-
Notifications
You must be signed in to change notification settings - Fork 69
/
__user_project_wrapper.v
167 lines (146 loc) · 4.95 KB
/
__user_project_wrapper.v
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
`default_nettype none
/*
*-------------------------------------------------------------
*
* user_project_wrapper
*
* This wrapper enumerates all of the pins available to the
* user for the user project.
*
* An example user project is provided in this wrapper. The
* example should be removed and replaced with the actual
* user project.
*
*-------------------------------------------------------------
*/
module user_project_wrapper #(
parameter BITS = 32
)(
`ifdef USE_POWER_PINS
inout vdda1, // User area 1 3.3V supply
inout vdda2, // User area 2 3.3V supply
inout vssa1, // User area 1 analog ground
inout vssa2, // User area 2 analog ground
inout vccd1, // User area 1 1.8V supply
inout vccd2, // User area 2 1.8v supply
inout vssd1, // User area 1 digital ground
inout vssd2, // User area 2 digital ground
`endif
// Wishbone Slave ports (WB MI A)
input wb_clk_i,
input wb_rst_i,
input wbs_stb_i,
input wbs_cyc_i,
input wbs_we_i,
input [3:0] wbs_sel_i,
input [31:0] wbs_dat_i,
input [31:0] wbs_adr_i,
output wbs_ack_o,
output [31:0] wbs_dat_o,
// Logic Analyzer Signals
input [127:0] la_data_in,
output [127:0] la_data_out,
input [127:0] la_oenb,
// IOs
input [`MPRJ_IO_PADS-1:0] io_in,
output [`MPRJ_IO_PADS-1:0] io_out,
output [`MPRJ_IO_PADS-1:0] io_oeb,
// Analog (direct connection to GPIO pad---use with caution)
// Note that analog I/O is not available on the 7 lowest-numbered
// GPIO pads, and so the analog_io indexing is offset from the
// GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
inout [`MPRJ_IO_PADS-10:0] analog_io,
// Independent clock (on independent integer divider)
input user_clock2,
// User maskable interrupt signals
output [2:0] user_irq
);
// Dummy assignments so that we can take it through the openlane flow
`ifndef GPIO_TESTING
`ifdef SIM
// Needed for running GL simulation
assign io_out = 0;
assign io_oeb = 0;
`else
assign io_out = io_in;
`endif
`endif // GPIO_TESTING
`ifdef LA_TESTING
user_project_la_example la_testing(la_data_in,la_data_out,la_oenb);
`endif
// splitting the address space to user address space and debug address space
// debug address space are the last 2 registers of user_project_wrapper address space
wire wbs_cyc_i_user;
wire wbs_ack_o_user;
wire [31:0] wbs_dat_o_user;
wire wbs_cyc_i_debug;
wire wbs_ack_o_debug;
`ifdef GPIO_TESTING
wire wbs_ack_o_gpio;
wire [31:0] wbs_dat_o_gpio;
`endif
wire [31:0] wbs_dat_o_debug;
// reserve the last 2 regs for debugging registers
// `ifndef GPIO_TESTING
assign wbs_cyc_i_user = (wbs_adr_i[31:3] != 29'h601FFFF) ? wbs_cyc_i : 0;
assign wbs_cyc_i_debug = (wbs_adr_i[31:3] == 29'h601FFFF) ? wbs_cyc_i : 0;
// `endif
// `ifndef GPIO_TESTING
assign wbs_ack_o = (wbs_adr_i[31:3] == 28'h601FFFF) ? wbs_ack_o_debug : wbs_ack_o_user;
assign wbs_dat_o = (wbs_adr_i[31:3] == 28'h601FFFF) ? wbs_dat_o_debug : wbs_dat_o_user;
// `endif
`ifndef GPIO_TESTING
assign wbs_ack_o_user = 0;
`endif
// // reserve the last 4 regs for debugging registers in case of user gpio testing
// `ifdef GPIO_TESTING
// assign wbs_cyc_i_user = (wbs_adr_i[31:4] != 28'h300FFFF) ? wbs_cyc_i : 0;
// assign wbs_cyc_i_debug = (wbs_adr_i[31:4] == 28'h300FFFF) ? wbs_cyc_i : 0;
// `endif
// `ifdef GPIO_TESTING
// assign wbs_ack_o = (wbs_adr_i[31:4] == 28'h300FFFF) ? (wbs_adr_i[3:0]>=4'h8) ? wbs_ack_o_debug : wbs_ack_o_gpio : wbs_ack_o_debug;
// assign wbs_dat_o = (wbs_adr_i[31:4] == 28'h300FFFF) ? (wbs_adr_i[3:0]>=4'h8) ? wbs_dat_o_debug : wbs_dat_o_gpio : wbs_dat_o_user;
// `endif
`ifdef GPIO_TESTING
user_project_gpio_example gpio_testing(
.wb_clk_i(wb_clk_i),
.wb_rst_i(wb_rst_i),
.wbs_cyc_i(wbs_cyc_i_user),
.wbs_stb_i(wbs_stb_i),
.wbs_we_i(wbs_we_i),
.wbs_sel_i(wbs_sel_i),
.wbs_adr_i(wbs_adr_i),
.wbs_dat_i(wbs_dat_i),
.wbs_ack_o(wbs_ack_o_user),
.wbs_dat_o(wbs_dat_o_user),
.io_in(io_in),
.io_out(io_out),
.io_oeb(io_oeb));
`endif
debug_regs debug(
.wb_clk_i(wb_clk_i),
.wb_rst_i(wb_rst_i),
.wbs_cyc_i(wbs_cyc_i_debug),
.wbs_stb_i(wbs_stb_i),
.wbs_we_i(wbs_we_i),
.wbs_sel_i(wbs_sel_i),
.wbs_adr_i(wbs_adr_i),
.wbs_dat_i(wbs_dat_i),
.wbs_ack_o(wbs_ack_o_debug),
.wbs_dat_o(wbs_dat_o_debug)
);
endmodule // user_project_wrapper