ATTENTION: To run this on the m5stickc plus 2, in addition to main code changes in this fork, a fix for the changed TFT_eSPI LCD pin out is required in /.pio/libdeps/m5stick-c/M5StickCPlus/src/utility/In_eSPI_Setup.h after the M5StickCPlus library is installed.
... /* existing definitions from plus #define TFT_MOSI 15 #define TFT_SCLK 13 #define TFT_CS 5 // Chip select line for TFT display on Shield #define TFT_DC 23 // Data/command line for TFT on Shield #define TFT_RST 18 // Reset line for TFT is handled by seesaw! */
// plus and plus2 #define TFT_MOSI 15 #define TFT_SCLK 13 #define TFT_CS 5 // Chip select line for TFT display on Shield
// plus2 #define TFT_DC 14 // Data/command line for TFT on Shield #define TFT_RST 12 // Reset line for TFT is handled by seesaw! #define TFT_BL 27 // LED back-light (required for M5Stack) #define TFT_BACKLIGHT_ON HIGH // Level to turn ON back-light (HIGH or LOW) ...
Blackmagic Design camera control on a LILYGO T-Display-S3, M5Stack M5CoreS3, M5Stack M5StickC Plus, Freenove ESP32-S3-WROOM, or (hopefully) any other ESP32 device.
Designed for the Pocket 4K, Pocket 6K/G2/Pro, USRA G2 4.6K, URSA 12K.
Coding is in C++ and setup for development in Visual Studio Code with the PlatformIO extension.
NOTE: If you're using Mac or Linux and recently cloned the repository and were not able to get it running then please try again as all backslashes in the #includes have been changed to forward slashes.
Video with demos (opens YouTube):
⭐ How about a Star?
The key features are:
- Connect to the cameras wirelessly over Bluetooth LE
- Detect multiple cameras to allow you to select the camera to connect to, if multiple are available
- Entry of the Bluetooth connection code (6 digit pin) through a touchscreen numpad (LILYGO T-Display-S3, M5Stack CoreS3)
- Entry of the Bluetooth connection code (6 digit pin) through the serial console (when you don't have touch-screen or keypad)
- Multiple screens that can be viewed by swiping left and right (LILYGO T-Display-S3, M5Stack CoreS3)
- Screens and functionality (LILYGO T-Display-S3, M5Stack CoreS3)
- Dashboard: View the ISO, Shutter Speed, White Balance/Tint, Codec, FPS, active media device, and resolution
- Recording: Start and Stop recording, shows timecode and the remaining time left on the active media
- ISO: Change ISO
- Read and write the many settings of the camera (Record Start & Stop, ISO, Shutter Speed / Angle, White Balance, Tint, Codec, Resolution, FPS, Off-speed Recording, Media available and time remaining, Slate, Project Name, Lens Data)
- Accept setting changes through serial text (e.g. "(ISO:4000)" sent over serial will update the ISO to 4000). Similarly, it can output settings through serial so your applications can synchronise settings with the camera(s)
December 2023
Added lens focusing on the M5Stack CoreS3 using the M5Stack rotary encoder. Initial testing on Pocket 6K and URSA Mini Pro G2.
Two modes:
- Free Focus - turn the rotary encoder and it will change focus position freely
- Range - turn the rotary encoder and it behaves more like a follow-focus with hard stops
Why two modes? The BMD EF-based cameras have variations in the lenses supported and how to control them. The free-focus uses an offset for each step on the rotary encoder - this works on the URSA Mini Pro G2. The Range sends specific positions to the camera - this didn't work on the URSA Mini Pro G2 but did on the Pocket 6K (where both options worked). Additionally, for the free-focus offset different values moved the lens focus position different amounts depending on the lens.
Therefore, you'll likely need to play around to see if this works for you!
--
Added support for the URSA Mini Pro G2 for general features - see the M5Stack CoreS3 main file.
Thanks to Paul Jones for lending me his camera!
I hope you find the functionality useful and it would be great if you could contribute your improvements, suggestions, or general feedback to the project!
If you're a TouchDesigner user, check out nelsoniso's repository here which utilises the serial output of this project to update TouchDesigner in real-time and allow you to control the settings of the camera from TouchDesigner, it's very cool.
The main-m5stack-grey-touchdesigner.cpp file has the serial in and out functionality.
It needs to be thoroughly tested and even though they do contain fairly basic functionality, there's still unknowns around connection longevity, camera firmware changes, known issues in camera firmware, and the position of the sun in the sky.
Here's the state of cameras and firmware.
| Camera | Firmware | Status |
|---|---|---|
| Pocket 4K | 7.9.1 |
|
| Pocket 4K | 8.1 |
|
| Pocket 6K | 7.9.1 |
|
| Pocket 6K | 8.1 |
|
| Pocket 6K G2 | ... | PeterP27 confirmed |
| Pocket 6K Pro | ... | Not Tested |
| URSA Mini Pro 4.6K G2 | ... |
|
| URSA Mini Pro 12K | ... | Not Tested |
| URSA Mini Pro 12K OLPF | ... | Not Tested |
If you're in Sydney, Australia, and would be able to lend me a camera I haven't tested for a day to test so we know it works, that would be amazing.
- Changing Codecs between BRAW and ProRes on Camera Firmware 7.9.1 on Pocket cameras not functioning
- Changing Codecs between BRAW and ProRes on Camera Firmware 8.1 on Pocket 4K not switching until you've manually changed them once on the camera
- Changing Codecs between BRAW and ProRes on Camera Firmware 8.1 on Pocket 6K not switching (even if you manually change them beforehand)
- Changing resolutions when using ProRes on Camera Firmware 8.1 on Pocket cameras not functioning in all cases (ProRes 4K DCI to UHD or HD, may require you to manually change them once on the camera)
My primary objective was to convert a Windows-based application I had for controlling my cameras to a small portable device.
These devices are so small, portable, and don't require much power.
I'm opening up to the community who may find this useful or would like to contribute to it. Any contribution you make will be appreciated!
I found this device had all the necessary components needed to connect and interact with the cameras:
- Connect over Bluetooth LE
- Touchscreen to enter the connection code (which is a challenge with screen-less touch-less devices)
- Touchscreen to support gestures (swiping left and right to change screens)
- Nice bright and colourful 320 x 170 display
- Powered over USB-C or a battery
- Cheap! ~$22USD (or $40AUD for us Aussies)
Hopefully all of them are supported and I have a few that I'm developing for to check they work - LILYGO T-Display-S3, M5Stack M5CoreS3, M5Stack M5StickC Plus, Freenove ESP32-S3-WROOM.
It would be great if you could let the community know what ESP32 device you have and whether it works and I'll update this note.
Yes, indeed you can! Alternatively, this is designed as a lightweight small device that allows you to see and control basic functions of your camera. It can act as a dedicated device for each camera you have, or simply to avoid touching the camera to control it (when it's on a gimbal, mounted somewhere, or in a moving car :) ).
You will need the following:
- An ESP32 device
- If you want the touch-screen functionality try the LILYGO T-Display-S3 Touch version Buy here, ~$22USD
- Make sure to get the Touch version!
- You can also try the M5Stack M5CoreS3 which comes with an in-built battery Buy here, ~60USD
- If you want the touch-screen functionality try the LILYGO T-Display-S3 Touch version Buy here, ~$22USD
- Visual Studio Code (VS Code) Free, download here
- The PlatformIO extension within VS Code (see below on how to configure PlatformIO for this device)
- A Blackmagic Design camera (Pocket 4K/6K/6K G2/6K Pro, URSA 4.6K G2, URSA 12K)
It is important that you use PlatformIO if you want to use the repository as it is. Feel free to use the libraries in your own project if you don't want to develop for the repository. The following notes are based on using this repository
platformio.ini - This file tells PlatformIO what boards you have and which "main-[board name].cpp" file to use. In the src/main/ folder you'll see a set of main cpp files, each one is the program that relates to the board. When you compile and upload the program to your board PlatformIO uses the main file that matches the name of the board you have chosen (in the bottom taskbar of Visual Studio Code you can choose the environment you are using which represents the board. For example, programming for the M5Stack M5StickC Plus will be done in the src/main/main-m5stick-c.cpp file because that has the name related to the environment chosen when we select "env:m5stick-c".
If you want to add your own board and program for it, do so like this:
- Open platformio.ini and check if the board already exists, if so you're good to go.
- If not, go to the PlatformIO boards page and find your board. If you don't find it you'll need to find something as close as possible.
- Click on the board name and it will open up its own page
- Look for the ID of the board. For example, for the Adafruit ItsyBitsy ESP32 the ID is adafruit_itsybitsy_esp32.
- Add the following to the end of the platformio.ini file (putting in the ID of the board):
[env:adafruit_itsybitsy_esp32]
platform = espressif32
board = adafruit_itsybitsy_esp32
- Save the file
- Create a main source file under src/main/ that has the ID of the board prefixed by "main-", e.g. "src/main/main-adafruit_itsybitsy_esp32.cpp"
- Choose the new environment using the bottom environment bottom of Visual Studio Code
- Click Build to compile (make sure your main file has at least "void setup()" and "void loop()" defined)
You will need to do the following to ensure that the TFT_eSPI library is configured for the LilyGO T-Display-S3 or any other device that you're using it for:
- The platformio.ini file within the project should already have TFT_eSPI as a library dependency. If you don't see TFT_eSPI under your ".pio\libdeps" folder > under the PlatformIO home page within Visual Studio Code, click on Libraries, search for TFT_eSPI. Click on it and then click on Add to Project, select your project and click Add. Proceed to the next point.
- Ensure you have uncommented the device line in the User_Setup_Select.h file (pio\build\libdeps<device ID>\User_Setup_Select.h) for TFT_eSPI and also commented out the default line (around line 30). For example the T-Display-S3 line is around line 133 of the file.
- Similarly, if you don't have the "Arduino_DebugUtils" under your ".pio\libdeps" folder, add the "Arduino_DebugUtils" library to the project using the same method above.
See the Blackmagic Camera Control Developer Information document, here. It's not up-to-date and I've used the sample code, noted below, to update functionality. There remains other functionality not documented or in the code samples that has been worked out by the community.
I converted a lot of the Swift (Mac) code from Blackmagic Design's Cameras Code Samples, Download here
- Blackmagic Design: For making affordable cameras and having a public protocol so we can interact with them
- Blackmagic Design Support: A big shoutout to Brendan at Blackmagic Design who helped troubleshoot the changing of Codecs, which was/is a known bug in the camera firmware. Thanks Brendan!
- BlueMagic32: A great project to control cameras with an ESP32. It provided a reference for the Bluetooth connection functionality. https://github.com/schoolpost/BlueMagic32
- LILYGO: For creating a cool product and having some code examples for it. https://github.com/Xinyuan-LilyGO/T-Display-S3
- Volos Projects on YouTube: For having an entertaining set of videos on programming for the T-Display-S3. T-Display-S3 Touch example
- ChatGPT: The ability to convert code from Swift to C++ and to assist with C++ coding has saved days of programming. https://chat.openai.com/
- I'm not seeing anything on the screen?
- Ensure you have uncommented the T-Display-S3 line (Around line 133) in the User_Setup_Select.h file for TFT_eSPI and also commented out the default line (Around line 30). In PlatformIO this is under libdeps\lilygo-t-display-s3\TFT_eSPI\TFT_eSPI.h
- It's not working on my camera?
- Ensure that you have Bluetooth turned on in the Setup menu on the camera
- I have tested with the Pocket 4K and 6K (Original) - contact me if you are having trouble connecting to your camera.
- The version of your firmware may need to be updated to the latest version so the protocol used is compatible with your camera.
- How do I enter the PIN code to connect?
- If you're using the LILYGO T-Display-S3 touch-version there's an on-screen numpad that appears when you're required to enter the code.
- If you're using another ESP32, such as one without a screen, you can use the Serial console to enter the PIN code (see the M5Stick example code) for the first time you connect. Once you've done that you can unplug the device from your computer.
- Once you've entered the code and connected succesfully both devices should remember each other for future connections, unless you clear the connections (as can be done on the Camera under the Bluetooth screen).
See the programming and device tips document, DevelopmentTips.md.
- The use of this software is at your own risk. The creator of this software cannot be held liable.
- Using this software therefore is completely at your own risk.
- GPL-3.0 license
- Converted Swift code from the Blackmagic Design Cameras Code Samples Download here
You can contact me here
Thanks for being part of the community! ✨