This repo contains scripts and patches to build a sample Linux image based on piCore for the Raspberry Pi Zero. The image is meant to boot very quickly (currently at around 7s), and expose a USB mass storage device (pen drive), which can be used to program a Raspberry Pi Zero with UF2 files, usually generated from Microsoft MakeCode and in particular from MakeCode Arcade.
The image was tested on a Raspberry Pi Zero Rev 1.3 and Zero W Rev 1.3. It could theoretically work on the original Pi A/A+, but wasn't tested. Other models lack the OTG ID pin, and thus cannot be used in USB device mode.
PRs are welcome!
Building the image requires Docker.
Go to image/ and run ./build.sh. The image will land in built/boot/*.
After you're done building, copy one of the arcade.cfg files in cfg/ folder
to built/boot/* so that it ends up on the SD card.
You can also create your own arcade.cfg file if you have the buttons
connected differently.
The pin numbers in there are BCM pin numbers, not physical pin numbers, see https://pinout.xyz/
It's also possible to use regular Linux key codes if your buttons appear as a standard keyboard.
This is enabled by setting SCAN_CODES=/dev/input/event1 or similar.
Use evtest program to figure out the scan codes and use these scan codes instead of BCM pin numbers.
All files in built/boot/ need to be copied to a FAT32-formatted SD card.
There is no ext4 partition to worry about, and you don't need to use any
special software to "burn" the image.
The files need to sit in the root folder of the SD card, i.e.,
you should have file d:/9.0.3.gz, d:/cmdline.txt, as well
as d:/arcade.cfg (if your SD drive is d:/; on macOS it will
be /Volumes/NO NAME/9.0.3.gz etc).
Regular SD cards come preformatted as FAT32. If you have a previous Raspberry Pi image on the card you can format it, or just move all files in the first partition into a sub-folder if it's reasonably big.
Any SD card should do. You don't need much space (currently around 13MB), and the Pi will only read a few MBs upon startup, so the speed isn't very important.
If you want to build the Docker image (pext/rpi) yourself,
use the docker/build.sh script. Usually, you can just pull it
from Docker Hub (which will just happen automatically).
The image is based on
sdthirlwall/raspberry-pi-cross-compiler
and contains stock piCore 9.0.3 and sources of its kernel.
Sources are here: https://github.com/microsoft/pxt-arcade-cabinet-menu
- 4 player configuration test https://github.com/microsoft/pxt-arcade/blob/master/docs/hardware/raspberry-pi/cardboard-control-panel/configurator.ts
- Another program for testing buttons:
https://arcade.makecode.com/81381-26574-00648-24234
By default gdbserver runs on the serial port exposed by the g_multi gadget.
To connect to it on macOS run arm-linux-gnueabihf-gdb and then do the following:
(gdb) target extended-remote /dev/cu.usbmodem141123
where the numbers at the end will vary. Do not use /dev/tty.usbmodem..., as this will
just hang.
The contents of this repo are released under the MIT license.
The images that you build will contain software under all sorts of licenses, including GPL.
This project welcomes contributions and suggestions. Most contributions require you to agree to a Contributor License Agreement (CLA) declaring that you have the right to, and actually do, grant us the rights to use your contribution. For details, visit https://cla.microsoft.com.
When you submit a pull request, a CLA-bot will automatically determine whether you need to provide a CLA and decorate the PR appropriately (e.g., label, comment). Simply follow the instructions provided by the bot. You will only need to do this once across all repos using our CLA.
This project has adopted the Microsoft Open Source Code of Conduct. For more information see the Code of Conduct FAQ or contact opencode@microsoft.com with any additional questions or comments.