:
 	- "mediatek,mt2701-infracfg", "syscon"
 	- "mediatek,mt2712-infracfg", "syscon"
+	- "mediatek,mt6765-infracfg", "syscon"
 	- "mediatek,mt6779-infracfg_ao", "syscon"
 	- "mediatek,mt6797-infracfg", "syscon"
 	- "mediatek,mt7622-infracfg", "syscon"

Documentation/devicetree/bindings/arm/mediatek/mediatek,mipi0a.txt

@@ -0,0 +1,28 @@
+Mediatek mipi0a (mipi_rx_ana_csi0a) controller
+============================
+
+The Mediatek mipi0a controller provides various clocks
+to the system.
+
+Required Properties:
+
+- compatible: Should be one of:
+	- "mediatek,mt6765-mipi0a", "syscon"
+- #clock-cells: Must be 1
+
+The mipi0a controller uses the common clk binding from
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+The available clocks are defined in dt-bindings/clock/mt*-clk.h.
+
+The mipi0a controller also uses the common power domain from
+Documentation/devicetree/bindings/soc/mediatek/scpsys.txt
+The available power doamins are defined in dt-bindings/power/mt*-power.h.
+
+Example:
+
+mipi0a: clock-controller@11c10000 {
+	compatible = "mediatek,mt6765-mipi0a", "syscon";
+	reg = <0 0x11c10000 0 0x1000>;
+	power-domains = <&scpsys MT6765_POWER_DOMAIN_CAM>;
+	#clock-cells = <1>;
+};

Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt

@@ -9,6 +9,7 @@ Required Properties:
 - compatible: Should be one of:
 	- "mediatek,mt2701-mmsys", "syscon"
 	- "mediatek,mt2712-mmsys", "syscon"
+	- "mediatek,mt6765-mmsys", "syscon"
 	- "mediatek,mt6779-mmsys", "syscon"
 	- "mediatek,mt6797-mmsys", "syscon"
 	- "mediatek,mt7623-mmsys", "mediatek,mt2701-mmsys", "syscon"

Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.yaml

@@ -20,6 +20,7 @@ properties:
         - enum:
           - mediatek,mt2701-pericfg
           - mediatek,mt2712-pericfg
+          - mediatek,mt6765-pericfg
           - mediatek,mt7622-pericfg
           - mediatek,mt7629-pericfg
           - mediatek,mt8135-pericfg

Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt

@@ -8,6 +8,7 @@ Required Properties:
 - compatible: Should be one of:
 	- "mediatek,mt2701-topckgen"
 	- "mediatek,mt2712-topckgen", "syscon"
+	- "mediatek,mt6765-topckgen", "syscon"
 	- "mediatek,mt6779-topckgen", "syscon"
 	- "mediatek,mt6797-topckgen"
 	- "mediatek,mt7622-topckgen"

Documentation/devicetree/bindings/arm/mediatek/mediatek,vcodecsys.txt

@@ -0,0 +1,27 @@
+Mediatek vcodecsys controller
+============================
+
+The Mediatek vcodecsys controller provides various clocks to the system.
+
+Required Properties:
+
+- compatible: Should be one of:
+	- "mediatek,mt6765-vcodecsys", "syscon"
+- #clock-cells: Must be 1
+
+The vcodecsys controller uses the common clk binding from
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+The available clocks are defined in dt-bindings/clock/mt*-clk.h.
+
+The vcodecsys controller also uses the common power domain from
+Documentation/devicetree/bindings/soc/mediatek/scpsys.txt
+The available power doamins are defined in dt-bindings/power/mt*-power.h.
+
+Example:
+
+venc_gcon: clock-controller@17000000 {
+	compatible = "mediatek,mt6765-vcodecsys", "syscon";
+	reg = <0 0x17000000 0 0x10000>;
+	power-domains = <&scpsys MT6765_POWER_DOMAIN_VCODEC>;
+	#clock-cells = <1>;
+};

Documentation/devicetree/bindings/clock/baikal,bt1-ccu-div.yaml

@@ -0,0 +1,188 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2020 BAIKAL ELECTRONICS, JSC
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/baikal,bt1-ccu-div.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Baikal-T1 Clock Control Unit Dividers
+
+maintainers:
+  - Serge Semin <fancer.lancer@gmail.com>
+
+description: |
+  Clocks Control Unit is the core of Baikal-T1 SoC System Controller
+  responsible for the chip subsystems clocking and resetting. The CCU is
+  connected with an external fixed rate oscillator, which signal is transformed
+  into clocks of various frequencies and then propagated to either individual
+  IP-blocks or to groups of blocks (clock domains). The transformation is done
+  by means of an embedded into CCU PLLs and gateable/non-gateable dividers. The
+  later ones are described in this binding. Each clock domain can be also
+  individually reset by using the domain clocks divider configuration
+  registers. Baikal-T1 CCU is logically divided into the next components:
+  1) External oscillator (normally XTAL's 25 MHz crystal oscillator, but
+     in general can provide any frequency supported by the CCU PLLs).
+  2) PLLs clocks generators (PLLs).
+  3) AXI-bus clock dividers (AXI) - described in this binding file.
+  4) System devices reference clock dividers (SYS) - described in this binding
+     file.
+  which are connected with each other as shown on the next figure:
+
+          +---------------+
+          | Baikal-T1 CCU |
+          |   +----+------|- MIPS P5600 cores
+          | +-|PLLs|------|- DDR controller
+          | | +----+      |
+  +----+  | |  |  |       |
+  |XTAL|--|-+  |  | +---+-|
+  +----+  | |  |  +-|AXI|-|- AXI-bus
+          | |  |    +---+-|
+          | |  |          |
+          | |  +----+---+-|- APB-bus
+          | +-------|SYS|-|- Low-speed Devices
+          |         +---+-|- High-speed Devices
+          +---------------+
+
+  Each sub-block is represented as a separate DT node and has an individual
+  driver to be bound with.
+
+  In order to create signals of wide range frequencies the external oscillator
+  output is primarily connected to a set of CCU PLLs. Some of PLLs CLKOUT are
+  then passed over CCU dividers to create signals required for the target clock
+  domain (like AXI-bus or System Device consumers). The dividers have the
+  following structure:
+
+          +--------------+
+  CLKIN --|->+----+ 1|\  |
+  SETCLK--|--|/DIV|->| | |
+  CLKDIV--|--|    |  | |-|->CLKLOUT
+  LOCK----|--+----+  | | |
+          |          |/  |
+          |           |  |
+  EN------|-----------+  |
+  RST-----|--------------|->RSTOUT
+          +--------------+
+
+  where CLKIN is the reference clock coming either from CCU PLLs or from an
+  external clock oscillator, SETCLK - a command to update the output clock in
+  accordance with a set divider, CLKDIV - clocks divider, LOCK - a signal of
+  the output clock stabilization, EN - enable/disable the divider block,
+  RST/RSTOUT - reset clocks domain signal. Depending on the consumer IP-core
+  peculiarities the dividers may lack of some functionality depicted on the
+  figure above (like EN, CLKDIV/LOCK/SETCLK). In this case the corresponding
+  clock provider just doesn't expose either switching functions, or the rate
+  configuration, or both of them.
+
+  The clock dividers, which output clock is then consumed by the SoC individual
+  devices, are united into a single clocks provider called System Devices CCU.
+  Similarly the dividers with output clocks utilized as AXI-bus reference clocks
+  are called AXI-bus CCU. Both of them use the common clock bindings with no
+  custom properties. The list of exported clocks and reset signals can be found
+  in the files: 'include/dt-bindings/clock/bt1-ccu.h' and
+  'include/dt-bindings/reset/bt1-ccu.h'. Since System Devices and AXI-bus CCU
+  are a part of the Baikal-T1 SoC System Controller their DT nodes are supposed
+  to be a children of later one.
+
+if:
+  properties:
+    compatible:
+      contains:
+        const: baikal,bt1-ccu-axi
+
+then:
+  properties:
+    clocks:
+      items:
+        - description: CCU SATA PLL output clock
+        - description: CCU PCIe PLL output clock
+        - description: CCU Ethernet PLL output clock
+
+    clock-names:
+      items:
+        - const: sata_clk
+        - const: pcie_clk
+        - const: eth_clk
+
+else:
+  properties:
+    clocks:
+      items:
+        - description: External reference clock
+        - description: CCU SATA PLL output clock
+        - description: CCU PCIe PLL output clock
+        - description: CCU Ethernet PLL output clock
+
+    clock-names:
+      items:
+        - const: ref_clk
+        - const: sata_clk
+        - const: pcie_clk
+        - const: eth_clk
+
+properties:
+  compatible:
+    enum:
+      - baikal,bt1-ccu-axi
+      - baikal,bt1-ccu-sys
+
+  reg:
+    maxItems: 1
+
+  "#clock-cells":
+    const: 1
+
+  "#reset-cells":
+    const: 1
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - "#clock-cells"
+  - clocks
+  - clock-names
+
+examples:
+  # AXI-bus Clock Control Unit node:
+  - |
+    #include <dt-bindings/clock/bt1-ccu.h>
+
+    clock-controller@1f04d030 {
+      compatible = "baikal,bt1-ccu-axi";
+      reg = <0x1f04d030 0x030>;
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+
+      clocks = <&ccu_pll CCU_SATA_PLL>,
+               <&ccu_pll CCU_PCIE_PLL>,
+               <&ccu_pll CCU_ETH_PLL>;
+      clock-names = "sata_clk", "pcie_clk", "eth_clk";
+    };
+  # System Devices Clock Control Unit node:
+  - |
+    #include <dt-bindings/clock/bt1-ccu.h>
+
+    clock-controller@1f04d060 {
+      compatible = "baikal,bt1-ccu-sys";
+      reg = <0x1f04d060 0x0a0>;
+      #clock-cells = <1>;
+      #reset-cells = <1>;
+
+      clocks = <&clk25m>,
+               <&ccu_pll CCU_SATA_PLL>,
+               <&ccu_pll CCU_PCIE_PLL>,
+               <&ccu_pll CCU_ETH_PLL>;
+      clock-names = "ref_clk", "sata_clk", "pcie_clk",
+                    "eth_clk";
+    };
+  # Required Clock Control Unit PLL node:
+  - |
+    ccu_pll: clock-controller@1f04d000 {
+      compatible = "baikal,bt1-ccu-pll";
+      reg = <0x1f04d000 0x028>;
+      #clock-cells = <1>;
+
+      clocks = <&clk25m>;
+      clock-names = "ref_clk";
+    };
+...