Trådfri Smart Plug #779
Comments
|
Controlling the plug through the |
|
I just bought the new Outlet and it seems that it doesn't work with the current version. Gateway shows only my motion sensor. Is it configuration that needs to be changed or code? |
|
Could you post deCONZ GUI screenshots of:
|
|
I am new to deconz, so I don't know if this is the right information:
|
|
The Cluster info panel reflects the last selected cluster. You need to click on the Basic cluster of the IKEA plug. Same for the Node info panel, you need to click on the IKEA plug - the above screenshot is for the RaspBee/ConBee. Looking at the node, it should be exposed as a It looks like the plug does support some measurement, through the Electrical Measurement cluster (0x0B04). Could you also post a screenshot of that cluster (again, after reading the attributes). We're interested in the |
|
The plug in the screenshots isn't the IKEA outlet isn't it? That's only a OSRAM plug?! |
|
No, I have a Osram plug and an Ikea. But the ikea one doesn‘t even show up. I think I tried the old and new web gui to search for devices, but nothing but the already connected devices were found. |
|
Does it have a reset button or something like that? Note: IKEA devices usually only try once to join the network.
|
|
No, I couldn't find one. The motion sensor has a button but not the plug, at least not on the surface. |
|
So the default app you have, gives me this screen: |
|
Looks like the plug is already assigned to another network, so it needs to be reset. You may try using the red reset button in the old webapp, the plug needs to be very close to the gateway. As alternative you can use a Hue dimmer switch to reset the plug, holding it very close to it and press buttons I and O for over 10 seconds. |
|
@maxlein, FACTORY RESET YOUR DEVICE For control outlet: use it to pair device. |
|
Thanks @zladukas, I threw the manual away and I could not find anything online! |
|
Cool, interesting, so it doesn't have power measurement but as a goody it seems to support ZigBee Green Power which is needed to route Hue tab and soon to be released ZGP switches. Is it shown in the Phoscon App under lights? |
|
And, apparently, a different manufacturer, looking at the mac address. (I should have done so earlier and recognised the first screenshot it was an OSRAM plug). There's apparently an inconsistency in general.xml: the generic (ZigBee 3.0) device 0x010a is an
Interesting... I think we still need deCONZ to configure the ZGP enabled routers or the ZGP devices will only work when in direct range of the RaspBee or ConBee, see #117. |
Not sure, maybe but we only know for sure after testing.
Absolutely, I sadly hadn't time yet to dig deeper in the ZGP spec, hopefully it's not too complicated to configure the ZGP proxies. |
|
Yes, it shows in the Phsoscon app. Its also working in openhab through hue binding and in homekit. (y) |
|
IKEA now has released the package including both the plug and the new on/off switch.
|
|
Is the smart plug and remote already working? I cant get them paired. If it should work, how should i pair them? |
From a previous comment. The remote isn't supported yet. See also Supported Devices |
|
Hm, i resetted it with the 5s method. Activated search for lights mode in deconz, but nothing shows up. |
|
Make sure the relay clicks (twice?) and the light on the device starts blinking. |
|
Often, at least in case of the IKEA bulbs, the device needs to be power cycled once after the reset in order to start joining. |
|
Well, I got the remote working. I just press the connect button a few times close to the antenna. |
@manup What's the issue with these switches, can I help with something to get them supported? |
|
Are you talking about the remote, or the switch for the plug? |
We are talking about the small switch sold with the plug… |
|
I bought 2 of these today hoping to pair them with Conbee/Deconz. No matter what order I try to reset the plugs, nothing happens in the logs of the Deconz Docker. Ive tried more or less everything in this thread, and others. What am I missing?:( Ive updated to the latest release of deconz and the latest firmware for Conbee. |
|
I've paired one yesterday, here is what I did:
It was then discovered quickly. |
How fast do you pull the plug on step 2? Straight after the "click"? |
After a few seconds. Do you have the ConBee connected directly to PC/RPi? If yes please try with an USB-extension cable. |
|
Its connected through an USB extension already. Tried doing the include further away from the server, but no success. The plug only blinks for 3-4 seconds before going solid white. No matter when I reinsert the plug, it always is solid white afterwards. |
|
@Cavemanz I had trouble resetting a couple of these. It turns out I just wasn't pressing hard enough. But if you're getting to the flashing then that doesn't seem like your issue. Have you tried holding a pin in for longer? The reset sequence is something like "click... flash a couple times... turn solid... fade out... flash again". You need to hold until you get to that second flashing phase, then deCONZ should find it. |
|
I do get the second flashing phase, but Deconz doesnt pick it up. I assume these logs from the docker aint related? 19:25:10:405 Search sensors done, |
|
The Beacons are a good sign that some device (the outlet?) tries to join. One thing you can check: do you have by any chance multiple Phoscon App tabs open, perhaps on multiple devices? If so please close all tabs but the one in which the light search is running. |
|
Sadly, I only had 1 window open on my main computer. Any other suggestions I could try? Getting a bit desperate. Id return the 2 I bought to IKEA but its a 1h drive so Id rather not if possible :) |
|
Hmm strange, by the way which deCONZ and ConBee firmware are you running? Latest is deCONZ 2.05.64 and firmware version 0x26330500. |
|
Version 2.05.63 / 3.4.2019 |
|
Yes release is online, might be worth a try. |
|
Anything in these logs that makes sense? Upgraded to newest version of Deconz and the firmware for Conbee. |
|
Log looks kinda ok, running out of ideas here. Maybe try to power-off the the other mains powered devices while joining the plug? This should force it to join directly via ConBee. |
|
Tried that now, no luck either. I dont get any Beacon log entries now either with my 4 lights switched off. I increased the search time to 3 min. It should show up as an actionable entry in the Lights section, right? |
|
Yes should look like this:
Do you have access to the deCONZ GUI via VNC? Only remaining thing to check are the Zigbee network parameters in the GUI. |
|
Into the Docker container you mean? I havent tried that before. |
|
That's the Phoscon App, showing only a limited set of the parameters. The full Zigbee configuration is only visible in deCONZ GUI, with marthocs docker container it can be accessed via VNC (unfortunately I haven't done this myself yet) . Configuration looks like
|
|
Managed to enable it in my docker compose file: |
|
Hmm, these look fine too, all parameters are valid. |
|
I powered on my 4 lights again. Tried pairing both of my plugs. The Beacon src messages are back now, but nothing happens :/ |
|
The beacons come from the lights, they are responses to the plug which requests them in order to find suitable routers to join. |
|
Ok, Im close to giving up on these. Annoying that they wont pair seeing how Philips/Osram/Xiaomi pairs without issue :/ |
|
A lot of times in this thread a hole in the bottom of the plug is mentioned. Mine doesn't have one. How can I add it in deconz? |
|
@r41d if yours really doesn't have a hole in the bottom then you should return it because it's defective. But make sure you're looking in the right place. I would describe it as the "outside" more than the bottom, it's on the curved part of the plastic, on the side between the male part of the plug and the female part of the plug. It's pretty small, about the size of a pin, but it's possible the plastic didn't get punched/molded properly and the hole is filled in. |
|
After taking pictures to show that I see no hole and uploading them I took another look and finally spotted the tiny hole at the bottom ^^. It's funny that you don't need it to for regular pairing with the official Gateway but that it's necessary for pairing with ConBee. |
|
It was really hard to pair mine. I tried multiple times to pair the socket, but failed many times. Does anybody own the IKEA gateway an know if pairing is also such a PITA there? |
|
The IKEA hub works very differently: it only supports touchlink pairing. You need to touchlink-pair a controller to the hub, and then touchlink-pair the controller to the light, plug, repeater, or window blind. Note that the Trådfri motion sensors act as controllers. |
|
I know this is closed, but curious if it got resolved? Could it be the Zigbee channel being 11? |
Hi,
Do you think the new Trådfri smart plug will work with deconz right away when it is released? Or does support have to be added?
https://www.ikea.com/se/sv/catalog/products/90356166/
Maybe hard to know before it has been released? :)
The text was updated successfully, but these errors were encountered: