Does this project support FYSETC SD-WIFI-PRO? #954

y2kdread · 2023-10-10T21:53:44Z

y2kdread
Oct 10, 2023

Hi -

I have very little experience with ES32 based programming, but was wondering if this project is compatible with the Fysetc SD-WIFI-PRO?

The chipset on that SD card is ESP32 Pico-D4, I would like to be able to use WebDAV on that card but it doesn't have support from Fysetc at this time. If it is supported, does anyone have resources on how I can compile the image to be used with the card?

Thanks!

luc-github · 2023-10-10T23:08:29Z

luc-github
Oct 10, 2023
Maintainer

Yes esp3d V3 is compatible with Fysetc SD-WIFI-PRO, and yes WebDav is working on it
You have to follow the specs of the board on https://luc-github.github.io/#/config/features and use the results on esp3d V3

0 replies

y2kdread · 2023-10-10T23:38:45Z

y2kdread
Oct 10, 2023
Author

Awesome! I'll give this a try.

…

On Tue, Oct 10, 2023, 6:08 PM Luc ***@***.***> wrote: Yes esp3d V3 is compatible Fysetc SD-WIFI-PRO, and yes WebDav is working on it — Reply to this email directly, view it on GitHub <#954 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AMO6L7ZKC6OOC77SPBZPDP3X6XIPPAVCNFSM6AAAAAA53CR5IOVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM3TENBWG4YTM> . You are receiving this because you authored the thread.Message ID: ***@***.***>

3 replies

luc-github Oct 10, 2023
Maintainer

everything is described here : http://esp3d.io/esp3d/v3.x/installation/index.html
platformio is the suggested way to do it

y2kdread Oct 11, 2023
Author

Not sure if this a platform IO issue, but when I try to upload i get the following error:

warning: Calling missing SConscript without error is deprecated.
Transition by adding must_exist=False to SConscript calls.
Missing SConscript 'platformIO\extra_script.py'
File "C:\Users\bookbinder\.platformio\penv\Lib\site-packages\platformio\builder\main.py", line 167, in <module>
CONFIGURATION: https://docs.platformio.org/page/boards/espressif32/esp32dev.html
PLATFORM: Espressif 32 (6.0.1) > Espressif ESP32 Dev Module
HARDWARE: ESP32 240MHz, 320KB RAM, 4MB Flash
DEBUG: Current (cmsis-dap) External (cmsis-dap, esp-bridge, esp-prog, iot-bus-jtag, jlink, minimodule, olimex-arm-usb-ocd, olimex-arm-usb-ocd-h, olimex-arm-usb-tiny-h, olimex-jtag-tiny, tumpa)
PACKAGES:
 - framework-arduinoespressif32 @ 3.20006.221224 (2.0.6)
 - tool-esptoolpy @ 1.40400.0 (4.4.0)
 - tool-mkfatfs @ 2.0.1
 - tool-mklittlefs @ 1.203.210628 (2.3)
 - tool-mkspiffs @ 2.230.0 (2.30)
 - toolchain-xtensa-esp32 @ 8.4.0+2021r2-patch5
LDF: Library Dependency Finder -> https://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 33 compatible libraries
Scanning dependencies...
No dependencies
Building in release mode
Linking .pioenvs\esp32_8MB_wifi\firmware.elf
c:/users/bookbinder/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld.exe: .pioenvs\esp32_8MB_wifi\libFrameworkArduino.a(main.cpp.o):(.literal._Z8loopTaskPv+0x8): undefined reference to `setup()'
c:/users/bookbinder/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld.exe: .pioenvs\esp32_8MB_wifi\libFrameworkArduino.a(main.cpp.o):(.literal._Z8loopTaskPv+0xc): undefined reference to `loop()'
c:/users/bookbinder/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld.exe: .pioenvs\esp32_8MB_wifi\libFrameworkArduino.a(main.cpp.o): in function `loopTask(void*)':
C:/Users/bookbinder/.platformio/packages/framework-arduinoespressif32@3.20006.221224/cores/esp32/main.cpp:42: undefined reference to `setup()'
c:/users/bookbinder/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld.exe: C:/Users/bookbinder/.platformio/packages/framework-arduinoespressif32@3.20006.221224/cores/esp32/main.cpp:48: undefined reference to `loop()'
collect2.exe: error: ld returned 1 exit status
*** [.pioenvs\esp32_8MB_wifi\firmware.elf] Error 1

y2kdread Oct 11, 2023
Author

Got it working - I hadn't stuck all the code in my project folder.

y2kdread · 2023-10-11T21:33:09Z

y2kdread
Oct 11, 2023
Author

@luc-github - would you be willing to provide any more guidance on how to setup the config so it works with the SD-WIFI-PRO? I've spent the day working on it and can't get it to connect to the SD card for the life of me.

5 replies

luc-github Oct 11, 2023
Maintainer

so far that I remember I havee just used the pins defined in specs and was.working out of the box, no special thing to do .
Of course in webui just set the sd file panel and remove all others as this is wifi sd not usable for monitoring.
For webdav I just mapped the sd on it in configuration, and mapped as a drive in window.

what issue do you have?

y2kdread Oct 12, 2023
Author

In the files panel, I don't see the SD card listed. If I run [ESP800] I get the following showing the SD card isn't connected:

[ESP800]json
{
 "cmd": "800",
 "status": "ok",
 "data": {
  "FWVersion": "3.0.0.a225",
  "FWTarget": "unknown",
  "FWTargetID": "0",
  "Setup": "Enabled",
  "SDConnection": "none",
  "SerialProtocol": "Raw",
  "Authentication": "Disabled",
  "WebCommunication": "Synchronous",
  "WebSocketIP": "192.168.5.8",
  "WebSocketPort": "81",
  "Hostname": "esp3d",
  "WiFiMode": "STA",
  "WebUpdate": "Enabled",
  "FlashFileSystem": "LittleFS",
  "HostPath": "/",
  "Time": "none"
 }
}

This is what I have set in my configuration.h file:

// This file was generated by ESP3D-Configurator V1.0.0-a22 
/*
  configuration.h - ESP3D configuration file

  Copyright (c) 2014 Luc Lebosse. All rights reserved.

  This code is free software; you can redistribute it and/or
  modify it under the terms of the GNU Lesser General Public
  License as published by the Free Software Foundation; either
  version 2.1 of the License, or (at your option) any later version.

  This code is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  Lesser General Public License for more details.

  You should have received a copy of the GNU Lesser General Public
  License along with This code; if not, write to the Free Software
  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
*/
#ifndef _CONFIGURATION_H
#define _CONFIGURATION_H
//Setup station as default, use AP mode first if not done
//Note: need both defined to enable it
//Uncomment and edit them to define
//#define STATION_WIFI_SSID "*********"
//#define STATION_WIFI_PASSWORD "*********"

//You can also use a different config file for SSID/password
//Just save it in same location as this configuration.h
//This file is ignored by github
#if defined __has_include
#  if __has_include ("myconfig.h")
#    include "myconfig.h"
#  endif
#endif


/************************************
*
* Board description
*
* ESP Board  using ESP3D firmware
*
************************************/
// MCU=ESP32
// ESP flash size=8MB
// Form factor=Original (all pins)

/************************************
*
* Serial Communications
*
* Settings and protocols
*
************************************/

// Serial Communication protocol
// Basic serial protocol, without data change
#define COMMUNICATION_PROTOCOL RAW_SERIAL

// Serial port
#define ESP_SERIAL_OUTPUT USE_SERIAL_0

// Serial buffer size
// 1024 Bytes
// Maximum size of the serial buffer
#define SERIAL_RX_BUFFER_SIZE 1024

/************************************
*
* Target firmware
*
* Targeted firmware that ESP3D will communicate with
*
************************************/
// System type=3D printer

// Target firmware
// Undefined firmware
#define DEFAULT_FW UNKNOWN_FW

/************************************
*
* Radio mode of ESP3D
*
* The radio mode ESP3D communicate with the network
*
************************************/

// Use WiFi 
// Enable wifi communications
#define WIFI_FEATURE 

/************************************
*
* Channels of ESP3D
*
* The way ESP3D communicate
*
************************************/

// Use webserver
// Enable http server
#define HTTP_FEATURE 

// Use telnet server
// Enable telnet light (raw tcp) communications
#define TELNET_FEATURE 

// Enable notifications
// Allows to send notifications to the user
#define NOTIFICATION_FEATURE 

// Notification message when online
// The message that will be sent when the ESP is online
#define NOTIFICATION_ESP_ONLINE "Hi, %ESP_NAME% is now online at %ESP_IP%"

// Notification title message
// The title of notification
#define ESP_NOTIFICATION_TITLE "ESP3D Notification"

/************************************
*
* Discovery methods of ESP3D
*
* The discovery methods of ESP3D
*
************************************/

// Use captive portal 
// Enable captive portal in AP mode
#define CAPTIVE_PORTAL_FEATURE 

// Use mDNS discovery
// This method need `bonjour` protocol on windows, or `avahi` on linux
#define MDNS_FEATURE 

// Use Simple Service Discovery Protocol
// It is supported on Windows out of the box
#define SSDP_FEATURE 

/************************************
*
* SSDP Customization settings
*
* Customize your ESP3D
*
************************************/

// Model name
// Modele name of device
#define ESP_MODEL_NAME "ESP32"

// Model number
// Modele number of device
#define ESP_MODEL_NUMBER "ESP3D 3.0"

// Model url
// Modele url of device
#define ESP_MODEL_URL "https://www.espressif.com/en/products/devkits"

// Manufacturer name
// Manufacturer name of device
#define ESP_MANUFACTURER_NAME "Espressif Systems"

// Manufacturer url
// Manufacturer url of device
#define ESP_MANUFACTURER_URL "https://www.espressif.com"

/************************************
*
* Flash filesystem
*
* Filesystem on flash
*
************************************/

// File system type
// LittleFS
// Type of file system used by ESP3D to store files
#define FILESYSTEM_FEATURE ESP_LITTLEFS_FILESYSTEM

/************************************
*
* SD filesystem
*
* Filesystem on SD card
*
************************************/

// SD card connection
// Only your ESP board is connected to SDCard
// Does your system has SD card and how it is connected to your ESP3D
#define SD_DEVICE_CONNECTION ESP_DIRECT_SD

// SD card library
// SDFat 2 library required
#define SD_DEVICE ESP_SDFAT2

/************************************
*
* Remote access
*
* Remote filesystem access
*
************************************/

// WebDav access
// ESP3D SD
// Use WebDav to access to your filesystem
#define WEBDAV_FEATURE FS_SD

/************************************
*
* Update ESP3D
*
* Update ESP3D firmware
*
************************************/

// Enable Web Update
// Update firmware using WebUI
#define WEB_UPDATE_FEATURE 

// Enable SD card Update
// Update firmware and settings using file on SDCard
#define SD_UPDATE_FEATURE 

/************************************
*
* Levels of security
*
* How commands are allowed to be sent to ESP3D
*
************************************/

// Enable serial commands
// Allow commands to be sent to ESP3D via serial port
#define SERIAL_COMMAND_FEATURE 

/************************************
*
* Additional features
*
* Extra settings
*
************************************/

// Enable direct control pin
// Controls pins using [ESP201]
#define DIRECT_PIN_FEATURE 

/************************************
*
* Default settings for ESP3D
*
* Do not edit them
*
************************************/

// Gcode Host Feature
// This feature allows to process Gcode files like macros.
#define GCODE_HOST_FEATURE 

// Settings location
// EEPROM
// Location where ESP3D will save settings
#define ESP_SAVE_SETTINGS SETTINGS_IN_EEPROM

// Add serial task
// ESP32 need to add a task to handle serial communication
#define SERIAL_INDEPENDANT_TASK 



/************************************
*
* Development setting 
* Do not modify them for production 
************************************/

//Enable debug mode
//Do not do this when connected to printer !!!
//be noted all upload may failed if enabled
//DEBUG_OUTPUT_SERIAL0
//DEBUG_OUTPUT_SERIAL1
//DEBUG_OUTPUT_SERIAL2
//DEBUG_OUTPUT_TELNET
//DEBUG_OUTPUT_WEBSOCKET
//#define ESP_DEBUG_FEATURE DEBUG_OUTPUT_SERIAL0

#ifdef ESP_DEBUG_FEATURE
#define DEBUG_BAUDRATE 115200
#define DEBUG_ESP3D_OUTPUT_PORT  8000
#endif //ESP_DEBUG_FEATURE

//Enable benchmark report in dev console
//#define ESP_BENCHMARK_FEATURE

//Disable sanity check at compilation
//#define ESP_NO_SANITY_CHECK


/************************************
*
* Sanity checks 
* Do not modify 
************************************/

#if defined (SD_TIMESTAMP_FEATURE) || defined (FILESYSTEM_TIMESTAMP_FEATURE)
    #define TIMESTAMP_FEATURE
#endif //SD_TIMESTAMP_FEATURE || FILESYSTEM_TIMESTAMP_FEATURE 

#if defined(PRINTER_HAS_DISPLAY)
#define HAS_SERIAL_DISPLAY ""
#endif // PRINTER_HAS_DISPLAY

#if defined(CAMERA_DEVICE)
#if CAMERA_DEVICE==CAMERA_MODEL_ESP32_CAM_BOARD || CAMERA_DEVICE==CAMERA_MODEL_ESP32S2_CAM_BOARD
#define USE_BOARD_HEARDER 1
#endif // CAMERA_DEVICE==CAMERA_MODEL_ESP32_CAM_BOARD || CAMERA_DEVICE==CAMERA_MODEL_ESP32S2_CAM_BOARD
#endif // CAMERA_DEVICE

#if !defined(WIFI_FEATURE) && !defined(ETH_FEATURE)
#undef HTTP_FEATURE
#undef TELNET_FEATURE
#undef WEBDAV_FEATURE
#undef FTP_FEATURE
#undef WEB_UPDATE_FEATURE
#undef CAPTIVE_PORTAL_FEATURE
#undef SSDP_FEATURE
#undef MDNS_FEATURE
#undef NOTIFICATION_FEATURE
#endif

#endif //_CONFIGURATION_H

luc-github Oct 12, 2023
Maintainer

The report should match the configuration.h but it does not because you set :
#define SD_DEVICE_CONNECTION ESP_DIRECT_SD
but ESP800 state "SDConnection": "none",
It means you did not compiled with the configure.h you show but may be default one

Additionnaly #define SD_DEVICE_CONNECTION ESP_DIRECT_SD is incorrect it should be shared not direct because the sd is shared between ESP and printer -
I will change ESP_DIRECT_SD to ESP_ONLY_SD to avoid confusion in future

y2kdread Oct 12, 2023
Author

The first issue I identified was that I wasn't placing the configuration.h file in the correct directory, after I fixed that I was able to get past the SD card not being connection.

That being said, I am still having trouble getting the SD card detected. When I try to view the card on the dashboard it states "no SD card", I have tried a variety of pin settings and none of them seem to work. Here are a few of the different pin settings I tried to use and the associated documentation:

https://github.com/FYSETC/SD-WIFI-PRO

CS: pin 1
MOSI: pin 2
MISO: pin 7
CLK: pin 14

https://github.com/FYSETC/SdWiFiBrowser/blob/main/pins.h
CS: pin 4
MOSI: pin 13
MISO: pin 12
CLK: pin 14

and

CS: pin 13
MOSI: pin 15
MISO: pin 12
CLK: pin 14

Every time I change these settings, I run "erase flash" and re-run "upload and monitor". After this I connect to the SD card, enable "SD" in the files panel, and test. None of these work.

I've also attached my latest configuration.h in case something is missing in that.


// This file was generated by ESP3D-Configurator V1.0.0-a22 
/*
  configuration.h - ESP3D configuration file

  Copyright (c) 2014 Luc Lebosse. All rights reserved.

  This code is free software; you can redistribute it and/or
  modify it under the terms of the GNU Lesser General Public
  License as published by the Free Software Foundation; either
  version 2.1 of the License, or (at your option) any later version.

  This code is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  Lesser General Public License for more details.

  You should have received a copy of the GNU Lesser General Public
  License along with This code; if not, write to the Free Software
  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
*/
#ifndef _CONFIGURATION_H
#define _CONFIGURATION_H
//Setup station as default, use AP mode first if not done
//Note: need both defined to enable it
//Uncomment and edit them to define
//#define STATION_WIFI_SSID "*********"
//#define STATION_WIFI_PASSWORD "*********"

//You can also use a different config file for SSID/password
//Just save it in same location as this configuration.h
//This file is ignored by github
#if defined __has_include
#  if __has_include ("myconfig.h")
#    include "myconfig.h"
#  endif
#endif


/************************************
*
* Board description
*
* ESP Board  using ESP3D firmware
*
************************************/
// MCU=ESP32
// ESP flash size=8MB
// Form factor=Original (all pins)

/************************************
*
* Serial Communications
*
* Settings and protocols
*
************************************/

// Serial Communication protocol
// Basic serial protocol, without data change
#define COMMUNICATION_PROTOCOL RAW_SERIAL

// Serial port
#define ESP_SERIAL_OUTPUT USE_SERIAL_0

// Serial buffer size
// 512 Bytes
// Maximum size of the serial buffer
#define SERIAL_RX_BUFFER_SIZE 512

/************************************
*
* Target firmware
*
* Targeted firmware that ESP3D will communicate with
*
************************************/
// System type=3D printer

// Target firmware
// Marlin 2.x firmware
#define DEFAULT_FW MARLIN

/************************************
*
* Radio mode of ESP3D
*
* The radio mode ESP3D communicate with the network
*
************************************/

// Use WiFi 
// Enable wifi communications
#define WIFI_FEATURE 

/************************************
*
* Channels of ESP3D
*
* The way ESP3D communicate
*
************************************/

// Use webserver
// Enable http server
#define HTTP_FEATURE 

// Use telnet server
// Enable telnet light (raw tcp) communications
#define TELNET_FEATURE 

/************************************
*
* Discovery methods of ESP3D
*
* The discovery methods of ESP3D
*
************************************/

// Use mDNS discovery
// This method need `bonjour` protocol on windows, or `avahi` on linux
#define MDNS_FEATURE 

// Use Simple Service Discovery Protocol
// It is supported on Windows out of the box
#define SSDP_FEATURE 

/************************************
*
* SSDP Customization settings
*
* Customize your ESP3D
*
************************************/

// Model name
// Modele name of device
#define ESP_MODEL_NAME "ESP32"

// Model number
// Modele number of device
#define ESP_MODEL_NUMBER "ESP3D 3.0"

// Model url
// Modele url of device
#define ESP_MODEL_URL "https://www.espressif.com/en/products/devkits"

// Manufacturer name
// Manufacturer name of device
#define ESP_MANUFACTURER_NAME "Espressif Systems"

// Manufacturer url
// Manufacturer url of device
#define ESP_MANUFACTURER_URL "https://www.espressif.com"

/************************************
*
* Flash filesystem
*
* Filesystem on flash
*
************************************/

// File system type
// LittleFS
// Type of file system used by ESP3D to store files
#define FILESYSTEM_FEATURE ESP_LITTLEFS_FILESYSTEM

// Enable date/time on files
// Set date/time on files using SNTP or last webui connection
#define FILESYSTEM_TIMESTAMP_FEATURE 

/************************************
*
* SD filesystem
*
* Filesystem on SD card
*
************************************/

// SD card connection
// Your system has SDCard and your ESP is connected to it using sharing solution
// Does your system has SD card and how it is connected to your ESP3D
#define SD_DEVICE_CONNECTION ESP_SHARED_SD

// SD card library
// SDFat 2 library required
#define SD_DEVICE ESP_SDFAT2

// Enable date/time on files
// Set date/time on files using SNTP or last webui connection
#define SD_TIMESTAMP_FEATURE 

/************************************
*
* SD card pins
*
* SD card pins
*
************************************/

// SD card CS pin
// The pin used to select SD card in SPI mode
#define ESP_SD_CS_PIN 4

// SD card Mosi pin
// The Mosi pin used by SD in SPI mode
#define ESP_SD_MOSI_PIN 13

// SD card Miso pin
// The Miso pin used by SD in SPI mode
#define ESP_SD_MISO_PIN 12

/************************************
*
* Remote access
*
* Remote filesystem access
*
************************************/

// Enable global filesystem
// Allows to access to all filesystems fromsame location
#define GLOBAL_FILESYSTEM_FEATURE 

// WebDav access
// All filesystems
// Use WebDav to access to your filesystem
#define WEBDAV_FEATURE FS_ROOT

// FTP access
// All filesystems
// Use FTP to access to your filesystem (1 connection only)
#define FTP_FEATURE FS_ROOT

/************************************
*
* Update ESP3D
*
* Update ESP3D firmware
*
************************************/

// Enable Web Update
// Update firmware using WebUI
#define WEB_UPDATE_FEATURE 

// Enable SD card Update
// Update firmware and settings using file on SDCard
#define SD_UPDATE_FEATURE 

/************************************
*
* Levels of security
*
* How commands are allowed to be sent to ESP3D
*
************************************/

// Enable serial commands
// Allow commands to be sent to ESP3D via serial port
#define SERIAL_COMMAND_FEATURE 

/************************************
*
* Additional features
*
* Extra settings
*
************************************/

// Enable direct control pin
// Controls pins using [ESP201]
#define DIRECT_PIN_FEATURE 

/************************************
*
* Default settings for ESP3D
*
* Do not edit them
*
************************************/

// Gcode Host Feature
// This feature allows to process Gcode files like macros.
#define GCODE_HOST_FEATURE 

// Settings location
// EEPROM
// Location where ESP3D will save settings
#define ESP_SAVE_SETTINGS SETTINGS_IN_EEPROM

// Add serial task
// ESP32 need to add a task to handle serial communication
#define SERIAL_INDEPENDANT_TASK 



/************************************
*
* Development setting 
* Do not modify them for production 
************************************/

//Enable debug mode
//Do not do this when connected to printer !!!
//be noted all upload may failed if enabled
//DEBUG_OUTPUT_SERIAL0
//DEBUG_OUTPUT_SERIAL1
//DEBUG_OUTPUT_SERIAL2
//DEBUG_OUTPUT_TELNET
//DEBUG_OUTPUT_WEBSOCKET
//#define ESP_DEBUG_FEATURE DEBUG_OUTPUT_SERIAL0

#ifdef ESP_DEBUG_FEATURE
#define DEBUG_BAUDRATE 115200
#define DEBUG_ESP3D_OUTPUT_PORT  8000
#endif //ESP_DEBUG_FEATURE

//Enable benchmark report in dev console
//#define ESP_BENCHMARK_FEATURE

//Disable sanity check at compilation
//#define ESP_NO_SANITY_CHECK


/************************************
*
* Sanity checks 
* Do not modify 
************************************/

#if defined (SD_TIMESTAMP_FEATURE) || defined (FILESYSTEM_TIMESTAMP_FEATURE)
    #define TIMESTAMP_FEATURE
#endif //SD_TIMESTAMP_FEATURE || FILESYSTEM_TIMESTAMP_FEATURE 

#if defined(PRINTER_HAS_DISPLAY)
#define HAS_SERIAL_DISPLAY ""
#endif // PRINTER_HAS_DISPLAY

#if defined(CAMERA_DEVICE)
#if CAMERA_DEVICE==CAMERA_MODEL_ESP32_CAM_BOARD || CAMERA_DEVICE==CAMERA_MODEL_ESP32S2_CAM_BOARD
#define USE_BOARD_HEARDER 1
#endif // CAMERA_DEVICE==CAMERA_MODEL_ESP32_CAM_BOARD || CAMERA_DEVICE==CAMERA_MODEL_ESP32S2_CAM_BOARD
#endif // CAMERA_DEVICE

#if !defined(WIFI_FEATURE) && !defined(ETH_FEATURE)
#undef HTTP_FEATURE
#undef TELNET_FEATURE
#undef WEBDAV_FEATURE
#undef FTP_FEATURE
#undef WEB_UPDATE_FEATURE
#undef CAPTIVE_PORTAL_FEATURE
#undef SSDP_FEATURE
#undef MDNS_FEATURE
#undef NOTIFICATION_FEATURE
#endif

#endif //_CONFIGURATION_H

luc-github Oct 12, 2023
Maintainer

I just found the file I used and here pins definitions:


// SD shared flag pin
// The pin used to enable SD card for ESP board
#define ESP_FLAG_SHARED_SD_PIN 26

// Pin value
// Low
// State of SD card share pin for ESP board
#define ESP_FLAG_SHARED_SD_VALUE 0

// SD card CS pin
// The pin used to select SD card in SPI mode
#define ESP_SD_CS_PIN 13

// SD card Mosi pin
// The Mosi pin used by SD in SPI mode
#define ESP_SD_MOSI_PIN 15

// SD card Miso pin
// The Miso pin used by SD in SPI mode
#define ESP_SD_MISO_PIN 2

// SD card Sck pin
// The Sck pin used by SD in SPI mode
#define ESP_SD_SCK_PIN 14

they match the specs of https://github.com/FYSETC/SD-WIFI-PRO/blob/main/SD-WIFI-PRO%20V1.0.pdf

if you still have issue check what is the SPI divider value in webui settings / features and set to 4 it is usually an average working value it can be decreased later per your tests

y2kdread · 2023-10-12T23:21:22Z

y2kdread
Oct 12, 2023
Author

I tried that, when my SD card was still in UART mode the SD card detection timed out. When I plugged it in directly, it showed that no SD card was detected. I tried using 4 and 6 as the speed factor. I have the SD card formatted as FAT32, should it be set as something else?

…

On Thu, Oct 12, 2023 at 5:57 PM Luc ***@***.***> wrote: I just found the file I used and here pins definitions: // SD shared flag pin // The pin used to enable SD card for ESP board #define ESP_FLAG_SHARED_SD_PIN 26 // Pin value // Low // State of SD card share pin for ESP board #define ESP_FLAG_SHARED_SD_VALUE 0 // SD card CS pin // The pin used to select SD card in SPI mode #define ESP_SD_CS_PIN 13 // SD card Mosi pin // The Mosi pin used by SD in SPI mode #define ESP_SD_MOSI_PIN 15 // SD card Miso pin // The Miso pin used by SD in SPI mode #define ESP_SD_MISO_PIN 2 // SD card Sck pin // The Sck pin used by SD in SPI mode #define ESP_SD_SCK_PIN 14 if you still have issue check what is the SPI divider value in webui settings / features and set to 4 it is usually an average working value it can be decreased later per your tests — Reply to this email directly, view it on GitHub <#954 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AMO6L75GC5JT5P23Q2XELRLX7BYVNANCNFSM6AAAAAA53CR5IM> . You are receiving this because you authored the thread.Message ID: ***@***.***>

1 reply

luc-github Oct 12, 2023
Maintainer

did you set the the switch pin as in my config? it is a must , this pin is the one which define who can use the SD , esp board or printer
And again the spi speed divider is also a setting that may need to be adjusted

the sd should be formated using : https://www.sdcard.org/downloads/formatter/

y2kdread · 2023-10-13T19:57:29Z

y2kdread
Oct 13, 2023
Author

I did follow the ping configs and made a bit more progress. Now, after updating the card I do see the SD data while it is in flash mode. As soon as I remove the card and stick it in any other device, the files dashboard returns "no SD card". Any ideas on this?

config.h

// This file was generated by ESP3D-Configurator V1.0.0-a22 
/*
  configuration.h - ESP3D configuration file

  Copyright (c) 2014 Luc Lebosse. All rights reserved.

  This code is free software; you can redistribute it and/or
  modify it under the terms of the GNU Lesser General Public
  License as published by the Free Software Foundation; either
  version 2.1 of the License, or (at your option) any later version.

  This code is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  Lesser General Public License for more details.

  You should have received a copy of the GNU Lesser General Public
  License along with This code; if not, write to the Free Software
  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
*/
#ifndef _CONFIGURATION_H
#define _CONFIGURATION_H
//Setup station as default, use AP mode first if not done
//Note: need both defined to enable it
//Uncomment and edit them to define
#define STATION_WIFI_SSID "*******"
#define STATION_WIFI_PASSWORD "*******"

//You can also use a different config file for SSID/password
//Just save it in same location as this configuration.h
//This file is ignored by github
#if defined __has_include
#  if __has_include ("myconfig.h")
#    include "myconfig.h"
#  endif
#endif


/************************************
*
* Board description
*
* ESP Board  using ESP3D firmware
*
************************************/
// MCU=ESP32
// ESP flash size=8MB
// Form factor=Original (all pins)

/************************************
*
* Serial Communications
*
* Settings and protocols
*
************************************/

// Serial Communication protocol
// Basic serial protocol, without data change
#define COMMUNICATION_PROTOCOL RAW_SERIAL

// Serial port
#define ESP_SERIAL_OUTPUT USE_SERIAL_0

// Serial buffer size
// 512 Bytes
// Maximum size of the serial buffer
#define SERIAL_RX_BUFFER_SIZE 512

/************************************
*
* Target firmware
*
* Targeted firmware that ESP3D will communicate with
*
************************************/
// System type=3D printer

// Target firmware
// Marlin 2.x firmware
#define DEFAULT_FW MARLIN

/************************************
*
* Radio mode of ESP3D
*
* The radio mode ESP3D communicate with the network
*
************************************/

// Use WiFi 
// Enable wifi communications
#define WIFI_FEATURE 

/************************************
*
* Channels of ESP3D
*
* The way ESP3D communicate
*
************************************/

// Use webserver
// Enable http server
#define HTTP_FEATURE 

// Use telnet server
// Enable telnet light (raw tcp) communications
#define TELNET_FEATURE 

/************************************
*
* Discovery methods of ESP3D
*
* The discovery methods of ESP3D
*
************************************/

// Use mDNS discovery
// This method need `bonjour` protocol on windows, or `avahi` on linux
#define MDNS_FEATURE 

// Use Simple Service Discovery Protocol
// It is supported on Windows out of the box
#define SSDP_FEATURE 

/************************************
*
* SSDP Customization settings
*
* Customize your ESP3D
*
************************************/

// Model name
// Modele name of device
#define ESP_MODEL_NAME "ESP32"

// Model number
// Modele number of device
#define ESP_MODEL_NUMBER "ESP3D 3.0"

// Model url
// Modele url of device
#define ESP_MODEL_URL "https://www.espressif.com/en/products/devkits"

// Manufacturer name
// Manufacturer name of device
#define ESP_MANUFACTURER_NAME "Espressif Systems"

// Manufacturer url
// Manufacturer url of device
#define ESP_MANUFACTURER_URL "https://www.espressif.com"

/************************************
*
* Flash filesystem
*
* Filesystem on flash
*
************************************/

// File system type
// LittleFS
// Type of file system used by ESP3D to store files
#define FILESYSTEM_FEATURE ESP_LITTLEFS_FILESYSTEM

// Enable date/time on files
// Set date/time on files using SNTP or last webui connection
#define FILESYSTEM_TIMESTAMP_FEATURE 

/************************************
*
* SD filesystem
*
* Filesystem on SD card
*
************************************/

// SD card connection
// Your system has SDCard and your ESP is connected to it using sharing solution
// Does your system has SD card and how it is connected to your ESP3D
#define SD_DEVICE_CONNECTION ESP_SHARED_SD

// SD card library
// SDFat 2 library required
#define SD_DEVICE ESP_SDFAT2

// Enable date/time on files
// Set date/time on files using SNTP or last webui connection
#define SD_TIMESTAMP_FEATURE 

/************************************
*
* SD card pins
*
* SD card pins
*
************************************/

// SD shared flag pin
// The pin used to enable SD card for ESP board
#define ESP_FLAG_SHARED_SD_PIN 26

// Pin value
// Low
// State of SD card share pin for ESP board
#define ESP_FLAG_SHARED_SD_VALUE 0

// SD card CS pin
// The pin used to select SD card in SPI mode
#define ESP_SD_CS_PIN 13

// SD card Mosi pin
// The Mosi pin used by SD in SPI mode
#define ESP_SD_MOSI_PIN 15

// SD card Miso pin
// The Miso pin used by SD in SPI mode
#define ESP_SD_MISO_PIN 2

// SD card Sck pin
// The Sck pin used by SD in SPI mode
#define ESP_SD_SCK_PIN 14

/************************************
*
* Remote access
*
* Remote filesystem access
*
************************************/

// Enable global filesystem
// Allows to access to all filesystems fromsame location
#define GLOBAL_FILESYSTEM_FEATURE 

// WebDav access
// All filesystems
// Use WebDav to access to your filesystem
#define WEBDAV_FEATURE FS_ROOT

// FTP access
// All filesystems
// Use FTP to access to your filesystem (1 connection only)
#define FTP_FEATURE FS_ROOT

/************************************
*
* Update ESP3D
*
* Update ESP3D firmware
*
************************************/

// Enable Web Update
// Update firmware using WebUI
#define WEB_UPDATE_FEATURE 

// Enable SD card Update
// Update firmware and settings using file on SDCard
#define SD_UPDATE_FEATURE 

/************************************
*
* Levels of security
*
* How commands are allowed to be sent to ESP3D
*
************************************/

// Enable serial commands
// Allow commands to be sent to ESP3D via serial port
#define SERIAL_COMMAND_FEATURE 

/************************************
*
* Additional features
*
* Extra settings
*
************************************/

// Enable direct control pin
// Controls pins using [ESP201]
#define DIRECT_PIN_FEATURE 

/************************************
*
* Default settings for ESP3D
*
* Do not edit them
*
************************************/

// Gcode Host Feature
// This feature allows to process Gcode files like macros.
#define GCODE_HOST_FEATURE 

// Settings location
// EEPROM
// Location where ESP3D will save settings
#define ESP_SAVE_SETTINGS SETTINGS_IN_EEPROM

// Add serial task
// ESP32 need to add a task to handle serial communication
#define SERIAL_INDEPENDANT_TASK 



/************************************
*
* Development setting 
* Do not modify them for production 
************************************/

//Enable debug mode
//Do not do this when connected to printer !!!
//be noted all upload may failed if enabled
//DEBUG_OUTPUT_SERIAL0
//DEBUG_OUTPUT_SERIAL1
//DEBUG_OUTPUT_SERIAL2
//DEBUG_OUTPUT_TELNET
//DEBUG_OUTPUT_WEBSOCKET
//#define ESP_DEBUG_FEATURE DEBUG_OUTPUT_SERIAL0

#ifdef ESP_DEBUG_FEATURE
#define DEBUG_BAUDRATE 115200
#define DEBUG_ESP3D_OUTPUT_PORT  8000
#endif //ESP_DEBUG_FEATURE

//Enable benchmark report in dev console
//#define ESP_BENCHMARK_FEATURE

//Disable sanity check at compilation
//#define ESP_NO_SANITY_CHECK


/************************************
*
* Sanity checks 
* Do not modify 
************************************/

#if defined (SD_TIMESTAMP_FEATURE) || defined (FILESYSTEM_TIMESTAMP_FEATURE)
    #define TIMESTAMP_FEATURE
#endif //SD_TIMESTAMP_FEATURE || FILESYSTEM_TIMESTAMP_FEATURE 

#if defined(PRINTER_HAS_DISPLAY)
#define HAS_SERIAL_DISPLAY ""
#endif // PRINTER_HAS_DISPLAY

#if defined(CAMERA_DEVICE)
#if CAMERA_DEVICE==CAMERA_MODEL_ESP32_CAM_BOARD || CAMERA_DEVICE==CAMERA_MODEL_ESP32S2_CAM_BOARD
#define USE_BOARD_HEARDER 1
#endif // CAMERA_DEVICE==CAMERA_MODEL_ESP32_CAM_BOARD || CAMERA_DEVICE==CAMERA_MODEL_ESP32S2_CAM_BOARD
#endif // CAMERA_DEVICE

#if !defined(WIFI_FEATURE) && !defined(ETH_FEATURE)
#undef HTTP_FEATURE
#undef TELNET_FEATURE
#undef WEBDAV_FEATURE
#undef FTP_FEATURE
#undef WEB_UPDATE_FEATURE
#undef CAPTIVE_PORTAL_FEATURE
#undef SSDP_FEATURE
#undef MDNS_FEATURE
#undef NOTIFICATION_FEATURE
#endif

#endif //_CONFIGURATION_H

10 replies

luc-github Oct 15, 2023
Maintainer

when esp has access to SD, the printer or computer cannot see it that is normal, once esp finished to access it release sd for printer PC

y2kdread Oct 15, 2023
Author

How long should it take before the second should see the SD card again?

y2kdread Oct 15, 2023
Author

Also, what are the differences between the SDFat and Native when setting up the SD storage?

luc-github Oct 15, 2023
Maintainer

How long should it take before the second should see the SD card again?

immediatly

luc-github Oct 15, 2023
Maintainer

Also, what are the differences between the SDFat and Native when setting up the SD storage?

Native is sd library from esp it is light and slower than sdfat, I only use sdfat in alll my system

y2kdread · 2023-10-15T16:40:46Z

y2kdread
Oct 15, 2023
Author

Native is sd library from esp it is light and slower than sdfat, I only use sdfat in alll my system

Do you have any idea why the esp device would only see the SD storage when it is plugged in to be flashed using SDFat?

When i plug the SD card into the computer or another device the esp cannot see the storage using SDFat?

I am using the SD formatting utility, the pins you specified, and tried using different speed values. I am not sure if I am missing different configuration value or something else.

20 replies

luc-github Oct 19, 2023
Maintainer

that not sure , usually systems rely on insertion switch to try to mount a drive, in all case sd cannot do much by itself

It is system that polling mount if card is inserted.but they stop at first faillure

may be click on sd icon will make a mount again?

y2kdread Oct 20, 2023
Author

So far it seems to be working well. I am using it in my CPAP and was able to access the SD even after viewing the file list in ESP. I did try WebDAV but as you had mentioned the isn't working yet.

luc-github Oct 20, 2023
Maintainer

Ok cool, the webdav is actually suposed to work, it is used by other people already, but on ESP3D and ESP3DLib using a normal SD, I just did not spend time on it yet for this SD.

Additionnally the webdav code on ESP3D / ESP3DLib will be reviewed soon, I am currently writing a webdav module from scratch for another project, and adjusted the webdav features according ESP3D usage, which should improve reliability and code maintenance

What issue did you meet with WebDav ?

y2kdread Oct 20, 2023
Author

When I try accessing the files through WebDAV (mapped through windows), everything works fine. Whenever I try copying from the SD to the PC, the ESP locks up. The file transfers never completes and the web UI locks up. The only way for this to recover is to eject the SD card fully and reinsert it.

luc-github Oct 21, 2023
Maintainer

Ok I will check , I have created issue for it : #956

luc-github · 2023-11-27T10:58:21Z

luc-github
Nov 27, 2023
Maintainer

I think this topic can be closed now

0 replies

Does this project support FYSETC SD-WIFI-PRO? #954

y2kdread Oct 10, 2023

Replies: 7 comments · 39 replies

luc-github Oct 10, 2023 Maintainer

y2kdread Oct 10, 2023 Author

luc-github Oct 10, 2023 Maintainer

y2kdread Oct 11, 2023 Author

y2kdread Oct 11, 2023 Author

y2kdread Oct 11, 2023 Author

luc-github Oct 11, 2023 Maintainer

y2kdread Oct 12, 2023 Author

luc-github Oct 12, 2023 Maintainer

y2kdread Oct 12, 2023 Author

luc-github Oct 12, 2023 Maintainer

y2kdread Oct 12, 2023 Author

luc-github Oct 12, 2023 Maintainer

y2kdread Oct 13, 2023 Author

luc-github Oct 15, 2023 Maintainer

y2kdread Oct 15, 2023 Author

y2kdread Oct 15, 2023 Author

luc-github Oct 15, 2023 Maintainer

luc-github Oct 15, 2023 Maintainer

y2kdread Oct 15, 2023 Author

luc-github Oct 19, 2023 Maintainer

y2kdread Oct 20, 2023 Author

luc-github Oct 20, 2023 Maintainer

y2kdread Oct 20, 2023 Author

luc-github Oct 21, 2023 Maintainer

luc-github Nov 27, 2023 Maintainer

y2kdread
Oct 10, 2023

Replies: 7 comments 39 replies

luc-github
Oct 10, 2023
Maintainer

y2kdread
Oct 10, 2023
Author

luc-github Oct 10, 2023
Maintainer

y2kdread Oct 11, 2023
Author

y2kdread Oct 11, 2023
Author

y2kdread
Oct 11, 2023
Author

luc-github Oct 11, 2023
Maintainer

y2kdread Oct 12, 2023
Author

luc-github Oct 12, 2023
Maintainer

y2kdread Oct 12, 2023
Author

luc-github Oct 12, 2023
Maintainer

y2kdread
Oct 12, 2023
Author

luc-github Oct 12, 2023
Maintainer

y2kdread
Oct 13, 2023
Author

luc-github Oct 15, 2023
Maintainer

y2kdread Oct 15, 2023
Author

y2kdread Oct 15, 2023
Author

luc-github Oct 15, 2023
Maintainer

luc-github Oct 15, 2023
Maintainer

y2kdread
Oct 15, 2023
Author

luc-github Oct 19, 2023
Maintainer

y2kdread Oct 20, 2023
Author

luc-github Oct 20, 2023
Maintainer

y2kdread Oct 20, 2023
Author

luc-github Oct 21, 2023
Maintainer

luc-github
Nov 27, 2023
Maintainer