spelling corrections

.wordlist.txt

@@ -57,3 +57,5 @@ SMD
 md
 TODO
 multimeter
+keypress
+MCU

_includes/splinky_preparation.md

@@ -16,7 +16,7 @@ In your kit, you might get either an Elite-C, or a Splinky/RP2040-compatible boa
 {: .warning }
 > Do not install the audio jack and reset button yet.
 > 
-> You will need to prepare one **"Right"** shield pcb, and one **"Left"** - use the legends on the PCB.
+> You will need to prepare one **"Right"** shield PCB, and one **"Left"** - use the legends on the PCB.
 > 
 > We will start with preparing the left side, and after that do the right side.
 
@@ -30,15 +30,15 @@ In your kit, you might get either an Elite-C, or a Splinky/RP2040-compatible boa
 - 12-pin header (x2)
 - 2-pin header
 - shield PCB (left)
-- splinky 
+- Splinky 
 
 {: .warning }
 Make sure to use the "left" shield PCB. Those are not reversible !
 
 {: .warning }
 In the next section, we will install the Splinky onto the shield PCB using the headers. **It is very important to install it on the correct side**, otherwise it will not work. Make sure to look at the pictures carefully ! 
 
-## Left side - Installing the splinky
+## Left side - Installing the Splinky
 
 ![](../assets/pics/guides/splinky/2.jpg)
 
@@ -48,15 +48,15 @@ In the next section, we will install the Splinky onto the shield PCB using the h
 ![](../assets/pics/guides/splinky/3.jpg)
 
 
-- Install the splinky on the headers, using normally-closed pliers to hold it
+- Install the Splinky on the headers, using normally-closed pliers to hold it
 - **Double check against the picture that it is on the correct side**
-- **The text "install elite-c ... on this side" should be covered by the splinky**
+- **The text "install elite-c ... on this side" should be covered by the Splinky**
 
 ![](../assets/pics/guides/splinky/4.jpg)
 
 - **At all times, make sure the Splinky is pressed against the PCB**
 - there should be no gap between the Splinky, the header pins, and the holder PCB
-- Start by soldering the top "5V" and "D0" headers, on the splinky and on the shield (flip the assembly)
+- Start by soldering the top "5V" and "D0" headers, on the Splinky and on the shield (flip the assembly)
 
 ![](../assets/pics/guides/splinky/5.jpg)
 
@@ -65,7 +65,7 @@ In the next section, we will install the Splinky onto the shield PCB using the h
 
 ![](../assets/pics/guides/splinky/6.jpg)
 
-- Solder the 2 bottom "D21" and "D9" headers, on the splinky and the shield (flip the assembly)
+- Solder the 2 bottom "D21" and "D9" headers, on the Splinky and the shield (flip the assembly)
 - Once again, inspect the front of the assembly and make sure that the headers are flush with the Splinky and the shield 
 
 ![](../assets/pics/guides/splinky/7.jpg)
@@ -117,7 +117,7 @@ In this step, we will solder the audio jack. At this point, we will only solder
 - 12-pin header (x2)
 - 2-pin header
 - shield PCB (right)
-- splinky 
+- Splinky 
 
 
 {: .warning }
@@ -128,7 +128,7 @@ In the next section, we will install the Splinky onto the shield PCB using the h
 
 ## Right side - Installing the components
 - Just like previously, install the splinky, reset button, and audio jack onto the shield
-- **The text "install elite-c ... on this side" should be covered by the splinky**
+- **The text "install elite-c ... on this side" should be covered by the Splinky**
 
 
-![](../assets/pics/guides/splinky/13.jpg)
+![](../assets/pics/guides/splinky/13.jpg)

help/troubleshooting.md

@@ -28,7 +28,7 @@ TODO: more, images
 ## The board turns off immediately when I plug in the USB connection!
 
 wow, such short, very fire
-TODO: explain, mention shorts, leds orientation
+TODO: explain, mention shorts, LEDs orientation
 
 ## One or more LEDs don't work!