1.5.4

New Features:

• Update Codebase to Marlin 2.1.2.2 (Thanks @stklcode !)

Bugfixes:

• Fix ignored z endstop when only one endstop is used (thanks @hostops !)
• Fix continue button behavior after pause or filament runout (thanks @uwetaz !)
• Fix 'lack of filament' message not displayed when filament runs out (thanks @uwetaz !)
• Fix homing issue when using two endstops (thanks @stklcode !)

❤️ I would like to once again thank everyone involved! You are great! ❤️

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

*You may not have to reset everything.
However, the prerequisites for this are difficult to tell, which is why I wrote something this topic here in english and here in german.

1.5.3

New Features:

• None. This is just a bugfix release

Bugfixes:

• Fix build issues when compiling with newer Python versions
• Fix Thermal Runaway, which was too aggressive in some cases
• Fix Filament Runout, which which resulted in false positives in the past
• Fix manual bed leveling on Mega Pro

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

*You may not have to reset everything.
However, the prerequisites for this are difficult to tell, which is why I wrote something this topic here in english and here in german.

1.5.2

New Features:

• Add Marlin M73 Support to get a more accurate print time display
• Improve overall stability (Thanks @stklcode !)

Bugfixes:

• Heater error check on boot did not trigger at all

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

*You may not have to reset everything.
However, the prerequisites for this are difficult to tell, which is why I wrote something this topic here in english and here in german.

1.5.1

*This version was hotfixed on 2023-06-13.

New Features:

• Update Codebase to Marlin 2.1.2.1 (Thanks @stklcode !)
• Faster file list load/refresh
• Support for SD Card extenders

Bugfixes:

• In some cases, printers with Anycubic 1.0 Displays had issues reading the SD card or crashed at startup
• When scrolling many times though the file list, the Output got scrambled on DGUS Clone Screens
• Sometimes after long prints the elapsed time showed --.--
• When no filament sensor is connected, there was a boot loop on printers with Anycubic 1.0 Displays

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.5.0

New Features:

• Update Codebase to Marlin 2.1.2 (Thanks @stklcode !)
• Low noise SoftPWM is now used for Fans and Heaters
• Touchscreen code as fully functional ExtUI module
• Print/Pause/Resume/Stop works as intended
• M600 filament change with or without USB connection
• Host action commands for most of the touchscreen functions
• Filament Sensor works internally and externally via USB
• Filament Sensor can be enabled/disabled permanently via special menu
• When a print is stopped manually, the bed moves forward and the printhead into parking position
• Live-Z-Offset on Anycubic Chiron Models
• Automatic Mesh adjustment when altering Z-Offset on Chiron
• Support for .gco files on all Displays
• Alphabetic file and folder sorting on all Displays
• When using ABL or MBL, the nozzle now can go below endstop zero
• HighSpeed Mode for BLTouch probing (selectable via Special Menu)

Bugfixes:

• Fix compile error when using NeoPixels
• Fix use of rectangular shape beds
• Fix Z home position not touching the buildplate
• Fix default baudrate and port number for ESP wifi module
• Fix some files not displayed on older Touchscreens
• Fix corrupted file parsing code
• Fix BLTouch probing or BLTouch error when using clone probes
• Fix Filament Sensor on Chiron and 4MAX Pro 2.0
• Fix a bug, when navigating in a directory, you could not go back
• Fix Anycubic 1.0 Display, directories could not be accessed
• Fix 4MAX Pro 2.0 M600 takes too much time on Filament Change
• Fix missing Z2 pin definitions on Chiron and 4MAX
• Fix Chiron ABL which was broken since 1.5.0 Beta
• Fix Special Menu is not displayed when no SD card is inserted
• Fix Load FW defaults routine
• Fix Chiron live offset not rendered correctly
• Fix 4MAX Pro Auto PowerOff

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.4

Features:

• M851 and Babystepping is combined, so Babystepping can be used to alter the current Z Offset while printing.
• Enable M808 gcode for repeat markers (thanks @stklcode )
• The correct Marlin Version is now shown instead of just "2.0.x".

Bugfixes:

• 4MAX Pro now correctly resets after boot.
• Fix build error because the TMC26XX Library was removed.
• Fix Pause via USB print, which is not automatically resumed now.
• Fix missing software endstop on Z_MIN.

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
• If the print is paused, it can not be resumed via the Display UI. Please print via USB/Octoprint instead!

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.3

Features:

• Nothing new. This is just a bugfix release.

Bugfixes:

• When using 4-point-easy-leveling, the Mesh was applied wrongly and falsified the result. See #282

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.2

Features:

• Integrated assisted Leveling for MEGA Pro.
• Motors and Heaters are stopped right after aborting a print.

Bugfixes:

• Fix an issue, where in some cases a print could not be aborted while heating.

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.1

Features:

• Same new Features like in Version 1.4.0 but with HardwarePWM and higher PWM frequency.

Bugfixes:

• Some users reported clicking/ticking noise coming from the PSU when the Hotbed reached the desired Temperature. This version uses the same PWM controller like the last generation (1.3.1 and below) to ensure a perfect compatibility.

Known Issues:

• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
• On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.0

Warning!
Some users reported a clicking/ticking noise coming from the power supply. The heating behavior of the bed has also deteriorated. I strongly recommend using bugfix version 1.4.1 or newer!

Features:

• Update code base to Marlin 2.0.9.2 including all new Marlin features.
• Mega Pro Laser support with M3 - Spindle CW / Laser On functionality.
• Laser Support for Tools like LightBurn.
• Support for Anycubic 4MAX Pro v1 and v2.*
• Support for 4MAX Pro 2.0 with original DWIN II Display.
• 4MAX Pro Auto-Power-Off.
• More reliable acceleration and jerk values on all printers.
• Overall higher possible extruder speeds.
• Enabled Host Actions Commands to control the firmware via USB.
• Add M9999 Anycubic TFT Debug command. (Thanks to @etet100)
• Switched Thermistor Type from 5 to 1 or 11 (depending on your printer).
• Allow longer Filenames on DGUS Clone/Anycubic 0.0.2 Display.
• Lower fan noise when using low fan speeds.

Special Thanks to Stefan Kalscheuer known as @stklcode for his great work merging the marlin upstream sources!

*4MAX Pro and 4MAX Pro v2 share the same firmware. Please use the 4MAXP2 binary suitable for your Display (Original DWIN II or Anycubic 0.0.2)

Bugfixes:

• 4MAX Pro 4 Point Easy Leveling now works as expected.
• 4MAX Pro PID Tune Hotend feature fixed.
• Chiron TFT crashed after auto leveling.
• Chiron Z Offset was not stored in EEPROM.
• Add missing Touchscreen Implementation for M104.
• Add missing Touchscreen Implementation for M109.
• Increased probe margin to avoid probing outside of bed boundaries.
• Default level fade height is 0 to disable it to avoid breaking layers.
• Fix resume from pause with M108 command.
• Fix humming noise on MEGA X when moving Z axis.
• Fix advanced pause feature when using Touchscreen.
• Fix re-heat nozzle feature after timeout (when using pause/m600 or filament runout)
• Fix advanced resume feature to continue a print after an error.
• Fix/Workaround for DWIN/DGUS II Pause/Resume.
• Fix missing home/G28 when starting manual mesh bed leveling.
• Fix noise on stock Mega Pro X and Y drivers by switching zu A4988 timings.
• Fix lockup/freeze when pressing STOP on Anycubic 0.0.2 Display.

Known Issues:

• Some users reported clicking/ticking noises coming from the power supply. In that case, please switch back to HardwarePWM by commenting out ( // ) #define FAN_SOFT_PWM.
• The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
• The Mega Pro BMP Laser feature is not supported. Use the M3 Spindle/Laser feature instead.
• On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
• The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
• The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.

How to Install:

1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!