Skip to content
/ Alarm Public
forked from deiger/Alarm

Code to connect and control alarms by PIMA.

License

Notifications You must be signed in to change notification settings

maorcc/Alarm

 
 

Repository files navigation

PIMA Alarms

This program implements an interface for negotiation with PIMA Hunter Pro alarms.
It was built based on PIMA™'s General Specification for Home Automation & Building Management protocol Ver. 1.15.
PIMA™ is a trademark of PIMA Electronic Systems Ltd, http://www.pima-alarms.com.
This program was built with no affiliation of PIMA Electronic Systems Ltd.

Prerequisites

  1. PIMA Hunter Pro alarm™, with 32, 96 or 144 zones.
  2. PIMA Home Automation kit™ (SA-232, LCL-11A and Serial-to-USB cable), or net4pro ethernet connection. Diagram by PIMA™ ©: Diagram by PIMA™ ©
    • According to various users, the alarm can be alternatively connected using a PL2303TA USB-to-TTL cable, like this one.
    • Yet another option is to connect directly to Raspberry pi, as specified here: Diagram by @maorcc
  3. Raspberry Pi or similar, connected to the alarm through the Home Automation kit.
    • Tested on Raspbian. Other operating systems may use different path structure for the serial ports.
  4. Alarm technician login code. Unfortunately, it is not possible to connect to the alarm using a user login code.

Enabling the alarm serial port or network connection

  1. Enable extended menus:
    • Primary login code
    • NEXT
    • Technician login code
    • 5 (General parameters)
    • ENTR
    • NEXT till you get to the right P (extended menus)
    • Toggle by #
    • ENTR
    • END to exit
  2. Enable the serial port:
    • Primary login code
    • NEXT
    • Technician login code
    • 3 (Communication)
    • ENTR
    • 8 x NEXT (Serial port)
    • ENTR
    • Toggle the first L (for serial connection) or first N (for net4pro) by #
    • ENTR
    • END to exit

Setup

  1. Create an SSL certificate, if you wish to access the server through HTTPS:
    openssl req -x509 -newkey rsa:2048 -nodes -keyout key.pem -out cert.pem -days 365
  2. Install additional Python libraries:
    pip3 install crcmod paho-mqtt pyserial
  3. Download pima.py and pima_server.py, and put them in the same directory.
  4. Set run permissions to pima_server.py:
    chmod a+x pima_server.py

Run for testing

  1. Test out that you can run the server, e.g.:
    ./pima_server.py --ssl_cert cert.pem --ssl_key key.pem --port 7777 --key my_random_key --login 000000 --mqtt_host localhost
    Parameters:
    • --ssl_cert - Path to the SSL certificate file. If not set, will run a non-encrypted web server.
    • --ssl_key - Path to the SSL private key file. If not set, will get the key from the certificate file.
    • --port or -p - Port for the web server.
    • --key or -k - An arbitrary string key to authenticate the server calls.
      Consider generating a random key using uuid -v4.
    • --login or -l - The technician login code to the alarm.
    • --zones or -z - Number of zones supported by the alarm, one of 32, 96 or 144. Default is 32.
    • --serialport - Serial port, e.g. /dev/serial0. Needed if connected directly through GPIO serial.
    • --pima_host - Pima alarm hostname or IP address. Must be set if connected by ethernet.
    • --pima_port - Pima alarm port. Must be set if connected by ethernet.
    • --mqtt_host - The MQTT broker hostname or IP address. Must be set to enable MQTT.
    • --mqtt_port - The MQTT broker port. Default is 1883.
    • --mqtt_client_id - The MQTT client ID. If not set, a random client ID will be generated.
    • --mqtt_user - <user:password> for the MQTT channel. If not set, no authentication is used.
    • --mqtt_topic - The MQTT root topic. Default is "pima_alarm". The server will listen on topic <{mqtt_topic}/command> and publish to <{mqtt_topic}/status>.
    • --log_level - The minimal log level to send to syslog. Default is WARNING.
  2. Access e.g. using curl:
    curl -ik 'http://localhost:7777/pima?key=my_random_key&command=status'
    curl -ik 'http://localhost:7777/pima?key=my_random_key&command=arm&mode=home1&partitions=1'
    CGI Arguments:
    • key - The key specified on the web server startup.
    • command - Either status or arm.
      When arm is specified:
      • mode - Either full_arm, home1, home2 or disarm.
      • partitions Comma separated list of partitions. Default is 1.

Run as a service

  1. Create a dedicated directory for the script files, and move the files to it. Pass the ownership to root. e.g.:
    sudo mkdir /usr/lib/pima
    sudo mv pima_server.py pima.py key.pem cert.pem /usr/lib/pima
    sudo chown root:root /usr/lib/pima/*
    sudo pip3 install crcmod paho-mqtt pyserial
  2. Create a service configuration file (as root), e.g. /lib/systemd/system/pima.service:
    [Unit]
    Description=PIMA alarm server
    After=network.target
    
    [Service]
    ExecStart=/usr/bin/python3 -u pima_server.py --ssl_cert cert.pem --ssl_key key.pem --port 7777 --key my_random_key --login 000000 --mqtt_host localhost
    WorkingDirectory=/usr/lib/pima
    StandardOutput=inherit
    StandardError=inherit
    Restart=always
    
    [Install]
    WantedBy=multi-user.target
  3. Link to it from /etc/systemd/system/:
    sudo ln -s /lib/systemd/system/pima.service /etc/systemd/system/multi-user.target.wants/pima.service
  4. Enable and start the new service:
    sudo systemctl enable pima.service
    sudo systemctl start pima.service
  5. If you use MQTT for HomeAssistant or openHAB, the broker should now provide the updated status of the alarm, and accepts commands. Basic yaml config files for HomeAssistant are available under the hass directory.

Next steps

  1. Groovy Device Type Handlers for SmartThings integration.
  2. Support further functionality, e.g. change user codes.

About

Code to connect and control alarms by PIMA.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • Python 94.9%
  • Shell 3.8%
  • Dockerfile 1.3%