net: dsa: mt7530: setup core clock even in TRGMII mode

A recent change to MIPS ralink reset logic made it so mt7530 actually
resets the switch on platforms such as mt7621 (where bit 2 is the reset
line for the switch). That exposed an issue where the switch would not
function properly in TRGMII mode after a reset.

Reconfigure core clock in TRGMII mode to fix the issue.

Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled.

Fixes: 3f9ef77 ("MIPS: ralink: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/mt7530.c

@@ -436,34 +436,32 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
 			     TD_DM_DRVP(8) | TD_DM_DRVN(8));
 
 	/* Setup core clock for MT7530 */
-	if (!trgint) {
-		/* Disable MT7530 core clock */
-		core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
-
-		/* Disable PLL, since phy_device has not yet been created
-		 * provided for phy_[read,write]_mmd_indirect is called, we
-		 * provide our own core_write_mmd_indirect to complete this
-		 * function.
-		 */
-		core_write_mmd_indirect(priv,
-					CORE_GSWPLL_GRP1,
-					MDIO_MMD_VEND2,
-					0);
-
-		/* Set core clock into 500Mhz */
-		core_write(priv, CORE_GSWPLL_GRP2,
-			   RG_GSWPLL_POSDIV_500M(1) |
-			   RG_GSWPLL_FBKDIV_500M(25));
+	/* Disable MT7530 core clock */
+	core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
 
-		/* Enable PLL */
-		core_write(priv, CORE_GSWPLL_GRP1,
-			   RG_GSWPLL_EN_PRE |
-			   RG_GSWPLL_POSDIV_200M(2) |
-			   RG_GSWPLL_FBKDIV_200M(32));
-
-		/* Enable MT7530 core clock */
-		core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
-	}
+	/* Disable PLL, since phy_device has not yet been created
+	 * provided for phy_[read,write]_mmd_indirect is called, we
+	 * provide our own core_write_mmd_indirect to complete this
+	 * function.
+	 */
+	core_write_mmd_indirect(priv,
+				CORE_GSWPLL_GRP1,
+				MDIO_MMD_VEND2,
+				0);
+
+	/* Set core clock into 500Mhz */
+	core_write(priv, CORE_GSWPLL_GRP2,
+		   RG_GSWPLL_POSDIV_500M(1) |
+		   RG_GSWPLL_FBKDIV_500M(25));
+
+	/* Enable PLL */
+	core_write(priv, CORE_GSWPLL_GRP1,
+		   RG_GSWPLL_EN_PRE |
+		   RG_GSWPLL_POSDIV_200M(2) |
+		   RG_GSWPLL_FBKDIV_200M(32));
+
+	/* Enable MT7530 core clock */
+	core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
 
 	/* Setup the MT7530 TRGMII Tx Clock */
 	core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);