Display NHL score of your favorite team's game on a Raspberry Pi driven RGB LED matrix. Currently supports 64x32 boards only.
This project was inspired by the mlb-led-scoreboard. Go check it out and try it on your board, even if you are not a baseball fan, it's amazing. I also used this nhlscoreboard repo as a guide at the very beginning as I was learning python.
Display the live score in near real time (refresh every minute) of a select game (set in the config file). If one of the team score a goal, a goal animation (.gif) is played.
If your team has a game scheduled, The screen will display a preview screen of the game.
Display a message to announce the sad news.
Syncing the scoreboard with a TV Broadcast is, to my knowledge, impossible. The delay between the actual game and the TV broadcast is different depending on where you are in relation to the game's location. I use the NHL API which will refresh and show scores before the TV broadcast. That means that most of the time, the scoreboard will show the goal before you see it happen on the TV.
During a live game, the stats will refresh every minute. This is because generally, the API refresh at the same rate. Also, the API update to the new day at 4 PM UTC (At noon EST time). The scoreboard will fallow that update in the hour following this.
If you see the scoreboard doesn't show the right state or stats, just quit and re-run it.
While writing this README page, I realized that the mlb-led-scoreboard guys made a great wiki page to cover the hardware part of the project. See the mlb-led-scoreboard wiki page.
Before you start installing anything, make sure your raspberry pi is set to your local time zone. Usually, you do so when you install Raspian, but if you think you skipped that part, you can change it by running sudo raspi-config
You need Git for cloning this repo and PIP for installing the scoreboard software.
sudo apt-get update
sudo apt-get install git python-pip
This installation process might take some time because it will install all the dependencies listed below.
git clone --recursive https://github.com/riffnshred/nhl-led-scoreboard
cd nhl-led-scoreboard/
sudo ./install.sh
rpi-rgb-led-matrix : The open-source library that allows the Raspberry Pi to render on the LED matrix.
pytz, tzlocal: Timezone libraries. These allow the scoreboard to convert times to your local timezone.
requests: To call the API and manipulate the received data.
If you have been using a Led matrix on a raspberry pi before and know how to run it properly skip this part.
If you just bought your Led matrix and want to run this software right away, first thank you. Second, don't get to excited just yet.
Go on the rpi-rgb-led-matrix , install it on your raspberry. Check out the section that uses the python bindings and run some of their examples on your screen. For sure you will face some issues at first, but don't worry, more than likely there's a solution you can find in their troubleshooting section. Once you found out how to make it run smoothly, come back here and do what's next.
If you are using any thing from raspberry pi 3+ to the newest versions with an Adafruit HAT or Bonnet, here's what I did to run my board properly.
- Do the hardware mod found in the Improving flicker section .
- Disable the on-board sound. You can find how to do it from the Troubleshooting sections
- From the same section, run the command that remove the bluetooth firmware, Unless you use any bluetooth device with your Pi.
Finally, here's the command I use.
sudo python main.py --led-gpio-mapping=adafruit-hat-pwm --led-brightness=60 --led-slowdown-gpio=2
First thing first, find your fav team's id number.
| Team | ID | Team | ID | |
|---|---|---|---|---|
| Anaheim Ducks | 24 | Nashville Predators | 18 | |
| Arizona Coyotes | 53 | New Jersey Devils | 1 | |
| Boston Bruins | 6 | New York Islanders | 2 | |
| Buffalo Sabres | 7 | New York Rangers | 3 | |
| Calgary Flames | 20 | Ottawa Senators | 9 | |
| Carolina Hurricanes | 12 | Philadelphia Flyers | 4 | |
| Chicago Blackhawks | 16 | Pittsburgh Penguins | 5 | |
| Colorado Avalanche | 21 | San Jose Sharks | 28 | |
| Columbus Blue Jackets | 29 | St Louis Blues | 19 | |
| Dallas Stars | 25 | Tampa Bay Lightning | 14 | |
| Detroit Red Wings | 17 | Toronto Maple Leafs | 10 | |
| Edmonton Oilers | 22 | Vancouver Canucks | 23 | |
| Florida Panthers | 13 | Vegas Golden Knights | 54 | |
| Los Angeles Kings | 26 | Washington Capitals | 15 | |
| Minnesota Wild | 30 | Winnipeg Jets | 52 | |
| Montreal Canadiens | 8 |
Open the config.json file from the root folder and change the "fav_team_id" to your favorite team's id. This will make the scoreboard to fallow
your team by default. Otherwise... GO HABS GO !!!!
Now, in a terminal, cd to the nhl-led-scoreboard folder and run this command.
sudo python main.py
If you run your screen on an Adafruit HAT or Bonnet, you need to supply a flag.
sudo python main.py --led-gpio-mapping=adafruit-hat
Use the same flags used in the rpi-rgb-led-matrix library to configure your screen.
--led-rows Display rows. 16 for 16x32, 32 for 32x32. (Default: 32)
--led-cols Panel columns. Typically 32 or 64. (Default: 32)
--led-chain Daisy-chained boards. (Default: 1)
--led-parallel For Plus-models or RPi2: parallel chains. 1..3. (Default: 1)
--led-pwm-bits Bits used for PWM. Range 1..11. (Default: 11)
--led-brightness Sets brightness level. Range: 1..100. (Default: 100)
--led-gpio-mapping Hardware Mapping: regular, adafruit-hat, adafruit-hat-pwm
--led-scan-mode Progressive or interlaced scan. 0 = Progressive, 1 = Interlaced. (Default: 1)
--led-pwm-lsb-nanosecond Base time-unit for the on-time in the lowest significant bit in nanoseconds. (Default: 130)
--led-show-refresh Shows the current refresh rate of the LED panel.
--led-slowdown-gpio Slow down writing to GPIO. Range: 0..4. (Default: 1)
--led-no-hardware-pulse Don't use hardware pin-pulse generation.
--led-rgb-sequence Switch if your matrix has led colors swapped. (Default: RGB)
--led-pixel-mapper Apply pixel mappers. e.g Rotate:90, U-mapper
--led-row-addr-type 0 = default; 1 = AB-addressed panels. (Default: 0)
--led-multiplexing Multiplexing type: 0 = direct; 1 = strip; 2 = checker; 3 = spiral; 4 = Z-strip; 5 = ZnMirrorZStripe; 6 = coreman; 7 = Kaler2Scan; 8 = ZStripeUneven. (Default: 0)
I also created a flag to change which team to fallow instead of the default team.
--fav-team Select a team to follow by using it's ID (Default: 8 "Montreal Canadiens")
I will soon release the full set of features that I want to add to this project. I'm talking about standings, showing the score of the other games, showing future scheduled games, playoff related features and more. Just like the MLB led scoreboard project, I see a lot of potentials. If you want to help, or have an idea, open an issue and send the details.
This project use the GNU Public License. If you intend to sell these, the code must remain open source.