Skip to content

A simple 28C16 EEPROM writer for Arduino Nano or Uno

License

Notifications You must be signed in to change notification settings

moefh/eeprom_writer

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

11 Commits
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

EEPROM Writer

A simple 28C16 EEPROM writer for Arduino Nano or Uno based on Ben Eater's EEPROM programmer.

This project includes:

  • An arduino project that accepts commands from the serial USB to read or write the EEPROM
  • A command line tool for Linux (might work on Mac?) written in C to read and write data files to the EEPROM

The circuit is heavily based on Ben Eater's circuit with a few changes to make it more robust when using an Arduino Uno. The main changes are:

  • Don't use pin 13 for write enable (which is used by the Arduino during boot to blink the builtin LED). Instead we use the digital output of analog pins A0 to A2 to control the EEPROM chip enable, write enable and output enable pins.
  • Add 10k resistors to pull down the shift register inputs do they don't float wildly while the Arduino is starting
  • Add 10k resistors to pull up the enable pins of the EEPROM (chip enable, write enable and output enable) to make it more reliable (especially when arduino is starting up).

Circuit

Schematic

Breadboard Photo

Command Line Tool

The command line tool is written in C. To build it, just enter the cmdline directory and type make (make sure you have the necessary stuff installed, like build-essential if using Ubuntu).

The available commands are:

Show EEPROM contents

eeprom dump [ADDRESS [LENGTH]]

Sends the contents of the EEPROM to the standard output formatted as traditional hexdump output. The default ADDRESS is 0 and the default LENGTH to the end of the EEPROM. Examples:

./eeprom dump              # the whole EEPROM
./eeprom dump 0 64         # 64 bytes starting at address 0
./eeprom dump 0x200 0x80   # 128 bytes (0x80) starting at address 512 (0x200)

Read EEPROM contents to file

eeprom read FILE [ADDRESS [LENGTH]]

Reads the contents of the EEPROM and writes the data to a file. The default ADDRESS is 0 and the default LENGTH is the length of the EEPROM. Examples:

./eeprom read file.bin           # the whole EEPROM
./eeprom read file.bin 0 64      # the first 64 bytes
./eeprom read file.bin 100 0x20  # 32 bytes (0x20) starting at address 100

Write file to EEPROM

eeprom write FILE [ADDRESS]

Writes the whole contents of a file to the EEPROM. The default ADDRESS is 0. Examples:

./eeprom write file.bin          # writes to start of the EEPROM
./eeprom write file.bin 0x400    # writes to the address 1024 (0x400)

Arduino Project

The Arduino program (found in arduino/eeprom_writer) waits for commands from the serial and executes them. The prompt

*READY

is written to the serial port at the start and after every command is executed successfully. If a command fails, the prompt

*ERROR: <message>

is written to the serial port.

The available commands are:

Dump

d ADDRESS LENGTH

Reads data from ADDRESS to ADDRESS+LENGTH and sends it to the serial it in a classic "hexdump" format. Both numbers must be in hexadecimal.

Read

r ADDRESS LENGTH

Reads data from ADDRESS to ADDRESS+LENGTH and sends it to the serial it in a stream of hex digits with no formatting. Both numbers must be in hexadecimal.

Write

w ADDRESS LENGTH

Reads LENGTH pairs of hex digits (each pair representing a byte) from the serial and writes the bytes to the EEPROM starting at address ADDRESS. Both numbers must be in hexadecimal. I the data is not sent in 5 seconds, a timeout error is written to the serial and no data is written.

About

A simple 28C16 EEPROM writer for Arduino Nano or Uno

Topics

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published