Skip to content

ccli8/mbed-os-example-pelion

 
 

Repository files navigation

Pelion Device Management Client example for Mbed OS

This is an basic Device Management client example for Mbed OS with the following features:

  • Support for latest Mbed OS and Device Management Client releases.
  • Support for Developer mode provisioning.
  • Support for FW Update.

There is a more advanced example of the client with support for multiple operating systems in mbed-cloud-client-example repository. The underlying client library is the same for both. This Mbed OS only example is simpler as it only supports one OS with a limited set of demonstrated features. If you want to do development in Linux and Mbed OS at the same time - you should use the mbed-cloud-client-example.

Note: If you want to use production provisioning modes, or use more advanced client features, those are demonstrated via mbed-cloud-client-example.

Supported boards

This table shows a list of boards that are supported.

Board Connectivity Storage for credentials and FW candidate Notes
NXP K64F Ethernet Internal Flash
NXP K66F Ethernet Internal Flash
ST NUCLEO_F429ZI Ethernet Internal Flash
ST NUCLEO_F411RE Wi-Fi ESP8266 SD card
Ublox UBLOX_EVK_ODIN_W2 Wi-Fi SD card
ST DISCO_L475VG_IOT01A Wi-Fi QSPIF
Ublox UBLOX_C030_U201 Cellular SD card Build-only
Ublox UBLOX_C030_R412M Cellular SD card Build-only
Embedded Planet EP_AGORA Cellular SPIF Build-only
ST NUCLEO_H743ZI2 Ethernet Internal Flash Build-only
ST NUCLEO_L4R5ZI Wi-Fi ESP8266 Internal Flash Build-only

Build-only = This target is currently verified only via compilation, and is not verified at runtime.

Developer guide

This section is intended for developers to get started, import the example application, compile and get it running on their device.

Requirements

  • Mbed CLI >= 1.10.0

    For instructions on installing and using Mbed CLI, please see our documentation.

  • Install the CLOUD_SDK_API_KEY

    mbed config -G CLOUD_SDK_API_KEY ak_1MDE1...<snip>

    You should generate your own API key. Pelion Device Management is available for any Mbed developer. Create a free trial.

    For instructions on how to generate your API key, please see our documentation.

Deploying

This repository is in the process of being updated and depends on few enhancements being deployed in mbed-cloud-client. In the meantime, follow these steps to import and apply the patches before compiling.

```
mbed import mbed-os-example-pelion
cd mbed-os-example-pelion
```

Compiling

mbed target K64F
mbed toolchain GCC_ARM
mbed device-management init -d arm.com --model-name example-app --force -q
mbed compile

Program Flow

  1. Initialize, connect and register to Pelion DM
  2. Interact with the user through the serial port (115200 bauds)
    • Press enter through putty/minicom to simulate button
    • Press i to print endpoint name
    • Press Ctrl-C to to unregister
    • Press r to reset storage and reboot (warning: it generates a new device ID!)

Further information and requirements

Check the public tutorial for further information:

https://www.pelion.com/docs/device-management/current/connecting/mbed-os.html

Troubleshooting

  • Device initializes but can't register to Pelion

    Error: client_error(3) -> Bootstrap server URL is not correctly formed

    Solution: Format the the storage by pressing 'r' in the serial terminal.

Porting process to add support for an Mbed Enabled board

There are many steps involved in this process. We generally recomend the following steps:

  1. Configure the application using mbed_app.json
    • Configure the default connectivity
    • Configure the KVSTORE area to store credentials (internal or external memory)
    • Build the application, program the board and observe whether the application can connect to Pelion DM by using a serial terminal.
  2. Configure the bootloader using bootloader_app.json
    • Configure the KVSTORE area
    • Configure the FW Candidate Storage
    • Build bootloader application, program the board and observe whether this is able to boot.
  3. Enable application with bootloader using mbed_app.json
    • Enable the usage of the bootloader
    • Ensure the KVSTORE addresses and FW Candidate storage addresses match with the bootloader configuration
    • Build the application again (this time combined with bootloader) and check whether it can boot and connect to Pelion DM.
    • Perform a FW Update and check whether the process can be completed succesfully.

1. Application configuration

Note: consider allocating the credentials on internal flash to simplify the application setup process. In addition, consider the use of internal flash to store the firmware candidate image for the FW update process as this would remove the need to use external components. If there isn't enough space, you may need to enable external storage (SD Card, SPI, etc).

Mbed OS boards should have a default configuration for connectivity and storage in Mbed OS (targets.json). You can extend or override the default configuration using mbed_app.json in this application. Create a new entry under the target name for your device.

a. Connectivity

Specify the default IP connectivity type for your target. It's essential with targets that lack default connectivity set in targets.json or for targets that support multiple connectivity options. For example:

  "target.network-default-interface-type" : "ETHERNET",

The possible options are ETHERNET, WIFI and CELLULAR.

Depending on connectivity type, you might have to specify more configuration options. Review the documentation for further information.

b. Storage for credentials

Start by getting familiar with the multiple storage options and configurations supported in Mbed OS.

Then start designing the system memory map, the location of components (whether they are on internal or external memory), and the corresponding base addresses and sizes. You may want to create a diagram similar to the one below to help you to make design decisions:

+--------------------------+
|                          |
|                          |
|                          |
|Firmware Candidate Storage|
|                          |
|                          |
|                          |
+--------------------------+ <-+ update-client.storage-address
|                          |
|         KVSTORE          |
|                          |
+--------------------------+ <-+ storage_tdb_internal.internal_base_address
|                          |
|        Free space        |
|                          |
+--------------------------+
|                          |
|                          |
|        Active App        |
|                          |
|                          |
|                          |
+--------------------------+ <-+ mbed-bootloader.application-start-address
|Active App Metadata Header|
+--------------------------+ <-+ update-client.application-details
|                          |
|        Bootloader        |
|                          |
+--------------------------+ <-+ 0

In cases where the MCU has two separate memory banks, it's appropiate to allocate the bootloader and base application in one bank, and KVSTORE storage at the begining of the second bank followed by a firmware candidate storage.

  • Option 1: Allocating credentials in internal memory

    This is the preferred option whenever possible. Make sure TDB_INTERNAL is the type of storage selected in mbed_app.json. Specify the base address depending on the available memory in the system. The size of this section should be aligned with the flash erase sector. The value should be multiple of 4 with a minimum of 24KB and upwards depending on the use case (for example the usage of certificate chain will increase the need of storage to hold those certificates). An example of this configuration can be seen for the NUCLEO_F429ZI board in this application.

    "storage.storage_type"                      : "TDB_INTERNAL"
    "storage_tdb_internal.internal_base_address": "(MBED_ROM_START+1024*1024)",
    "storage_tdb_internal.internal_size"        : "(128*1024)",
    
  • Option 2: Allocating credentials in external memory:

    This is possible when the board has an storage device wired to the MCU (could be on-board or external component). Make sure FILESYSTEM is specified as type of storage. The blockdevice and filesystem should be one of the supported in Mbed OS (see docs).

    An example of this configuration can be seen for the K64F board in the mbed-cloud-client-example

    "storage.storage_type"                      : "FILESYSTEM",
    "storage_filesystem.blockdevice"            : "SD",
    "storage_filesystem.filesystem"             : "LITTLE",
    "storage_filesystem.internal_base_address"  : "(32*1024)",
    "storage_filesystem.rbp_internal_size"      : "(8*1024)",
    "storage_filesystem.external_base_address"  : "(0x0)",
    "storage_filesystem.external_size"          : "(1024*1024*64)",
    

c. Storage for firmware updates

Before enabling FW updates, it's recomended that the application is able to initialize the network and connect to Pelion DM.

Once the connection is successfull, you can follow the steps below to enable the board to receive FW updates. Note the configuration for the application in this section should match with the one on the bootloader - see section below.

  • Common configuration

    Regardless of where the firmware candidate is located (internal or external), there is a need to have a bootloader in place. The binary of the booloader can be specified with the bootloader_img option. The address and size of the bootloader determines the application-details and bootloader-details options. The value of bootloader-details can be obtained by checking for the symbol from the map file of the binary. Example python code for obtaining the location:

    with open("BUILD/UBLOX_EVK_ODIN_W2/GCC_ARM/mbed-bootloader.map", 'r') as fd:
        s = fd.read()
    
    regex = r"\.rodata\..*{}\s+(0x[0-9a-fA-F]+)".format("bootloader")
    match = re.search(regex, s, re.MULTILINE)
    offset = int(match.groups()[0], 16)
    print hex(offset)

    Review the mbed-bootloader guidelines on how these options should be selected. Review the bootloader configuration section below for more information.

    Copy the compiled bootloader from mbed-bootloader/BUILDS/<TARGET>/<TOOLCHAIN>-TINY/mbed-bootloader.bin to bootloader/mbed-bootloader-<TARGET>.bin.

    Edit mbed-os-pelion-example/mbed_app.json and modify the target configuration to match with the one in bootloader_app.json.

Note:

  • update-client.application-details should be identical in both bootloader_app.json and mbed_app.json.

  • target.app_offset is relative offset to flash-start-address you specified in mbed_app.json and bootloader_app.json, and is the hex value of the offset specified by application-start-address in bootloader_app.json. For example, (MBED_CONF_APP_FLASH_START_ADDRESS+65*1024) dec equals 0x10400 hex.

  • target.header_offset is also relative offset to the flash-start-address you specified in the bootloader_app.json, and is the hex value of the offset specified by update-client.application-details. For example, (MBED_CONF_APP_FLASH_START_ADDRESS+64*1024) dec equals 0x10000 hex.

An example of this configuration can be seen for the NUCLEO_F429ZI board.

    "update-client.application-details"         : "(MBED_ROM_START + MBED_BOOTLOADER_SIZE)",
    "update-client.bootloader-details"          : "0x08007300",
    "target.bootloader_img"                     : "bootloader/mbed-bootloader-<target>",
    "target.header_offset"                      : "0x8000",
    "target.app_offset"                         : "0x8400",
  • Option 1: Allocating the firmware update candidate in internal memory

    This is the preferred option whenever possible. Make sure ARM_UCP_FLASHIAP is selected in update-storage in mbed_app.json. This area should be located at the end of the flash after the KVSTORE area. Specify the storage-address, storage-size and storage-page as required. The application-details option should point at the end of the bootloader area. An example of this configuration can be seen for the NUCLEO_F429ZI board.

    "mbed-cloud-client.update-storage"          : "ARM_UCP_FLASHIAP",
    "update-client.storage-address"             : "(MBED_CONF_STORAGE_TDB_INTERNAL_INTERNAL_BASE_ADDRESS+MBED_CONF_STORAGE_TDB_INTERNAL_INTERNAL_SIZE)",
    "update-client.storage-size"                : "(1024*1024-MBED_CONF_STORAGE_TDB_INTERNAL_INTERNAL_SIZE)",
    "update-client.storage-page"                : 1,
    
  • Option 2: Allocating the firmware update candidate in external memory

When using an external device to the MCU to store the firmware candidate, make sure ARM_UCP_FLASHIAP_BLOCKDEVICE is specified as type of update-storage. Specify the storage-address, storage-size and storage-page as required.

An example of this configuration can be seen for the K64F board in the mbed-cloud-client-example

    "mbed-cloud-client.update-storage"          : "ARM_UCP_FLASHIAP_BLOCKDEVICE",
    "update-client.storage-address"             : "(1024*1024*64)",
    "update-client.storage-size"                : "((MBED_ROM_START + MBED_ROM_SIZE - APPLICATION_ADDR) * MBED_CONF_UPDATE_CLIENT_STORAGE_LOCATIONS)",

2. Bootloader configuration

The bootloader is required to perform FW Updates. The steps below explain how to create a new configuration and binary for the bootloader.

  1. Import as a new application the mbed-bootloader repository.

  2. Edit the bootloader application configuration in this example (bootloader/bootloader_app.json) and add a new target entry. An example of this configuration can be seen for the NUCLEO_F429ZI board:

    "update-client.firmware-header-version"    : "2",
    "mbed-bootloader.use-kvstore-rot"          : 0,
    "mbed-bootloader.bootloader-size"          : "APPLICATION_SIZE",
    "update-client.application-details"        : "(MBED_ROM_START + MBED_BOOTLOADER_SIZE)",
    "mbed-bootloader.application-start-address": "(MBED_CONF_UPDATE_CLIENT_APPLICATION_DETAILS + MBED_BOOTLOADER_ACTIVE_HEADER_REGION_SIZE)",
    "mbed-bootloader.max-application-size"     : "(MBED_ROM_START + MBED_BOOTLOADER_FLASH_BANK_SIZE - MBED_CONF_MBED_BOOTLOADER_APPLICATION_START_ADDRESS)",
    "update-client.storage-address"            : "(MBED_ROM_START + MBED_BOOTLOADER_FLASH_BANK_SIZE + KVSTORE_SIZE)",
    "update-client.storage-size"               : "(MBED_BOOTLOADER_FLASH_BANK_SIZE - KVSTORE_SIZE)",
    "update-client.storage-locations"          : 1,
    "kvstore-size"                             : "2*64*1024",
    "update-client.storage-page"               : 1
    
  3. Compile the bootloader using the bootloader_app.json configuration you've just edited:

    mbed compile -t <TOOLCHAIN> -m <TARGET> --profile=tiny.json --app-config=.../mbed-os-pelion-example/bootloader/bootloader_app.json>

Note: mbed-bootloader is primarily optimized for GCC_ARM, so you may want to compile it with that toolchain. Before jumping to the next step, you should compile and flash the bootloader and then connect over the virtual serial port to ensure the bootloader is running correctly. You can ignore errors related to checksum verification or failure to jump to application - these are expected at this stage.

Validation and testing for the board configuration

The board needs to pass the underlying Mbed OS tests and be supported by official Mbed OS release.

  cd mbed-os
  mbed test -m <target> -t <toolchain>
  cd mbed-os
  mbed test -t <toolchain> -m <board> -n *integration-* -DINTEGRATION_TESTS -v

Validation and testing for the client configuration

Basic pelion features are required to work:

  • Connects to Pelion in developer mode.
  • Firmware can be updated.
  • Responsive to REST API commands.

This should be verified by executing the Pelion E2E python test library tests.

  • Install the prerequisites listed in the README of the pelion-e2e-python-test-library.

  • Configure your API-key as instructed in the same README.

  • Basic tests can be then executed as:

    pytest TESTS/pelion-e2e-python-test-library/tests/dev-client-tests.py

Note: Future version will bring in also firmware update test as part of the minimum test set..

Known-issues

Please review existing issues on github and report any problem you may see.

About

Mbed OS example of Pelion device management client

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • C++ 61.6%
  • C 38.4%