Merge changes from MarlinFirmware/Marlin

Marlin/Configuration.h

@@ -35,7 +35,7 @@
  *
  * Advanced settings can be found in Configuration_adv.h
  */
-#define CONFIGURATION_H_VERSION 02010000
+#define CONFIGURATION_H_VERSION 02010100
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -57,15 +57,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -157,13 +148,12 @@
  *
  * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC2209/TMC2209_STANDALONE for TMC2226 drivers.
  *
- * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
- *          TB6560, TB6600, TMC2100,
+ * Options: A4988, A5984, DRV8825, LV8729, TB6560, TB6600, TMC2100,
  *          TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  *          TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
- * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
+ * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
 #define X_DRIVER_TYPE  A4988
 #define Y_DRIVER_TYPE  A4988
@@ -865,7 +855,135 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
-// Enable for an articulated robot (robot arm). Joints are directly mapped to axes (no kinematics).
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
 //#define ARTICULATED_ROBOT_ARM
 
 // For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
@@ -1224,6 +1342,27 @@
   #define Z_PROBE_RETRACT_X X_MAX_POS
 #endif
 
+/**
+ * Magnetically Mounted Probe
+ * For probes such as Euclid, Klicky, Klackender, etc.
+ */
+//#define MAG_MOUNTED_PROBE
+#if ENABLED(MAG_MOUNTED_PROBE)
+  #define PROBE_DEPLOY_FEEDRATE (133*60)  // (mm/min) Probe deploy speed
+  #define PROBE_STOW_FEEDRATE   (133*60)  // (mm/min) Probe stow speed
+
+  #define MAG_MOUNTED_DEPLOY_1 { PROBE_DEPLOY_FEEDRATE, { 245, 114, 30 } }  // Move to side Dock & Attach probe
+  #define MAG_MOUNTED_DEPLOY_2 { PROBE_DEPLOY_FEEDRATE, { 210, 114, 30 } }  // Move probe off dock
+  #define MAG_MOUNTED_DEPLOY_3 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_4 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_DEPLOY_5 { PROBE_DEPLOY_FEEDRATE, {   0,   0,  0 } }  // Extra move if needed
+  #define MAG_MOUNTED_STOW_1   { PROBE_STOW_FEEDRATE,   { 245, 114, 20 } }  // Move to dock
+  #define MAG_MOUNTED_STOW_2   { PROBE_STOW_FEEDRATE,   { 245, 114,  0 } }  // Place probe beside remover
+  #define MAG_MOUNTED_STOW_3   { PROBE_STOW_FEEDRATE,   { 230, 114,  0 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_4   { PROBE_STOW_FEEDRATE,   { 210, 114, 20 } }  // Side move to remove probe
+  #define MAG_MOUNTED_STOW_5   { PROBE_STOW_FEEDRATE,   {   0,   0,  0 } }  // Extra move if needed
+#endif
+
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
 // When the pin is defined you can use M672 to set/reset the probe sensitivity.
 //#define DUET_SMART_EFFECTOR
@@ -1239,9 +1378,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }
@@ -1816,7 +1983,7 @@
 //#define LCD_BED_TRAMMING
 
 #if ENABLED(LCD_BED_TRAMMING)
-  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 }  // (mm) Left, Front, Right, Back insets
+  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
   #define BED_TRAMMING_HEIGHT      0.0        // (mm) Z height of nozzle at leveling points
   #define BED_TRAMMING_Z_HOP       4.0        // (mm) Z height of nozzle between leveling points
   //#define BED_TRAMMING_INCLUDE_CENTER       // Move to the center after the last corner
@@ -2631,6 +2798,12 @@
 //
 //#define SILVER_GATE_GLCD_CONTROLLER
 
+//
+// eMotion Tech LCD with SD
+// https://www.reprap-france.com/produit/1234568748-ecran-graphique-128-x-64-points-2-1
+//
+//#define EMOTION_TECH_LCD
+
 //=============================================================================
 //==============================  OLED Displays  ==============================
 //=============================================================================
@@ -2911,7 +3084,6 @@
 //
 //#define DWIN_CREALITY_LCD           // Creality UI
 //#define DWIN_LCD_PROUI              // Pro UI by MRiscoC
-//#define DWIN_CREALITY_LCD_JYERSUI   // Jyers UI by Jacob Myers
 //#define DWIN_MARLINUI_PORTRAIT      // MarlinUI (portrait orientation)
 //#define DWIN_MARLINUI_LANDSCAPE     // MarlinUI (landscape orientation)